diff --git b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt new file mode 100644 index 0000000..ebf0d47 --- /dev/null +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt @@ -0,0 +1,48 @@ +The generic power sequence library + +Some hard-wired devices (eg USB/MMC) need to do power sequence before +the device can be enumerated on the bus, the typical power sequence +like: enable USB PHY clock, toggle reset pin, etc. But current +Linux device driver lacks of such code to do it, it may cause some +hard-wired devices works abnormal or can't be recognized by +controller at all. The power sequence will be done before this device +can be found at the bus. + +The power sequence properties is under the device node. + +Optional properties: +- clocks: the input clocks for device. +- reset-gpios: Should specify the GPIO for reset. +- reset-duration-us: the duration in microsecond for assert reset signal. + +Below is the example of USB power sequence properties on USB device +nodes which have two level USB hubs. + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + genesys: hub@1 { + compatible = "usb5e3,608"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; + + #address-cells = <1>; + #size-cells = <0>; + asix: ethernet@1 { + compatible = "usbb95,1708"; + reg = <1>; + + clocks = <&clks IMX6SX_CLK_IPG>; + reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */ + reset-duration-us = <15>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt index 036be17..cb85f82 100644 --- a/Documentation/devicetree/bindings/usb/usb-device.txt +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -65,6 +65,9 @@ Required properties for host-controller nodes with device nodes: - #address-cells: shall be 1 - #size-cells: shall be 0 +Optional properties: +power sequence properties, see +Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt for detail Example: @@ -72,9 +75,13 @@ Example: #address-cells = <1>; #size-cells = <0>; - hub@1 { /* hub connected to port 1 */ + genesys: hub@1 { /* hub connected to port 1 */ compatible = "usb5e3,608"; reg = <1>; + + clocks = <&clks IMX6SX_CLK_CKO>; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */ + reset-duration-us = <10>; }; device@2 { /* device connected to port 2 */ diff --git b/Documentation/power/power-sequence/design.rst b/Documentation/power/power-sequence/design.rst new file mode 100644 index 0000000..554608e --- /dev/null +++ b/Documentation/power/power-sequence/design.rst @@ -0,0 +1,54 @@ +==================================== +Power Sequence Library +==================================== + +:Date: Feb, 2017 +:Author: Peter Chen + + +Introduction +============ + +We have an well-known problem that the device needs to do a power +sequence before it can be recognized by related host, the typical +examples are hard-wired mmc devices and usb devices. The host controller +can't know what kinds of this device is in its bus if the power +sequence has not done, since the related devices driver's probe calling +is determined by runtime according to eunumeration results. Besides, +the devices may have custom power sequence, so the power sequence library +which is independent with the devices is needed. + +Design +============ + +The power sequence library includes the core file and customer power +sequence library. The core file exports interfaces are called by +host controller driver for power sequence and customer power sequence +library files to register its power sequence instance to global +power sequence list. The custom power sequence library creates power +sequence instance and implement custom power sequence. + +Since the power sequence describes hardware design, the description is +located at board description file, eg, device tree dts file. And +a specific power sequence belongs to device, so its description +is under the device node, please refer to: +Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt + +Custom power sequence library allocates one power sequence instance at +bootup periods using postcore_initcall, this static allocated instance is +used to compare with device-tree (DT) node to see if this library can be +used for the node or not. When the result is matched, the core API will +try to get resourses (->get, implemented at each library) for power +sequence, if all resources are got, it will try to allocate another +instance for next possible request from host driver. + +Then, the host controller driver can carry out power sequence on for this +DT node, the library will do corresponding operations, like open clocks, +toggle gpio, etc. The power sequence off routine will close and free the +resources, and is called when the parent is removed. And the power +sequence suspend and resume routine can be called at host driver's +suspend and resume routine if needed. + +The exported interfaces +.. kernel-doc:: drivers/power/pwrseq/core.c + :export: diff --git a/MAINTAINERS b/MAINTAINERS index 1407008..08016c7 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -13048,6 +13048,15 @@ F: drivers/firmware/psci/ F: include/linux/psci.h F: include/uapi/linux/psci.h +POWER SEQUENCE LIBRARY +M: Peter Chen +T: git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git +L: linux-pm@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/power/pwrseq/ +F: drivers/power/pwrseq/ +F: include/linux/power/pwrseq.h + POWER SUPPLY CLASS/SUBSYSTEM and DRIVERS M: Sebastian Reichel L: linux-pm@vger.kernel.org diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile index 0b3cd7a..87a8b8d 100644 --- a/arch/arm/boot/Makefile +++ b/arch/arm/boot/Makefile @@ -29,6 +29,10 @@ export ZRELADDR INITRD_PHYS PARAMS_PHYS targets := Image zImage xipImage bootpImage uImage +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + ifeq ($(CONFIG_XIP_KERNEL),y) cmd_deflate_xip_data = $(CONFIG_SHELL) -c \ diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b21b3a6..07e811d 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,4 +1,9 @@ # SPDX-License-Identifier: GPL-2.0 + +ifeq ($(CONFIG_OF_OVERLAY),y) +DTC_FLAGS += -@ +endif + dtb-$(CONFIG_ARCH_ALPINE) += \ alpine-db.dtb dtb-$(CONFIG_MACH_ARTPEC6) += \ @@ -739,6 +744,12 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-base0033.dtb \ am335x-bone.dtb \ am335x-boneblack.dtb \ + am335x-bonegreen-wireless-uboot-univ.dtb \ + am335x-boneblack-uboot-univ.dtb \ + am335x-bone-uboot-univ.dtb \ + am335x-boneblack-uboot.dtb \ + am335x-bonegreen-gateway.dtb \ + am335x-abbbi.dtb \ am335x-boneblack-wireless.dtb \ am335x-boneblue.dtb \ am335x-bonegreen.dtb \ @@ -769,6 +780,7 @@ dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-duovero-parlor.dtb \ omap4-kc1.dtb \ omap4-panda.dtb \ + omap4-panda-es-b3.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ omap4-sdp.dtb \ @@ -789,6 +801,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \ omap5-uevm.dtb dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-beagle-x15.dtb \ + am5729-beagleboneai.dtb \ am57xx-beagle-x15-revb1.dtb \ am57xx-beagle-x15-revc.dtb \ am57xx-cl-som-am57x.dtb \ diff --git b/arch/arm/boot/dts/am335x-abbbi.dts b/arch/arm/boot/dts/am335x-abbbi.dts new file mode 100644 index 0000000..870ce85 --- /dev/null +++ b/arch/arm/boot/dts/am335x-abbbi.dts @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright 2015 Konsulko Group + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" + +/ { + model = "Arrow BeagleBone Black Industrial"; + compatible = "arrow,am335x-abbbi", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-abbbi.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&mmc2 { + vmmc-supply = <&vmmcsd_fixed>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_pins>; + bus-width = <8>; + status = "okay"; +}; + +&am33xx_pinmux { + adi_hdmi_bbbi_pins: adi_hdmi_bbbi_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + >; + }; + + mcasp0_pins: mcasp0_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/ + AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */ + >; + }; +}; + +&lcdc { + status = "okay"; + + /* If you want to get 24 bit RGB and 16 BGR mode instead of + * current 16 bit RGB and 24 BGR modes, set the propety + * below to "crossed" and uncomment the video-ports -property + * in tda19988 node. + */ + blue-and-red-wiring = "straight"; + + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&i2c0 { + adv7511: adv7511@39 { + compatible = "adi,adv7511"; + reg = <0x39>; + + pinctrl-names = "default"; + pinctrl-0 = <&adi_hdmi_bbbi_pins>; + + /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ + /* video-ports = <0x234501>; */ + + #sound-dai-cells = <0>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; +}; + +&rtc { + system-power-controller; +}; + +&mcasp0 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + status = "okay"; + op-mode = <0>; /* MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */ + 0 0 1 0 + >; + tx-num-evt = <1>; + rx-num-evt = <1>; +}; + +/ { + clk_mcasp0_fixed: clk_mcasp0_fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24576000>; + }; + + clk_mcasp0: clk_mcasp0 { + #clock-cells = <0>; + compatible = "gpio-gate-clock"; + clocks = <&clk_mcasp0_fixed>; + enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */ + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "TI BeagleBone Black"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + + dailink0_master: simple-audio-card,cpu { + sound-dai = <&mcasp0>; + clocks = <&clk_mcasp0>; + }; + + simple-audio-card,codec { + sound-dai = <&adv7511>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi new file mode 100644 index 0000000..90f13e0 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-no-capemgr.dtsi @@ -0,0 +1,373 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ + +/ { + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + chosen { + stdout-path = &uart0; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds_s0>; + + compatible = "gpio-leds"; + + led2 { + label = "beaglebone:green:usr0"; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led3 { + label = "beaglebone:green:usr1"; + gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led4 { + label = "beaglebone:green:usr2"; + gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu0"; + default-state = "off"; + }; + + led5 { + label = "beaglebone:green:usr3"; + gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + }; + + vmmcsd_fixed: fixedregulator0 { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&am33xx_pinmux { + user_leds_s0: user_leds_s0 { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a5.gpio1_21 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_a6.gpio1_22 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a7.gpio1_23 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gpmc_a8.gpio1_24 */ + >; + }; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0) /* i2c0_sda.i2c0_sda */ + AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLUP, MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* uart1_ctsn.i2c2_sda */ + AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* uart1_rtsn.i2c2_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLUP, MUX_MODE0) + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* MDIO */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0) + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT, MUX_MODE7) /* spio0_cs1.gpio0_6 */ + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0) + >; + }; + + emmc_pins: pinmux_emmc_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "peripheral"; + interrupts-extended = <&intc 18 &tps 0>; + interrupt-names = "mc", "vbus"; +}; + +&usb1 { + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + + baseboard_eeprom: baseboard_eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + + #address-cells = <1>; + #size-cells = <1>; + baseboard_data: baseboard_data@0 { + reg = <0 0x100>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + status = "okay"; + clock-frequency = <100000>; +}; + + +/include/ "tps65217.dtsi" + +&tps { + /* + * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only + * mode") at poweroff. Most BeagleBone versions do not support RTC-only + * mode and risk hardware damage if this mode is entered. + * + * For details, see linux-omap mailing list May 2015 thread + * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller + * In particular, messages: + * http://www.spinics.net/lists/linux-omap/msg118585.html + * http://www.spinics.net/lists/linux-omap/msg118615.html + * + * You can override this later with + * &tps { /delete-property/ ti,pmic-shutdown-controller; } + * if you want to use RTC-only mode and made sure you are not affected + * by the hardware problems. (Tip: double-check by performing a current + * measurement after shutdown: it should be less than 1 mA.) + */ + + interrupts = <7>; /* NMI */ + interrupt-parent = <&intc>; + + ti,pmic-shutdown-controller; + + charger { + status = "okay"; + }; + + pwrbutton { + status = "okay"; + }; + + regulators { + dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1351500>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3a"; + regulator-always-on; + }; + }; +}; + +&cpsw_emac0 { + phy-handle = <ðphy0>; + phy-mode = "mii"; +}; + +&mac { + slaves = <1>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&mmc1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; +}; + +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +&rtc { + clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>; + clock-names = "ext-clk", "int-clk"; + system-power-controller; +}; diff --git b/arch/arm/boot/dts/am335x-bone-common-univ.dtsi b/arch/arm/boot/dts/am335x-bone-common-univ.dtsi new file mode 100644 index 0000000..2c448f8 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-common-univ.dtsi @@ -0,0 +1,2940 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ + +&am33xx_pinmux { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + + /* P8_02 GND */ + + + /* P8_03 (ZCZ ball R9) emmc */ + P8_03_default_pin: pinmux_P8_03_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pin: pinmux_P8_03_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pu_pin: pinmux_P8_03_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pd_pin: pinmux_P8_03_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_input_pin: pinmux_P8_03_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + + /* P8_04 (ZCZ ball T9) emmc */ + P8_04_default_pin: pinmux_P8_04_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pin: pinmux_P8_04_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pu_pin: pinmux_P8_04_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pd_pin: pinmux_P8_04_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_input_pin: pinmux_P8_04_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + + /* P8_05 (ZCZ ball R8) emmc */ + P8_05_default_pin: pinmux_P8_05_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pin: pinmux_P8_05_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pu_pin: pinmux_P8_05_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pd_pin: pinmux_P8_05_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_input_pin: pinmux_P8_05_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + + /* P8_06 (ZCZ ball T8) emmc */ + P8_06_default_pin: pinmux_P8_06_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pin: pinmux_P8_06_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pu_pin: pinmux_P8_06_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pd_pin: pinmux_P8_06_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_input_pin: pinmux_P8_06_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + + /* P8_07 (ZCZ ball R7) gpio2_2 */ + P8_07_default_pin: pinmux_P8_07_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pin: pinmux_P8_07_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pu_pin: pinmux_P8_07_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pd_pin: pinmux_P8_07_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_input_pin: pinmux_P8_07_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_timer_pin: pinmux_P8_07_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_advn_ale.timer4 */ + + /* P8_08 (ZCZ ball T7) gpio2_3 */ + P8_08_default_pin: pinmux_P8_08_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pin: pinmux_P8_08_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pu_pin: pinmux_P8_08_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pd_pin: pinmux_P8_08_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_input_pin: pinmux_P8_08_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_timer_pin: pinmux_P8_08_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_oen_ren.timer7 */ + + /* P8_09 (ZCZ ball T6) gpio2_5 */ + P8_09_default_pin: pinmux_P8_09_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pin: pinmux_P8_09_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pu_pin: pinmux_P8_09_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pd_pin: pinmux_P8_09_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_input_pin: pinmux_P8_09_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_timer_pin: pinmux_P8_09_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_be0n_cle.timer5 */ + + /* P8_10 (ZCZ ball U6) gpio2_4 */ + P8_10_default_pin: pinmux_P8_10_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pin: pinmux_P8_10_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pu_pin: pinmux_P8_10_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pd_pin: pinmux_P8_10_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_input_pin: pinmux_P8_10_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_timer_pin: pinmux_P8_10_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_wen.timer6 */ + + /* P8_11 (ZCZ ball R12) gpio1_13 */ + P8_11_default_pin: pinmux_P8_11_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pin: pinmux_P8_11_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pu_pin: pinmux_P8_11_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pd_pin: pinmux_P8_11_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_input_pin: pinmux_P8_11_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_qep_pin: pinmux_P8_11_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad13.eqep2b_in */ + P8_11_pruout_pin: pinmux_P8_11_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad13.pru0_out15 */ + + /* P8_12 (ZCZ ball T12) gpio1_12 */ + P8_12_default_pin: pinmux_P8_12_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pin: pinmux_P8_12_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pu_pin: pinmux_P8_12_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pd_pin: pinmux_P8_12_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_input_pin: pinmux_P8_12_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_qep_pin: pinmux_P8_12_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad12.eqep2a_in */ + P8_12_pruout_pin: pinmux_P8_12_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad12.pru0_out14 */ + + /* P8_13 (ZCZ ball T10) gpio0_23 */ + P8_13_default_pin: pinmux_P8_13_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pin: pinmux_P8_13_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pu_pin: pinmux_P8_13_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pd_pin: pinmux_P8_13_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_input_pin: pinmux_P8_13_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_pwm_pin: pinmux_P8_13_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad9.ehrpwm2b */ + + /* P8_14 (ZCZ ball T11) gpio0_26 */ + P8_14_default_pin: pinmux_P8_14_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P8_14_gpio_pin: pinmux_P8_14_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P8_14_gpio_pu_pin: pinmux_P8_14_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P8_14_gpio_pd_pin: pinmux_P8_14_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P8_14_gpio_input_pin: pinmux_P8_14_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P8_14_pwm_pin: pinmux_P8_14_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad10.ehrpwm2_tripzone_input */ + + /* P8_15 (ZCZ ball U13) gpio1_15 */ + P8_15_default_pin: pinmux_P8_15_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_input_pin: pinmux_P8_15_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad15.eqep2_strobe */ + P8_15_pru_ecap_pin: pinmux_P8_15_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_ad15.pr1_ecap0_ecap_capin_apwm_o */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad15.pru0_in15 */ + + /* P8_16 (ZCZ ball V13) gpio1_14 */ + P8_16_default_pin: pinmux_P8_16_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pin: pinmux_P8_16_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pu_pin: pinmux_P8_16_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pd_pin: pinmux_P8_16_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_input_pin: pinmux_P8_16_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_qep_pin: pinmux_P8_16_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad14.eqep2_index */ + P8_16_pruin_pin: pinmux_P8_16_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad14.pru0_in14 */ + + /* P8_17 (ZCZ ball U12) gpio0_27 */ + P8_17_default_pin: pinmux_P8_17_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P8_17_gpio_pin: pinmux_P8_17_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P8_17_gpio_pu_pin: pinmux_P8_17_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P8_17_gpio_pd_pin: pinmux_P8_17_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P8_17_gpio_input_pin: pinmux_P8_17_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P8_17_pwm_pin: pinmux_P8_17_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad11.ehrpwm0_synco */ + + /* P8_18 (ZCZ ball V12) gpio2_1 */ + P8_18_default_pin: pinmux_P8_18_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pin: pinmux_P8_18_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pu_pin: pinmux_P8_18_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pd_pin: pinmux_P8_18_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_input_pin: pinmux_P8_18_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + + /* P8_19 (ZCZ ball U10) gpio0_22 */ + P8_19_default_pin: pinmux_P8_19_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pin: pinmux_P8_19_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pu_pin: pinmux_P8_19_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pd_pin: pinmux_P8_19_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_input_pin: pinmux_P8_19_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_pwm_pin: pinmux_P8_19_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad8.ehrpwm2a */ + + /* P8_20 (ZCZ ball V9) emmc */ + P8_20_default_pin: pinmux_P8_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pin: pinmux_P8_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pu_pin: pinmux_P8_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pd_pin: pinmux_P8_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_input_pin: pinmux_P8_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_pruout_pin: pinmux_P8_20_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_csn2.pru1_out13 */ + P8_20_pruin_pin: pinmux_P8_20_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_csn2.pru1_in13 */ + + /* P8_21 (ZCZ ball U9) emmc */ + P8_21_default_pin: pinmux_P8_21_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pin: pinmux_P8_21_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pu_pin: pinmux_P8_21_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pd_pin: pinmux_P8_21_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_input_pin: pinmux_P8_21_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_pruout_pin: pinmux_P8_21_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_csn1.pru1_out12 */ + P8_21_pruin_pin: pinmux_P8_21_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_csn1.pru1_in12 */ + + /* P8_22 (ZCZ ball V8) emmc */ + P8_22_default_pin: pinmux_P8_22_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pin: pinmux_P8_22_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pu_pin: pinmux_P8_22_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pd_pin: pinmux_P8_22_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_input_pin: pinmux_P8_22_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + + /* P8_23 (ZCZ ball U8) emmc */ + P8_23_default_pin: pinmux_P8_23_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pin: pinmux_P8_23_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pu_pin: pinmux_P8_23_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pd_pin: pinmux_P8_23_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_input_pin: pinmux_P8_23_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + + /* P8_24 (ZCZ ball V7) emmc */ + P8_24_default_pin: pinmux_P8_24_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pin: pinmux_P8_24_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pu_pin: pinmux_P8_24_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pd_pin: pinmux_P8_24_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_input_pin: pinmux_P8_24_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + + /* P8_25 (ZCZ ball U7) emmc */ + P8_25_default_pin: pinmux_P8_25_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pin: pinmux_P8_25_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pu_pin: pinmux_P8_25_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pd_pin: pinmux_P8_25_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_input_pin: pinmux_P8_25_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + + /* P8_26 (ZCZ ball V6) gpio1_29 */ + P8_26_default_pin: pinmux_P8_26_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x087c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn0.gpio1_29 */ + P8_26_gpio_pin: pinmux_P8_26_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x087c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn0.gpio1_29 */ + P8_26_gpio_pu_pin: pinmux_P8_26_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x087c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn0.gpio1_29 */ + P8_26_gpio_pd_pin: pinmux_P8_26_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x087c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn0.gpio1_29 */ + P8_26_gpio_input_pin: pinmux_P8_26_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x087c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn0.gpio1_29 */ + + /* P8_27 (ZCZ ball U5) hdmi */ + P8_27_default_pin: pinmux_P8_27_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pin: pinmux_P8_27_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pu_pin: pinmux_P8_27_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pd_pin: pinmux_P8_27_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_input_pin: pinmux_P8_27_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_pruout_pin: pinmux_P8_27_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_vsync.pru1_out8 */ + P8_27_pruin_pin: pinmux_P8_27_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_vsync.pru1_in8 */ + + /* P8_28 (ZCZ ball V5) hdmi */ + P8_28_default_pin: pinmux_P8_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pin: pinmux_P8_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pu_pin: pinmux_P8_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pd_pin: pinmux_P8_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_input_pin: pinmux_P8_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_pruout_pin: pinmux_P8_28_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_pclk.pru1_out10 */ + P8_28_pruin_pin: pinmux_P8_28_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_pclk.pru1_in10 */ + + /* P8_29 (ZCZ ball R5) hdmi */ + P8_29_default_pin: pinmux_P8_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pin: pinmux_P8_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pu_pin: pinmux_P8_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pd_pin: pinmux_P8_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_input_pin: pinmux_P8_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_pruout_pin: pinmux_P8_29_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_hsync.pru1_out9 */ + P8_29_pruin_pin: pinmux_P8_29_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_hsync.pru1_in9 */ + + /* P8_30 (ZCZ ball R6) hdmi */ + P8_30_default_pin: pinmux_P8_30_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pin: pinmux_P8_30_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pu_pin: pinmux_P8_30_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pd_pin: pinmux_P8_30_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_input_pin: pinmux_P8_30_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_pruout_pin: pinmux_P8_30_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_ac_bias_en.pru1_out11 */ + P8_30_pruin_pin: pinmux_P8_30_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE6) >; }; /* lcd_ac_bias_en.pru1_in11 */ + + /* P8_31 (ZCZ ball V4) hdmi */ + P8_31_default_pin: pinmux_P8_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pin: pinmux_P8_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pu_pin: pinmux_P8_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pd_pin: pinmux_P8_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_input_pin: pinmux_P8_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_qep_pin: pinmux_P8_31_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data14.eqep1_index */ + P8_31_uart_pin: pinmux_P8_31_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data14.uart5_rxd */ + + /* P8_32 (ZCZ ball T5) hdmi */ + P8_32_default_pin: pinmux_P8_32_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pin: pinmux_P8_32_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pu_pin: pinmux_P8_32_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pd_pin: pinmux_P8_32_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_input_pin: pinmux_P8_32_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_qep_pin: pinmux_P8_32_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data15.eqep1_strobe */ + + /* P8_33 (ZCZ ball V3) hdmi */ + P8_33_default_pin: pinmux_P8_33_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pin: pinmux_P8_33_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pu_pin: pinmux_P8_33_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pd_pin: pinmux_P8_33_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_input_pin: pinmux_P8_33_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_qep_pin: pinmux_P8_33_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data13.eqep1b_in */ + + /* P8_34 (ZCZ ball U4) hdmi */ + P8_34_default_pin: pinmux_P8_34_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pin: pinmux_P8_34_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pu_pin: pinmux_P8_34_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pd_pin: pinmux_P8_34_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_input_pin: pinmux_P8_34_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_pwm_pin: pinmux_P8_34_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data11.ehrpwm1b */ + + /* P8_35 (ZCZ ball V2) hdmi */ + P8_35_default_pin: pinmux_P8_35_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pin: pinmux_P8_35_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pu_pin: pinmux_P8_35_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pd_pin: pinmux_P8_35_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_input_pin: pinmux_P8_35_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_qep_pin: pinmux_P8_35_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data12.eqep1a_in */ + + /* P8_36 (ZCZ ball U3) hdmi */ + P8_36_default_pin: pinmux_P8_36_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pin: pinmux_P8_36_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pu_pin: pinmux_P8_36_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pd_pin: pinmux_P8_36_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_input_pin: pinmux_P8_36_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_pwm_pin: pinmux_P8_36_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data10.ehrpwm1a */ + + /* P8_37 (ZCZ ball U1) hdmi */ + P8_37_default_pin: pinmux_P8_37_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pin: pinmux_P8_37_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pu_pin: pinmux_P8_37_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pd_pin: pinmux_P8_37_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_input_pin: pinmux_P8_37_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_pwm_pin: pinmux_P8_37_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data8.ehrpwm1_tripzone_input */ + P8_37_uart_pin: pinmux_P8_37_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data8.uart5_txd */ + + /* P8_38 (ZCZ ball U2) hdmi */ + P8_38_default_pin: pinmux_P8_38_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pin: pinmux_P8_38_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pu_pin: pinmux_P8_38_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pd_pin: pinmux_P8_38_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_input_pin: pinmux_P8_38_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_pwm_pin: pinmux_P8_38_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data9.ehrpwm0_synco */ + P8_38_uart_pin: pinmux_P8_38_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data9.uart5_rxd */ + + /* P8_39 (ZCZ ball T3) hdmi */ + P8_39_default_pin: pinmux_P8_39_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pin: pinmux_P8_39_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pu_pin: pinmux_P8_39_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pd_pin: pinmux_P8_39_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_input_pin: pinmux_P8_39_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_qep_pin: pinmux_P8_39_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data6.eqep2_index */ + P8_39_pruout_pin: pinmux_P8_39_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data6.pru1_out6 */ + P8_39_pruin_pin: pinmux_P8_39_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data6.pru1_in6 */ + + /* P8_40 (ZCZ ball T4) hdmi */ + P8_40_default_pin: pinmux_P8_40_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pin: pinmux_P8_40_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pu_pin: pinmux_P8_40_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pd_pin: pinmux_P8_40_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_input_pin: pinmux_P8_40_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_qep_pin: pinmux_P8_40_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data7.eqep2_strobe */ + P8_40_pruout_pin: pinmux_P8_40_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data7.pru1_out7 */ + P8_40_pruin_pin: pinmux_P8_40_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data7.pru1_in7 */ + + /* P8_41 (ZCZ ball T1) hdmi */ + P8_41_default_pin: pinmux_P8_41_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pin: pinmux_P8_41_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pu_pin: pinmux_P8_41_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pd_pin: pinmux_P8_41_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_input_pin: pinmux_P8_41_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_qep_pin: pinmux_P8_41_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data4.eqep2a_in */ + P8_41_pruout_pin: pinmux_P8_41_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data4.pru1_out4 */ + P8_41_pruin_pin: pinmux_P8_41_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data4.pru1_in4 */ + + /* P8_42 (ZCZ ball T2) hdmi */ + P8_42_default_pin: pinmux_P8_42_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pin: pinmux_P8_42_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pu_pin: pinmux_P8_42_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pd_pin: pinmux_P8_42_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_input_pin: pinmux_P8_42_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_qep_pin: pinmux_P8_42_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data5.eqep2b_in */ + P8_42_pruout_pin: pinmux_P8_42_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data5.pru1_out5 */ + P8_42_pruin_pin: pinmux_P8_42_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data5.pru1_in5 */ + + /* P8_43 (ZCZ ball R3) hdmi */ + P8_43_default_pin: pinmux_P8_43_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pin: pinmux_P8_43_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pu_pin: pinmux_P8_43_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pd_pin: pinmux_P8_43_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_input_pin: pinmux_P8_43_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_pwm_pin: pinmux_P8_43_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data2.ehrpwm2_tripzone_input */ + P8_43_pruout_pin: pinmux_P8_43_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data2.pru1_out2 */ + P8_43_pruin_pin: pinmux_P8_43_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data2.pru1_in2 */ + + /* P8_44 (ZCZ ball R4) hdmi */ + P8_44_default_pin: pinmux_P8_44_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pin: pinmux_P8_44_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pu_pin: pinmux_P8_44_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pd_pin: pinmux_P8_44_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_input_pin: pinmux_P8_44_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_pwm_pin: pinmux_P8_44_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data3.ehrpwm0_synco */ + P8_44_pruout_pin: pinmux_P8_44_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data3.pru1_out3 */ + P8_44_pruin_pin: pinmux_P8_44_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data3.pru1_in3 */ + + /* P8_45 (ZCZ ball R1) hdmi */ + P8_45_default_pin: pinmux_P8_45_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pin: pinmux_P8_45_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pu_pin: pinmux_P8_45_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pd_pin: pinmux_P8_45_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_input_pin: pinmux_P8_45_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_pwm_pin: pinmux_P8_45_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data0.ehrpwm2a */ + P8_45_pruout_pin: pinmux_P8_45_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data0.pru1_out0 */ + P8_45_pruin_pin: pinmux_P8_45_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data0.pru1_in0 */ + + /* P8_46 (ZCZ ball R2) hdmi */ + P8_46_default_pin: pinmux_P8_46_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pin: pinmux_P8_46_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pu_pin: pinmux_P8_46_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pd_pin: pinmux_P8_46_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_input_pin: pinmux_P8_46_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_pwm_pin: pinmux_P8_46_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data1.ehrpwm2b */ + P8_46_pruout_pin: pinmux_P8_46_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data1.pru1_out1 */ + P8_46_pruin_pin: pinmux_P8_46_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data1.pru1_in1 */ + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + + /* P9_02 GND */ + + /* P9_03 3V3 */ + + /* P9_04 3V3 */ + + /* P9_05 VDD_5V */ + + /* P9_06 VDD_5V */ + + /* P9_07 SYS_5V */ + + /* P9_08 SYS_5V */ + + /* P9_09 PWR_BUT */ + + /* P9_10 RSTn */ + + /* P9_11 (ZCZ ball T17) gpio0_30 */ + P9_11_default_pin: pinmux_P9_11_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_input_pin: pinmux_P9_11_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wait0.uart4_rxd */ + + /* P9_12 (ZCZ ball U18) gpio1_28 */ + P9_12_default_pin: pinmux_P9_12_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pin: pinmux_P9_12_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pu_pin: pinmux_P9_12_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pd_pin: pinmux_P9_12_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_input_pin: pinmux_P9_12_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + + /* P9_13 (ZCZ ball U17) gpio0_31 */ + P9_13_default_pin: pinmux_P9_13_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pin: pinmux_P9_13_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pu_pin: pinmux_P9_13_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pd_pin: pinmux_P9_13_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_input_pin: pinmux_P9_13_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_uart_pin: pinmux_P9_13_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wpn.uart4_txd */ + + /* P9_14 (ZCZ ball U14) gpio1_18 */ + P9_14_default_pin: pinmux_P9_14_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pin: pinmux_P9_14_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pu_pin: pinmux_P9_14_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pd_pin: pinmux_P9_14_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_input_pin: pinmux_P9_14_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_pwm_pin: pinmux_P9_14_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a2.ehrpwm1a */ + + /* P9_15 (ZCZ ball R13) gpio1_16 */ + P9_15_default_pin: pinmux_P9_15_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pin: pinmux_P9_15_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pu_pin: pinmux_P9_15_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pd_pin: pinmux_P9_15_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_input_pin: pinmux_P9_15_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_pwm_pin: pinmux_P9_15_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a0.ehrpwm1_tripzone_input */ + + /* P9_16 (ZCZ ball T14) gpio1_19 */ + P9_16_default_pin: pinmux_P9_16_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pin: pinmux_P9_16_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pu_pin: pinmux_P9_16_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pd_pin: pinmux_P9_16_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_input_pin: pinmux_P9_16_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_pwm_pin: pinmux_P9_16_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a3.ehrpwm1b */ + + /* P9_17 (ZCZ ball A16) gpio0_5 */ + P9_17_default_pin: pinmux_P9_17_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pin: pinmux_P9_17_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pu_pin: pinmux_P9_17_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pd_pin: pinmux_P9_17_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_input_pin: pinmux_P9_17_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_INPUT | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_spi_cs_pin: pinmux_P9_17_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_cs0.spi0_cs0 */ + P9_17_i2c_pin: pinmux_P9_17_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_cs0.i2c1_scl */ + P9_17_pwm_pin: pinmux_P9_17_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_cs0.ehrpwm0_synci */ + P9_17_pru_uart_pin: pinmux_P9_17_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_cs0.pr1_uart0_txd */ + + /* P9_18 (ZCZ ball B16) gpio0_4 */ + P9_18_default_pin: pinmux_P9_18_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pin: pinmux_P9_18_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pu_pin: pinmux_P9_18_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pd_pin: pinmux_P9_18_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_input_pin: pinmux_P9_18_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_spi_pin: pinmux_P9_18_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d1.spi0_d1 */ + P9_18_i2c_pin: pinmux_P9_18_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d1.i2c1_sda */ + P9_18_pwm_pin: pinmux_P9_18_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d1.ehrpwm0_tripzone_input */ + P9_18_pru_uart_pin: pinmux_P9_18_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d1.pr1_uart0_rxd */ + + /* P9_19 (ZCZ ball D17) i2c2_scl */ + P9_19_default_pin: pinmux_P9_19_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P9_19_gpio_pin: pinmux_P9_19_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_pu_pin: pinmux_P9_19_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_pd_pin: pinmux_P9_19_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_input_pin: pinmux_P9_19_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_timer_pin: pinmux_P9_19_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart1_rtsn.timer5 */ + P9_19_can_pin: pinmux_P9_19_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rtsn.dcan0_rx */ + P9_19_i2c_pin: pinmux_P9_19_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P9_19_spi_cs_pin: pinmux_P9_19_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_rtsn.spi1_cs1 */ + P9_19_pru_uart_pin: pinmux_P9_19_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rtsn.pr1_uart0_rts_n */ + + /* P9_20 (ZCZ ball D18) i2c2_sda */ + P9_20_default_pin: pinmux_P9_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P9_20_gpio_pin: pinmux_P9_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_pu_pin: pinmux_P9_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_pd_pin: pinmux_P9_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_input_pin: pinmux_P9_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_INPUT | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_timer_pin: pinmux_P9_20_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart1_ctsn.timer6 */ + P9_20_can_pin: pinmux_P9_20_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_ctsn.dcan0_tx */ + P9_20_i2c_pin: pinmux_P9_20_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P9_20_spi_cs_pin: pinmux_P9_20_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_ctsn.spi1_cs0 */ + P9_20_pru_uart_pin: pinmux_P9_20_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_ctsn.pr1_uart0_cts_n */ + + /* P9_21 (ZCZ ball B17) gpio0_3 */ + P9_21_default_pin: pinmux_P9_21_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pin: pinmux_P9_21_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pu_pin: pinmux_P9_21_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pd_pin: pinmux_P9_21_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_input_pin: pinmux_P9_21_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_spi_pin: pinmux_P9_21_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d0.spi0_d0 */ + P9_21_uart_pin: pinmux_P9_21_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_d0.uart2_txd */ + P9_21_i2c_pin: pinmux_P9_21_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d0.i2c2_scl */ + P9_21_pwm_pin: pinmux_P9_21_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d0.ehrpwm0b */ + P9_21_pru_uart_pin: pinmux_P9_21_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d0.pr1_uart0_rts_n */ + + /* P9_22 (ZCZ ball A17) gpio0_2 */ + P9_22_default_pin: pinmux_P9_22_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pin: pinmux_P9_22_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pu_pin: pinmux_P9_22_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pd_pin: pinmux_P9_22_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_input_pin: pinmux_P9_22_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_INPUT | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_spi_sclk_pin: pinmux_P9_22_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_sclk.spi0_sclk */ + P9_22_uart_pin: pinmux_P9_22_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_sclk.uart2_rxd */ + P9_22_i2c_pin: pinmux_P9_22_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_sclk.i2c2_sda */ + P9_22_pwm_pin: pinmux_P9_22_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_sclk.ehrpwm0a */ + P9_22_pru_uart_pin: pinmux_P9_22_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_sclk.pr1_uart0_cts_n */ + + /* P9_23 (ZCZ ball V14) gpio1_17 */ + P9_23_default_pin: pinmux_P9_23_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_input_pin: pinmux_P9_23_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a1.ehrpwm0_synco */ + + /* P9_24 (ZCZ ball D15) gpio0_15 */ + P9_24_default_pin: pinmux_P9_24_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pin: pinmux_P9_24_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pu_pin: pinmux_P9_24_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pd_pin: pinmux_P9_24_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_input_pin: pinmux_P9_24_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_uart_pin: pinmux_P9_24_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_txd.uart1_txd */ + P9_24_can_pin: pinmux_P9_24_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_txd.dcan1_rx */ + P9_24_i2c_pin: pinmux_P9_24_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_txd.i2c1_scl */ + P9_24_pru_uart_pin: pinmux_P9_24_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_txd.pr1_uart0_txd */ + P9_24_pruin_pin: pinmux_P9_24_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE6) >; }; /* uart1_txd.pru0_in16 */ + + /* P9_25 (ZCZ ball A14) audio */ + P9_25_default_pin: pinmux_P9_25_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pin: pinmux_P9_25_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pu_pin: pinmux_P9_25_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pd_pin: pinmux_P9_25_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_input_pin: pinmux_P9_25_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_qep_pin: pinmux_P9_25_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkx.eqep0_strobe */ + P9_25_pruout_pin: pinmux_P9_25_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkx.pru0_out7 */ + P9_25_pruin_pin: pinmux_P9_25_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkx.pru0_in7 */ + + /* P9_26 (ZCZ ball D16) gpio0_14 */ + P9_26_default_pin: pinmux_P9_26_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pin: pinmux_P9_26_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pu_pin: pinmux_P9_26_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pd_pin: pinmux_P9_26_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_input_pin: pinmux_P9_26_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_uart_pin: pinmux_P9_26_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_rxd.uart1_rxd */ + P9_26_can_pin: pinmux_P9_26_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rxd.dcan1_tx */ + P9_26_i2c_pin: pinmux_P9_26_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rxd.i2c1_sda */ + P9_26_pru_uart_pin: pinmux_P9_26_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rxd.pr1_uart0_rxd */ + P9_26_pruin_pin: pinmux_P9_26_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE6) >; }; /* uart1_rxd.pru1_in16 */ + + /* P9_27 (ZCZ ball C13) gpio3_19 */ + P9_27_default_pin: pinmux_P9_27_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pin: pinmux_P9_27_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pu_pin: pinmux_P9_27_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pd_pin: pinmux_P9_27_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_input_pin: pinmux_P9_27_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_qep_pin: pinmux_P9_27_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsr.eqep0b_in */ + P9_27_pruout_pin: pinmux_P9_27_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsr.pru0_out5 */ + P9_27_pruin_pin: pinmux_P9_27_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsr.pru0_in5 */ + + /* P9_28 (ZCZ ball C12) audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_input_pin: pinmux_P9_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkr.ehrpwm0_synci */ + P9_28_spi_cs_pin: pinmux_P9_28_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_ahclkr.spi1_cs0 */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* mcasp0_ahclkr.ecap2_in_pwm2_out */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkr.pru0_out3 */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkr.pru0_in3 */ + + /* P9_29 (ZCZ ball B13) audio */ + P9_29_default_pin: pinmux_P9_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pin: pinmux_P9_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pu_pin: pinmux_P9_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pd_pin: pinmux_P9_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_input_pin: pinmux_P9_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_pwm_pin: pinmux_P9_29_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsx.ehrpwm0b */ + P9_29_spi_pin: pinmux_P9_29_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_fsx.spi1_d0 */ + P9_29_pruout_pin: pinmux_P9_29_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsx.pru0_out1 */ + P9_29_pruin_pin: pinmux_P9_29_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsx.pru0_in1 */ + + /* P9_30 (ZCZ ball D12) gpio3_16 */ + P9_30_default_pin: pinmux_P9_30_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P9_30_gpio_pin: pinmux_P9_30_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P9_30_gpio_pu_pin: pinmux_P9_30_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P9_30_gpio_pd_pin: pinmux_P9_30_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P9_30_gpio_input_pin: pinmux_P9_30_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P9_30_pwm_pin: pinmux_P9_30_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_axr0.ehrpwm0_tripzone_input */ + P9_30_spi_pin: pinmux_P9_30_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_axr0.spi1_d1 */ + P9_30_pruout_pin: pinmux_P9_30_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_axr0.pru0_out2 */ + P9_30_pruin_pin: pinmux_P9_30_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr0.pru0_in2 */ + + /* P9_31 (ZCZ ball A13) audio */ + P9_31_default_pin: pinmux_P9_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pin: pinmux_P9_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pu_pin: pinmux_P9_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pd_pin: pinmux_P9_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_input_pin: pinmux_P9_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_pwm_pin: pinmux_P9_31_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkx.ehrpwm0a */ + P9_31_spi_sclk_pin: pinmux_P9_31_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_aclkx.spi1_sclk */ + P9_31_pruout_pin: pinmux_P9_31_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkx.pru0_out0 */ + P9_31_pruin_pin: pinmux_P9_31_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkx.pru0_in0 */ + + /* P9_32 VADC */ + + /* P9_33 (ZCZ ball C8) AIN4 */ + + /* P9_34 AGND */ + + /* P9_35 (ZCZ ball A8) AIN6 */ + + /* P9_36 (ZCZ ball B8) AIN5 */ + + /* P9_37 (ZCZ ball B7) AIN2 */ + + /* P9_38 (ZCZ ball A7) AIN3 */ + + /* P9_39 (ZCZ ball B6) AIN0 */ + + /* P9_40 (ZCZ ball C7) AIN1 */ + + /* P9_41 (ZCZ ball D14) gpio0_20 */ + P9_41_default_pin: pinmux_P9_41_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pin: pinmux_P9_41_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pu_pin: pinmux_P9_41_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pd_pin: pinmux_P9_41_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_input_pin: pinmux_P9_41_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_timer_pin: pinmux_P9_41_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* xdma_event_intr1.timer7 */ + P9_41_pruin_pin: pinmux_P9_41_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE5) >; }; /* xdma_event_intr1.pru0_in16 */ + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) gpio3_20 */ + P9_91_default_pin: pinmux_P9_91_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pin: pinmux_P9_91_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pu_pin: pinmux_P9_91_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pd_pin: pinmux_P9_91_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_input_pin: pinmux_P9_91_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_qep_pin: pinmux_P9_91_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_axr1.eqep0_index */ + P9_91_pruout_pin: pinmux_P9_91_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_axr1.pru0_out6 */ + P9_91_pruin_pin: pinmux_P9_91_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr1.pru0_in6 */ + + /* P9_42 (ZCZ ball C18) gpio0_7 */ + P9_42_default_pin: pinmux_P9_42_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pin: pinmux_P9_42_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pu_pin: pinmux_P9_42_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pd_pin: pinmux_P9_42_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_input_pin: pinmux_P9_42_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_INPUT | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_pwm_pin: pinmux_P9_42_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE0) >; }; /* eCAP0_in_PWM0_out.ecap0_in_pwm0_out */ + P9_42_uart_pin: pinmux_P9_42_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* eCAP0_in_PWM0_out.uart3_txd */ + P9_42_spi_cs_pin: pinmux_P9_42_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* eCAP0_in_PWM0_out.spi1_cs1 */ + P9_42_pru_ecap_pin: pinmux_P9_42_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* eCAP0_in_PWM0_out.pr1_ecap0_ecap_capin_apwm_o */ + P9_42_spi_sclk_pin: pinmux_P9_42_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* eCAP0_in_PWM0_out.spi1_sclk */ + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) gpio3_18 */ + P9_92_default_pin: pinmux_P9_92_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pin: pinmux_P9_92_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pu_pin: pinmux_P9_92_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pd_pin: pinmux_P9_92_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_input_pin: pinmux_P9_92_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_qep_pin: pinmux_P9_92_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkr.eqep0a_in */ + P9_92_pruout_pin: pinmux_P9_92_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkr.pru0_out4 */ + P9_92_pruin_pin: pinmux_P9_92_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkr.pru0_in4 */ + + /* P9_43 GND */ + + /* P9_44 GND */ + + /* P9_45 GND */ + + /* P9_46 GND */ + + /* (ZCZ ball A15) */ + A15_default_pin: pinmux_A15_default_pin { + pinctrl-single,pins = <0x1b0 (PIN_OUTPUT_PULLUP | MUX_MODE7)>; }; /* Mode 7, Pull-Up */ + A15_clkout_pin: pinmux_A15_clkout_pin { + pinctrl-single,pins = <0x1b0 0x0b>; }; /* Mode 3 */ + A15_gpio_pin: pinmux_A15_gpio_pin { + pinctrl-single,pins = <0x1b0 0x2f>; }; /* Mode 7, RxActive */ + A15_gpio_pu_pin: pinmux_A15_gpio_pu_pin { + pinctrl-single,pins = <0x1b0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + A15_gpio_pd_pin: pinmux_A15_gpio_pd_pin { + pinctrl-single,pins = <0x1b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + clock-frequency = <100000>; + symlink = "bone/i2c/1"; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + clock-frequency = <100000>; + symlink = "bone/i2c/2"; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/1"; +}; + +&uart2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/2"; +}; + +&uart3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/3"; +}; + +&uart4 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/4"; +}; + +&uart5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/5"; +}; + +&dcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/can/0"; +}; + +&dcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/can/1"; +}; + +&eqep0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/0"; +}; + +&eqep1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/1"; +}; + +&eqep2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/2"; +}; + +&epwmss0 { + status = "okay"; +}; + +&epwmss1 { + status = "okay"; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ehrpwm1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ehrpwm2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/0.0"; + + reg = <0>; + spi-max-frequency = <16000000>; + spi-cpha; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/0.1"; + + reg = <1>; + spi-max-frequency = <16000000>; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/1.0"; + + reg = <0>; + spi-max-frequency = <16000000>; + spi-cpha; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/1.1"; + + reg = <1>; + spi-max-frequency = <16000000>; + }; +}; + +/**********************************************************************/ +/* Pin Multiplex Helpers */ +/* */ +/* These provide userspace runtime pin configuration for the */ +/* BeagleBone cape expansion headers */ +/**********************************************************************/ + +&ocp { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + + /* P8_02 GND */ + + + /* P8_03 (ZCZ ball R9) emmc */ + P8_03_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_03_default_pin>; + pinctrl-1 = <&P8_03_gpio_pin>; + pinctrl-2 = <&P8_03_gpio_pu_pin>; + pinctrl-3 = <&P8_03_gpio_pd_pin>; + pinctrl-4 = <&P8_03_gpio_input_pin>; + }; + + /* P8_04 (ZCZ ball T9) emmc */ + P8_04_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_04_default_pin>; + pinctrl-1 = <&P8_04_gpio_pin>; + pinctrl-2 = <&P8_04_gpio_pu_pin>; + pinctrl-3 = <&P8_04_gpio_pd_pin>; + pinctrl-4 = <&P8_04_gpio_input_pin>; + }; + + /* P8_05 (ZCZ ball R8) emmc */ + P8_05_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_05_default_pin>; + pinctrl-1 = <&P8_05_gpio_pin>; + pinctrl-2 = <&P8_05_gpio_pu_pin>; + pinctrl-3 = <&P8_05_gpio_pd_pin>; + pinctrl-4 = <&P8_05_gpio_input_pin>; + }; + + /* P8_06 (ZCZ ball T8) emmc */ + P8_06_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_06_default_pin>; + pinctrl-1 = <&P8_06_gpio_pin>; + pinctrl-2 = <&P8_06_gpio_pu_pin>; + pinctrl-3 = <&P8_06_gpio_pd_pin>; + pinctrl-4 = <&P8_06_gpio_input_pin>; + }; + + /* P8_07 (ZCZ ball R7) */ + P8_07_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_07_default_pin>; + pinctrl-1 = <&P8_07_gpio_pin>; + pinctrl-2 = <&P8_07_gpio_pu_pin>; + pinctrl-3 = <&P8_07_gpio_pd_pin>; + pinctrl-4 = <&P8_07_gpio_input_pin>; + pinctrl-5 = <&P8_07_timer_pin>; + }; + + /* P8_08 (ZCZ ball T7) */ + P8_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_08_default_pin>; + pinctrl-1 = <&P8_08_gpio_pin>; + pinctrl-2 = <&P8_08_gpio_pu_pin>; + pinctrl-3 = <&P8_08_gpio_pd_pin>; + pinctrl-4 = <&P8_08_gpio_input_pin>; + pinctrl-5 = <&P8_08_timer_pin>; + }; + + /* P8_09 (ZCZ ball T6) */ + P8_09_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_09_default_pin>; + pinctrl-1 = <&P8_09_gpio_pin>; + pinctrl-2 = <&P8_09_gpio_pu_pin>; + pinctrl-3 = <&P8_09_gpio_pd_pin>; + pinctrl-4 = <&P8_09_gpio_input_pin>; + pinctrl-5 = <&P8_09_timer_pin>; + }; + + /* P8_10 (ZCZ ball U6) */ + P8_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_10_default_pin>; + pinctrl-1 = <&P8_10_gpio_pin>; + pinctrl-2 = <&P8_10_gpio_pu_pin>; + pinctrl-3 = <&P8_10_gpio_pd_pin>; + pinctrl-4 = <&P8_10_gpio_input_pin>; + pinctrl-5 = <&P8_10_timer_pin>; + }; + + /* P8_11 (ZCZ ball R12) */ + P8_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P8_11_default_pin>; + pinctrl-1 = <&P8_11_gpio_pin>; + pinctrl-2 = <&P8_11_gpio_pu_pin>; + pinctrl-3 = <&P8_11_gpio_pd_pin>; + pinctrl-4 = <&P8_11_gpio_input_pin>; + pinctrl-5 = <&P8_11_qep_pin>; + pinctrl-6 = <&P8_11_pruout_pin>; + }; + + /* P8_12 (ZCZ ball T12) */ + P8_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P8_12_default_pin>; + pinctrl-1 = <&P8_12_gpio_pin>; + pinctrl-2 = <&P8_12_gpio_pu_pin>; + pinctrl-3 = <&P8_12_gpio_pd_pin>; + pinctrl-4 = <&P8_12_gpio_input_pin>; + pinctrl-5 = <&P8_12_qep_pin>; + pinctrl-6 = <&P8_12_pruout_pin>; + }; + + /* P8_13 (ZCZ ball T10) */ + P8_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_13_default_pin>; + pinctrl-1 = <&P8_13_gpio_pin>; + pinctrl-2 = <&P8_13_gpio_pu_pin>; + pinctrl-3 = <&P8_13_gpio_pd_pin>; + pinctrl-4 = <&P8_13_gpio_input_pin>; + pinctrl-5 = <&P8_13_pwm_pin>; + }; + + /* P8_14 (ZCZ ball T11) */ + P8_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_14_default_pin>; + pinctrl-1 = <&P8_14_gpio_pin>; + pinctrl-2 = <&P8_14_gpio_pu_pin>; + pinctrl-3 = <&P8_14_gpio_pd_pin>; + pinctrl-4 = <&P8_14_gpio_input_pin>; + pinctrl-5 = <&P8_14_pwm_pin>; + }; + + /* P8_15 (ZCZ ball U13) */ + P8_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pru_ecap", "pruin"; + pinctrl-0 = <&P8_15_default_pin>; + pinctrl-1 = <&P8_15_gpio_pin>; + pinctrl-2 = <&P8_15_gpio_pu_pin>; + pinctrl-3 = <&P8_15_gpio_pd_pin>; + pinctrl-4 = <&P8_15_gpio_input_pin>; + pinctrl-5 = <&P8_15_qep_pin>; + pinctrl-6 = <&P8_15_pru_ecap_pin>; + pinctrl-7 = <&P8_15_pruin_pin>; + }; + + /* P8_16 (ZCZ ball V13) */ + P8_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruin"; + pinctrl-0 = <&P8_16_default_pin>; + pinctrl-1 = <&P8_16_gpio_pin>; + pinctrl-2 = <&P8_16_gpio_pu_pin>; + pinctrl-3 = <&P8_16_gpio_pd_pin>; + pinctrl-4 = <&P8_16_gpio_input_pin>; + pinctrl-5 = <&P8_16_qep_pin>; + pinctrl-6 = <&P8_16_pruin_pin>; + }; + + /* P8_17 (ZCZ ball U12) */ + P8_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_17_default_pin>; + pinctrl-1 = <&P8_17_gpio_pin>; + pinctrl-2 = <&P8_17_gpio_pu_pin>; + pinctrl-3 = <&P8_17_gpio_pd_pin>; + pinctrl-4 = <&P8_17_gpio_input_pin>; + pinctrl-5 = <&P8_17_pwm_pin>; + }; + + /* P8_18 (ZCZ ball V12) */ + P8_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_18_default_pin>; + pinctrl-1 = <&P8_18_gpio_pin>; + pinctrl-2 = <&P8_18_gpio_pu_pin>; + pinctrl-3 = <&P8_18_gpio_pd_pin>; + pinctrl-4 = <&P8_18_gpio_input_pin>; + }; + + /* P8_19 (ZCZ ball U10) */ + P8_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_19_default_pin>; + pinctrl-1 = <&P8_19_gpio_pin>; + pinctrl-2 = <&P8_19_gpio_pu_pin>; + pinctrl-3 = <&P8_19_gpio_pd_pin>; + pinctrl-4 = <&P8_19_gpio_input_pin>; + pinctrl-5 = <&P8_19_pwm_pin>; + }; + + /* P8_20 (ZCZ ball V9) emmc */ + P8_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_20_default_pin>; + pinctrl-1 = <&P8_20_gpio_pin>; + pinctrl-2 = <&P8_20_gpio_pu_pin>; + pinctrl-3 = <&P8_20_gpio_pd_pin>; + pinctrl-4 = <&P8_20_gpio_input_pin>; + pinctrl-5 = <&P8_20_pruout_pin>; + pinctrl-6 = <&P8_20_pruin_pin>; + }; + + /* P8_21 (ZCZ ball U9) emmc */ + P8_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_21_default_pin>; + pinctrl-1 = <&P8_21_gpio_pin>; + pinctrl-2 = <&P8_21_gpio_pu_pin>; + pinctrl-3 = <&P8_21_gpio_pd_pin>; + pinctrl-4 = <&P8_21_gpio_input_pin>; + pinctrl-5 = <&P8_21_pruout_pin>; + pinctrl-6 = <&P8_21_pruin_pin>; + }; + + /* P8_22 (ZCZ ball V8) emmc */ + P8_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_22_default_pin>; + pinctrl-1 = <&P8_22_gpio_pin>; + pinctrl-2 = <&P8_22_gpio_pu_pin>; + pinctrl-3 = <&P8_22_gpio_pd_pin>; + pinctrl-4 = <&P8_22_gpio_input_pin>; + }; + + /* P8_23 (ZCZ ball U8) emmc */ + P8_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_23_default_pin>; + pinctrl-1 = <&P8_23_gpio_pin>; + pinctrl-2 = <&P8_23_gpio_pu_pin>; + pinctrl-3 = <&P8_23_gpio_pd_pin>; + pinctrl-4 = <&P8_23_gpio_input_pin>; + }; + + /* P8_24 (ZCZ ball V7) emmc */ + P8_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_24_default_pin>; + pinctrl-1 = <&P8_24_gpio_pin>; + pinctrl-2 = <&P8_24_gpio_pu_pin>; + pinctrl-3 = <&P8_24_gpio_pd_pin>; + pinctrl-4 = <&P8_24_gpio_input_pin>; + }; + + /* P8_25 (ZCZ ball U7) emmc */ + P8_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_25_default_pin>; + pinctrl-1 = <&P8_25_gpio_pin>; + pinctrl-2 = <&P8_25_gpio_pu_pin>; + pinctrl-3 = <&P8_25_gpio_pd_pin>; + pinctrl-4 = <&P8_25_gpio_input_pin>; + }; + + /* P8_26 (ZCZ ball V6) */ + P8_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_26_default_pin>; + pinctrl-1 = <&P8_26_gpio_pin>; + pinctrl-2 = <&P8_26_gpio_pu_pin>; + pinctrl-3 = <&P8_26_gpio_pd_pin>; + pinctrl-4 = <&P8_26_gpio_input_pin>; + }; + + /* P8_27 (ZCZ ball U5) hdmi */ + P8_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_27_default_pin>; + pinctrl-1 = <&P8_27_gpio_pin>; + pinctrl-2 = <&P8_27_gpio_pu_pin>; + pinctrl-3 = <&P8_27_gpio_pd_pin>; + pinctrl-4 = <&P8_27_gpio_input_pin>; + pinctrl-5 = <&P8_27_pruout_pin>; + pinctrl-6 = <&P8_27_pruin_pin>; + }; + + /* P8_28 (ZCZ ball V5) hdmi */ + P8_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_28_default_pin>; + pinctrl-1 = <&P8_28_gpio_pin>; + pinctrl-2 = <&P8_28_gpio_pu_pin>; + pinctrl-3 = <&P8_28_gpio_pd_pin>; + pinctrl-4 = <&P8_28_gpio_input_pin>; + pinctrl-5 = <&P8_28_pruout_pin>; + pinctrl-6 = <&P8_28_pruin_pin>; + }; + + /* P8_29 (ZCZ ball R5) hdmi */ + P8_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_29_default_pin>; + pinctrl-1 = <&P8_29_gpio_pin>; + pinctrl-2 = <&P8_29_gpio_pu_pin>; + pinctrl-3 = <&P8_29_gpio_pd_pin>; + pinctrl-4 = <&P8_29_gpio_input_pin>; + pinctrl-5 = <&P8_29_pruout_pin>; + pinctrl-6 = <&P8_29_pruin_pin>; + }; + + /* P8_30 (ZCZ ball R6) hdmi */ + P8_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_30_default_pin>; + pinctrl-1 = <&P8_30_gpio_pin>; + pinctrl-2 = <&P8_30_gpio_pu_pin>; + pinctrl-3 = <&P8_30_gpio_pd_pin>; + pinctrl-4 = <&P8_30_gpio_input_pin>; + pinctrl-5 = <&P8_30_pruout_pin>; + pinctrl-6 = <&P8_30_pruin_pin>; + }; + + /* P8_31 (ZCZ ball V4) hdmi */ + P8_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "qep"; + pinctrl-0 = <&P8_31_default_pin>; + pinctrl-1 = <&P8_31_gpio_pin>; + pinctrl-2 = <&P8_31_gpio_pu_pin>; + pinctrl-3 = <&P8_31_gpio_pd_pin>; + pinctrl-4 = <&P8_31_gpio_input_pin>; + pinctrl-5 = <&P8_31_uart_pin>; + pinctrl-6 = <&P8_31_qep_pin>; + }; + + /* P8_32 (ZCZ ball T5) hdmi */ + P8_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_32_default_pin>; + pinctrl-1 = <&P8_32_gpio_pin>; + pinctrl-2 = <&P8_32_gpio_pu_pin>; + pinctrl-3 = <&P8_32_gpio_pd_pin>; + pinctrl-4 = <&P8_32_gpio_input_pin>; + pinctrl-5 = <&P8_32_qep_pin>; + }; + + /* P8_33 (ZCZ ball V3) hdmi */ + P8_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_33_default_pin>; + pinctrl-1 = <&P8_33_gpio_pin>; + pinctrl-2 = <&P8_33_gpio_pu_pin>; + pinctrl-3 = <&P8_33_gpio_pd_pin>; + pinctrl-4 = <&P8_33_gpio_input_pin>; + pinctrl-5 = <&P8_33_qep_pin>; + }; + + /* P8_34 (ZCZ ball U4) hdmi */ + P8_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_34_default_pin>; + pinctrl-1 = <&P8_34_gpio_pin>; + pinctrl-2 = <&P8_34_gpio_pu_pin>; + pinctrl-3 = <&P8_34_gpio_pd_pin>; + pinctrl-4 = <&P8_34_gpio_input_pin>; + pinctrl-5 = <&P8_34_pwm_pin>; + }; + + /* P8_35 (ZCZ ball V2) hdmi */ + P8_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_35_default_pin>; + pinctrl-1 = <&P8_35_gpio_pin>; + pinctrl-2 = <&P8_35_gpio_pu_pin>; + pinctrl-3 = <&P8_35_gpio_pd_pin>; + pinctrl-4 = <&P8_35_gpio_input_pin>; + pinctrl-5 = <&P8_35_qep_pin>; + }; + + /* P8_36 (ZCZ ball U3) hdmi */ + P8_36_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_36_default_pin>; + pinctrl-1 = <&P8_36_gpio_pin>; + pinctrl-2 = <&P8_36_gpio_pu_pin>; + pinctrl-3 = <&P8_36_gpio_pd_pin>; + pinctrl-4 = <&P8_36_gpio_input_pin>; + pinctrl-5 = <&P8_36_pwm_pin>; + }; + + /* P8_37 (ZCZ ball U1) hdmi */ + P8_37_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "pwm"; + pinctrl-0 = <&P8_37_default_pin>; + pinctrl-1 = <&P8_37_gpio_pin>; + pinctrl-2 = <&P8_37_gpio_pu_pin>; + pinctrl-3 = <&P8_37_gpio_pd_pin>; + pinctrl-4 = <&P8_37_gpio_input_pin>; + pinctrl-5 = <&P8_37_uart_pin>; + pinctrl-6 = <&P8_37_pwm_pin>; + }; + + /* P8_38 (ZCZ ball U2) hdmi */ + P8_38_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "pwm"; + pinctrl-0 = <&P8_38_default_pin>; + pinctrl-1 = <&P8_38_gpio_pin>; + pinctrl-2 = <&P8_38_gpio_pu_pin>; + pinctrl-3 = <&P8_38_gpio_pd_pin>; + pinctrl-4 = <&P8_38_gpio_input_pin>; + pinctrl-5 = <&P8_38_uart_pin>; + pinctrl-6 = <&P8_38_pwm_pin>; + }; + + /* P8_39 (ZCZ ball T3) hdmi */ + P8_39_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_39_default_pin>; + pinctrl-1 = <&P8_39_gpio_pin>; + pinctrl-2 = <&P8_39_gpio_pu_pin>; + pinctrl-3 = <&P8_39_gpio_pd_pin>; + pinctrl-4 = <&P8_39_gpio_input_pin>; + pinctrl-5 = <&P8_39_qep_pin>; + pinctrl-6 = <&P8_39_pruout_pin>; + pinctrl-7 = <&P8_39_pruin_pin>; + }; + + /* P8_40 (ZCZ ball T4) hdmi */ + P8_40_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_40_default_pin>; + pinctrl-1 = <&P8_40_gpio_pin>; + pinctrl-2 = <&P8_40_gpio_pu_pin>; + pinctrl-3 = <&P8_40_gpio_pd_pin>; + pinctrl-4 = <&P8_40_gpio_input_pin>; + pinctrl-5 = <&P8_40_qep_pin>; + pinctrl-6 = <&P8_40_pruout_pin>; + pinctrl-7 = <&P8_40_pruin_pin>; + }; + + /* P8_41 (ZCZ ball T1) hdmi */ + P8_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_41_default_pin>; + pinctrl-1 = <&P8_41_gpio_pin>; + pinctrl-2 = <&P8_41_gpio_pu_pin>; + pinctrl-3 = <&P8_41_gpio_pd_pin>; + pinctrl-4 = <&P8_41_gpio_input_pin>; + pinctrl-5 = <&P8_41_qep_pin>; + pinctrl-6 = <&P8_41_pruout_pin>; + pinctrl-7 = <&P8_41_pruin_pin>; + }; + + /* P8_42 (ZCZ ball T2) hdmi */ + P8_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_42_default_pin>; + pinctrl-1 = <&P8_42_gpio_pin>; + pinctrl-2 = <&P8_42_gpio_pu_pin>; + pinctrl-3 = <&P8_42_gpio_pd_pin>; + pinctrl-4 = <&P8_42_gpio_input_pin>; + pinctrl-5 = <&P8_42_qep_pin>; + pinctrl-6 = <&P8_42_pruout_pin>; + pinctrl-7 = <&P8_42_pruin_pin>; + }; + + /* P8_43 (ZCZ ball R3) hdmi */ + P8_43_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_43_default_pin>; + pinctrl-1 = <&P8_43_gpio_pin>; + pinctrl-2 = <&P8_43_gpio_pu_pin>; + pinctrl-3 = <&P8_43_gpio_pd_pin>; + pinctrl-4 = <&P8_43_gpio_input_pin>; + pinctrl-5 = <&P8_43_pwm_pin>; + pinctrl-6 = <&P8_43_pruout_pin>; + pinctrl-7 = <&P8_43_pruin_pin>; + }; + + /* P8_44 (ZCZ ball R4) hdmi */ + P8_44_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_44_default_pin>; + pinctrl-1 = <&P8_44_gpio_pin>; + pinctrl-2 = <&P8_44_gpio_pu_pin>; + pinctrl-3 = <&P8_44_gpio_pd_pin>; + pinctrl-4 = <&P8_44_gpio_input_pin>; + pinctrl-5 = <&P8_44_pwm_pin>; + pinctrl-6 = <&P8_44_pruout_pin>; + pinctrl-7 = <&P8_44_pruin_pin>; + }; + + /* P8_45 (ZCZ ball R1) hdmi */ + P8_45_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_45_default_pin>; + pinctrl-1 = <&P8_45_gpio_pin>; + pinctrl-2 = <&P8_45_gpio_pu_pin>; + pinctrl-3 = <&P8_45_gpio_pd_pin>; + pinctrl-4 = <&P8_45_gpio_input_pin>; + pinctrl-5 = <&P8_45_pwm_pin>; + pinctrl-6 = <&P8_45_pruout_pin>; + pinctrl-7 = <&P8_45_pruin_pin>; + }; + + /* P8_46 (ZCZ ball R2) hdmi */ + P8_46_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_46_default_pin>; + pinctrl-1 = <&P8_46_gpio_pin>; + pinctrl-2 = <&P8_46_gpio_pu_pin>; + pinctrl-3 = <&P8_46_gpio_pd_pin>; + pinctrl-4 = <&P8_46_gpio_input_pin>; + pinctrl-5 = <&P8_46_pwm_pin>; + pinctrl-6 = <&P8_46_pruout_pin>; + pinctrl-7 = <&P8_46_pruin_pin>; + }; + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + + /* P9_02 GND */ + + /* P9_03 3V3 */ + + /* P9_04 3V3 */ + + /* P9_05 VDD_5V */ + + /* P9_06 VDD_5V */ + + /* P9_07 SYS_5V */ + + /* P9_08 SYS_5V */ + + /* P9_09 PWR_BUT */ + + /* P9_10 RSTn */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P9_11_default_pin>; + pinctrl-1 = <&P9_11_gpio_pin>; + pinctrl-2 = <&P9_11_gpio_pu_pin>; + pinctrl-3 = <&P9_11_gpio_pd_pin>; + pinctrl-4 = <&P9_11_gpio_input_pin>; + pinctrl-5 = <&P9_11_uart_pin>; + }; + + /* P9_12 (ZCZ ball U18) */ + P9_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P9_12_default_pin>; + pinctrl-1 = <&P9_12_gpio_pin>; + pinctrl-2 = <&P9_12_gpio_pu_pin>; + pinctrl-3 = <&P9_12_gpio_pd_pin>; + pinctrl-4 = <&P9_12_gpio_input_pin>; + }; + + /* P9_13 (ZCZ ball U17) */ + P9_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P9_13_default_pin>; + pinctrl-1 = <&P9_13_gpio_pin>; + pinctrl-2 = <&P9_13_gpio_pu_pin>; + pinctrl-3 = <&P9_13_gpio_pd_pin>; + pinctrl-4 = <&P9_13_gpio_input_pin>; + pinctrl-5 = <&P9_13_uart_pin>; + }; + + /* P9_14 (ZCZ ball U14) */ + P9_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_14_default_pin>; + pinctrl-1 = <&P9_14_gpio_pin>; + pinctrl-2 = <&P9_14_gpio_pu_pin>; + pinctrl-3 = <&P9_14_gpio_pd_pin>; + pinctrl-4 = <&P9_14_gpio_input_pin>; + pinctrl-5 = <&P9_14_pwm_pin>; + }; + + /* P9_15 (ZCZ ball R13) */ + P9_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_15_default_pin>; + pinctrl-1 = <&P9_15_gpio_pin>; + pinctrl-2 = <&P9_15_gpio_pu_pin>; + pinctrl-3 = <&P9_15_gpio_pd_pin>; + pinctrl-4 = <&P9_15_gpio_input_pin>; + pinctrl-5 = <&P9_15_pwm_pin>; + }; + + /* P9_16 (ZCZ ball T14) */ + P9_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_16_default_pin>; + pinctrl-1 = <&P9_16_gpio_pin>; + pinctrl-2 = <&P9_16_gpio_pu_pin>; + pinctrl-3 = <&P9_16_gpio_pd_pin>; + pinctrl-4 = <&P9_16_gpio_input_pin>; + pinctrl-5 = <&P9_16_pwm_pin>; + }; + + /* P9_17 (ZCZ ball A16) */ + P9_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_17_default_pin>; + pinctrl-1 = <&P9_17_gpio_pin>; + pinctrl-2 = <&P9_17_gpio_pu_pin>; + pinctrl-3 = <&P9_17_gpio_pd_pin>; + pinctrl-4 = <&P9_17_gpio_input_pin>; + pinctrl-5 = <&P9_17_spi_cs_pin>; + pinctrl-6 = <&P9_17_i2c_pin>; + pinctrl-7 = <&P9_17_pwm_pin>; + pinctrl-8 = <&P9_17_pru_uart_pin>; + }; + + /* P9_18 (ZCZ ball B16) */ + P9_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_18_default_pin>; + pinctrl-1 = <&P9_18_gpio_pin>; + pinctrl-2 = <&P9_18_gpio_pu_pin>; + pinctrl-3 = <&P9_18_gpio_pd_pin>; + pinctrl-4 = <&P9_18_gpio_input_pin>; + pinctrl-5 = <&P9_18_spi_pin>; + pinctrl-6 = <&P9_18_i2c_pin>; + pinctrl-7 = <&P9_18_pwm_pin>; + pinctrl-8 = <&P9_18_pru_uart_pin>; + }; + + /* P9_19 (ZCZ ball D17) i2c */ + P9_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart", "timer"; + pinctrl-0 = <&P9_19_default_pin>; + pinctrl-1 = <&P9_19_gpio_pin>; + pinctrl-2 = <&P9_19_gpio_pu_pin>; + pinctrl-3 = <&P9_19_gpio_pd_pin>; + pinctrl-4 = <&P9_19_gpio_input_pin>; + pinctrl-5 = <&P9_19_spi_cs_pin>; + pinctrl-6 = <&P9_19_can_pin>; + pinctrl-7 = <&P9_19_i2c_pin>; + pinctrl-8 = <&P9_19_pru_uart_pin>; + pinctrl-9 = <&P9_19_timer_pin>; + }; + + /* P9_20 (ZCZ ball D18) i2c */ + P9_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart", "timer"; + pinctrl-0 = <&P9_20_default_pin>; + pinctrl-1 = <&P9_20_gpio_pin>; + pinctrl-2 = <&P9_20_gpio_pu_pin>; + pinctrl-3 = <&P9_20_gpio_pd_pin>; + pinctrl-4 = <&P9_20_gpio_input_pin>; + pinctrl-5 = <&P9_20_spi_cs_pin>; + pinctrl-6 = <&P9_20_can_pin>; + pinctrl-7 = <&P9_20_i2c_pin>; + pinctrl-8 = <&P9_20_pru_uart_pin>; + pinctrl-9 = <&P9_20_timer_pin>; + }; + + /* P9_21 (ZCZ ball B17) */ + P9_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_21_default_pin>; + pinctrl-1 = <&P9_21_gpio_pin>; + pinctrl-2 = <&P9_21_gpio_pu_pin>; + pinctrl-3 = <&P9_21_gpio_pd_pin>; + pinctrl-4 = <&P9_21_gpio_input_pin>; + pinctrl-5 = <&P9_21_spi_pin>; + pinctrl-6 = <&P9_21_uart_pin>; + pinctrl-7 = <&P9_21_i2c_pin>; + pinctrl-8 = <&P9_21_pwm_pin>; + pinctrl-9 = <&P9_21_pru_uart_pin>; + }; + + /* P9_22 (ZCZ ball A17) */ + P9_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_22_default_pin>; + pinctrl-1 = <&P9_22_gpio_pin>; + pinctrl-2 = <&P9_22_gpio_pu_pin>; + pinctrl-3 = <&P9_22_gpio_pd_pin>; + pinctrl-4 = <&P9_22_gpio_input_pin>; + pinctrl-5 = <&P9_22_spi_sclk_pin>; + pinctrl-6 = <&P9_22_uart_pin>; + pinctrl-7 = <&P9_22_i2c_pin>; + pinctrl-8 = <&P9_22_pwm_pin>; + pinctrl-9 = <&P9_22_pru_uart_pin>; + }; + + /* P9_23 (ZCZ ball V14) */ + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_gpio_input_pin>; + pinctrl-5 = <&P9_23_pwm_pin>; + }; + + /* P9_24 (ZCZ ball D15) */ + P9_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P9_24_default_pin>; + pinctrl-1 = <&P9_24_gpio_pin>; + pinctrl-2 = <&P9_24_gpio_pu_pin>; + pinctrl-3 = <&P9_24_gpio_pd_pin>; + pinctrl-4 = <&P9_24_gpio_input_pin>; + pinctrl-5 = <&P9_24_uart_pin>; + pinctrl-6 = <&P9_24_can_pin>; + pinctrl-7 = <&P9_24_i2c_pin>; + pinctrl-8 = <&P9_24_pru_uart_pin>; + pinctrl-9 = <&P9_24_pruin_pin>; + }; + + /* P9_25 (ZCZ ball A14) audio */ + P9_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_25_default_pin>; + pinctrl-1 = <&P9_25_gpio_pin>; + pinctrl-2 = <&P9_25_gpio_pu_pin>; + pinctrl-3 = <&P9_25_gpio_pd_pin>; + pinctrl-4 = <&P9_25_gpio_input_pin>; + pinctrl-5 = <&P9_25_qep_pin>; + pinctrl-6 = <&P9_25_pruout_pin>; + pinctrl-7 = <&P9_25_pruin_pin>; + }; + + /* P9_26 (ZCZ ball D16) */ + P9_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P9_26_default_pin>; + pinctrl-1 = <&P9_26_gpio_pin>; + pinctrl-2 = <&P9_26_gpio_pu_pin>; + pinctrl-3 = <&P9_26_gpio_pd_pin>; + pinctrl-4 = <&P9_26_gpio_input_pin>; + pinctrl-5 = <&P9_26_uart_pin>; + pinctrl-6 = <&P9_26_can_pin>; + pinctrl-7 = <&P9_26_i2c_pin>; + pinctrl-8 = <&P9_26_pru_uart_pin>; + pinctrl-9 = <&P9_26_pruin_pin>; + }; + + /* P9_27 (ZCZ ball C13) */ + P9_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_27_default_pin>; + pinctrl-1 = <&P9_27_gpio_pin>; + pinctrl-2 = <&P9_27_gpio_pu_pin>; + pinctrl-3 = <&P9_27_gpio_pd_pin>; + pinctrl-4 = <&P9_27_gpio_input_pin>; + pinctrl-5 = <&P9_27_qep_pin>; + pinctrl-6 = <&P9_27_pruout_pin>; + pinctrl-7 = <&P9_27_pruin_pin>; + }; + + /* P9_28 (ZCZ ball C12) audio */ + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "pwm", "pwm2", "pruout", "pruin"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_gpio_input_pin>; + pinctrl-5 = <&P9_28_spi_cs_pin>; + pinctrl-6 = <&P9_28_pwm_pin>; + pinctrl-7 = <&P9_28_pwm2_pin>; + pinctrl-8 = <&P9_28_pruout_pin>; + pinctrl-9 = <&P9_28_pruin_pin>; + }; + + /* P9_29 (ZCZ ball B13) audio */ + P9_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P9_29_default_pin>; + pinctrl-1 = <&P9_29_gpio_pin>; + pinctrl-2 = <&P9_29_gpio_pu_pin>; + pinctrl-3 = <&P9_29_gpio_pd_pin>; + pinctrl-4 = <&P9_29_gpio_input_pin>; + pinctrl-5 = <&P9_29_spi_pin>; + pinctrl-6 = <&P9_29_pwm_pin>; + pinctrl-7 = <&P9_29_pruout_pin>; + pinctrl-8 = <&P9_29_pruin_pin>; + }; + + /* P9_30 (ZCZ ball D12) */ + P9_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P9_30_default_pin>; + pinctrl-1 = <&P9_30_gpio_pin>; + pinctrl-2 = <&P9_30_gpio_pu_pin>; + pinctrl-3 = <&P9_30_gpio_pd_pin>; + pinctrl-4 = <&P9_30_gpio_input_pin>; + pinctrl-5 = <&P9_30_spi_pin>; + pinctrl-6 = <&P9_30_pwm_pin>; + pinctrl-7 = <&P9_30_pruout_pin>; + pinctrl-8 = <&P9_30_pruin_pin>; + }; + + /* P9_31 (ZCZ ball A13) audio */ + P9_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P9_31_default_pin>; + pinctrl-1 = <&P9_31_gpio_pin>; + pinctrl-2 = <&P9_31_gpio_pu_pin>; + pinctrl-3 = <&P9_31_gpio_pd_pin>; + pinctrl-4 = <&P9_31_gpio_input_pin>; + pinctrl-5 = <&P9_31_spi_sclk_pin>; + pinctrl-6 = <&P9_31_pwm_pin>; + pinctrl-7 = <&P9_31_pruout_pin>; + pinctrl-8 = <&P9_31_pruin_pin>; + }; + + /* P9_32 VADC */ + + /* P9_33 (ZCZ ball C8) AIN4 */ + + /* P9_34 AGND */ + + /* P9_35 (ZCZ ball A8) AIN6 */ + + /* P9_36 (ZCZ ball B8) AIN5 */ + + /* P9_37 (ZCZ ball B7) AIN2 */ + + /* P9_38 (ZCZ ball A7) AIN3 */ + + /* P9_39 (ZCZ ball B6) AIN0 */ + + /* P9_40 (ZCZ ball C7) AIN1 */ + + /* P9_41 (ZCZ ball D14) */ + P9_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer", "pruin"; + pinctrl-0 = <&P9_41_default_pin>; + pinctrl-1 = <&P9_41_gpio_pin>; + pinctrl-2 = <&P9_41_gpio_pu_pin>; + pinctrl-3 = <&P9_41_gpio_pd_pin>; + pinctrl-4 = <&P9_41_gpio_input_pin>; + pinctrl-5 = <&P9_41_timer_pin>; + pinctrl-6 = <&P9_41_pruin_pin>; + }; + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) */ + P9_91_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_91_default_pin>; + pinctrl-1 = <&P9_91_gpio_pin>; + pinctrl-2 = <&P9_91_gpio_pu_pin>; + pinctrl-3 = <&P9_91_gpio_pd_pin>; + pinctrl-4 = <&P9_91_gpio_input_pin>; + pinctrl-5 = <&P9_91_qep_pin>; + pinctrl-6 = <&P9_91_pruout_pin>; + pinctrl-7 = <&P9_91_pruin_pin>; + }; + + /* P9_42 (ZCZ ball C18) */ + P9_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "spi_sclk", "uart", "pwm", "pru_ecap"; + pinctrl-0 = <&P9_42_default_pin>; + pinctrl-1 = <&P9_42_gpio_pin>; + pinctrl-2 = <&P9_42_gpio_pu_pin>; + pinctrl-3 = <&P9_42_gpio_pd_pin>; + pinctrl-4 = <&P9_42_gpio_input_pin>; + pinctrl-5 = <&P9_42_spi_cs_pin>; + pinctrl-6 = <&P9_42_spi_sclk_pin>; + pinctrl-7 = <&P9_42_uart_pin>; + pinctrl-8 = <&P9_42_pwm_pin>; + pinctrl-9 = <&P9_42_pru_ecap_pin>; + }; + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) */ + P9_92_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_92_default_pin>; + pinctrl-1 = <&P9_92_gpio_pin>; + pinctrl-2 = <&P9_92_gpio_pu_pin>; + pinctrl-3 = <&P9_92_gpio_pd_pin>; + pinctrl-4 = <&P9_92_gpio_input_pin>; + pinctrl-5 = <&P9_92_qep_pin>; + pinctrl-6 = <&P9_92_pruout_pin>; + pinctrl-7 = <&P9_92_pruin_pin>; + }; + + /* P9_43 GND */ + + /* P9_44 GND */ + + /* P9_45 GND */ + + /* P9_46 GND */ + + /* (ZCZ ball A15) */ + A15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "clkout", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&A15_default_pin>; + pinctrl-1 = <&A15_clkout_pin>; + pinctrl-2 = <&A15_gpio_pin>; + pinctrl-3 = <&A15_gpio_pu_pin>; + pinctrl-4 = <&A15_gpio_pd_pin>; + }; + + cape-universal { + compatible = "gpio-of-helper"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + P8_03 { + gpio-name = "P8_03"; + gpio = <&gpio1 6 0>; + input; + dir-changeable; + }; + + P8_04 { + gpio-name = "P8_04"; + gpio = <&gpio1 7 0>; + input; + dir-changeable; + }; + + P8_05 { + gpio-name = "P8_05"; + gpio = <&gpio1 2 0>; + input; + dir-changeable; + }; + + P8_06 { + gpio-name = "P8_06"; + gpio = <&gpio1 3 0>; + input; + dir-changeable; + }; + + P8_07 { + gpio-name = "P8_07"; + gpio = <&gpio2 2 0>; + input; + dir-changeable; + }; + + P8_08 { + gpio-name = "P8_08"; + gpio = <&gpio2 3 0>; + input; + dir-changeable; + }; + + P8_09 { + gpio-name = "P8_09"; + gpio = <&gpio2 5 0>; + input; + dir-changeable; + }; + + P8_10 { + gpio-name = "P8_10"; + gpio = <&gpio2 4 0>; + input; + dir-changeable; + }; + + P8_11 { + gpio-name = "P8_11"; + gpio = <&gpio1 13 0>; + input; + dir-changeable; + }; + + P8_12 { + gpio-name = "P8_12"; + gpio = <&gpio1 12 0>; + input; + dir-changeable; + }; + + P8_13 { + gpio-name = "P8_13"; + gpio = <&gpio0 23 0>; + input; + dir-changeable; + }; + + P8_14 { + gpio-name = "P8_14"; + gpio = <&gpio0 26 0>; + input; + dir-changeable; + }; + + P8_15 { + gpio-name = "P8_15"; + gpio = <&gpio1 15 0>; + input; + dir-changeable; + }; + + P8_16 { + gpio-name = "P8_16"; + gpio = <&gpio1 14 0>; + input; + dir-changeable; + }; + + P8_17 { + gpio-name = "P8_17"; + gpio = <&gpio0 27 0>; + input; + dir-changeable; + }; + + P8_18 { + gpio-name = "P8_18"; + gpio = <&gpio2 1 0>; + input; + dir-changeable; + }; + + P8_19 { + gpio-name = "P8_19"; + gpio = <&gpio0 22 0>; + input; + dir-changeable; + }; + + P8_20 { + gpio-name = "P8_20"; + gpio = <&gpio1 31 0>; + input; + dir-changeable; + }; + + P8_21 { + gpio-name = "P8_21"; + gpio = <&gpio1 30 0>; + input; + dir-changeable; + }; + + P8_22 { + gpio-name = "P8_22"; + gpio = <&gpio1 5 0>; + input; + dir-changeable; + }; + + P8_23 { + gpio-name = "P8_23"; + gpio = <&gpio1 4 0>; + input; + dir-changeable; + }; + + P8_24 { + gpio-name = "P8_24"; + gpio = <&gpio1 1 0>; + input; + dir-changeable; + }; + + P8_25 { + gpio-name = "P8_25"; + gpio = <&gpio1 0 0>; + input; + dir-changeable; + }; + + P8_26 { + gpio-name = "P8_26"; + gpio = <&gpio1 29 0>; + input; + dir-changeable; + }; + + P8_27 { + gpio-name = "P8_27"; + gpio = <&gpio2 22 0>; + input; + dir-changeable; + }; + + P8_28 { + gpio-name = "P8_28"; + gpio = <&gpio2 24 0>; + input; + dir-changeable; + }; + + P8_29 { + gpio-name = "P8_29"; + gpio = <&gpio2 23 0>; + input; + dir-changeable; + }; + + P8_30 { + gpio-name = "P8_30"; + gpio = <&gpio2 25 0>; + input; + dir-changeable; + }; + + P8_31 { + gpio-name = "P8_31"; + gpio = <&gpio0 10 0>; + input; + dir-changeable; + }; + + P8_32 { + gpio-name = "P8_32"; + gpio = <&gpio0 11 0>; + input; + dir-changeable; + }; + + P8_33 { + gpio-name = "P8_33"; + gpio = <&gpio0 9 0>; + input; + dir-changeable; + }; + + P8_34 { + gpio-name = "P8_34"; + gpio = <&gpio2 17 0>; + input; + dir-changeable; + }; + + P8_35 { + gpio-name = "P8_35"; + gpio = <&gpio0 8 0>; + input; + dir-changeable; + }; + + P8_36 { + gpio-name = "P8_36"; + gpio = <&gpio2 16 0>; + input; + dir-changeable; + }; + + P8_37 { + gpio-name = "P8_37"; + gpio = <&gpio2 14 0>; + input; + dir-changeable; + }; + + P8_38 { + gpio-name = "P8_38"; + gpio = <&gpio2 15 0>; + input; + dir-changeable; + }; + + P8_39 { + gpio-name = "P8_39"; + gpio = <&gpio2 12 0>; + input; + dir-changeable; + }; + + P8_40 { + gpio-name = "P8_40"; + gpio = <&gpio2 13 0>; + input; + dir-changeable; + }; + + P8_41 { + gpio-name = "P8_41"; + gpio = <&gpio2 10 0>; + input; + dir-changeable; + }; + + P8_42 { + gpio-name = "P8_42"; + gpio = <&gpio2 11 0>; + input; + dir-changeable; + }; + + P8_43 { + gpio-name = "P8_43"; + gpio = <&gpio2 8 0>; + input; + dir-changeable; + }; + + P8_44 { + gpio-name = "P8_44"; + gpio = <&gpio2 9 0>; + input; + dir-changeable; + }; + + P8_45 { + gpio-name = "P8_45"; + gpio = <&gpio2 6 0>; + input; + dir-changeable; + }; + + P8_46 { + gpio-name = "P8_46"; + gpio = <&gpio2 7 0>; + input; + dir-changeable; + }; + + P9_11 { + gpio-name = "P9_11"; + gpio = <&gpio0 30 0>; + input; + dir-changeable; + }; + + P9_12 { + gpio-name = "P9_12"; + gpio = <&gpio1 28 0>; + input; + dir-changeable; + }; + + P9_13 { + gpio-name = "P9_13"; + gpio = <&gpio0 31 0>; + input; + dir-changeable; + }; + + P9_14 { + gpio-name = "P9_14"; + gpio = <&gpio1 18 0>; + input; + dir-changeable; + }; + + P9_15 { + gpio-name = "P9_15"; + gpio = <&gpio1 16 0>; + input; + dir-changeable; + }; + + P9_16 { + gpio-name = "P9_16"; + gpio = <&gpio1 19 0>; + input; + dir-changeable; + }; + + P9_17 { + gpio-name = "P9_17"; + gpio = <&gpio0 5 0>; + input; + dir-changeable; + }; + + P9_18 { + gpio-name = "P9_18"; + gpio = <&gpio0 4 0>; + input; + dir-changeable; + }; + + P9_19 { + gpio-name = "P9_19"; + gpio = <&gpio0 13 0>; + input; + dir-changeable; + }; + + P9_20 { + gpio-name = "P9_20"; + gpio = <&gpio0 12 0>; + input; + dir-changeable; + }; + + P9_21 { + gpio-name = "P9_21"; + gpio = <&gpio0 3 0>; + input; + dir-changeable; + }; + + P9_22 { + gpio-name = "P9_22"; + gpio = <&gpio0 2 0>; + input; + dir-changeable; + }; + + P9_23 { + gpio-name = "P9_23"; + gpio = <&gpio1 17 0>; + input; + dir-changeable; + }; + + P9_24 { + gpio-name = "P9_24"; + gpio = <&gpio0 15 0>; + input; + dir-changeable; + }; + + P9_25 { + gpio-name = "P9_25"; + gpio = <&gpio3 21 0>; + input; + dir-changeable; + }; + + P9_26 { + gpio-name = "P9_26"; + gpio = <&gpio0 14 0>; + input; + dir-changeable; + }; + + P9_27 { + gpio-name = "P9_27"; + gpio = <&gpio3 19 0>; + input; + dir-changeable; + }; + + P9_28 { + gpio-name = "P9_28"; + gpio = <&gpio3 17 0>; + input; + dir-changeable; + }; + + P9_29 { + gpio-name = "P9_29"; + gpio = <&gpio3 15 0>; + input; + dir-changeable; + }; + + P9_30 { + gpio-name = "P9_30"; + gpio = <&gpio3 16 0>; + input; + dir-changeable; + }; + + P9_31 { + gpio-name = "P9_31"; + gpio = <&gpio3 14 0>; + input; + dir-changeable; + }; + + P9_41 { + gpio-name = "P9_41"; + gpio = <&gpio0 20 0>; + input; + dir-changeable; + }; + + P9_91 { + gpio-name = "P9_91"; + gpio = <&gpio3 20 0>; + input; + dir-changeable; + }; + + P9_42 { + gpio-name = "P9_42"; + gpio = <&gpio0 7 0>; + input; + dir-changeable; + }; + + P9_92 { + gpio-name = "P9_92"; + gpio = <&gpio3 18 0>; + input; + dir-changeable; + }; + + A15 { + gpio-name = "A15"; + gpio = <&gpio0 19 0>; + input; + dir-changeable; + }; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 89b4cf2..914f23b 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -26,14 +26,14 @@ compatible = "gpio-leds"; led2 { - label = "beaglebone:green:heartbeat"; + label = "beaglebone:green:usr0"; gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; default-state = "off"; }; led3 { - label = "beaglebone:green:mmc0"; + label = "beaglebone:green:usr1"; gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; default-state = "off"; @@ -63,9 +63,6 @@ }; &am33xx_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - user_leds_s0: user_leds_s0 { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a5.gpio1_21 */ @@ -96,12 +93,6 @@ >; }; - clkout2_pin: pinmux_clkout2_pin { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ @@ -418,4 +409,5 @@ &rtc { clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>; clock-names = "ext-clk", "int-clk"; + system-power-controller; }; diff --git b/arch/arm/boot/dts/am335x-bone-jtag.dtsi b/arch/arm/boot/dts/am335x-bone-jtag.dtsi new file mode 100644 index 0000000..2cdca01 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-jtag.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2015 Robert Nelson + */ + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&clkout2_pin>; + + clkout2_pin: pinmux_clkout2_pin { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ + >; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bone-uboot-univ.dts b/arch/arm/boot/dts/am335x-bone-uboot-univ.dts new file mode 100644 index 0000000..8755916 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone-uboot-univ.dts @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bone-common-univ.dtsi" + +/ { + model = "TI AM335x BeagleBone"; + compatible = "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bone-uboot-univ.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&ldo3_reg>; +}; diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts index 43bfbce..c7ae3e5 100644 --- a/arch/arm/boot/dts/am335x-bone.dts +++ b/arch/arm/boot/dts/am335x-bone.dts @@ -6,10 +6,16 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone"; compatible = "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bone.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &ldo3_reg { diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi index 91f93bc..94f4b6d 100644 --- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi +++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi @@ -27,7 +27,6 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins { pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) @@ -51,12 +50,6 @@ >; }; - nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) - >; - }; - mcasp0_pins: mcasp0_pins { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */ @@ -92,9 +85,8 @@ nxp,calib-gpios = <&gpio1 25 0>; interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>; - pinctrl-names = "default", "off"; + pinctrl-names = "default"; pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ /* video-ports = <0x234501>; */ diff --git b/arch/arm/boot/dts/am335x-boneblack-uboot-univ.dts b/arch/arm/boot/dts/am335x-boneblack-uboot-univ.dts new file mode 100644 index 0000000..4e5633e --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-uboot-univ.dts @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bone-common-univ.dtsi" + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-boneblack-uboot-univ.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; diff --git b/arch/arm/boot/dts/am335x-boneblack-uboot.dts b/arch/arm/boot/dts/am335x-boneblack-uboot.dts new file mode 100644 index 0000000..285a921 --- /dev/null +++ b/arch/arm/boot/dts/am335x-boneblack-uboot.dts @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "TI AM335x BeagleBone Black"; + compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-boneblack-uboot.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&cpu0_opp_table { + /* + * All PG 2.0 silicon may not support 1GHz but some of the early + * BeagleBone Blacks have PG 2.0 silicon which is guaranteed + * to support 1GHz OPP so enable it for PG 2.0 on this board. + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts index 3124d94..f98e0cf 100644 --- a/arch/arm/boot/dts/am335x-boneblack-wireless.dts +++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts @@ -8,11 +8,17 @@ #include "am335x-bone-common.dtsi" #include "am335x-boneblack-common.dtsi" #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Black Wireless"; compatible = "ti,am335x-bone-black-wireless", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + chosen { + base_dtb = "am335x-boneblack-wireless.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + wlan_en_reg: fixedregulator@2 { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator"; diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index d392866..40b17b9 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -7,10 +7,16 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include "am335x-boneblack-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Black"; compatible = "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-boneblack.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &cpu0_opp_table { diff --git a/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/am335x-boneblue.dts index 2f6652e..953093d 100644 --- a/arch/arm/boot/dts/am335x-boneblue.dts +++ b/arch/arm/boot/dts/am335x-boneblue.dts @@ -14,6 +14,8 @@ chosen { stdout-path = &uart0; + base_dtb = "am335x-boneblue.dts"; + base_dtb_timestamp = __TIMESTAMP__; }; leds { @@ -115,6 +117,153 @@ }; &am33xx_pinmux { + /*************************************************************************** + * Static Pinmux + ***************************************************************************/ + mux_helper_pins: pins { + pinctrl-single,pins = < + + /* GPIO Inputs */ + 0x09c 0x37 /*P8.9 Pause BUTTON, input pullup*/ + 0x098 0x37 /*P8.10 MODE BUTTON input pullup*/ + 0x1AC 0x37 /*P9.25 MPU-9150 INTERRUPT IN*/ + + /* Motor Control GPIO Out*/ + 0x088 ( PIN_OUTPUT | MUX_MODE7 ) /* (T13) gpmc_csn3.gpio2[0] - MDIR_1A different from cape! */ + 0x074 ( PIN_OUTPUT | MUX_MODE7 ) /* (U17) gpmc_wpn.gpio0[31] - P9.13, MDIR_1B */ + 0x040 ( PIN_OUTPUT | MUX_MODE7 ) /* (R13) gpmc_a0.gpio1[16] - P9.15, MDIR_2A */ + 0x0D8 ( PIN_OUTPUT | MUX_MODE7 ) /* (V4) lcd_data14.gpio0[10] - P8.31, MDIR_2B different from cape! */ + 0x0AC ( PIN_OUTPUT | MUX_MODE7 ) /* (R4) lcd_data3.gpio2[9] - P8.44, MDIR_3A */ + 0x0A8 ( PIN_OUTPUT | MUX_MODE7 ) /* (R3) lcd_data2.gpio2[8] - P8.43, MDIR_3B */ + 0x0A0 ( PIN_OUTPUT | MUX_MODE7 ) /* (R1) lcd_data0.gpio2[6] - P8.45, MDIR_4A */ + 0x0A4 ( PIN_OUTPUT | MUX_MODE7 ) /* (R2) lcd_data1.gpio2[7] - P8.46, MDIR_4B */ + 0x1B4 ( PIN_OUTPUT | MUX_MODE7 ) /* (D14) xdma_event_intr1.gpio0[20] - P9.41, MOT_STBY */ + + /* PRU encoder input */ + 0x038 0x36 /* P8_16,PRU0_r31_16,MODE6 */ + + /* PRU Servo output */ + 0x0e0 0x05 /*pru1_pru_r30_8, MODE5*/ + 0x0e8 0x05 /*pru1_pru_r30_10, MODE5 */ + 0x0e4 0x05 /*pr1_pru1_pru_r30_9, MODE5 */ + 0x0ec 0x05 /*pru1_pru_r30_11, MODE5 */ + 0x0b8 0x05 /*pru1_pru_r30_6, MODE5 */ + 0x0bc 0x05 /*pru1_pru_r30_7, MODE5 */ + 0x0b0 0x05 /*pru1_pru_r30_4, MODE5 */ + 0x0b4 0x05 /*pru1_pru_r30_5, MODE5 */ + 0x0C8 0x0F /*P8.36, SERVO_PWR GPIO OUT*/ + + /* WILINK 8 */ + 0x08c 0x0F /*P8.18 V12 A2DP FSYNC */ + 0x078 0x0F /*P9.12 A2DP_CLOCK*/ + >; + + /* D13 BLUE_GP0_PIN_5 gpio 3_20 */ + D13_default_pin: pinmux_D13_default_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + D13_gpio_pin: pinmux_D13_gpio_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + D13_gpio_pu_pin: pinmux_D13_gpio_pu_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + D13_gpio_pd_pin: pinmux_D13_gpio_pd_pin { + pinctrl-single,pins = < 0x1A8 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* H17 BLUE_GP1_PIN_4 gpio 3_1 */ + H17_default_pin: pinmux_H17_default_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + H17_gpio_pin: pinmux_H17_gpio_pin { + pinctrl-single,pins = < 0x10C ( PIN_OUTPUT | MUX_MODE7 ) >; }; + H17_gpio_pu_pin: pinmux_H17_gpio_pu_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + H17_gpio_pd_pin: pinmux_H17_gpio_pd_pin { + pinctrl-single,pins = < 0x10C ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* J15 BLUE_GP1_PIN_3 gpio 3_2 */ + J15_default_pin: pinmux_J15_default_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + J15_gpio_pin: pinmux_J15_gpio_pin { + pinctrl-single,pins = < 0x110 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + J15_gpio_pu_pin: pinmux_J15_gpio_pu_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + J15_gpio_pd_pin: pinmux_J15_gpio_pd_pin { + pinctrl-single,pins = < 0x110 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + /* P8_15 (ZCZ ball U13) */ + P8_15_default_pin: pinmux_P8_15_default_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { + pinctrl-single,pins = <0x03c 0x2F>; }; /* Mode 7, RxActive */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { + pinctrl-single,pins = <0x03c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { + pinctrl-single,pins = <0x03c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { + pinctrl-single,pins = <0x03c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { + pinctrl-single,pins = <0x03c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P8_15_pruin_pu_pin: pinmux_P8_15_pruin_pu_pin { + pinctrl-single,pins = <0x03c 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + P8_15_pruecapin_pu_pin: pinmux_P8_15_pruecapin_pu_pin { + pinctrl-single,pins = <0x03c 0x35>; }; /* Mode 5, Pull-Up, RxActive */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_default_pin: pinmux_P9_11_default_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { + pinctrl-single,pins = <0x070 0x2F>; }; /* Mode 7, RxActive */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { + pinctrl-single,pins = <0x070 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { + pinctrl-single,pins = <0x070 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { + pinctrl-single,pins = <0x070 0x36>; }; /* Mode 6, Pull-Up, RxActive */ + + /* P9_23 (ZCZ ball V14) */ + P9_23_default_pin: pinmux_P9_23_default_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { + pinctrl-single,pins = <0x044 0x2F>; }; /* Mode 7, RxActive */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { + pinctrl-single,pins = <0x044 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { + pinctrl-single,pins = <0x044 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { + pinctrl-single,pins = <0x044 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + + /* P9_28 (ZCZ ball C12) Audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { + pinctrl-single,pins = <0x19c 0x2F>; }; /* Mode 7, RxActive */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { + pinctrl-single,pins = <0x19c 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { + pinctrl-single,pins = <0x19c 0x27>; }; /* Mode 7, Pull-Down, RxActive */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { + pinctrl-single,pins = <0x19c 0x21>; }; /* Mode 1, Pull-Down, RxActive */ + P9_28_spi_pin: pinmux_P9_28_spi_pin { + pinctrl-single,pins = <0x19c 0x23>; }; /* Mode 3, Pull-Down, RxActive */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { + pinctrl-single,pins = <0x19c 0x24>; }; /* Mode 4, Pull-Down, RxActive */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { + pinctrl-single,pins = <0x19c 0x25>; }; /* Mode 5, Pull-Down, RxActive */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { + pinctrl-single,pins = <0x19c 0x26>; }; /* Mode 6, Pull-Down, RxActive */ + P9_28_audio_pin: pinmux_P9_28_audio_pin { + pinctrl-single,pins = <0x19c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)>; }; /* mcasp0_ahclkr.mcasp0_axr2 */ + + /* U16 BLUE_GP0_PIN_3 gpio 1_25 */ + U16_default_pin: pinmux_U16_default_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + U16_gpio_pin: pinmux_U16_gpio_pin { + pinctrl-single,pins = < 0x064 ( PIN_OUTPUT | MUX_MODE7 ) >; }; + U16_gpio_pu_pin: pinmux_U16_gpio_pu_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLUP | MUX_MODE7 ) >; }; + U16_gpio_pd_pin: pinmux_U16_gpio_pd_pin { + pinctrl-single,pins = < 0x064 ( PIN_INPUT_PULLDOWN | MUX_MODE7 ) >; }; + + }; + user_leds_s0: user_leds_s0 { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */ @@ -164,11 +313,11 @@ }; /* DSM2 */ - uart4_pins: pinmux_uart4_pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */ - >; - }; + //uart4_pins: pinmux_uart4_pins { + // pinctrl-single,pins = < + // AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */ + // >; + //}; /* UT5 */ uart5_pins: pinmux_uart5_pins { @@ -241,6 +390,54 @@ AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_OUTPUT, MUX_MODE7) /* (M16) gmii1_rxd0.gpio2[21] */ >; }; + + /* E1 */ + eqep0_pins: pinmux_eqep0_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR0, PIN_INPUT, MUX_MODE1) /* (B12) mcasp0_aclkr.eQEP0A_in */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_FSR, PIN_INPUT, MUX_MODE1) /* (C13) mcasp0_fsr.eQEP0B_in */ + >; + }; + + /* E2 */ + eqep1_pins: pinmux_eqep1_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_INPUT, MUX_MODE2) /* (V2) lcd_data12.eQEP1A_in */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_INPUT, MUX_MODE2) /* (V3) lcd_data13.eQEP1B_in */ + >; + }; + + /* E3 */ + eqep2_pins: pinmux_eqep2_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT, MUX_MODE4) /* (T12) gpmc_ad12.eQEP2A_in */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT, MUX_MODE4) /* (R12) gpmc_ad13.eQEP2B_in */ + >; + }; + + ehrpwm1_pins: pinmux_ehrpwm1_pins { + pinctrl-single,pins = < + 0x020 0x24 /* P8_19_pwm_pin */ + 0x024 0x24 /* P8_13_pwm_pin */ + >; + }; + + ehrpwm2_pins: pinmux_ehrpwm2_pins { + pinctrl-single,pins = < + 0x048 0x26 /* P9_14_pwm_pin */ + 0x04c 0x26 /* P9_16_pwm_pin */ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + 0x190 0x23 /* spi1_sclk */ + 0x194 0x23 /* spi1_d0 */ + 0x198 0x23 /* spi1_d1 */ + 0x144 ( PIN_OUTPUT | MUX_MODE2 ) /* spi1_cs0 */ + 0x164 ( PIN_OUTPUT | MUX_MODE2 ) /* spi1_cs1 */ + >; + }; }; &uart0 { @@ -264,12 +461,12 @@ status = "okay"; }; -&uart4 { - pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins>; - - status = "okay"; -}; +//&uart4 { +// pinctrl-names = "default"; +// pinctrl-0 = <&uart4_pins>; +// +// status = "okay"; +//}; &uart5 { pinctrl-names = "default"; @@ -404,12 +601,12 @@ }; }; -&tscadc { - status = "okay"; - adc { - ti,adc-channels = <0 1 2 3 4 5 6 7>; - }; -}; +//&tscadc { +// status = "okay"; +// adc { +// ti,adc-channels = <0 1 2 3 4 5 6 7>; +// }; +//}; &uart3 { pinctrl-names = "default"; @@ -428,6 +625,10 @@ clock-names = "ext-clk", "int-clk"; }; +&wkup_m3_ipc { + ti,scale-data-fw = "/*(DEBLOBBED)*/"; +}; + &dcan1 { pinctrl-names = "default"; pinctrl-0 = <&dcan1_pins>; @@ -442,3 +643,193 @@ line-name = "LS_BUF_EN"; }; }; + +&epwmss0 { + status = "okay"; +}; + +&eqep0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&eqep0_pins>; +}; + +&epwmss1 { + status = "okay"; +}; + +&eqep1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&eqep1_pins>; +}; + +&epwmss2 { + status = "okay"; +}; + +&eqep2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&eqep2_pins>; +}; + +&ocp { + /* activate the static pinmux helper list of pin modes above */ + test_helper: helper { + compatible = "bone-pinmux-helper"; + pinctrl-names = "default"; + pinctrl-0 = <&mux_helper_pins>; + + status = "okay"; + }; + + /* Encoder 4 (U13) */ + P8_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "pruin_pu", "gpio", "gpio_pu", "gpio_pd", "pruin", "qep", "pruecapin_pu"; + pinctrl-0 = <&P8_15_pruin_pu_pin>; + pinctrl-1 = <&P8_15_pruin_pu_pin>; + pinctrl-2 = <&P8_15_gpio_pin>; + pinctrl-3 = <&P8_15_gpio_pu_pin>; + pinctrl-4 = <&P8_15_gpio_pd_pin>; + pinctrl-5 = <&P8_15_pruin_pin>; + pinctrl-6 = <&P8_15_qep_pin>; + pinctrl-7 = <&P8_15_pruecapin_pu_pin>; + }; + + /* UART4 RX DSM */ + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "uart", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&P9_11_uart_pin>; + pinctrl-1 = <&P9_11_uart_pin>; + pinctrl-2 = <&P9_11_gpio_pin>; + pinctrl-3 = <&P9_11_gpio_pu_pin>; + pinctrl-4 = <&P9_11_gpio_pd_pin>; + }; + + /* U16 BLUE_GP0_PIN_3 gpio 1_25*/ + U16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&U16_default_pin>; + pinctrl-1 = <&U16_gpio_pin>; + pinctrl-2 = <&U16_gpio_pu_pin>; + pinctrl-3 = <&U16_gpio_pd_pin>; + }; + + + /* BLUE_GP0_PIN_3 gpio1_17*/ + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_pwm_pin>; + }; + + /* BLUE_GP0_PIN_5 gpio3_20 */ + D13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&D13_default_pin>; + pinctrl-1 = <&D13_gpio_pin>; + pinctrl-2 = <&D13_gpio_pu_pin>; + pinctrl-3 = <&D13_gpio_pd_pin>; + }; + + /* BLUE_GP0_PIN_6 gpio3_17 */ + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "pwm", "spi", "pwm2", "pruout", "pruin"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_pwm_pin>; + pinctrl-5 = <&P9_28_spi_pin>; + pinctrl-6 = <&P9_28_pwm2_pin>; + pinctrl-7 = <&P9_28_pruout_pin>; + pinctrl-8 = <&P9_28_pruin_pin>; + }; + + /* BLUE_GP1_PIN_3 gpio3_2 */ + J15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&J15_default_pin>; + pinctrl-1 = <&J15_gpio_pin>; + pinctrl-2 = <&J15_gpio_pu_pin>; + pinctrl-3 = <&J15_gpio_pd_pin>; + }; + + /* BLUE_GP1_PIN_4 gpio3_1 */ + H17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&H17_default_pin>; + pinctrl-1 = <&H17_gpio_pin>; + pinctrl-2 = <&H17_gpio_pu_pin>; + pinctrl-3 = <&H17_gpio_pd_pin>; + }; +}; + +/******************************************************************************* +* PWMSS +*******************************************************************************/ +&ehrpwm0 { + status = "okay"; +}; + +&ehrpwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&ehrpwm1_pins>; + status = "okay"; +}; + +&ehrpwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&ehrpwm2_pins>; + status = "okay"; +}; + +/******************************************************************************* + SPI +*******************************************************************************/ +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/1.0"; + reg = <0>; + spi-max-frequency = <24000000>; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/1.1"; + reg = <1>; + spi-max-frequency = <24000000>; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts new file mode 100644 index 0000000..50cc5b9 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-gateway.dts @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bonegreen-common.dtsi" +#include +/* #include "am335x-bone-jtag.dtsi" */ + +/ { + model = "SeeedStudio BeagleBone Green Gateway"; + compatible = "ti,am335x-bone-green-gateway", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + aliases { + rtc0 = &extrtc; + rtc1 = &rtc; + }; + + chosen { + base_dtb = "am335x-bonegreen-gateway.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + + wlan_en_reg: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us= <70000>; + + /* WL_EN */ + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + leds { + led6 { + label = "beaglebone:green:usr4"; + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "netdev"; + default-state = "off"; + }; + }; +}; + +&cpu0_opp_table { + /* + * Octavo Systems: + * The EFUSE_SMA register is not programmed for any of the AM335x wafers + * we get and we are not programming them during our production test. + * Therefore, from a DEVICE_ID revision point of view, the silicon looks + * like it is Revision 2.1. However, from an EFUSE_SMA point of view for + * the HW OPP table, the silicon looks like it is Revision 1.0 (ie the + * EFUSE_SMA register reads as all zeros). + */ + oppnitro-1000000000 { + opp-supported-hw = <0x06 0x0100>; + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&usbhost_pins>; + + bt_pins: pinmux_bt_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gmii1_txd0.gpio0_28 - BT_EN */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (L15) gmii1_rxd1.mmc2_clk */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLUP, MUX_MODE6 ) /* (J16) gmii1_txen.mmc2_cmd */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (J17) gmii1_rxdv.mmc2_dat0 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (J18) gmii1_txd3.mmc2_dat1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (K15) gmii1_txd2.mmc2_dat2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLUP, MUX_MODE5 ) /* (H16) gmii1_col.mmc2_dat3 */ + >; + }; + + uart2_grove_pins: pinmux_uart2_grove_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x90c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) + AM33XX_IOPAD(0x910, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gmii1_rxd3.uart3_rxd */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* gmii1_rxd2.uart3_txd */ + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT, MUX_MODE3) /* mdio_data.uart3_ctsn */ + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* mdio_clk.uart3_rtsn */ + >; + }; + + wl18xx_pins: pinmux_wl18xx_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gmii1_txclk.gpio3_9 WL_EN */ + AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) /* rmii1_refclk.gpio0_29 WL_IRQ */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7) /* gmii1_rxclk.gpio3_10 LS_BUF_EN */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLUP | MUX_MODE7) /* gmii1_txd1.gpio0[21] */ + >; + }; +}; + +&mac { + status = "disabled"; +}; + +&mmc3 { + dmas = <&edma_xbar 12 0 1 + &edma_xbar 13 0 2>; + dma-names = "tx", "rx"; + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + non-removable; + cap-power-off-card; + ti,needs-special-hs-handling; + keep-power-in-suspend; + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins &wl18xx_pins>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_grove_pins>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins &bt_pins>; + status = "okay"; + + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c0 { + extrtc: rtc@68 { + compatible = "dallas,ds1340"; + reg = <0x68>; + }; +}; + +// (K16) gmii1_txd1.gpio0[21] +&gpio0 { + usb_reset { + gpio-hog; + gpios = <21 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb_reset"; + }; +}; + +&gpio3 { + ls_buf_en { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; +}; + +&usb1 { + #address-cells = <1>; + #size-cells = <0>; + + hub@1 { + compatible = "usb424,9512"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: ethernet@1 { + compatible = "usb424,ec00"; + reg = <1>; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-wireless-common-univ.dtsi b/arch/arm/boot/dts/am335x-bonegreen-wireless-common-univ.dtsi new file mode 100644 index 0000000..6e372b4 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-wireless-common-univ.dtsi @@ -0,0 +1,2814 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ + +&am33xx_pinmux { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + + /* P8_02 GND */ + + + /* P8_03 (ZCZ ball R9) emmc */ + P8_03_default_pin: pinmux_P8_03_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pin: pinmux_P8_03_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pu_pin: pinmux_P8_03_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_pd_pin: pinmux_P8_03_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + P8_03_gpio_input_pin: pinmux_P8_03_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0818, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad6.gpio1_6 */ + + /* P8_04 (ZCZ ball T9) emmc */ + P8_04_default_pin: pinmux_P8_04_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pin: pinmux_P8_04_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pu_pin: pinmux_P8_04_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_pd_pin: pinmux_P8_04_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + P8_04_gpio_input_pin: pinmux_P8_04_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x081c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad7.gpio1_7 */ + + /* P8_05 (ZCZ ball R8) emmc */ + P8_05_default_pin: pinmux_P8_05_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pin: pinmux_P8_05_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pu_pin: pinmux_P8_05_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_pd_pin: pinmux_P8_05_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + P8_05_gpio_input_pin: pinmux_P8_05_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0808, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad2.gpio1_2 */ + + /* P8_06 (ZCZ ball T8) emmc */ + P8_06_default_pin: pinmux_P8_06_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pin: pinmux_P8_06_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pu_pin: pinmux_P8_06_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_pd_pin: pinmux_P8_06_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + P8_06_gpio_input_pin: pinmux_P8_06_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x080c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad3.gpio1_3 */ + + /* P8_07 (ZCZ ball R7) gpio2_2 */ + P8_07_default_pin: pinmux_P8_07_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pin: pinmux_P8_07_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pu_pin: pinmux_P8_07_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_pd_pin: pinmux_P8_07_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_gpio_input_pin: pinmux_P8_07_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_advn_ale.gpio2_2 */ + P8_07_timer_pin: pinmux_P8_07_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0890, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_advn_ale.timer4 */ + + /* P8_08 (ZCZ ball T7) gpio2_3 */ + P8_08_default_pin: pinmux_P8_08_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pin: pinmux_P8_08_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pu_pin: pinmux_P8_08_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_pd_pin: pinmux_P8_08_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_gpio_input_pin: pinmux_P8_08_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_oen_ren.gpio2_3 */ + P8_08_timer_pin: pinmux_P8_08_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0894, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_oen_ren.timer7 */ + + /* P8_09 (ZCZ ball T6) gpio2_5 */ + P8_09_default_pin: pinmux_P8_09_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pin: pinmux_P8_09_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pu_pin: pinmux_P8_09_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_pd_pin: pinmux_P8_09_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_gpio_input_pin: pinmux_P8_09_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_be0n_cle.gpio2_5 */ + P8_09_timer_pin: pinmux_P8_09_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x089c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_be0n_cle.timer5 */ + + /* P8_10 (ZCZ ball U6) gpio2_4 */ + P8_10_default_pin: pinmux_P8_10_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pin: pinmux_P8_10_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pu_pin: pinmux_P8_10_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_pd_pin: pinmux_P8_10_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_gpio_input_pin: pinmux_P8_10_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wen.gpio2_4 */ + P8_10_timer_pin: pinmux_P8_10_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0898, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* gpmc_wen.timer6 */ + + /* P8_11 (ZCZ ball R12) gpio1_13 */ + P8_11_default_pin: pinmux_P8_11_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pin: pinmux_P8_11_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pu_pin: pinmux_P8_11_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_pd_pin: pinmux_P8_11_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_gpio_input_pin: pinmux_P8_11_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P8_11_qep_pin: pinmux_P8_11_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad13.eqep2b_in */ + P8_11_pruout_pin: pinmux_P8_11_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad13.pru0_out15 */ + + /* P8_12 (ZCZ ball T12) gpio1_12 */ + P8_12_default_pin: pinmux_P8_12_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pin: pinmux_P8_12_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pu_pin: pinmux_P8_12_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_pd_pin: pinmux_P8_12_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_gpio_input_pin: pinmux_P8_12_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P8_12_qep_pin: pinmux_P8_12_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad12.eqep2a_in */ + P8_12_pruout_pin: pinmux_P8_12_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad12.pru0_out14 */ + + /* P8_13 (ZCZ ball T10) gpio0_23 */ + P8_13_default_pin: pinmux_P8_13_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pin: pinmux_P8_13_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pu_pin: pinmux_P8_13_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_pd_pin: pinmux_P8_13_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_gpio_input_pin: pinmux_P8_13_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P8_13_pwm_pin: pinmux_P8_13_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad9.ehrpwm2b */ + + /* P8_14 (ZCZ ball T11) wl1835: wl_en */ + + /* P8_15 (ZCZ ball U13) gpio1_15 */ + P8_15_default_pin: pinmux_P8_15_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pin: pinmux_P8_15_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pu_pin: pinmux_P8_15_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_pd_pin: pinmux_P8_15_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_gpio_input_pin: pinmux_P8_15_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P8_15_qep_pin: pinmux_P8_15_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad15.eqep2_strobe */ + P8_15_pru_ecap_pin: pinmux_P8_15_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_ad15.pr1_ecap0_ecap_capin_apwm_o */ + P8_15_pruin_pin: pinmux_P8_15_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad15.pru0_in15 */ + + /* P8_16 (ZCZ ball V13) gpio1_14 */ + P8_16_default_pin: pinmux_P8_16_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pin: pinmux_P8_16_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pu_pin: pinmux_P8_16_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_pd_pin: pinmux_P8_16_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_gpio_input_pin: pinmux_P8_16_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P8_16_qep_pin: pinmux_P8_16_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad14.eqep2_index */ + P8_16_pruin_pin: pinmux_P8_16_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad14.pru0_in14 */ + + /* P8_17 (ZCZ ball U12) wl1835: wl_irq */ + + /* P8_18 (ZCZ ball V12) gpio2_1 */ + P8_18_default_pin: pinmux_P8_18_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pin: pinmux_P8_18_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pu_pin: pinmux_P8_18_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_pd_pin: pinmux_P8_18_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P8_18_gpio_input_pin: pinmux_P8_18_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + + /* P8_19 (ZCZ ball U10) gpio0_22 */ + P8_19_default_pin: pinmux_P8_19_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pin: pinmux_P8_19_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pu_pin: pinmux_P8_19_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_pd_pin: pinmux_P8_19_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_gpio_input_pin: pinmux_P8_19_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad8.gpio0_22 */ + P8_19_pwm_pin: pinmux_P8_19_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0820, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad8.ehrpwm2a */ + + /* P8_20 (ZCZ ball V9) emmc */ + P8_20_default_pin: pinmux_P8_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pin: pinmux_P8_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pu_pin: pinmux_P8_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_pd_pin: pinmux_P8_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_gpio_input_pin: pinmux_P8_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn2.gpio1_31 */ + P8_20_pruout_pin: pinmux_P8_20_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_csn2.pru1_out13 */ + P8_20_pruin_pin: pinmux_P8_20_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0884, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_csn2.pru1_in13 */ + + /* P8_21 (ZCZ ball U9) emmc */ + P8_21_default_pin: pinmux_P8_21_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pin: pinmux_P8_21_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pu_pin: pinmux_P8_21_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_pd_pin: pinmux_P8_21_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_gpio_input_pin: pinmux_P8_21_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn1.gpio1_30 */ + P8_21_pruout_pin: pinmux_P8_21_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_csn1.pru1_out12 */ + P8_21_pruin_pin: pinmux_P8_21_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0880, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_csn1.pru1_in12 */ + + /* P8_22 (ZCZ ball V8) emmc */ + P8_22_default_pin: pinmux_P8_22_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pin: pinmux_P8_22_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pu_pin: pinmux_P8_22_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_pd_pin: pinmux_P8_22_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + P8_22_gpio_input_pin: pinmux_P8_22_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0814, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad5.gpio1_5 */ + + /* P8_23 (ZCZ ball U8) emmc */ + P8_23_default_pin: pinmux_P8_23_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pin: pinmux_P8_23_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pu_pin: pinmux_P8_23_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_pd_pin: pinmux_P8_23_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + P8_23_gpio_input_pin: pinmux_P8_23_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0810, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad4.gpio1_4 */ + + /* P8_24 (ZCZ ball V7) emmc */ + P8_24_default_pin: pinmux_P8_24_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pin: pinmux_P8_24_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pu_pin: pinmux_P8_24_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_pd_pin: pinmux_P8_24_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + P8_24_gpio_input_pin: pinmux_P8_24_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0804, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad1.gpio1_1 */ + + /* P8_25 (ZCZ ball U7) emmc */ + P8_25_default_pin: pinmux_P8_25_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pin: pinmux_P8_25_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pu_pin: pinmux_P8_25_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_pd_pin: pinmux_P8_25_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + P8_25_gpio_input_pin: pinmux_P8_25_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0800, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad0.gpio1_0 */ + + /* P8_26 (ZCZ ball V6) gpio-hog wl1835 */ + + /* P8_27 (ZCZ ball U5) hdmi */ + P8_27_default_pin: pinmux_P8_27_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pin: pinmux_P8_27_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pu_pin: pinmux_P8_27_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_pd_pin: pinmux_P8_27_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_gpio_input_pin: pinmux_P8_27_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P8_27_pruout_pin: pinmux_P8_27_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_vsync.pru1_out8 */ + P8_27_pruin_pin: pinmux_P8_27_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_vsync.pru1_in8 */ + + /* P8_28 (ZCZ ball V5) hdmi */ + P8_28_default_pin: pinmux_P8_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pin: pinmux_P8_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pu_pin: pinmux_P8_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_pd_pin: pinmux_P8_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_gpio_input_pin: pinmux_P8_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P8_28_pruout_pin: pinmux_P8_28_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_pclk.pru1_out10 */ + P8_28_pruin_pin: pinmux_P8_28_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_pclk.pru1_in10 */ + + /* P8_29 (ZCZ ball R5) hdmi */ + P8_29_default_pin: pinmux_P8_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pin: pinmux_P8_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pu_pin: pinmux_P8_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_pd_pin: pinmux_P8_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_gpio_input_pin: pinmux_P8_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P8_29_pruout_pin: pinmux_P8_29_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_hsync.pru1_out9 */ + P8_29_pruin_pin: pinmux_P8_29_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_hsync.pru1_in9 */ + + /* P8_30 (ZCZ ball R6) hdmi */ + P8_30_default_pin: pinmux_P8_30_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pin: pinmux_P8_30_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pu_pin: pinmux_P8_30_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_pd_pin: pinmux_P8_30_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_gpio_input_pin: pinmux_P8_30_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P8_30_pruout_pin: pinmux_P8_30_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_ac_bias_en.pru1_out11 */ + P8_30_pruin_pin: pinmux_P8_30_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE6) >; }; /* lcd_ac_bias_en.pru1_in11 */ + + /* P8_31 (ZCZ ball V4) hdmi */ + P8_31_default_pin: pinmux_P8_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pin: pinmux_P8_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pu_pin: pinmux_P8_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_pd_pin: pinmux_P8_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_gpio_input_pin: pinmux_P8_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data14.gpio0_10 */ + P8_31_qep_pin: pinmux_P8_31_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data14.eqep1_index */ + P8_31_uart_pin: pinmux_P8_31_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data14.uart5_rxd */ + + /* P8_32 (ZCZ ball T5) hdmi */ + P8_32_default_pin: pinmux_P8_32_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pin: pinmux_P8_32_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pu_pin: pinmux_P8_32_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_pd_pin: pinmux_P8_32_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_gpio_input_pin: pinmux_P8_32_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data15.gpio0_11 */ + P8_32_qep_pin: pinmux_P8_32_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08dc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data15.eqep1_strobe */ + + /* P8_33 (ZCZ ball V3) hdmi */ + P8_33_default_pin: pinmux_P8_33_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pin: pinmux_P8_33_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pu_pin: pinmux_P8_33_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_pd_pin: pinmux_P8_33_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_gpio_input_pin: pinmux_P8_33_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data13.gpio0_9 */ + P8_33_qep_pin: pinmux_P8_33_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data13.eqep1b_in */ + + /* P8_34 (ZCZ ball U4) hdmi */ + P8_34_default_pin: pinmux_P8_34_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pin: pinmux_P8_34_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pu_pin: pinmux_P8_34_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_pd_pin: pinmux_P8_34_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_gpio_input_pin: pinmux_P8_34_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data11.gpio2_17 */ + P8_34_pwm_pin: pinmux_P8_34_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08cc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data11.ehrpwm1b */ + + /* P8_35 (ZCZ ball V2) hdmi */ + P8_35_default_pin: pinmux_P8_35_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pin: pinmux_P8_35_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pu_pin: pinmux_P8_35_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_pd_pin: pinmux_P8_35_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_gpio_input_pin: pinmux_P8_35_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data12.gpio0_8 */ + P8_35_qep_pin: pinmux_P8_35_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08d0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* lcd_data12.eqep1a_in */ + + /* P8_36 (ZCZ ball U3) hdmi */ + P8_36_default_pin: pinmux_P8_36_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pin: pinmux_P8_36_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pu_pin: pinmux_P8_36_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_pd_pin: pinmux_P8_36_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_gpio_input_pin: pinmux_P8_36_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data10.gpio2_16 */ + P8_36_pwm_pin: pinmux_P8_36_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data10.ehrpwm1a */ + + /* P8_37 (ZCZ ball U1) hdmi */ + P8_37_default_pin: pinmux_P8_37_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pin: pinmux_P8_37_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pu_pin: pinmux_P8_37_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_pd_pin: pinmux_P8_37_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_gpio_input_pin: pinmux_P8_37_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data8.gpio2_14 */ + P8_37_pwm_pin: pinmux_P8_37_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data8.ehrpwm1_tripzone_input */ + P8_37_uart_pin: pinmux_P8_37_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data8.uart5_txd */ + + /* P8_38 (ZCZ ball U2) hdmi */ + P8_38_default_pin: pinmux_P8_38_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pin: pinmux_P8_38_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pu_pin: pinmux_P8_38_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_pd_pin: pinmux_P8_38_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_gpio_input_pin: pinmux_P8_38_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data9.gpio2_15 */ + P8_38_pwm_pin: pinmux_P8_38_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE2) >; }; /* lcd_data9.ehrpwm0_synco */ + P8_38_uart_pin: pinmux_P8_38_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08c4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* lcd_data9.uart5_rxd */ + + /* P8_39 (ZCZ ball T3) hdmi */ + P8_39_default_pin: pinmux_P8_39_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pin: pinmux_P8_39_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pu_pin: pinmux_P8_39_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_pd_pin: pinmux_P8_39_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_gpio_input_pin: pinmux_P8_39_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data6.gpio2_12 */ + P8_39_qep_pin: pinmux_P8_39_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data6.eqep2_index */ + P8_39_pruout_pin: pinmux_P8_39_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data6.pru1_out6 */ + P8_39_pruin_pin: pinmux_P8_39_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data6.pru1_in6 */ + + /* P8_40 (ZCZ ball T4) hdmi */ + P8_40_default_pin: pinmux_P8_40_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pin: pinmux_P8_40_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pu_pin: pinmux_P8_40_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_pd_pin: pinmux_P8_40_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_gpio_input_pin: pinmux_P8_40_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data7.gpio2_13 */ + P8_40_qep_pin: pinmux_P8_40_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data7.eqep2_strobe */ + P8_40_pruout_pin: pinmux_P8_40_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data7.pru1_out7 */ + P8_40_pruin_pin: pinmux_P8_40_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08bc, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data7.pru1_in7 */ + + /* P8_41 (ZCZ ball T1) hdmi */ + P8_41_default_pin: pinmux_P8_41_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pin: pinmux_P8_41_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pu_pin: pinmux_P8_41_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_pd_pin: pinmux_P8_41_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_gpio_input_pin: pinmux_P8_41_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data4.gpio2_10 */ + P8_41_qep_pin: pinmux_P8_41_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data4.eqep2a_in */ + P8_41_pruout_pin: pinmux_P8_41_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data4.pru1_out4 */ + P8_41_pruin_pin: pinmux_P8_41_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data4.pru1_in4 */ + + /* P8_42 (ZCZ ball T2) hdmi */ + P8_42_default_pin: pinmux_P8_42_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pin: pinmux_P8_42_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pu_pin: pinmux_P8_42_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_pd_pin: pinmux_P8_42_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_gpio_input_pin: pinmux_P8_42_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data5.gpio2_11 */ + P8_42_qep_pin: pinmux_P8_42_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* lcd_data5.eqep2b_in */ + P8_42_pruout_pin: pinmux_P8_42_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data5.pru1_out5 */ + P8_42_pruin_pin: pinmux_P8_42_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08b4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data5.pru1_in5 */ + + /* P8_43 (ZCZ ball R3) hdmi */ + P8_43_default_pin: pinmux_P8_43_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pin: pinmux_P8_43_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pu_pin: pinmux_P8_43_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_pd_pin: pinmux_P8_43_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_gpio_input_pin: pinmux_P8_43_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data2.gpio2_8 */ + P8_43_pwm_pin: pinmux_P8_43_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data2.ehrpwm2_tripzone_input */ + P8_43_pruout_pin: pinmux_P8_43_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data2.pru1_out2 */ + P8_43_pruin_pin: pinmux_P8_43_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data2.pru1_in2 */ + + /* P8_44 (ZCZ ball R4) hdmi */ + P8_44_default_pin: pinmux_P8_44_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pin: pinmux_P8_44_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pu_pin: pinmux_P8_44_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_pd_pin: pinmux_P8_44_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_gpio_input_pin: pinmux_P8_44_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data3.gpio2_9 */ + P8_44_pwm_pin: pinmux_P8_44_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data3.ehrpwm0_synco */ + P8_44_pruout_pin: pinmux_P8_44_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data3.pru1_out3 */ + P8_44_pruin_pin: pinmux_P8_44_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ac, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data3.pru1_in3 */ + + /* P8_45 (ZCZ ball R1) hdmi */ + P8_45_default_pin: pinmux_P8_45_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pin: pinmux_P8_45_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pu_pin: pinmux_P8_45_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_pd_pin: pinmux_P8_45_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_gpio_input_pin: pinmux_P8_45_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data0.gpio2_6 */ + P8_45_pwm_pin: pinmux_P8_45_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data0.ehrpwm2a */ + P8_45_pruout_pin: pinmux_P8_45_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data0.pru1_out0 */ + P8_45_pruin_pin: pinmux_P8_45_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data0.pru1_in0 */ + + /* P8_46 (ZCZ ball R2) hdmi */ + P8_46_default_pin: pinmux_P8_46_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pin: pinmux_P8_46_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pu_pin: pinmux_P8_46_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_pd_pin: pinmux_P8_46_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_gpio_input_pin: pinmux_P8_46_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_data1.gpio2_7 */ + P8_46_pwm_pin: pinmux_P8_46_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* lcd_data1.ehrpwm2b */ + P8_46_pruout_pin: pinmux_P8_46_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_data1.pru1_out1 */ + P8_46_pruin_pin: pinmux_P8_46_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08a4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_data1.pru1_in1 */ + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + + /* P9_02 GND */ + + /* P9_03 3V3 */ + + /* P9_04 3V3 */ + + /* P9_05 VDD_5V */ + + /* P9_06 VDD_5V */ + + /* P9_07 SYS_5V */ + + /* P9_08 SYS_5V */ + + /* P9_09 PWR_BUT */ + + /* P9_10 RSTn */ + + /* P9_11 (ZCZ ball T17) gpio0_30 */ + P9_11_default_pin: pinmux_P9_11_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pin: pinmux_P9_11_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pu_pin: pinmux_P9_11_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_pd_pin: pinmux_P9_11_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_gpio_input_pin: pinmux_P9_11_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P9_11_uart_pin: pinmux_P9_11_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wait0.uart4_rxd */ + + /* P9_12 (ZCZ ball U18) gpio1_28 */ + P9_12_default_pin: pinmux_P9_12_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pin: pinmux_P9_12_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pu_pin: pinmux_P9_12_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_pd_pin: pinmux_P9_12_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P9_12_gpio_input_pin: pinmux_P9_12_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + + /* P9_13 (ZCZ ball U17) gpio0_31 */ + P9_13_default_pin: pinmux_P9_13_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pin: pinmux_P9_13_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pu_pin: pinmux_P9_13_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_pd_pin: pinmux_P9_13_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_gpio_input_pin: pinmux_P9_13_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P9_13_uart_pin: pinmux_P9_13_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wpn.uart4_txd */ + + /* P9_14 (ZCZ ball U14) gpio1_18 */ + P9_14_default_pin: pinmux_P9_14_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pin: pinmux_P9_14_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pu_pin: pinmux_P9_14_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_pd_pin: pinmux_P9_14_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_gpio_input_pin: pinmux_P9_14_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P9_14_pwm_pin: pinmux_P9_14_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a2.ehrpwm1a */ + + /* P9_15 (ZCZ ball R13) gpio1_16 */ + P9_15_default_pin: pinmux_P9_15_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pin: pinmux_P9_15_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pu_pin: pinmux_P9_15_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_pd_pin: pinmux_P9_15_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_gpio_input_pin: pinmux_P9_15_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a0.gpio1_16 */ + P9_15_pwm_pin: pinmux_P9_15_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0840, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a0.ehrpwm1_tripzone_input */ + + /* P9_16 (ZCZ ball T14) gpio1_19 */ + P9_16_default_pin: pinmux_P9_16_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pin: pinmux_P9_16_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pu_pin: pinmux_P9_16_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_pd_pin: pinmux_P9_16_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_gpio_input_pin: pinmux_P9_16_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a3.gpio1_19 */ + P9_16_pwm_pin: pinmux_P9_16_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x084c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a3.ehrpwm1b */ + + /* P9_17 (ZCZ ball A16) gpio0_5 */ + P9_17_default_pin: pinmux_P9_17_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pin: pinmux_P9_17_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pu_pin: pinmux_P9_17_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_pd_pin: pinmux_P9_17_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_gpio_input_pin: pinmux_P9_17_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_INPUT | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P9_17_spi_cs_pin: pinmux_P9_17_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_cs0.spi0_cs0 */ + P9_17_i2c_pin: pinmux_P9_17_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_cs0.i2c1_scl */ + P9_17_pwm_pin: pinmux_P9_17_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_cs0.ehrpwm0_synci */ + P9_17_pru_uart_pin: pinmux_P9_17_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_cs0.pr1_uart0_txd */ + + /* P9_18 (ZCZ ball B16) gpio0_4 */ + P9_18_default_pin: pinmux_P9_18_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pin: pinmux_P9_18_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pu_pin: pinmux_P9_18_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_pd_pin: pinmux_P9_18_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_gpio_input_pin: pinmux_P9_18_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P9_18_spi_pin: pinmux_P9_18_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d1.spi0_d1 */ + P9_18_i2c_pin: pinmux_P9_18_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d1.i2c1_sda */ + P9_18_pwm_pin: pinmux_P9_18_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d1.ehrpwm0_tripzone_input */ + P9_18_pru_uart_pin: pinmux_P9_18_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d1.pr1_uart0_rxd */ + + /* P9_19 (ZCZ ball D17) i2c2_scl */ + P9_19_default_pin: pinmux_P9_19_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P9_19_gpio_pin: pinmux_P9_19_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_pu_pin: pinmux_P9_19_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_pd_pin: pinmux_P9_19_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_gpio_input_pin: pinmux_P9_19_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P9_19_timer_pin: pinmux_P9_19_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart1_rtsn.timer5 */ + P9_19_can_pin: pinmux_P9_19_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rtsn.dcan0_rx */ + P9_19_i2c_pin: pinmux_P9_19_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P9_19_spi_cs_pin: pinmux_P9_19_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_rtsn.spi1_cs1 */ + P9_19_pru_uart_pin: pinmux_P9_19_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rtsn.pr1_uart0_rts_n */ + + /* P9_20 (ZCZ ball D18) i2c2_sda */ + P9_20_default_pin: pinmux_P9_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P9_20_gpio_pin: pinmux_P9_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_pu_pin: pinmux_P9_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_pd_pin: pinmux_P9_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_gpio_input_pin: pinmux_P9_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_INPUT | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P9_20_timer_pin: pinmux_P9_20_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart1_ctsn.timer6 */ + P9_20_can_pin: pinmux_P9_20_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_ctsn.dcan0_tx */ + P9_20_i2c_pin: pinmux_P9_20_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P9_20_spi_cs_pin: pinmux_P9_20_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_ctsn.spi1_cs0 */ + P9_20_pru_uart_pin: pinmux_P9_20_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_ctsn.pr1_uart0_cts_n */ + + /* P9_21 (ZCZ ball B17) gpio0_3 */ + P9_21_default_pin: pinmux_P9_21_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pin: pinmux_P9_21_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pu_pin: pinmux_P9_21_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_pd_pin: pinmux_P9_21_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_gpio_input_pin: pinmux_P9_21_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P9_21_spi_pin: pinmux_P9_21_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d0.spi0_d0 */ + P9_21_uart_pin: pinmux_P9_21_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_d0.uart2_txd */ + P9_21_i2c_pin: pinmux_P9_21_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d0.i2c2_scl */ + P9_21_pwm_pin: pinmux_P9_21_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d0.ehrpwm0b */ + P9_21_pru_uart_pin: pinmux_P9_21_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d0.pr1_uart0_rts_n */ + + /* P9_22 (ZCZ ball A17) gpio0_2 */ + P9_22_default_pin: pinmux_P9_22_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pin: pinmux_P9_22_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pu_pin: pinmux_P9_22_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_pd_pin: pinmux_P9_22_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_gpio_input_pin: pinmux_P9_22_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_INPUT | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P9_22_spi_sclk_pin: pinmux_P9_22_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_sclk.spi0_sclk */ + P9_22_uart_pin: pinmux_P9_22_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_sclk.uart2_rxd */ + P9_22_i2c_pin: pinmux_P9_22_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_sclk.i2c2_sda */ + P9_22_pwm_pin: pinmux_P9_22_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_sclk.ehrpwm0a */ + P9_22_pru_uart_pin: pinmux_P9_22_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_sclk.pr1_uart0_cts_n */ + + /* P9_23 (ZCZ ball V14) gpio1_17 */ + P9_23_default_pin: pinmux_P9_23_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pin: pinmux_P9_23_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pu_pin: pinmux_P9_23_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_pd_pin: pinmux_P9_23_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_gpio_input_pin: pinmux_P9_23_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a1.gpio1_17 */ + P9_23_pwm_pin: pinmux_P9_23_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0844, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a1.ehrpwm0_synco */ + + /* P9_24 (ZCZ ball D15) gpio0_15 */ + P9_24_default_pin: pinmux_P9_24_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pin: pinmux_P9_24_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pu_pin: pinmux_P9_24_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_pd_pin: pinmux_P9_24_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_gpio_input_pin: pinmux_P9_24_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P9_24_uart_pin: pinmux_P9_24_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_txd.uart1_txd */ + P9_24_can_pin: pinmux_P9_24_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_txd.dcan1_rx */ + P9_24_i2c_pin: pinmux_P9_24_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_txd.i2c1_scl */ + P9_24_pru_uart_pin: pinmux_P9_24_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_txd.pr1_uart0_txd */ + P9_24_pruin_pin: pinmux_P9_24_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE6) >; }; /* uart1_txd.pru0_in16 */ + + /* P9_25 (ZCZ ball A14) audio */ + P9_25_default_pin: pinmux_P9_25_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pin: pinmux_P9_25_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pu_pin: pinmux_P9_25_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_pd_pin: pinmux_P9_25_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_gpio_input_pin: pinmux_P9_25_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P9_25_qep_pin: pinmux_P9_25_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkx.eqep0_strobe */ + P9_25_pruout_pin: pinmux_P9_25_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkx.pru0_out7 */ + P9_25_pruin_pin: pinmux_P9_25_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkx.pru0_in7 */ + + /* P9_26 (ZCZ ball D16) gpio0_14 */ + P9_26_default_pin: pinmux_P9_26_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pin: pinmux_P9_26_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pu_pin: pinmux_P9_26_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_pd_pin: pinmux_P9_26_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_gpio_input_pin: pinmux_P9_26_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P9_26_uart_pin: pinmux_P9_26_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_rxd.uart1_rxd */ + P9_26_can_pin: pinmux_P9_26_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rxd.dcan1_tx */ + P9_26_i2c_pin: pinmux_P9_26_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rxd.i2c1_sda */ + P9_26_pru_uart_pin: pinmux_P9_26_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rxd.pr1_uart0_rxd */ + P9_26_pruin_pin: pinmux_P9_26_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE6) >; }; /* uart1_rxd.pru1_in16 */ + + /* P9_27 (ZCZ ball C13) gpio3_19 */ + P9_27_default_pin: pinmux_P9_27_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pin: pinmux_P9_27_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pu_pin: pinmux_P9_27_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_pd_pin: pinmux_P9_27_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_gpio_input_pin: pinmux_P9_27_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P9_27_qep_pin: pinmux_P9_27_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsr.eqep0b_in */ + P9_27_pruout_pin: pinmux_P9_27_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsr.pru0_out5 */ + P9_27_pruin_pin: pinmux_P9_27_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsr.pru0_in5 */ + + /* P9_28 (ZCZ ball C12) audio */ + P9_28_default_pin: pinmux_P9_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pin: pinmux_P9_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pu_pin: pinmux_P9_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_pd_pin: pinmux_P9_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_gpio_input_pin: pinmux_P9_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P9_28_pwm_pin: pinmux_P9_28_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkr.ehrpwm0_synci */ + P9_28_spi_cs_pin: pinmux_P9_28_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_ahclkr.spi1_cs0 */ + P9_28_pwm2_pin: pinmux_P9_28_pwm2_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* mcasp0_ahclkr.ecap2_in_pwm2_out */ + P9_28_pruout_pin: pinmux_P9_28_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkr.pru0_out3 */ + P9_28_pruin_pin: pinmux_P9_28_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkr.pru0_in3 */ + + /* P9_29 (ZCZ ball B13) audio */ + P9_29_default_pin: pinmux_P9_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pin: pinmux_P9_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pu_pin: pinmux_P9_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_pd_pin: pinmux_P9_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_gpio_input_pin: pinmux_P9_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P9_29_pwm_pin: pinmux_P9_29_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsx.ehrpwm0b */ + P9_29_spi_pin: pinmux_P9_29_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_fsx.spi1_d0 */ + P9_29_pruout_pin: pinmux_P9_29_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsx.pru0_out1 */ + P9_29_pruin_pin: pinmux_P9_29_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsx.pru0_in1 */ + + /* P9_30 (ZCZ ball D12) gpio-hog wl1835 */ + + /* P9_31 (ZCZ ball A13) audio */ + P9_31_default_pin: pinmux_P9_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pin: pinmux_P9_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pu_pin: pinmux_P9_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_pd_pin: pinmux_P9_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_gpio_input_pin: pinmux_P9_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P9_31_pwm_pin: pinmux_P9_31_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkx.ehrpwm0a */ + P9_31_spi_sclk_pin: pinmux_P9_31_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_aclkx.spi1_sclk */ + P9_31_pruout_pin: pinmux_P9_31_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkx.pru0_out0 */ + P9_31_pruin_pin: pinmux_P9_31_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkx.pru0_in0 */ + + /* P9_32 VADC */ + + /* P9_33 (ZCZ ball C8) AIN4 */ + + /* P9_34 AGND */ + + /* P9_35 (ZCZ ball A8) AIN6 */ + + /* P9_36 (ZCZ ball B8) AIN5 */ + + /* P9_37 (ZCZ ball B7) AIN2 */ + + /* P9_38 (ZCZ ball A7) AIN3 */ + + /* P9_39 (ZCZ ball B6) AIN0 */ + + /* P9_40 (ZCZ ball C7) AIN1 */ + + /* P9_41 (ZCZ ball D14) gpio0_20 */ + P9_41_default_pin: pinmux_P9_41_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pin: pinmux_P9_41_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pu_pin: pinmux_P9_41_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_pd_pin: pinmux_P9_41_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_gpio_input_pin: pinmux_P9_41_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P9_41_timer_pin: pinmux_P9_41_timer_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* xdma_event_intr1.timer7 */ + P9_41_pruin_pin: pinmux_P9_41_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE5) >; }; /* xdma_event_intr1.pru0_in16 */ + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) gpio3_20 */ + P9_91_default_pin: pinmux_P9_91_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pin: pinmux_P9_91_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pu_pin: pinmux_P9_91_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_pd_pin: pinmux_P9_91_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_gpio_input_pin: pinmux_P9_91_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P9_91_qep_pin: pinmux_P9_91_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_axr1.eqep0_index */ + P9_91_pruout_pin: pinmux_P9_91_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_axr1.pru0_out6 */ + P9_91_pruin_pin: pinmux_P9_91_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr1.pru0_in6 */ + + /* P9_42 (ZCZ ball C18) gpio0_7 */ + P9_42_default_pin: pinmux_P9_42_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pin: pinmux_P9_42_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pu_pin: pinmux_P9_42_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_pd_pin: pinmux_P9_42_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_gpio_input_pin: pinmux_P9_42_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_INPUT | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P9_42_pwm_pin: pinmux_P9_42_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE0) >; }; /* eCAP0_in_PWM0_out.ecap0_in_pwm0_out */ + P9_42_uart_pin: pinmux_P9_42_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* eCAP0_in_PWM0_out.uart3_txd */ + P9_42_spi_cs_pin: pinmux_P9_42_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* eCAP0_in_PWM0_out.spi1_cs1 */ + P9_42_pru_ecap_pin: pinmux_P9_42_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* eCAP0_in_PWM0_out.pr1_ecap0_ecap_capin_apwm_o */ + P9_42_spi_sclk_pin: pinmux_P9_42_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* eCAP0_in_PWM0_out.spi1_sclk */ + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) gpio3_18 */ + P9_92_default_pin: pinmux_P9_92_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pin: pinmux_P9_92_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pu_pin: pinmux_P9_92_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_pd_pin: pinmux_P9_92_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_gpio_input_pin: pinmux_P9_92_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P9_92_qep_pin: pinmux_P9_92_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkr.eqep0a_in */ + P9_92_pruout_pin: pinmux_P9_92_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkr.pru0_out4 */ + P9_92_pruin_pin: pinmux_P9_92_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkr.pru0_in4 */ + + /* P9_43 GND */ + + /* P9_44 GND */ + + /* P9_45 GND */ + + /* P9_46 GND */ + + /* (ZCZ ball A15) */ + A15_default_pin: pinmux_A15_default_pin { + pinctrl-single,pins = <0x1b0 (PIN_OUTPUT_PULLUP | MUX_MODE7)>; }; /* Mode 7, Pull-Up */ + A15_clkout_pin: pinmux_A15_clkout_pin { + pinctrl-single,pins = <0x1b0 0x0b>; }; /* Mode 3 */ + A15_gpio_pin: pinmux_A15_gpio_pin { + pinctrl-single,pins = <0x1b0 0x2f>; }; /* Mode 7, RxActive */ + A15_gpio_pu_pin: pinmux_A15_gpio_pu_pin { + pinctrl-single,pins = <0x1b0 0x37>; }; /* Mode 7, Pull-Up, RxActive */ + A15_gpio_pd_pin: pinmux_A15_gpio_pd_pin { + pinctrl-single,pins = <0x1b0 0x27>; }; /* Mode 7, Pull-Down, RxActive */ +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + clock-frequency = <100000>; + symlink = "bone/i2c/1"; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + clock-frequency = <100000>; + symlink = "bone/i2c/2"; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/1"; +}; + +&uart2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/2"; +}; + +&uart3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/3"; +}; + +&uart4 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/4"; +}; + +&uart5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/uart/5"; +}; + +&dcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/can/0"; +}; + +&dcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/can/1"; +}; + +&eqep0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/0"; +}; + +&eqep1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/1"; +}; + +&eqep2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + symlink = "bone/eqep/2"; +}; + +&epwmss0 { + status = "okay"; +}; + +&epwmss1 { + status = "okay"; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ehrpwm1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ehrpwm2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ecap2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/0.0"; + + reg = <0>; + spi-max-frequency = <16000000>; + spi-cpha; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/0.1"; + + reg = <1>; + spi-max-frequency = <16000000>; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/1.0"; + + reg = <0>; + spi-max-frequency = <16000000>; + spi-cpha; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "spidev"; + symlink = "spi/1.1"; + + reg = <1>; + spi-max-frequency = <16000000>; + }; +}; + +/**********************************************************************/ +/* Pin Multiplex Helpers */ +/* */ +/* These provide userspace runtime pin configuration for the */ +/* BeagleBone cape expansion headers */ +/**********************************************************************/ + +&ocp { + /************************/ + /* P8 Header */ + /************************/ + + /* P8_01 GND */ + + /* P8_02 GND */ + + + /* P8_03 (ZCZ ball R9) emmc */ + P8_03_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_03_default_pin>; + pinctrl-1 = <&P8_03_gpio_pin>; + pinctrl-2 = <&P8_03_gpio_pu_pin>; + pinctrl-3 = <&P8_03_gpio_pd_pin>; + pinctrl-4 = <&P8_03_gpio_input_pin>; + }; + + /* P8_04 (ZCZ ball T9) emmc */ + P8_04_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_04_default_pin>; + pinctrl-1 = <&P8_04_gpio_pin>; + pinctrl-2 = <&P8_04_gpio_pu_pin>; + pinctrl-3 = <&P8_04_gpio_pd_pin>; + pinctrl-4 = <&P8_04_gpio_input_pin>; + }; + + /* P8_05 (ZCZ ball R8) emmc */ + P8_05_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_05_default_pin>; + pinctrl-1 = <&P8_05_gpio_pin>; + pinctrl-2 = <&P8_05_gpio_pu_pin>; + pinctrl-3 = <&P8_05_gpio_pd_pin>; + pinctrl-4 = <&P8_05_gpio_input_pin>; + }; + + /* P8_06 (ZCZ ball T8) emmc */ + P8_06_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_06_default_pin>; + pinctrl-1 = <&P8_06_gpio_pin>; + pinctrl-2 = <&P8_06_gpio_pu_pin>; + pinctrl-3 = <&P8_06_gpio_pd_pin>; + pinctrl-4 = <&P8_06_gpio_input_pin>; + }; + + /* P8_07 (ZCZ ball R7) */ + P8_07_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_07_default_pin>; + pinctrl-1 = <&P8_07_gpio_pin>; + pinctrl-2 = <&P8_07_gpio_pu_pin>; + pinctrl-3 = <&P8_07_gpio_pd_pin>; + pinctrl-4 = <&P8_07_gpio_input_pin>; + pinctrl-5 = <&P8_07_timer_pin>; + }; + + /* P8_08 (ZCZ ball T7) */ + P8_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_08_default_pin>; + pinctrl-1 = <&P8_08_gpio_pin>; + pinctrl-2 = <&P8_08_gpio_pu_pin>; + pinctrl-3 = <&P8_08_gpio_pd_pin>; + pinctrl-4 = <&P8_08_gpio_input_pin>; + pinctrl-5 = <&P8_08_timer_pin>; + }; + + /* P8_09 (ZCZ ball T6) */ + P8_09_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_09_default_pin>; + pinctrl-1 = <&P8_09_gpio_pin>; + pinctrl-2 = <&P8_09_gpio_pu_pin>; + pinctrl-3 = <&P8_09_gpio_pd_pin>; + pinctrl-4 = <&P8_09_gpio_input_pin>; + pinctrl-5 = <&P8_09_timer_pin>; + }; + + /* P8_10 (ZCZ ball U6) */ + P8_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer"; + pinctrl-0 = <&P8_10_default_pin>; + pinctrl-1 = <&P8_10_gpio_pin>; + pinctrl-2 = <&P8_10_gpio_pu_pin>; + pinctrl-3 = <&P8_10_gpio_pd_pin>; + pinctrl-4 = <&P8_10_gpio_input_pin>; + pinctrl-5 = <&P8_10_timer_pin>; + }; + + /* P8_11 (ZCZ ball R12) */ + P8_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P8_11_default_pin>; + pinctrl-1 = <&P8_11_gpio_pin>; + pinctrl-2 = <&P8_11_gpio_pu_pin>; + pinctrl-3 = <&P8_11_gpio_pd_pin>; + pinctrl-4 = <&P8_11_gpio_input_pin>; + pinctrl-5 = <&P8_11_qep_pin>; + pinctrl-6 = <&P8_11_pruout_pin>; + }; + + /* P8_12 (ZCZ ball T12) */ + P8_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P8_12_default_pin>; + pinctrl-1 = <&P8_12_gpio_pin>; + pinctrl-2 = <&P8_12_gpio_pu_pin>; + pinctrl-3 = <&P8_12_gpio_pd_pin>; + pinctrl-4 = <&P8_12_gpio_input_pin>; + pinctrl-5 = <&P8_12_qep_pin>; + pinctrl-6 = <&P8_12_pruout_pin>; + }; + + /* P8_13 (ZCZ ball T10) */ + P8_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_13_default_pin>; + pinctrl-1 = <&P8_13_gpio_pin>; + pinctrl-2 = <&P8_13_gpio_pu_pin>; + pinctrl-3 = <&P8_13_gpio_pd_pin>; + pinctrl-4 = <&P8_13_gpio_input_pin>; + pinctrl-5 = <&P8_13_pwm_pin>; + }; + + /* P8_14 (ZCZ ball T11) wl1835: wl_en */ + + /* P8_15 (ZCZ ball U13) */ + P8_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pru_ecap", "pruin"; + pinctrl-0 = <&P8_15_default_pin>; + pinctrl-1 = <&P8_15_gpio_pin>; + pinctrl-2 = <&P8_15_gpio_pu_pin>; + pinctrl-3 = <&P8_15_gpio_pd_pin>; + pinctrl-4 = <&P8_15_gpio_input_pin>; + pinctrl-5 = <&P8_15_qep_pin>; + pinctrl-6 = <&P8_15_pru_ecap_pin>; + pinctrl-7 = <&P8_15_pruin_pin>; + }; + + /* P8_16 (ZCZ ball V13) */ + P8_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruin"; + pinctrl-0 = <&P8_16_default_pin>; + pinctrl-1 = <&P8_16_gpio_pin>; + pinctrl-2 = <&P8_16_gpio_pu_pin>; + pinctrl-3 = <&P8_16_gpio_pd_pin>; + pinctrl-4 = <&P8_16_gpio_input_pin>; + pinctrl-5 = <&P8_16_qep_pin>; + pinctrl-6 = <&P8_16_pruin_pin>; + }; + + /* P8_17 (ZCZ ball U12) wl1835: wl_irq */ + + /* P8_18 (ZCZ ball V12) */ + P8_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_18_default_pin>; + pinctrl-1 = <&P8_18_gpio_pin>; + pinctrl-2 = <&P8_18_gpio_pu_pin>; + pinctrl-3 = <&P8_18_gpio_pd_pin>; + pinctrl-4 = <&P8_18_gpio_input_pin>; + }; + + /* P8_19 (ZCZ ball U10) */ + P8_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_19_default_pin>; + pinctrl-1 = <&P8_19_gpio_pin>; + pinctrl-2 = <&P8_19_gpio_pu_pin>; + pinctrl-3 = <&P8_19_gpio_pd_pin>; + pinctrl-4 = <&P8_19_gpio_input_pin>; + pinctrl-5 = <&P8_19_pwm_pin>; + }; + + /* P8_20 (ZCZ ball V9) emmc */ + P8_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_20_default_pin>; + pinctrl-1 = <&P8_20_gpio_pin>; + pinctrl-2 = <&P8_20_gpio_pu_pin>; + pinctrl-3 = <&P8_20_gpio_pd_pin>; + pinctrl-4 = <&P8_20_gpio_input_pin>; + pinctrl-5 = <&P8_20_pruout_pin>; + pinctrl-6 = <&P8_20_pruin_pin>; + }; + + /* P8_21 (ZCZ ball U9) emmc */ + P8_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_21_default_pin>; + pinctrl-1 = <&P8_21_gpio_pin>; + pinctrl-2 = <&P8_21_gpio_pu_pin>; + pinctrl-3 = <&P8_21_gpio_pd_pin>; + pinctrl-4 = <&P8_21_gpio_input_pin>; + pinctrl-5 = <&P8_21_pruout_pin>; + pinctrl-6 = <&P8_21_pruin_pin>; + }; + + /* P8_22 (ZCZ ball V8) emmc */ + P8_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_22_default_pin>; + pinctrl-1 = <&P8_22_gpio_pin>; + pinctrl-2 = <&P8_22_gpio_pu_pin>; + pinctrl-3 = <&P8_22_gpio_pd_pin>; + pinctrl-4 = <&P8_22_gpio_input_pin>; + }; + + /* P8_23 (ZCZ ball U8) emmc */ + P8_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_23_default_pin>; + pinctrl-1 = <&P8_23_gpio_pin>; + pinctrl-2 = <&P8_23_gpio_pu_pin>; + pinctrl-3 = <&P8_23_gpio_pd_pin>; + pinctrl-4 = <&P8_23_gpio_input_pin>; + }; + + /* P8_24 (ZCZ ball V7) emmc */ + P8_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_24_default_pin>; + pinctrl-1 = <&P8_24_gpio_pin>; + pinctrl-2 = <&P8_24_gpio_pu_pin>; + pinctrl-3 = <&P8_24_gpio_pd_pin>; + pinctrl-4 = <&P8_24_gpio_input_pin>; + }; + + /* P8_25 (ZCZ ball U7) emmc */ + P8_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P8_25_default_pin>; + pinctrl-1 = <&P8_25_gpio_pin>; + pinctrl-2 = <&P8_25_gpio_pu_pin>; + pinctrl-3 = <&P8_25_gpio_pd_pin>; + pinctrl-4 = <&P8_25_gpio_input_pin>; + }; + + /* P8_26 (ZCZ ball V6) gpio-hog wl1835 */ + + /* P8_27 (ZCZ ball U5) hdmi */ + P8_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_27_default_pin>; + pinctrl-1 = <&P8_27_gpio_pin>; + pinctrl-2 = <&P8_27_gpio_pu_pin>; + pinctrl-3 = <&P8_27_gpio_pd_pin>; + pinctrl-4 = <&P8_27_gpio_input_pin>; + pinctrl-5 = <&P8_27_pruout_pin>; + pinctrl-6 = <&P8_27_pruin_pin>; + }; + + /* P8_28 (ZCZ ball V5) hdmi */ + P8_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_28_default_pin>; + pinctrl-1 = <&P8_28_gpio_pin>; + pinctrl-2 = <&P8_28_gpio_pu_pin>; + pinctrl-3 = <&P8_28_gpio_pd_pin>; + pinctrl-4 = <&P8_28_gpio_input_pin>; + pinctrl-5 = <&P8_28_pruout_pin>; + pinctrl-6 = <&P8_28_pruin_pin>; + }; + + /* P8_29 (ZCZ ball R5) hdmi */ + P8_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_29_default_pin>; + pinctrl-1 = <&P8_29_gpio_pin>; + pinctrl-2 = <&P8_29_gpio_pu_pin>; + pinctrl-3 = <&P8_29_gpio_pd_pin>; + pinctrl-4 = <&P8_29_gpio_input_pin>; + pinctrl-5 = <&P8_29_pruout_pin>; + pinctrl-6 = <&P8_29_pruin_pin>; + }; + + /* P8_30 (ZCZ ball R6) hdmi */ + P8_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P8_30_default_pin>; + pinctrl-1 = <&P8_30_gpio_pin>; + pinctrl-2 = <&P8_30_gpio_pu_pin>; + pinctrl-3 = <&P8_30_gpio_pd_pin>; + pinctrl-4 = <&P8_30_gpio_input_pin>; + pinctrl-5 = <&P8_30_pruout_pin>; + pinctrl-6 = <&P8_30_pruin_pin>; + }; + + /* P8_31 (ZCZ ball V4) hdmi */ + P8_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "qep"; + pinctrl-0 = <&P8_31_default_pin>; + pinctrl-1 = <&P8_31_gpio_pin>; + pinctrl-2 = <&P8_31_gpio_pu_pin>; + pinctrl-3 = <&P8_31_gpio_pd_pin>; + pinctrl-4 = <&P8_31_gpio_input_pin>; + pinctrl-5 = <&P8_31_uart_pin>; + pinctrl-6 = <&P8_31_qep_pin>; + }; + + /* P8_32 (ZCZ ball T5) hdmi */ + P8_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_32_default_pin>; + pinctrl-1 = <&P8_32_gpio_pin>; + pinctrl-2 = <&P8_32_gpio_pu_pin>; + pinctrl-3 = <&P8_32_gpio_pd_pin>; + pinctrl-4 = <&P8_32_gpio_input_pin>; + pinctrl-5 = <&P8_32_qep_pin>; + }; + + /* P8_33 (ZCZ ball V3) hdmi */ + P8_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_33_default_pin>; + pinctrl-1 = <&P8_33_gpio_pin>; + pinctrl-2 = <&P8_33_gpio_pu_pin>; + pinctrl-3 = <&P8_33_gpio_pd_pin>; + pinctrl-4 = <&P8_33_gpio_input_pin>; + pinctrl-5 = <&P8_33_qep_pin>; + }; + + /* P8_34 (ZCZ ball U4) hdmi */ + P8_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_34_default_pin>; + pinctrl-1 = <&P8_34_gpio_pin>; + pinctrl-2 = <&P8_34_gpio_pu_pin>; + pinctrl-3 = <&P8_34_gpio_pd_pin>; + pinctrl-4 = <&P8_34_gpio_input_pin>; + pinctrl-5 = <&P8_34_pwm_pin>; + }; + + /* P8_35 (ZCZ ball V2) hdmi */ + P8_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P8_35_default_pin>; + pinctrl-1 = <&P8_35_gpio_pin>; + pinctrl-2 = <&P8_35_gpio_pu_pin>; + pinctrl-3 = <&P8_35_gpio_pd_pin>; + pinctrl-4 = <&P8_35_gpio_input_pin>; + pinctrl-5 = <&P8_35_qep_pin>; + }; + + /* P8_36 (ZCZ ball U3) hdmi */ + P8_36_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P8_36_default_pin>; + pinctrl-1 = <&P8_36_gpio_pin>; + pinctrl-2 = <&P8_36_gpio_pu_pin>; + pinctrl-3 = <&P8_36_gpio_pd_pin>; + pinctrl-4 = <&P8_36_gpio_input_pin>; + pinctrl-5 = <&P8_36_pwm_pin>; + }; + + /* P8_37 (ZCZ ball U1) hdmi */ + P8_37_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "pwm"; + pinctrl-0 = <&P8_37_default_pin>; + pinctrl-1 = <&P8_37_gpio_pin>; + pinctrl-2 = <&P8_37_gpio_pu_pin>; + pinctrl-3 = <&P8_37_gpio_pd_pin>; + pinctrl-4 = <&P8_37_gpio_input_pin>; + pinctrl-5 = <&P8_37_uart_pin>; + pinctrl-6 = <&P8_37_pwm_pin>; + }; + + /* P8_38 (ZCZ ball U2) hdmi */ + P8_38_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "pwm"; + pinctrl-0 = <&P8_38_default_pin>; + pinctrl-1 = <&P8_38_gpio_pin>; + pinctrl-2 = <&P8_38_gpio_pu_pin>; + pinctrl-3 = <&P8_38_gpio_pd_pin>; + pinctrl-4 = <&P8_38_gpio_input_pin>; + pinctrl-5 = <&P8_38_uart_pin>; + pinctrl-6 = <&P8_38_pwm_pin>; + }; + + /* P8_39 (ZCZ ball T3) hdmi */ + P8_39_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_39_default_pin>; + pinctrl-1 = <&P8_39_gpio_pin>; + pinctrl-2 = <&P8_39_gpio_pu_pin>; + pinctrl-3 = <&P8_39_gpio_pd_pin>; + pinctrl-4 = <&P8_39_gpio_input_pin>; + pinctrl-5 = <&P8_39_qep_pin>; + pinctrl-6 = <&P8_39_pruout_pin>; + pinctrl-7 = <&P8_39_pruin_pin>; + }; + + /* P8_40 (ZCZ ball T4) hdmi */ + P8_40_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_40_default_pin>; + pinctrl-1 = <&P8_40_gpio_pin>; + pinctrl-2 = <&P8_40_gpio_pu_pin>; + pinctrl-3 = <&P8_40_gpio_pd_pin>; + pinctrl-4 = <&P8_40_gpio_input_pin>; + pinctrl-5 = <&P8_40_qep_pin>; + pinctrl-6 = <&P8_40_pruout_pin>; + pinctrl-7 = <&P8_40_pruin_pin>; + }; + + /* P8_41 (ZCZ ball T1) hdmi */ + P8_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_41_default_pin>; + pinctrl-1 = <&P8_41_gpio_pin>; + pinctrl-2 = <&P8_41_gpio_pu_pin>; + pinctrl-3 = <&P8_41_gpio_pd_pin>; + pinctrl-4 = <&P8_41_gpio_input_pin>; + pinctrl-5 = <&P8_41_qep_pin>; + pinctrl-6 = <&P8_41_pruout_pin>; + pinctrl-7 = <&P8_41_pruin_pin>; + }; + + /* P8_42 (ZCZ ball T2) hdmi */ + P8_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P8_42_default_pin>; + pinctrl-1 = <&P8_42_gpio_pin>; + pinctrl-2 = <&P8_42_gpio_pu_pin>; + pinctrl-3 = <&P8_42_gpio_pd_pin>; + pinctrl-4 = <&P8_42_gpio_input_pin>; + pinctrl-5 = <&P8_42_qep_pin>; + pinctrl-6 = <&P8_42_pruout_pin>; + pinctrl-7 = <&P8_42_pruin_pin>; + }; + + /* P8_43 (ZCZ ball R3) hdmi */ + P8_43_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_43_default_pin>; + pinctrl-1 = <&P8_43_gpio_pin>; + pinctrl-2 = <&P8_43_gpio_pu_pin>; + pinctrl-3 = <&P8_43_gpio_pd_pin>; + pinctrl-4 = <&P8_43_gpio_input_pin>; + pinctrl-5 = <&P8_43_pwm_pin>; + pinctrl-6 = <&P8_43_pruout_pin>; + pinctrl-7 = <&P8_43_pruin_pin>; + }; + + /* P8_44 (ZCZ ball R4) hdmi */ + P8_44_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_44_default_pin>; + pinctrl-1 = <&P8_44_gpio_pin>; + pinctrl-2 = <&P8_44_gpio_pu_pin>; + pinctrl-3 = <&P8_44_gpio_pd_pin>; + pinctrl-4 = <&P8_44_gpio_input_pin>; + pinctrl-5 = <&P8_44_pwm_pin>; + pinctrl-6 = <&P8_44_pruout_pin>; + pinctrl-7 = <&P8_44_pruin_pin>; + }; + + /* P8_45 (ZCZ ball R1) hdmi */ + P8_45_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_45_default_pin>; + pinctrl-1 = <&P8_45_gpio_pin>; + pinctrl-2 = <&P8_45_gpio_pu_pin>; + pinctrl-3 = <&P8_45_gpio_pd_pin>; + pinctrl-4 = <&P8_45_gpio_input_pin>; + pinctrl-5 = <&P8_45_pwm_pin>; + pinctrl-6 = <&P8_45_pruout_pin>; + pinctrl-7 = <&P8_45_pruin_pin>; + }; + + /* P8_46 (ZCZ ball R2) hdmi */ + P8_46_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P8_46_default_pin>; + pinctrl-1 = <&P8_46_gpio_pin>; + pinctrl-2 = <&P8_46_gpio_pu_pin>; + pinctrl-3 = <&P8_46_gpio_pd_pin>; + pinctrl-4 = <&P8_46_gpio_input_pin>; + pinctrl-5 = <&P8_46_pwm_pin>; + pinctrl-6 = <&P8_46_pruout_pin>; + pinctrl-7 = <&P8_46_pruin_pin>; + }; + + /************************/ + /* P9 Header */ + /************************/ + + /* P9_01 GND */ + + /* P9_02 GND */ + + /* P9_03 3V3 */ + + /* P9_04 3V3 */ + + /* P9_05 VDD_5V */ + + /* P9_06 VDD_5V */ + + /* P9_07 SYS_5V */ + + /* P9_08 SYS_5V */ + + /* P9_09 PWR_BUT */ + + /* P9_10 RSTn */ + + /* P9_11 (ZCZ ball T17) */ + P9_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P9_11_default_pin>; + pinctrl-1 = <&P9_11_gpio_pin>; + pinctrl-2 = <&P9_11_gpio_pu_pin>; + pinctrl-3 = <&P9_11_gpio_pd_pin>; + pinctrl-4 = <&P9_11_gpio_input_pin>; + pinctrl-5 = <&P9_11_uart_pin>; + }; + + /* P9_12 (ZCZ ball U18) */ + P9_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P9_12_default_pin>; + pinctrl-1 = <&P9_12_gpio_pin>; + pinctrl-2 = <&P9_12_gpio_pu_pin>; + pinctrl-3 = <&P9_12_gpio_pd_pin>; + pinctrl-4 = <&P9_12_gpio_input_pin>; + }; + + /* P9_13 (ZCZ ball U17) */ + P9_13_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P9_13_default_pin>; + pinctrl-1 = <&P9_13_gpio_pin>; + pinctrl-2 = <&P9_13_gpio_pu_pin>; + pinctrl-3 = <&P9_13_gpio_pd_pin>; + pinctrl-4 = <&P9_13_gpio_input_pin>; + pinctrl-5 = <&P9_13_uart_pin>; + }; + + /* P9_14 (ZCZ ball U14) */ + P9_14_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_14_default_pin>; + pinctrl-1 = <&P9_14_gpio_pin>; + pinctrl-2 = <&P9_14_gpio_pu_pin>; + pinctrl-3 = <&P9_14_gpio_pd_pin>; + pinctrl-4 = <&P9_14_gpio_input_pin>; + pinctrl-5 = <&P9_14_pwm_pin>; + }; + + /* P9_15 (ZCZ ball R13) */ + P9_15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_15_default_pin>; + pinctrl-1 = <&P9_15_gpio_pin>; + pinctrl-2 = <&P9_15_gpio_pu_pin>; + pinctrl-3 = <&P9_15_gpio_pd_pin>; + pinctrl-4 = <&P9_15_gpio_input_pin>; + pinctrl-5 = <&P9_15_pwm_pin>; + }; + + /* P9_16 (ZCZ ball T14) */ + P9_16_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_16_default_pin>; + pinctrl-1 = <&P9_16_gpio_pin>; + pinctrl-2 = <&P9_16_gpio_pu_pin>; + pinctrl-3 = <&P9_16_gpio_pd_pin>; + pinctrl-4 = <&P9_16_gpio_input_pin>; + pinctrl-5 = <&P9_16_pwm_pin>; + }; + + /* P9_17 (ZCZ ball A16) */ + P9_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_17_default_pin>; + pinctrl-1 = <&P9_17_gpio_pin>; + pinctrl-2 = <&P9_17_gpio_pu_pin>; + pinctrl-3 = <&P9_17_gpio_pd_pin>; + pinctrl-4 = <&P9_17_gpio_input_pin>; + pinctrl-5 = <&P9_17_spi_cs_pin>; + pinctrl-6 = <&P9_17_i2c_pin>; + pinctrl-7 = <&P9_17_pwm_pin>; + pinctrl-8 = <&P9_17_pru_uart_pin>; + }; + + /* P9_18 (ZCZ ball B16) */ + P9_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_18_default_pin>; + pinctrl-1 = <&P9_18_gpio_pin>; + pinctrl-2 = <&P9_18_gpio_pu_pin>; + pinctrl-3 = <&P9_18_gpio_pd_pin>; + pinctrl-4 = <&P9_18_gpio_input_pin>; + pinctrl-5 = <&P9_18_spi_pin>; + pinctrl-6 = <&P9_18_i2c_pin>; + pinctrl-7 = <&P9_18_pwm_pin>; + pinctrl-8 = <&P9_18_pru_uart_pin>; + }; + + /* P9_19 (ZCZ ball D17) i2c */ + P9_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart", "timer"; + pinctrl-0 = <&P9_19_default_pin>; + pinctrl-1 = <&P9_19_gpio_pin>; + pinctrl-2 = <&P9_19_gpio_pu_pin>; + pinctrl-3 = <&P9_19_gpio_pd_pin>; + pinctrl-4 = <&P9_19_gpio_input_pin>; + pinctrl-5 = <&P9_19_spi_cs_pin>; + pinctrl-6 = <&P9_19_can_pin>; + pinctrl-7 = <&P9_19_i2c_pin>; + pinctrl-8 = <&P9_19_pru_uart_pin>; + pinctrl-9 = <&P9_19_timer_pin>; + }; + + /* P9_20 (ZCZ ball D18) i2c */ + P9_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart", "timer"; + pinctrl-0 = <&P9_20_default_pin>; + pinctrl-1 = <&P9_20_gpio_pin>; + pinctrl-2 = <&P9_20_gpio_pu_pin>; + pinctrl-3 = <&P9_20_gpio_pd_pin>; + pinctrl-4 = <&P9_20_gpio_input_pin>; + pinctrl-5 = <&P9_20_spi_cs_pin>; + pinctrl-6 = <&P9_20_can_pin>; + pinctrl-7 = <&P9_20_i2c_pin>; + pinctrl-8 = <&P9_20_pru_uart_pin>; + pinctrl-9 = <&P9_20_timer_pin>; + }; + + /* P9_21 (ZCZ ball B17) */ + P9_21_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_21_default_pin>; + pinctrl-1 = <&P9_21_gpio_pin>; + pinctrl-2 = <&P9_21_gpio_pu_pin>; + pinctrl-3 = <&P9_21_gpio_pd_pin>; + pinctrl-4 = <&P9_21_gpio_input_pin>; + pinctrl-5 = <&P9_21_spi_pin>; + pinctrl-6 = <&P9_21_uart_pin>; + pinctrl-7 = <&P9_21_i2c_pin>; + pinctrl-8 = <&P9_21_pwm_pin>; + pinctrl-9 = <&P9_21_pru_uart_pin>; + }; + + /* P9_22 (ZCZ ball A17) */ + P9_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P9_22_default_pin>; + pinctrl-1 = <&P9_22_gpio_pin>; + pinctrl-2 = <&P9_22_gpio_pu_pin>; + pinctrl-3 = <&P9_22_gpio_pd_pin>; + pinctrl-4 = <&P9_22_gpio_input_pin>; + pinctrl-5 = <&P9_22_spi_sclk_pin>; + pinctrl-6 = <&P9_22_uart_pin>; + pinctrl-7 = <&P9_22_i2c_pin>; + pinctrl-8 = <&P9_22_pwm_pin>; + pinctrl-9 = <&P9_22_pru_uart_pin>; + }; + + /* P9_23 (ZCZ ball V14) */ + P9_23_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P9_23_default_pin>; + pinctrl-1 = <&P9_23_gpio_pin>; + pinctrl-2 = <&P9_23_gpio_pu_pin>; + pinctrl-3 = <&P9_23_gpio_pd_pin>; + pinctrl-4 = <&P9_23_gpio_input_pin>; + pinctrl-5 = <&P9_23_pwm_pin>; + }; + + /* P9_24 (ZCZ ball D15) */ + P9_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P9_24_default_pin>; + pinctrl-1 = <&P9_24_gpio_pin>; + pinctrl-2 = <&P9_24_gpio_pu_pin>; + pinctrl-3 = <&P9_24_gpio_pd_pin>; + pinctrl-4 = <&P9_24_gpio_input_pin>; + pinctrl-5 = <&P9_24_uart_pin>; + pinctrl-6 = <&P9_24_can_pin>; + pinctrl-7 = <&P9_24_i2c_pin>; + pinctrl-8 = <&P9_24_pru_uart_pin>; + pinctrl-9 = <&P9_24_pruin_pin>; + }; + + /* P9_25 (ZCZ ball A14) audio */ + P9_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_25_default_pin>; + pinctrl-1 = <&P9_25_gpio_pin>; + pinctrl-2 = <&P9_25_gpio_pu_pin>; + pinctrl-3 = <&P9_25_gpio_pd_pin>; + pinctrl-4 = <&P9_25_gpio_input_pin>; + pinctrl-5 = <&P9_25_qep_pin>; + pinctrl-6 = <&P9_25_pruout_pin>; + pinctrl-7 = <&P9_25_pruin_pin>; + }; + + /* P9_26 (ZCZ ball D16) */ + P9_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P9_26_default_pin>; + pinctrl-1 = <&P9_26_gpio_pin>; + pinctrl-2 = <&P9_26_gpio_pu_pin>; + pinctrl-3 = <&P9_26_gpio_pd_pin>; + pinctrl-4 = <&P9_26_gpio_input_pin>; + pinctrl-5 = <&P9_26_uart_pin>; + pinctrl-6 = <&P9_26_can_pin>; + pinctrl-7 = <&P9_26_i2c_pin>; + pinctrl-8 = <&P9_26_pru_uart_pin>; + pinctrl-9 = <&P9_26_pruin_pin>; + }; + + /* P9_27 (ZCZ ball C13) */ + P9_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_27_default_pin>; + pinctrl-1 = <&P9_27_gpio_pin>; + pinctrl-2 = <&P9_27_gpio_pu_pin>; + pinctrl-3 = <&P9_27_gpio_pd_pin>; + pinctrl-4 = <&P9_27_gpio_input_pin>; + pinctrl-5 = <&P9_27_qep_pin>; + pinctrl-6 = <&P9_27_pruout_pin>; + pinctrl-7 = <&P9_27_pruin_pin>; + }; + + /* P9_28 (ZCZ ball C12) audio */ + P9_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "pwm", "pwm2", "pruout", "pruin"; + pinctrl-0 = <&P9_28_default_pin>; + pinctrl-1 = <&P9_28_gpio_pin>; + pinctrl-2 = <&P9_28_gpio_pu_pin>; + pinctrl-3 = <&P9_28_gpio_pd_pin>; + pinctrl-4 = <&P9_28_gpio_input_pin>; + pinctrl-5 = <&P9_28_spi_cs_pin>; + pinctrl-6 = <&P9_28_pwm_pin>; + pinctrl-7 = <&P9_28_pwm2_pin>; + pinctrl-8 = <&P9_28_pruout_pin>; + pinctrl-9 = <&P9_28_pruin_pin>; + }; + + /* P9_29 (ZCZ ball B13) audio */ + P9_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P9_29_default_pin>; + pinctrl-1 = <&P9_29_gpio_pin>; + pinctrl-2 = <&P9_29_gpio_pu_pin>; + pinctrl-3 = <&P9_29_gpio_pd_pin>; + pinctrl-4 = <&P9_29_gpio_input_pin>; + pinctrl-5 = <&P9_29_spi_pin>; + pinctrl-6 = <&P9_29_pwm_pin>; + pinctrl-7 = <&P9_29_pruout_pin>; + pinctrl-8 = <&P9_29_pruin_pin>; + }; + + /* P9_30 (ZCZ ball D12) gpio-hog wl1835 */ + + /* P9_31 (ZCZ ball A13) audio */ + P9_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P9_31_default_pin>; + pinctrl-1 = <&P9_31_gpio_pin>; + pinctrl-2 = <&P9_31_gpio_pu_pin>; + pinctrl-3 = <&P9_31_gpio_pd_pin>; + pinctrl-4 = <&P9_31_gpio_input_pin>; + pinctrl-5 = <&P9_31_spi_sclk_pin>; + pinctrl-6 = <&P9_31_pwm_pin>; + pinctrl-7 = <&P9_31_pruout_pin>; + pinctrl-8 = <&P9_31_pruin_pin>; + }; + + /* P9_32 VADC */ + + /* P9_33 (ZCZ ball C8) AIN4 */ + + /* P9_34 AGND */ + + /* P9_35 (ZCZ ball A8) AIN6 */ + + /* P9_36 (ZCZ ball B8) AIN5 */ + + /* P9_37 (ZCZ ball B7) AIN2 */ + + /* P9_38 (ZCZ ball A7) AIN3 */ + + /* P9_39 (ZCZ ball B6) AIN0 */ + + /* P9_40 (ZCZ ball C7) AIN1 */ + + /* P9_41 (ZCZ ball D14) */ + P9_41_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "timer", "pruin"; + pinctrl-0 = <&P9_41_default_pin>; + pinctrl-1 = <&P9_41_gpio_pin>; + pinctrl-2 = <&P9_41_gpio_pu_pin>; + pinctrl-3 = <&P9_41_gpio_pd_pin>; + pinctrl-4 = <&P9_41_gpio_input_pin>; + pinctrl-5 = <&P9_41_timer_pin>; + pinctrl-6 = <&P9_41_pruin_pin>; + }; + + /* P9_41.1 */ + /* P9_91 (ZCZ ball D13) */ + P9_91_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_91_default_pin>; + pinctrl-1 = <&P9_91_gpio_pin>; + pinctrl-2 = <&P9_91_gpio_pu_pin>; + pinctrl-3 = <&P9_91_gpio_pd_pin>; + pinctrl-4 = <&P9_91_gpio_input_pin>; + pinctrl-5 = <&P9_91_qep_pin>; + pinctrl-6 = <&P9_91_pruout_pin>; + pinctrl-7 = <&P9_91_pruin_pin>; + }; + + /* P9_42 (ZCZ ball C18) */ + P9_42_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "spi_sclk", "uart", "pwm", "pru_ecap"; + pinctrl-0 = <&P9_42_default_pin>; + pinctrl-1 = <&P9_42_gpio_pin>; + pinctrl-2 = <&P9_42_gpio_pu_pin>; + pinctrl-3 = <&P9_42_gpio_pd_pin>; + pinctrl-4 = <&P9_42_gpio_input_pin>; + pinctrl-5 = <&P9_42_spi_cs_pin>; + pinctrl-6 = <&P9_42_spi_sclk_pin>; + pinctrl-7 = <&P9_42_uart_pin>; + pinctrl-8 = <&P9_42_pwm_pin>; + pinctrl-9 = <&P9_42_pru_ecap_pin>; + }; + + /* P9_42.1 */ + /* P9_92 (ZCZ ball B12) */ + P9_92_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P9_92_default_pin>; + pinctrl-1 = <&P9_92_gpio_pin>; + pinctrl-2 = <&P9_92_gpio_pu_pin>; + pinctrl-3 = <&P9_92_gpio_pd_pin>; + pinctrl-4 = <&P9_92_gpio_input_pin>; + pinctrl-5 = <&P9_92_qep_pin>; + pinctrl-6 = <&P9_92_pruout_pin>; + pinctrl-7 = <&P9_92_pruin_pin>; + }; + + /* P9_43 GND */ + + /* P9_44 GND */ + + /* P9_45 GND */ + + /* P9_46 GND */ + + /* (ZCZ ball A15) */ + A15_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "clkout", "gpio", "gpio_pu", "gpio_pd"; + pinctrl-0 = <&A15_default_pin>; + pinctrl-1 = <&A15_clkout_pin>; + pinctrl-2 = <&A15_gpio_pin>; + pinctrl-3 = <&A15_gpio_pu_pin>; + pinctrl-4 = <&A15_gpio_pd_pin>; + }; + + cape-universal { + compatible = "gpio-of-helper"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + P8_03 { + gpio-name = "P8_03"; + gpio = <&gpio1 6 0>; + input; + dir-changeable; + }; + + P8_04 { + gpio-name = "P8_04"; + gpio = <&gpio1 7 0>; + input; + dir-changeable; + }; + + P8_05 { + gpio-name = "P8_05"; + gpio = <&gpio1 2 0>; + input; + dir-changeable; + }; + + P8_06 { + gpio-name = "P8_06"; + gpio = <&gpio1 3 0>; + input; + dir-changeable; + }; + + P8_07 { + gpio-name = "P8_07"; + gpio = <&gpio2 2 0>; + input; + dir-changeable; + }; + + P8_08 { + gpio-name = "P8_08"; + gpio = <&gpio2 3 0>; + input; + dir-changeable; + }; + + P8_09 { + gpio-name = "P8_09"; + gpio = <&gpio2 5 0>; + input; + dir-changeable; + }; + + P8_10 { + gpio-name = "P8_10"; + gpio = <&gpio2 4 0>; + input; + dir-changeable; + }; + + P8_11 { + gpio-name = "P8_11"; + gpio = <&gpio1 13 0>; + input; + dir-changeable; + }; + + P8_12 { + gpio-name = "P8_12"; + gpio = <&gpio1 12 0>; + input; + dir-changeable; + }; + + P8_13 { + gpio-name = "P8_13"; + gpio = <&gpio0 23 0>; + input; + dir-changeable; + }; + + P8_15 { + gpio-name = "P8_15"; + gpio = <&gpio1 15 0>; + input; + dir-changeable; + }; + + P8_16 { + gpio-name = "P8_16"; + gpio = <&gpio1 14 0>; + input; + dir-changeable; + }; + + P8_18 { + gpio-name = "P8_18"; + gpio = <&gpio2 1 0>; + input; + dir-changeable; + }; + + P8_19 { + gpio-name = "P8_19"; + gpio = <&gpio0 22 0>; + input; + dir-changeable; + }; + + P8_20 { + gpio-name = "P8_20"; + gpio = <&gpio1 31 0>; + input; + dir-changeable; + }; + + P8_21 { + gpio-name = "P8_21"; + gpio = <&gpio1 30 0>; + input; + dir-changeable; + }; + + P8_22 { + gpio-name = "P8_22"; + gpio = <&gpio1 5 0>; + input; + dir-changeable; + }; + + P8_23 { + gpio-name = "P8_23"; + gpio = <&gpio1 4 0>; + input; + dir-changeable; + }; + + P8_24 { + gpio-name = "P8_24"; + gpio = <&gpio1 1 0>; + input; + dir-changeable; + }; + + P8_25 { + gpio-name = "P8_25"; + gpio = <&gpio1 0 0>; + input; + dir-changeable; + }; + + P8_27 { + gpio-name = "P8_27"; + gpio = <&gpio2 22 0>; + input; + dir-changeable; + }; + + P8_28 { + gpio-name = "P8_28"; + gpio = <&gpio2 24 0>; + input; + dir-changeable; + }; + + P8_29 { + gpio-name = "P8_29"; + gpio = <&gpio2 23 0>; + input; + dir-changeable; + }; + + P8_30 { + gpio-name = "P8_30"; + gpio = <&gpio2 25 0>; + input; + dir-changeable; + }; + + P8_31 { + gpio-name = "P8_31"; + gpio = <&gpio0 10 0>; + input; + dir-changeable; + }; + + P8_32 { + gpio-name = "P8_32"; + gpio = <&gpio0 11 0>; + input; + dir-changeable; + }; + + P8_33 { + gpio-name = "P8_33"; + gpio = <&gpio0 9 0>; + input; + dir-changeable; + }; + + P8_34 { + gpio-name = "P8_34"; + gpio = <&gpio2 17 0>; + input; + dir-changeable; + }; + + P8_35 { + gpio-name = "P8_35"; + gpio = <&gpio0 8 0>; + input; + dir-changeable; + }; + + P8_36 { + gpio-name = "P8_36"; + gpio = <&gpio2 16 0>; + input; + dir-changeable; + }; + + P8_37 { + gpio-name = "P8_37"; + gpio = <&gpio2 14 0>; + input; + dir-changeable; + }; + + P8_38 { + gpio-name = "P8_38"; + gpio = <&gpio2 15 0>; + input; + dir-changeable; + }; + + P8_39 { + gpio-name = "P8_39"; + gpio = <&gpio2 12 0>; + input; + dir-changeable; + }; + + P8_40 { + gpio-name = "P8_40"; + gpio = <&gpio2 13 0>; + input; + dir-changeable; + }; + + P8_41 { + gpio-name = "P8_41"; + gpio = <&gpio2 10 0>; + input; + dir-changeable; + }; + + P8_42 { + gpio-name = "P8_42"; + gpio = <&gpio2 11 0>; + input; + dir-changeable; + }; + + P8_43 { + gpio-name = "P8_43"; + gpio = <&gpio2 8 0>; + input; + dir-changeable; + }; + + P8_44 { + gpio-name = "P8_44"; + gpio = <&gpio2 9 0>; + input; + dir-changeable; + }; + + P8_45 { + gpio-name = "P8_45"; + gpio = <&gpio2 6 0>; + input; + dir-changeable; + }; + + P8_46 { + gpio-name = "P8_46"; + gpio = <&gpio2 7 0>; + input; + dir-changeable; + }; + + P9_11 { + gpio-name = "P9_11"; + gpio = <&gpio0 30 0>; + input; + dir-changeable; + }; + + P9_12 { + gpio-name = "P9_12"; + gpio = <&gpio1 28 0>; + input; + dir-changeable; + }; + + P9_13 { + gpio-name = "P9_13"; + gpio = <&gpio0 31 0>; + input; + dir-changeable; + }; + + P9_14 { + gpio-name = "P9_14"; + gpio = <&gpio1 18 0>; + input; + dir-changeable; + }; + + P9_15 { + gpio-name = "P9_15"; + gpio = <&gpio1 16 0>; + input; + dir-changeable; + }; + + P9_16 { + gpio-name = "P9_16"; + gpio = <&gpio1 19 0>; + input; + dir-changeable; + }; + + P9_17 { + gpio-name = "P9_17"; + gpio = <&gpio0 5 0>; + input; + dir-changeable; + }; + + P9_18 { + gpio-name = "P9_18"; + gpio = <&gpio0 4 0>; + input; + dir-changeable; + }; + + P9_19 { + gpio-name = "P9_19"; + gpio = <&gpio0 13 0>; + input; + dir-changeable; + }; + + P9_20 { + gpio-name = "P9_20"; + gpio = <&gpio0 12 0>; + input; + dir-changeable; + }; + + P9_21 { + gpio-name = "P9_21"; + gpio = <&gpio0 3 0>; + input; + dir-changeable; + }; + + P9_22 { + gpio-name = "P9_22"; + gpio = <&gpio0 2 0>; + input; + dir-changeable; + }; + + P9_23 { + gpio-name = "P9_23"; + gpio = <&gpio1 17 0>; + input; + dir-changeable; + }; + + P9_24 { + gpio-name = "P9_24"; + gpio = <&gpio0 15 0>; + input; + dir-changeable; + }; + + P9_25 { + gpio-name = "P9_25"; + gpio = <&gpio3 21 0>; + input; + dir-changeable; + }; + + P9_26 { + gpio-name = "P9_26"; + gpio = <&gpio0 14 0>; + input; + dir-changeable; + }; + + P9_27 { + gpio-name = "P9_27"; + gpio = <&gpio3 19 0>; + input; + dir-changeable; + }; + + P9_28 { + gpio-name = "P9_28"; + gpio = <&gpio3 17 0>; + input; + dir-changeable; + }; + + P9_29 { + gpio-name = "P9_29"; + gpio = <&gpio3 15 0>; + input; + dir-changeable; + }; + + P9_31 { + gpio-name = "P9_31"; + gpio = <&gpio3 14 0>; + input; + dir-changeable; + }; + + P9_41 { + gpio-name = "P9_41"; + gpio = <&gpio0 20 0>; + input; + dir-changeable; + }; + + P9_91 { + gpio-name = "P9_91"; + gpio = <&gpio3 20 0>; + input; + dir-changeable; + }; + + P9_42 { + gpio-name = "P9_42"; + gpio = <&gpio0 7 0>; + input; + dir-changeable; + }; + + P9_92 { + gpio-name = "P9_92"; + gpio = <&gpio3 18 0>; + input; + dir-changeable; + }; + + A15 { + gpio-name = "A15"; + gpio = <&gpio0 19 0>; + input; + dir-changeable; + }; + }; +}; diff --git b/arch/arm/boot/dts/am335x-bonegreen-wireless-uboot-univ.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless-uboot-univ.dts new file mode 100644 index 0000000..ac63c24 --- /dev/null +++ b/arch/arm/boot/dts/am335x-bonegreen-wireless-uboot-univ.dts @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ +/dts-v1/; + +#include "am33xx.dtsi" +#include "am335x-bone-common.dtsi" +#include "am335x-bonegreen-wireless-common-univ.dtsi" + +/ { + model = "TI AM335x BeagleBone Green Wireless"; + compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bonegreen-wireless-uboot-univ.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; +}; + +&ldo3_reg { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&mmc1 { + vmmc-supply = <&vmmcsd_fixed>; +}; + +&gpio1 { + ls_buf_en { + gpio-hog; + gpios = <29 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "LS_BUF_EN"; + }; +}; + +/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/ +/* in case it isn't, wilink8 ends up in one of the test modes that */ +/* intruces various issues (elp wkaeup timeouts etc.) */ +/* On the BBGW this pin is routed through the level shifter (U21) that */ +/* introduces a pullup on the line and wilink8 ends up in a bad state. */ +/* use a gpio hog to force this pin low. An alternative may be adding */ +/* an external pulldown on U21 pin 4. */ + +&gpio3 { + bt_aud_in { + gpio-hog; + gpios = <16 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "MCASP0_AHCLKR"; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts index 4092cd1..a0a841d 100644 --- a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts +++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts @@ -8,11 +8,17 @@ #include "am335x-bone-common.dtsi" #include "am335x-bonegreen-common.dtsi" #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Green Wireless"; compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + chosen { + base_dtb = "am335x-bonegreen-wireless.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + wlan_en_reg: fixedregulator@2 { compatible = "regulator-fixed"; regulator-name = "wlan-en-regulator"; diff --git a/arch/arm/boot/dts/am335x-bonegreen.dts b/arch/arm/boot/dts/am335x-bonegreen.dts index c12bb07..d3009ae 100644 --- a/arch/arm/boot/dts/am335x-bonegreen.dts +++ b/arch/arm/boot/dts/am335x-bonegreen.dts @@ -7,8 +7,14 @@ #include "am33xx.dtsi" #include "am335x-bone-common.dtsi" #include "am335x-bonegreen-common.dtsi" +/* #include "am335x-bone-jtag.dtsi" */ / { model = "TI AM335x BeagleBone Green"; compatible = "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-bonegreen.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts index f47cc9f..bdb7838 100644 --- a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts +++ b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts @@ -13,10 +13,16 @@ #include #include +/* #include "am335x-bone-jtag.dtsi" */ / { model = "Octavo Systems OSD3358-SM-RED"; compatible = "oct,osd3358-sm-refdesign", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-osd3358-sm-red.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &ldo3_reg { @@ -40,7 +46,6 @@ &am33xx_pinmux { nxp_hdmi_bonelt_pins: nxp-hdmi-bonelt-pins { pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) @@ -64,12 +69,6 @@ >; }; - nxp_hdmi_bonelt_off_pins: nxp-hdmi-bonelt-off-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3) - >; - }; - mcasp0_pins: mcasp0-pins { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) @@ -124,9 +123,8 @@ compatible = "nxp,tda998x"; reg = <0x70>; - pinctrl-names = "default", "off"; + pinctrl-names = "default"; pinctrl-0 = <&nxp_hdmi_bonelt_pins>; - pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; /* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */ /* video-ports = <0x234501>; */ @@ -264,9 +262,6 @@ }; &am33xx_pinmux { - pinctrl-names = "default"; - pinctrl-0 = <&clkout2_pin>; - user_leds_s0: user-leds-s0 { pinctrl-single,pins = < AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a5.gpio1_21 */ @@ -290,12 +285,6 @@ >; }; - clkout2_pin: pinmux-clkout2-pin { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_OUTPUT_PULLDOWN, MUX_MODE3) /* xdma_event_intr1.clkout2 */ - >; - }; - cpsw_default: cpsw-default { pinctrl-single,pins = < /* Slave 1 */ diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts index abf2bad..d2533a8 100644 --- a/arch/arm/boot/dts/am335x-pocketbeagle.dts +++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts @@ -15,6 +15,8 @@ chosen { stdout-path = &uart0; + base_dtb = "am335x-pocketbeagle.dts"; + base_dtb_timestamp = __TIMESTAMP__; }; leds { @@ -60,24 +62,24 @@ }; &am33xx_pinmux { - i2c2_pins: pinmux-i2c2-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */ - AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */ - >; - }; +// i2c2_pins: pinmux-i2c2-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */ +// AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */ +// >; +// }; - ehrpwm0_pins: pinmux-ehrpwm0-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */ - >; - }; +// ehrpwm0_pins: pinmux-ehrpwm0-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */ +// >; +// }; - ehrpwm1_pins: pinmux-ehrpwm1-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */ - >; - }; +// ehrpwm1_pins: pinmux-ehrpwm1-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */ +// >; +// }; mmc0_pins: pinmux-mmc0-pins { pinctrl-single,pins = < @@ -91,23 +93,23 @@ >; }; - spi0_pins: pinmux-spi0-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0) - AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0) - AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0) - AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0) - >; - }; +// spi0_pins: pinmux-spi0-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLUP, MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */ +// AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT_PULLUP, MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */ +// AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLUP, MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */ +// AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLUP, MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */ +// >; +// }; - spi1_pins: pinmux-spi1-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */ - AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */ - AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */ - AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */ - >; - }; +// spi1_pins: pinmux-spi1-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */ +// AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */ +// AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */ +// AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */ +// >; +// }; usr_leds_pins: pinmux-usr-leds-pins { pinctrl-single,pins = < @@ -125,12 +127,839 @@ >; }; - uart4_pins: pinmux-uart4-pins { - pinctrl-single,pins = < - AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */ - AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */ - >; - }; +// uart4_pins: pinmux-uart4-pins { +// pinctrl-single,pins = < +// AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */ +// AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_OUTPUT_PULLDOWN, MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */ +// >; +// }; + + /************************/ + /* P1 Header */ + /************************/ + + /* P1_01 VIN-AC */ + + /* P1_02 (ZCZ ball R5) gpio2_23 */ + P1_02_default_pin: pinmux_P1_02_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P1_02_gpio_pin: pinmux_P1_02_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P1_02_gpio_pu_pin: pinmux_P1_02_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P1_02_gpio_pd_pin: pinmux_P1_02_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P1_02_gpio_input_pin: pinmux_P1_02_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE7) >; }; /* lcd_hsync.gpio2_23 */ + P1_02_pruout_pin: pinmux_P1_02_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_hsync.pru1_out9 */ + P1_02_pruin_pin: pinmux_P1_02_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e4, PIN_INPUT | MUX_MODE6) >; }; /* lcd_hsync.pru1_in9 */ + + /* P1_03 (ZCZ ball F15) usb1_vbus_out */ + + /* P1_04 (ZCZ ball R6) gpio2_25 */ + P1_04_default_pin: pinmux_P1_04_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P1_04_gpio_pin: pinmux_P1_04_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P1_04_gpio_pu_pin: pinmux_P1_04_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P1_04_gpio_pd_pin: pinmux_P1_04_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P1_04_gpio_input_pin: pinmux_P1_04_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE7) >; }; /* lcd_ac_bias_en.gpio2_25 */ + P1_04_pruout_pin: pinmux_P1_04_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_ac_bias_en.pru1_out11 */ + P1_04_pruin_pin: pinmux_P1_04_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08ec, PIN_INPUT | MUX_MODE6) >; }; /* lcd_ac_bias_en.pru1_in11 */ + + /* P1_05 (ZCZ ball T18) usb1_vbus_in */ + + /* P1_06 (ZCZ ball A16) spi0_cs0 */ + P1_06_default_pin: pinmux_P1_06_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_cs0.spi0_cs0 */ + P1_06_gpio_pin: pinmux_P1_06_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P1_06_gpio_pu_pin: pinmux_P1_06_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P1_06_gpio_pd_pin: pinmux_P1_06_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P1_06_gpio_input_pin: pinmux_P1_06_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_INPUT | MUX_MODE7) >; }; /* spi0_cs0.gpio0_5 */ + P1_06_spi_cs_pin: pinmux_P1_06_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_cs0.spi0_cs0 */ + P1_06_i2c_pin: pinmux_P1_06_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_cs0.i2c1_scl */ + P1_06_pwm_pin: pinmux_P1_06_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_cs0.ehrpwm0_synci */ + P1_06_pru_uart_pin: pinmux_P1_06_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x095c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_cs0.pr1_uart0_txd */ + + /* P1_07 VIN-USB */ + + /* P1_08 (ZCZ ball A17) spi0_sclk */ + P1_08_default_pin: pinmux_P1_08_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_sclk.spi0_sclk */ + P1_08_gpio_pin: pinmux_P1_08_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P1_08_gpio_pu_pin: pinmux_P1_08_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P1_08_gpio_pd_pin: pinmux_P1_08_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P1_08_gpio_input_pin: pinmux_P1_08_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_INPUT | MUX_MODE7) >; }; /* spi0_sclk.gpio0_2 */ + P1_08_spi_sclk_pin: pinmux_P1_08_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_sclk.spi0_sclk */ + P1_08_uart_pin: pinmux_P1_08_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_sclk.uart2_rxd */ + P1_08_i2c_pin: pinmux_P1_08_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_sclk.i2c2_sda */ + P1_08_pwm_pin: pinmux_P1_08_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_sclk.ehrpwm0a */ + P1_08_pru_uart_pin: pinmux_P1_08_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0950, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_sclk.pr1_uart0_cts_n */ + + /* P1_09 (ZCZ ball R18) USB1-DN */ + + /* P1_10 (ZCZ ball B17) spi0_d0 */ + P1_10_default_pin: pinmux_P1_10_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d0.spi0_d0 */ + P1_10_gpio_pin: pinmux_P1_10_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P1_10_gpio_pu_pin: pinmux_P1_10_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P1_10_gpio_pd_pin: pinmux_P1_10_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P1_10_gpio_input_pin: pinmux_P1_10_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d0.gpio0_3 */ + P1_10_spi_pin: pinmux_P1_10_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d0.spi0_d0 */ + P1_10_uart_pin: pinmux_P1_10_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* spi0_d0.uart2_txd */ + P1_10_i2c_pin: pinmux_P1_10_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d0.i2c2_scl */ + P1_10_pwm_pin: pinmux_P1_10_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d0.ehrpwm0b */ + P1_10_pru_uart_pin: pinmux_P1_10_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0954, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d0.pr1_uart0_rts_n */ + + /* P1_11 (ZCZ ball R17) USB1-DP */ + + /* P1_12 (ZCZ ball B16) spi0_d1 */ + P1_12_default_pin: pinmux_P1_12_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d1.spi0_d1 */ + P1_12_gpio_pin: pinmux_P1_12_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P1_12_gpio_pu_pin: pinmux_P1_12_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P1_12_gpio_pd_pin: pinmux_P1_12_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P1_12_gpio_input_pin: pinmux_P1_12_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_INPUT | MUX_MODE7) >; }; /* spi0_d1.gpio0_4 */ + P1_12_spi_pin: pinmux_P1_12_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* spi0_d1.spi0_d1 */ + P1_12_i2c_pin: pinmux_P1_12_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* spi0_d1.i2c1_sda */ + P1_12_pwm_pin: pinmux_P1_12_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* spi0_d1.ehrpwm0_tripzone_input */ + P1_12_pru_uart_pin: pinmux_P1_12_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0958, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* spi0_d1.pr1_uart0_rxd */ + + /* P1_13 (ZCZ ball P17) USB1-ID */ + + /* P1_14 VOUT-3.3V */ + + /* P1_15 GND */ + + /* P1_16 GND */ + + /* P1_17 (ZCZ ball A9) VREFN */ + + /* P1_18 (ZCZ ball B9) VREFP */ + + /* P1_19 (ZCZ ball B6) AIN0 */ + + /* P1_20 (ZCZ ball D14) gpio0_20 */ + P1_20_default_pin: pinmux_P1_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P1_20_gpio_pin: pinmux_P1_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P1_20_gpio_pu_pin: pinmux_P1_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P1_20_gpio_pd_pin: pinmux_P1_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P1_20_gpio_input_pin: pinmux_P1_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE7) >; }; /* xdma_event_intr1.gpio0_20 */ + P1_20_pruin_pin: pinmux_P1_20_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b4, PIN_INPUT | MUX_MODE5) >; }; /* xdma_event_intr1.pru0_in16 */ + + /* P1_21 (ZCZ ball C7) AIN1 */ + + /* P1_22 GND */ + + /* P1_23 (ZCZ ball B7) AIN2 */ + + /* P1_24 VOUT-5V */ + + /* P1_25 (ZCZ ball A7) AIN3 */ + + /* P1_26 (ZCZ ball D18) i2c2_sda */ + P1_26_default_pin: pinmux_P1_26_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P1_26_gpio_pin: pinmux_P1_26_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P1_26_gpio_pu_pin: pinmux_P1_26_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P1_26_gpio_pd_pin: pinmux_P1_26_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P1_26_gpio_input_pin: pinmux_P1_26_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_INPUT | MUX_MODE7) >; }; /* uart1_ctsn.gpio0_12 */ + P1_26_can_pin: pinmux_P1_26_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_ctsn.dcan0_tx */ + P1_26_i2c_pin: pinmux_P1_26_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_ctsn.i2c2_sda */ + P1_26_spi_cs_pin: pinmux_P1_26_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_ctsn.spi1_cs0 */ + P1_26_pru_uart_pin: pinmux_P1_26_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0978, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_ctsn.pr1_uart0_cts_n */ + + /* P1_27 (ZCZ ball C8) AIN4 */ + + /* P1_28 (ZCZ ball D17) i2c2_scl */ + P1_28_default_pin: pinmux_P1_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P1_28_gpio_pin: pinmux_P1_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P1_28_gpio_pu_pin: pinmux_P1_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P1_28_gpio_pd_pin: pinmux_P1_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P1_28_gpio_input_pin: pinmux_P1_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rtsn.gpio0_13 */ + P1_28_can_pin: pinmux_P1_28_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rtsn.dcan0_rx */ + P1_28_i2c_pin: pinmux_P1_28_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rtsn.i2c2_scl */ + P1_28_spi_cs_pin: pinmux_P1_28_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart1_rtsn.spi1_cs1 */ + P1_28_pru_uart_pin: pinmux_P1_28_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x097c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rtsn.pr1_uart0_rts_n */ + + /* P1_29 (ZCZ ball A14) pru0_in7 */ + P1_29_default_pin: pinmux_P1_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkx.pru0_in7 */ + P1_29_gpio_pin: pinmux_P1_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P1_29_gpio_pu_pin: pinmux_P1_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P1_29_gpio_pd_pin: pinmux_P1_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P1_29_gpio_input_pin: pinmux_P1_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkx.gpio3_21 */ + P1_29_qep_pin: pinmux_P1_29_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkx.eqep0_strobe */ + P1_29_pruout_pin: pinmux_P1_29_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkx.pru0_out7 */ + P1_29_pruin_pin: pinmux_P1_29_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09ac, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkx.pru0_in7 */ + + /* P1_30 (ZCZ ball E16) uart0_txd */ + P1_30_default_pin: pinmux_P1_30_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart0_txd.uart0_txd */ + P1_30_gpio_pin: pinmux_P1_30_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart0_txd.gpio1_11 */ + P1_30_gpio_pu_pin: pinmux_P1_30_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart0_txd.gpio1_11 */ + P1_30_gpio_pd_pin: pinmux_P1_30_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart0_txd.gpio1_11 */ + P1_30_gpio_input_pin: pinmux_P1_30_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_INPUT | MUX_MODE7) >; }; /* uart0_txd.gpio1_11 */ + P1_30_uart_pin: pinmux_P1_30_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart0_txd.uart0_txd */ + P1_30_spi_cs_pin: pinmux_P1_30_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart0_txd.spi1_cs1 */ + P1_30_can_pin: pinmux_P1_30_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart0_txd.dcan0_rx */ + P1_30_i2c_pin: pinmux_P1_30_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart0_txd.i2c2_scl */ + P1_30_pruout_pin: pinmux_P1_30_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* uart0_txd.pru1_out15 */ + P1_30_pruin_pin: pinmux_P1_30_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0974, PIN_INPUT | MUX_MODE6) >; }; /* uart0_txd.pru1_in15 */ + + /* P1_31 (ZCZ ball B12) pru0_in4 */ + P1_31_default_pin: pinmux_P1_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkr.pru0_in4 */ + P1_31_gpio_pin: pinmux_P1_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P1_31_gpio_pu_pin: pinmux_P1_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P1_31_gpio_pd_pin: pinmux_P1_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P1_31_gpio_input_pin: pinmux_P1_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkr.gpio3_18 */ + P1_31_qep_pin: pinmux_P1_31_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkr.eqep0a_in */ + P1_31_pruout_pin: pinmux_P1_31_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkr.pru0_out4 */ + P1_31_pruin_pin: pinmux_P1_31_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a0, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkr.pru0_in4 */ + + /* P1_32 (ZCZ ball E15) uart0_rxd */ + P1_32_default_pin: pinmux_P1_32_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart0_rxd.uart0_rxd */ + P1_32_gpio_pin: pinmux_P1_32_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart0_rxd.gpio1_10 */ + P1_32_gpio_pu_pin: pinmux_P1_32_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart0_rxd.gpio1_10 */ + P1_32_gpio_pd_pin: pinmux_P1_32_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart0_rxd.gpio1_10 */ + P1_32_gpio_input_pin: pinmux_P1_32_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_INPUT | MUX_MODE7) >; }; /* uart0_rxd.gpio1_10 */ + P1_32_uart_pin: pinmux_P1_32_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart0_rxd.uart0_rxd */ + P1_32_spi_cs_pin: pinmux_P1_32_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart0_rxd.spi1_cs0 */ + P1_32_can_pin: pinmux_P1_32_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart0_rxd.dcan0_tx */ + P1_32_i2c_pin: pinmux_P1_32_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart0_rxd.i2c2_sda */ + P1_32_pruout_pin: pinmux_P1_32_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* uart0_rxd.pru1_out14 */ + P1_32_pruin_pin: pinmux_P1_32_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0970, PIN_INPUT | MUX_MODE6) >; }; /* uart0_rxd.pru1_in14 */ + + /* P1_33 (ZCZ ball B13) pru0_in1 */ + P1_33_default_pin: pinmux_P1_33_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsx.pru0_in1 */ + P1_33_gpio_pin: pinmux_P1_33_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P1_33_gpio_pu_pin: pinmux_P1_33_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P1_33_gpio_pd_pin: pinmux_P1_33_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P1_33_gpio_input_pin: pinmux_P1_33_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsx.gpio3_15 */ + P1_33_pwm_pin: pinmux_P1_33_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsx.ehrpwm0b */ + P1_33_spi_pin: pinmux_P1_33_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_fsx.spi1_d0 */ + P1_33_pruout_pin: pinmux_P1_33_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsx.pru0_out1 */ + P1_33_pruin_pin: pinmux_P1_33_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0994, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsx.pru0_in1 */ + + /* P1_34 (ZCZ ball T11) gpio0_26 */ + P1_34_default_pin: pinmux_P1_34_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P1_34_gpio_pin: pinmux_P1_34_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P1_34_gpio_pu_pin: pinmux_P1_34_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P1_34_gpio_pd_pin: pinmux_P1_34_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P1_34_gpio_input_pin: pinmux_P1_34_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad10.gpio0_26 */ + P1_34_pwm_pin: pinmux_P1_34_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0828, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad10.ehrpwm2_tripzone_input */ + + /* P1_35 (ZCZ ball V5) pru1_in10 */ + P1_35_default_pin: pinmux_P1_35_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_pclk.pru1_in10 */ + P1_35_gpio_pin: pinmux_P1_35_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P1_35_gpio_pu_pin: pinmux_P1_35_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P1_35_gpio_pd_pin: pinmux_P1_35_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P1_35_gpio_input_pin: pinmux_P1_35_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE7) >; }; /* lcd_pclk.gpio2_24 */ + P1_35_pruout_pin: pinmux_P1_35_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_pclk.pru1_out10 */ + P1_35_pruin_pin: pinmux_P1_35_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e8, PIN_INPUT | MUX_MODE6) >; }; /* lcd_pclk.pru1_in10 */ + + /* P1_36 (ZCZ ball A13) ehrpwm0a */ + P1_36_default_pin: pinmux_P1_36_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkx.ehrpwm0a */ + P1_36_gpio_pin: pinmux_P1_36_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P1_36_gpio_pu_pin: pinmux_P1_36_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P1_36_gpio_pd_pin: pinmux_P1_36_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P1_36_gpio_input_pin: pinmux_P1_36_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_aclkx.gpio3_14 */ + P1_36_pwm_pin: pinmux_P1_36_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_aclkx.ehrpwm0a */ + P1_36_spi_sclk_pin: pinmux_P1_36_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_aclkx.spi1_sclk */ + P1_36_pruout_pin: pinmux_P1_36_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_aclkx.pru0_out0 */ + P1_36_pruin_pin: pinmux_P1_36_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0990, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_aclkx.pru0_in0 */ + + + /************************/ + /* P2 Header */ + /************************/ + + /* P2_01 (ZCZ ball U14) ehrpwm1a */ + P2_01_default_pin: pinmux_P2_01_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a2.ehrpwm1a */ + P2_01_gpio_pin: pinmux_P2_01_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P2_01_gpio_pu_pin: pinmux_P2_01_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P2_01_gpio_pd_pin: pinmux_P2_01_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P2_01_gpio_input_pin: pinmux_P2_01_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a2.gpio1_18 */ + P2_01_pwm_pin: pinmux_P2_01_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0848, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a2.ehrpwm1a */ + + /* P2_02 (ZCZ ball V17) gpio1_27 */ + P2_02_default_pin: pinmux_P2_02_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x086c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a11.gpio1_27 */ + P2_02_gpio_pin: pinmux_P2_02_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x086c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a11.gpio1_27 */ + P2_02_gpio_pu_pin: pinmux_P2_02_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x086c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a11.gpio1_27 */ + P2_02_gpio_pd_pin: pinmux_P2_02_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x086c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a11.gpio1_27 */ + P2_02_gpio_input_pin: pinmux_P2_02_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x086c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a11.gpio1_27 */ + + /* P2_03 (ZCZ ball T10) gpio0_23 */ + P2_03_default_pin: pinmux_P2_03_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P2_03_gpio_pin: pinmux_P2_03_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P2_03_gpio_pu_pin: pinmux_P2_03_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P2_03_gpio_pd_pin: pinmux_P2_03_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P2_03_gpio_input_pin: pinmux_P2_03_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad9.gpio0_23 */ + P2_03_pwm_pin: pinmux_P2_03_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0824, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad9.ehrpwm2b */ + + /* P2_04 (ZCZ ball T16) gpio1_26 */ + P2_04_default_pin: pinmux_P2_04_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0868, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a10.gpio1_26 */ + P2_04_gpio_pin: pinmux_P2_04_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0868, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a10.gpio1_26 */ + P2_04_gpio_pu_pin: pinmux_P2_04_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0868, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a10.gpio1_26 */ + P2_04_gpio_pd_pin: pinmux_P2_04_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0868, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a10.gpio1_26 */ + P2_04_gpio_input_pin: pinmux_P2_04_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0868, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a10.gpio1_26 */ + + /* P2_05 (ZCZ ball T17) uart4_rxd */ + P2_05_default_pin: pinmux_P2_05_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wait0.uart4_rxd */ + P2_05_gpio_pin: pinmux_P2_05_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P2_05_gpio_pu_pin: pinmux_P2_05_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P2_05_gpio_pd_pin: pinmux_P2_05_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P2_05_gpio_input_pin: pinmux_P2_05_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wait0.gpio0_30 */ + P2_05_uart_pin: pinmux_P2_05_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0870, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wait0.uart4_rxd */ + + /* P2_06 (ZCZ ball U16) gpio1_25 */ + P2_06_default_pin: pinmux_P2_06_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0864, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a9.gpio1_25 */ + P2_06_gpio_pin: pinmux_P2_06_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0864, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a9.gpio1_25 */ + P2_06_gpio_pu_pin: pinmux_P2_06_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0864, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a9.gpio1_25 */ + P2_06_gpio_pd_pin: pinmux_P2_06_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0864, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a9.gpio1_25 */ + P2_06_gpio_input_pin: pinmux_P2_06_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0864, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a9.gpio1_25 */ + + /* P2_07 (ZCZ ball U17) uart4_txd */ + P2_07_default_pin: pinmux_P2_07_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wpn.uart4_txd */ + P2_07_gpio_pin: pinmux_P2_07_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P2_07_gpio_pu_pin: pinmux_P2_07_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P2_07_gpio_pd_pin: pinmux_P2_07_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P2_07_gpio_input_pin: pinmux_P2_07_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_wpn.gpio0_31 */ + P2_07_uart_pin: pinmux_P2_07_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0874, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_wpn.uart4_txd */ + + /* P2_08 (ZCZ ball U18) gpio1_28 */ + P2_08_default_pin: pinmux_P2_08_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P2_08_gpio_pin: pinmux_P2_08_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P2_08_gpio_pu_pin: pinmux_P2_08_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P2_08_gpio_pd_pin: pinmux_P2_08_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + P2_08_gpio_input_pin: pinmux_P2_08_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0878, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_be1n.gpio1_28 */ + + /* P2_09 (ZCZ ball D15) i2c1_scl */ + P2_09_default_pin: pinmux_P2_09_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_txd.i2c1_scl */ + P2_09_gpio_pin: pinmux_P2_09_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P2_09_gpio_pu_pin: pinmux_P2_09_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P2_09_gpio_pd_pin: pinmux_P2_09_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P2_09_gpio_input_pin: pinmux_P2_09_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE7) >; }; /* uart1_txd.gpio0_15 */ + P2_09_uart_pin: pinmux_P2_09_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_txd.uart1_txd */ + P2_09_can_pin: pinmux_P2_09_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart1_txd.dcan1_rx */ + P2_09_i2c_pin: pinmux_P2_09_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_txd.i2c1_scl */ + P2_09_pru_uart_pin: pinmux_P2_09_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_txd.pr1_uart0_txd */ + P2_09_pruin_pin: pinmux_P2_09_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0984, PIN_INPUT | MUX_MODE6) >; }; /* uart1_txd.pru0_in16 */ + + /* P2_10 (ZCZ ball R14) gpio1_20 */ + P2_10_default_pin: pinmux_P2_10_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a4.gpio1_20 */ + P2_10_gpio_pin: pinmux_P2_10_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a4.gpio1_20 */ + P2_10_gpio_pu_pin: pinmux_P2_10_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a4.gpio1_20 */ + P2_10_gpio_pd_pin: pinmux_P2_10_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_a4.gpio1_20 */ + P2_10_gpio_input_pin: pinmux_P2_10_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_a4.gpio1_20 */ + P2_10_qep_pin: pinmux_P2_10_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0850, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE6) >; }; /* gpmc_a4.eqep1a_in */ + + /* P2_11 (ZCZ ball D16) i2c1_sda */ + P2_11_default_pin: pinmux_P2_11_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rxd.i2c1_sda */ + P2_11_gpio_pin: pinmux_P2_11_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P2_11_gpio_pu_pin: pinmux_P2_11_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P2_11_gpio_pd_pin: pinmux_P2_11_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P2_11_gpio_input_pin: pinmux_P2_11_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE7) >; }; /* uart1_rxd.gpio0_14 */ + P2_11_uart_pin: pinmux_P2_11_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE0) >; }; /* uart1_rxd.uart1_rxd */ + P2_11_can_pin: pinmux_P2_11_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart1_rxd.dcan1_tx */ + P2_11_i2c_pin: pinmux_P2_11_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart1_rxd.i2c1_sda */ + P2_11_pru_uart_pin: pinmux_P2_11_pru_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart1_rxd.pr1_uart0_rxd */ + P2_11_pruin_pin: pinmux_P2_11_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0980, PIN_INPUT | MUX_MODE6) >; }; /* uart1_rxd.pru1_in16 */ + + /* P2_12 POWER_BUTTON */ + + /* P2_13 VOUT-5V */ + + /* P2_14 BAT-VIN */ + + /* P2_15 GND */ + + /* P2_16 BAT-TEMP */ + + /* P2_17 (ZCZ ball V12) gpio2_1 */ + P2_17_default_pin: pinmux_P2_17_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P2_17_gpio_pin: pinmux_P2_17_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P2_17_gpio_pu_pin: pinmux_P2_17_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P2_17_gpio_pd_pin: pinmux_P2_17_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + P2_17_gpio_input_pin: pinmux_P2_17_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x088c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_clk.gpio2_1 */ + + /* P2_18 (ZCZ ball U13) gpio1_15 */ + P2_18_default_pin: pinmux_P2_18_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P2_18_gpio_pin: pinmux_P2_18_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P2_18_gpio_pu_pin: pinmux_P2_18_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P2_18_gpio_pd_pin: pinmux_P2_18_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P2_18_gpio_input_pin: pinmux_P2_18_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad15.gpio1_15 */ + P2_18_qep_pin: pinmux_P2_18_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad15.eqep2_strobe */ + P2_18_pru_ecap_pin: pinmux_P2_18_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* gpmc_ad15.pr1_ecap0_ecap_capin_apwm_o */ + P2_18_pruin_pin: pinmux_P2_18_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x083c, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad15.pru0_in15 */ + + /* P2_19 (ZCZ ball U12) gpio0_27 */ + P2_19_default_pin: pinmux_P2_19_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P2_19_gpio_pin: pinmux_P2_19_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P2_19_gpio_pu_pin: pinmux_P2_19_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P2_19_gpio_pd_pin: pinmux_P2_19_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P2_19_gpio_input_pin: pinmux_P2_19_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad11.gpio0_27 */ + P2_19_pwm_pin: pinmux_P2_19_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x082c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad11.ehrpwm0_synco */ + + /* P2_20 (ZCZ ball T13) gpio2_0 */ + P2_20_default_pin: pinmux_P2_20_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0888, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn3.gpio2_0 */ + P2_20_gpio_pin: pinmux_P2_20_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0888, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn3.gpio2_0 */ + P2_20_gpio_pu_pin: pinmux_P2_20_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0888, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn3.gpio2_0 */ + P2_20_gpio_pd_pin: pinmux_P2_20_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0888, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_csn3.gpio2_0 */ + P2_20_gpio_input_pin: pinmux_P2_20_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0888, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_csn3.gpio2_0 */ + + /* P2_21 GND */ + + /* P2_22 (ZCZ ball V13) gpio1_14 */ + P2_22_default_pin: pinmux_P2_22_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P2_22_gpio_pin: pinmux_P2_22_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P2_22_gpio_pu_pin: pinmux_P2_22_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P2_22_gpio_pd_pin: pinmux_P2_22_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P2_22_gpio_input_pin: pinmux_P2_22_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad14.gpio1_14 */ + P2_22_qep_pin: pinmux_P2_22_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad14.eqep2_index */ + P2_22_pruin_pin: pinmux_P2_22_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0838, PIN_INPUT | MUX_MODE6) >; }; /* gpmc_ad14.pru0_in14 */ + + /* P2_23 VOUT-3.3V */ + + /* P2_24 (ZCZ ball T12) gpio1_12 */ + P2_24_default_pin: pinmux_P2_24_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P2_24_gpio_pin: pinmux_P2_24_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P2_24_gpio_pu_pin: pinmux_P2_24_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P2_24_gpio_pd_pin: pinmux_P2_24_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P2_24_gpio_input_pin: pinmux_P2_24_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad12.gpio1_12 */ + P2_24_qep_pin: pinmux_P2_24_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad12.eqep2a_in */ + P2_24_pruout_pin: pinmux_P2_24_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0830, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad12.pru0_out14 */ + + /* P2_25 (ZCZ ball E17) spi1_d1 */ + P2_25_default_pin: pinmux_P2_25_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart0_rtsn.spi1_d1 */ + P2_25_gpio_pin: pinmux_P2_25_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart0_rtsn.gpio1_9 */ + P2_25_gpio_pu_pin: pinmux_P2_25_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart0_rtsn.gpio1_9 */ + P2_25_gpio_pd_pin: pinmux_P2_25_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart0_rtsn.gpio1_9 */ + P2_25_gpio_input_pin: pinmux_P2_25_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_INPUT | MUX_MODE7) >; }; /* uart0_rtsn.gpio1_9 */ + P2_25_uart_pin: pinmux_P2_25_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart0_rtsn.uart4_txd */ + P2_25_can_pin: pinmux_P2_25_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_INPUT_PULLUP | MUX_MODE2) >; }; /* uart0_rtsn.dcan1_rx */ + P2_25_i2c_pin: pinmux_P2_25_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart0_rtsn.i2c1_scl */ + P2_25_spi_pin: pinmux_P2_25_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart0_rtsn.spi1_d1 */ + P2_25_spi_cs_pin: pinmux_P2_25_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x096c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE5) >; }; /* uart0_rtsn.spi1_cs0 */ + + /* P2_26 RESET# */ + + /* P2_27 (ZCZ ball E18) spi1_d0 */ + P2_27_default_pin: pinmux_P2_27_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart0_ctsn.spi1_d0 */ + P2_27_gpio_pin: pinmux_P2_27_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* uart0_ctsn.gpio1_8 */ + P2_27_gpio_pu_pin: pinmux_P2_27_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* uart0_ctsn.gpio1_8 */ + P2_27_gpio_pd_pin: pinmux_P2_27_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* uart0_ctsn.gpio1_8 */ + P2_27_gpio_input_pin: pinmux_P2_27_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_INPUT | MUX_MODE7) >; }; /* uart0_ctsn.gpio1_8 */ + P2_27_uart_pin: pinmux_P2_27_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* uart0_ctsn.uart4_rxd */ + P2_27_can_pin: pinmux_P2_27_can_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | MUX_MODE2) >; }; /* uart0_ctsn.dcan1_tx */ + P2_27_i2c_pin: pinmux_P2_27_i2c_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* uart0_ctsn.i2c1_sda */ + P2_27_spi_pin: pinmux_P2_27_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0968, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* uart0_ctsn.spi1_d0 */ + + /* P2_28 (ZCZ ball D13) pru0_in6 */ + P2_28_default_pin: pinmux_P2_28_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr1.pru0_in6 */ + P2_28_gpio_pin: pinmux_P2_28_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P2_28_gpio_pu_pin: pinmux_P2_28_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P2_28_gpio_pd_pin: pinmux_P2_28_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P2_28_gpio_input_pin: pinmux_P2_28_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_axr1.gpio3_20 */ + P2_28_qep_pin: pinmux_P2_28_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_axr1.eqep0_index */ + P2_28_pruout_pin: pinmux_P2_28_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_axr1.pru0_out6 */ + P2_28_pruin_pin: pinmux_P2_28_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a8, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr1.pru0_in6 */ + + /* P2_29 (ZCZ ball C18) spi1_sclk */ + P2_29_default_pin: pinmux_P2_29_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* eCAP0_in_PWM0_out.spi1_sclk */ + P2_29_gpio_pin: pinmux_P2_29_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P2_29_gpio_pu_pin: pinmux_P2_29_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P2_29_gpio_pd_pin: pinmux_P2_29_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P2_29_gpio_input_pin: pinmux_P2_29_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_INPUT | MUX_MODE7) >; }; /* eCAP0_in_PWM0_out.gpio0_7 */ + P2_29_pwm_pin: pinmux_P2_29_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE0) >; }; /* eCAP0_in_PWM0_out.ecap0_in_pwm0_out */ + P2_29_uart_pin: pinmux_P2_29_uart_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* eCAP0_in_PWM0_out.uart3_txd */ + P2_29_spi_cs_pin: pinmux_P2_29_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE2) >; }; /* eCAP0_in_PWM0_out.spi1_cs1 */ + P2_29_pru_ecap_pin: pinmux_P2_29_pru_ecap_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE3) >; }; /* eCAP0_in_PWM0_out.pr1_ecap0_ecap_capin_apwm_o */ + P2_29_spi_sclk_pin: pinmux_P2_29_spi_sclk_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0964, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* eCAP0_in_PWM0_out.spi1_sclk */ + + /* P2_30 (ZCZ ball C12) pru0_in3 */ + P2_30_default_pin: pinmux_P2_30_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkr.pru0_in3 */ + P2_30_gpio_pin: pinmux_P2_30_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P2_30_gpio_pu_pin: pinmux_P2_30_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P2_30_gpio_pd_pin: pinmux_P2_30_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P2_30_gpio_input_pin: pinmux_P2_30_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_ahclkr.gpio3_17 */ + P2_30_pwm_pin: pinmux_P2_30_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_ahclkr.ehrpwm0_synci */ + P2_30_spi_cs_pin: pinmux_P2_30_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_ahclkr.spi1_cs0 */ + P2_30_pruout_pin: pinmux_P2_30_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_ahclkr.pru0_out3 */ + P2_30_pruin_pin: pinmux_P2_30_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x099c, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_ahclkr.pru0_in3 */ + + /* P2_31 (ZCZ ball A15) spi1_cs1 */ + P2_31_default_pin: pinmux_P2_31_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* xdma_event_intr0.spi1_cs1 */ + P2_31_gpio_pin: pinmux_P2_31_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr0.gpio0_19 */ + P2_31_gpio_pu_pin: pinmux_P2_31_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr0.gpio0_19 */ + P2_31_gpio_pd_pin: pinmux_P2_31_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* xdma_event_intr0.gpio0_19 */ + P2_31_gpio_input_pin: pinmux_P2_31_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_INPUT | MUX_MODE7) >; }; /* xdma_event_intr0.gpio0_19 */ + P2_31_spi_cs_pin: pinmux_P2_31_spi_cs_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* xdma_event_intr0.spi1_cs1 */ + P2_31_pruin_pin: pinmux_P2_31_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09b0, PIN_INPUT | MUX_MODE5) >; }; /* xdma_event_intr0.pru1_in16 */ + + /* P2_32 (ZCZ ball D12) pru0_in2 */ + P2_32_default_pin: pinmux_P2_32_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr0.pru0_in2 */ + P2_32_gpio_pin: pinmux_P2_32_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P2_32_gpio_pu_pin: pinmux_P2_32_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P2_32_gpio_pd_pin: pinmux_P2_32_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P2_32_gpio_input_pin: pinmux_P2_32_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_axr0.gpio3_16 */ + P2_32_pwm_pin: pinmux_P2_32_pwm_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_axr0.ehrpwm0_tripzone_input */ + P2_32_spi_pin: pinmux_P2_32_spi_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE3) >; }; /* mcasp0_axr0.spi1_d1 */ + P2_32_pruout_pin: pinmux_P2_32_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_axr0.pru0_out2 */ + P2_32_pruin_pin: pinmux_P2_32_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0998, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_axr0.pru0_in2 */ + + /* P2_33 (ZCZ ball R12) gpio1_13 */ + P2_33_default_pin: pinmux_P2_33_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P2_33_gpio_pin: pinmux_P2_33_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P2_33_gpio_pu_pin: pinmux_P2_33_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P2_33_gpio_pd_pin: pinmux_P2_33_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P2_33_gpio_input_pin: pinmux_P2_33_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_INPUT | MUX_MODE7) >; }; /* gpmc_ad13.gpio1_13 */ + P2_33_qep_pin: pinmux_P2_33_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE4) >; }; /* gpmc_ad13.eqep2b_in */ + P2_33_pruout_pin: pinmux_P2_33_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x0834, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE6) >; }; /* gpmc_ad13.pru0_out15 */ + + /* P2_34 (ZCZ ball C13) pru0_in5 */ + P2_34_default_pin: pinmux_P2_34_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsr.pru0_in5 */ + P2_34_gpio_pin: pinmux_P2_34_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P2_34_gpio_pu_pin: pinmux_P2_34_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P2_34_gpio_pd_pin: pinmux_P2_34_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P2_34_gpio_input_pin: pinmux_P2_34_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE7) >; }; /* mcasp0_fsr.gpio3_19 */ + P2_34_qep_pin: pinmux_P2_34_qep_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE1) >; }; /* mcasp0_fsr.eqep0b_in */ + P2_34_pruout_pin: pinmux_P2_34_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* mcasp0_fsr.pru0_out5 */ + P2_34_pruin_pin: pinmux_P2_34_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x09a4, PIN_INPUT | MUX_MODE6) >; }; /* mcasp0_fsr.pru0_in5 */ + + /* P2_35 (ZCZ ball U5) gpio2_22 */ + P2_35_default_pin: pinmux_P2_35_default_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P2_35_gpio_pin: pinmux_P2_35_gpio_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P2_35_gpio_pu_pin: pinmux_P2_35_gpio_pu_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLUP | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P2_35_gpio_pd_pin: pinmux_P2_35_gpio_pd_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P2_35_gpio_input_pin: pinmux_P2_35_gpio_input_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE7) >; }; /* lcd_vsync.gpio2_22 */ + P2_35_pruout_pin: pinmux_P2_35_pruout_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_OUTPUT_PULLDOWN | INPUT_EN | MUX_MODE5) >; }; /* lcd_vsync.pru1_out8 */ + P2_35_pruin_pin: pinmux_P2_35_pruin_pin { pinctrl-single,pins = < + AM33XX_IOPAD(0x08e0, PIN_INPUT | MUX_MODE6) >; }; /* lcd_vsync.pru1_in8 */ + + /* P2_36 (ZCZ ball C9) AIN7 */ }; &epwmss0 { @@ -140,7 +969,8 @@ &ehrpwm0 { status = "okay"; pinctrl-names = "default"; - pinctrl-0 = <&ehrpwm0_pins>; + //pinctrl-0 = <&ehrpwm0_pins>; + pinctrl-0 = <>; }; &epwmss1 { @@ -150,7 +980,18 @@ &ehrpwm1 { status = "okay"; pinctrl-names = "default"; - pinctrl-0 = <&ehrpwm1_pins>; + //pinctrl-0 = <&ehrpwm1_pins>; + pinctrl-0 = <>; +}; + +&epwmss2 { + status = "okay"; +}; + +&ehrpwm2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; }; &i2c0 { @@ -160,9 +1001,18 @@ }; }; +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <>; + + status = "okay"; + clock-frequency = <400000>; +}; + &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&i2c2_pins>; +// pinctrl-0 = <&i2c2_pins>; + pinctrl-0 = <>; status = "okay"; clock-frequency = <400000>; @@ -193,14 +1043,30 @@ &uart0 { pinctrl-names = "default"; - pinctrl-0 = <&uart0_pins>; + //pinctrl-0 = <&uart0_pins>; + pinctrl-0 = <>; + + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <>; + + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <>; status = "okay"; }; &uart4 { pinctrl-names = "default"; - pinctrl-0 = <&uart4_pins>; + //pinctrl-0 = <&uart4_pins>; + pinctrl-0 = <>; status = "okay"; }; @@ -234,3 +1100,1092 @@ &cppi41dma { status = "okay"; }; + +&spi0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/0.0"; + reg = <0>; + spi-max-frequency = <24000000>; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/0.1"; + reg = <1>; + spi-max-frequency = <24000000>; + status = "disabled"; + }; +}; + +&spi1 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + channel@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/1.0"; + reg = <0>; + spi-max-frequency = <24000000>; + }; + + channel@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "spidev"; + symlink = "spi/1.1"; + reg = <1>; + spi-max-frequency = <24000000>; + }; +}; + +&dcan0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&dcan1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; +}; + +&ocp { + /************************/ + /* P1 Header */ + /************************/ + + /* P1_01 VIN-AC */ + + /* P1_02 (ZCZ ball R5) gpio_input */ + P1_02_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P1_02_default_pin>; + pinctrl-1 = <&P1_02_gpio_pin>; + pinctrl-2 = <&P1_02_gpio_pu_pin>; + pinctrl-3 = <&P1_02_gpio_pd_pin>; + pinctrl-4 = <&P1_02_gpio_input_pin>; + pinctrl-5 = <&P1_02_pruout_pin>; + pinctrl-6 = <&P1_02_pruin_pin>; + }; + + /* P1_03 (ZCZ ball F15) usb1_vbus_out */ + + /* P1_04 (ZCZ ball R6) */ + P1_04_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P1_04_default_pin>; + pinctrl-1 = <&P1_04_gpio_pin>; + pinctrl-2 = <&P1_04_gpio_pu_pin>; + pinctrl-3 = <&P1_04_gpio_pd_pin>; + pinctrl-4 = <&P1_04_gpio_input_pin>; + pinctrl-5 = <&P1_04_pruout_pin>; + pinctrl-6 = <&P1_04_pruin_pin>; + }; + + /* P1_05 (ZCZ ball T18) usb1_vbus_in */ + + /* P1_06 (ZCZ ball A16) spi_cs */ + P1_06_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P1_06_default_pin>; + pinctrl-1 = <&P1_06_gpio_pin>; + pinctrl-2 = <&P1_06_gpio_pu_pin>; + pinctrl-3 = <&P1_06_gpio_pd_pin>; + pinctrl-4 = <&P1_06_gpio_input_pin>; + pinctrl-5 = <&P1_06_spi_cs_pin>; + pinctrl-6 = <&P1_06_i2c_pin>; + pinctrl-7 = <&P1_06_pwm_pin>; + pinctrl-8 = <&P1_06_pru_uart_pin>; + }; + + /* P1_07 VIN-USB */ + + /* P1_08 (ZCZ ball A17) spi_sclk */ + P1_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P1_08_default_pin>; + pinctrl-1 = <&P1_08_gpio_pin>; + pinctrl-2 = <&P1_08_gpio_pu_pin>; + pinctrl-3 = <&P1_08_gpio_pd_pin>; + pinctrl-4 = <&P1_08_gpio_input_pin>; + pinctrl-5 = <&P1_08_spi_sclk_pin>; + pinctrl-6 = <&P1_08_uart_pin>; + pinctrl-7 = <&P1_08_i2c_pin>; + pinctrl-8 = <&P1_08_pwm_pin>; + pinctrl-9 = <&P1_08_pru_uart_pin>; + }; + + /* P1_09 (ZCZ ball R18) USB1-DN */ + + /* P1_10 (ZCZ ball B17) spi */ + P1_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "uart", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P1_10_default_pin>; + pinctrl-1 = <&P1_10_gpio_pin>; + pinctrl-2 = <&P1_10_gpio_pu_pin>; + pinctrl-3 = <&P1_10_gpio_pd_pin>; + pinctrl-4 = <&P1_10_gpio_input_pin>; + pinctrl-5 = <&P1_10_spi_pin>; + pinctrl-6 = <&P1_10_uart_pin>; + pinctrl-7 = <&P1_10_i2c_pin>; + pinctrl-8 = <&P1_10_pwm_pin>; + pinctrl-9 = <&P1_10_pru_uart_pin>; + }; + + /* P1_11 (ZCZ ball R17) USB1-DP */ + + /* P1_12 (ZCZ ball B16) spi */ + P1_12_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "i2c", "pwm", "pru_uart"; + pinctrl-0 = <&P1_12_default_pin>; + pinctrl-1 = <&P1_12_gpio_pin>; + pinctrl-2 = <&P1_12_gpio_pu_pin>; + pinctrl-3 = <&P1_12_gpio_pd_pin>; + pinctrl-4 = <&P1_12_gpio_input_pin>; + pinctrl-5 = <&P1_12_spi_pin>; + pinctrl-6 = <&P1_12_i2c_pin>; + pinctrl-7 = <&P1_12_pwm_pin>; + pinctrl-8 = <&P1_12_pru_uart_pin>; + }; + + /* P1_13 (ZCZ ball P17) USB1-ID */ + + /* P1_14 VOUT-3.3V */ + + /* P1_15 GND */ + + /* P1_16 GND */ + + /* P1_17 (ZCZ ball A9) VREFN */ + + /* P1_18 (ZCZ ball B9) VREFP */ + + /* P1_19 (ZCZ ball B6) AIN0 */ + + /* P1_20 (ZCZ ball D14) */ + P1_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruin"; + pinctrl-0 = <&P1_20_default_pin>; + pinctrl-1 = <&P1_20_gpio_pin>; + pinctrl-2 = <&P1_20_gpio_pu_pin>; + pinctrl-3 = <&P1_20_gpio_pd_pin>; + pinctrl-4 = <&P1_20_gpio_input_pin>; + pinctrl-5 = <&P1_20_pruin_pin>; + }; + + /* P1_21 (ZCZ ball C7) AIN1 */ + + /* P1_22 GND */ + + /* P1_23 (ZCZ ball B7) AIN2 */ + + /* P1_24 VOUT-5V */ + + /* P1_25 (ZCZ ball A7) AIN3 */ + + /* P1_26 (ZCZ ball D18) i2c */ + P1_26_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart"; + pinctrl-0 = <&P1_26_default_pin>; + pinctrl-1 = <&P1_26_gpio_pin>; + pinctrl-2 = <&P1_26_gpio_pu_pin>; + pinctrl-3 = <&P1_26_gpio_pd_pin>; + pinctrl-4 = <&P1_26_gpio_input_pin>; + pinctrl-5 = <&P1_26_spi_cs_pin>; + pinctrl-6 = <&P1_26_can_pin>; + pinctrl-7 = <&P1_26_i2c_pin>; + pinctrl-8 = <&P1_26_pru_uart_pin>; + }; + + /* P1_27 (ZCZ ball C8) AIN4 */ + + /* P1_28 (ZCZ ball D17) i2c */ + P1_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "can", "i2c", "pru_uart"; + pinctrl-0 = <&P1_28_default_pin>; + pinctrl-1 = <&P1_28_gpio_pin>; + pinctrl-2 = <&P1_28_gpio_pu_pin>; + pinctrl-3 = <&P1_28_gpio_pd_pin>; + pinctrl-4 = <&P1_28_gpio_input_pin>; + pinctrl-5 = <&P1_28_spi_cs_pin>; + pinctrl-6 = <&P1_28_can_pin>; + pinctrl-7 = <&P1_28_i2c_pin>; + pinctrl-8 = <&P1_28_pru_uart_pin>; + }; + + /* P1_29 (ZCZ ball A14) pruin */ + P1_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P1_29_default_pin>; + pinctrl-1 = <&P1_29_gpio_pin>; + pinctrl-2 = <&P1_29_gpio_pu_pin>; + pinctrl-3 = <&P1_29_gpio_pd_pin>; + pinctrl-4 = <&P1_29_gpio_input_pin>; + pinctrl-5 = <&P1_29_qep_pin>; + pinctrl-6 = <&P1_29_pruout_pin>; + pinctrl-7 = <&P1_29_pruin_pin>; + }; + + /* P1_30 (ZCZ ball E16) uart */ + P1_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "uart", "can", "i2c", "pruout", "pruin"; + pinctrl-0 = <&P1_30_default_pin>; + pinctrl-1 = <&P1_30_gpio_pin>; + pinctrl-2 = <&P1_30_gpio_pu_pin>; + pinctrl-3 = <&P1_30_gpio_pd_pin>; + pinctrl-4 = <&P1_30_gpio_input_pin>; + pinctrl-5 = <&P1_30_spi_cs_pin>; + pinctrl-6 = <&P1_30_uart_pin>; + pinctrl-7 = <&P1_30_can_pin>; + pinctrl-8 = <&P1_30_i2c_pin>; + pinctrl-9 = <&P1_30_pruout_pin>; + pinctrl-10 = <&P1_30_pruin_pin>; + }; + + /* P1_31 (ZCZ ball B12) pruin */ + P1_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P1_31_default_pin>; + pinctrl-1 = <&P1_31_gpio_pin>; + pinctrl-2 = <&P1_31_gpio_pu_pin>; + pinctrl-3 = <&P1_31_gpio_pd_pin>; + pinctrl-4 = <&P1_31_gpio_input_pin>; + pinctrl-5 = <&P1_31_qep_pin>; + pinctrl-6 = <&P1_31_pruout_pin>; + pinctrl-7 = <&P1_31_pruin_pin>; + }; + + /* P1_32 (ZCZ ball E15) uart */ + P1_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "uart", "can", "i2c", "pruout", "pruin"; + pinctrl-0 = <&P1_32_default_pin>; + pinctrl-1 = <&P1_32_gpio_pin>; + pinctrl-2 = <&P1_32_gpio_pu_pin>; + pinctrl-3 = <&P1_32_gpio_pd_pin>; + pinctrl-4 = <&P1_32_gpio_input_pin>; + pinctrl-5 = <&P1_32_spi_cs_pin>; + pinctrl-6 = <&P1_32_uart_pin>; + pinctrl-7 = <&P1_32_can_pin>; + pinctrl-8 = <&P1_32_i2c_pin>; + pinctrl-9 = <&P1_32_pruout_pin>; + pinctrl-10 = <&P1_32_pruin_pin>; + }; + + /* P1_33 (ZCZ ball B13) pruin */ + P1_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P1_33_default_pin>; + pinctrl-1 = <&P1_33_gpio_pin>; + pinctrl-2 = <&P1_33_gpio_pu_pin>; + pinctrl-3 = <&P1_33_gpio_pd_pin>; + pinctrl-4 = <&P1_33_gpio_input_pin>; + pinctrl-5 = <&P1_33_spi_pin>; + pinctrl-6 = <&P1_33_pwm_pin>; + pinctrl-7 = <&P1_33_pruout_pin>; + pinctrl-8 = <&P1_33_pruin_pin>; + }; + + /* P1_34 (ZCZ ball T11) */ + P1_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P1_34_default_pin>; + pinctrl-1 = <&P1_34_gpio_pin>; + pinctrl-2 = <&P1_34_gpio_pu_pin>; + pinctrl-3 = <&P1_34_gpio_pd_pin>; + pinctrl-4 = <&P1_34_gpio_input_pin>; + pinctrl-5 = <&P1_34_pwm_pin>; + }; + + /* P1_35 (ZCZ ball V5) pruin */ + P1_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P1_35_default_pin>; + pinctrl-1 = <&P1_35_gpio_pin>; + pinctrl-2 = <&P1_35_gpio_pu_pin>; + pinctrl-3 = <&P1_35_gpio_pd_pin>; + pinctrl-4 = <&P1_35_gpio_input_pin>; + pinctrl-5 = <&P1_35_pruout_pin>; + pinctrl-6 = <&P1_35_pruin_pin>; + }; + + /* P1_36 (ZCZ ball A13) pwm */ + P1_36_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_sclk", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P1_36_default_pin>; + pinctrl-1 = <&P1_36_gpio_pin>; + pinctrl-2 = <&P1_36_gpio_pu_pin>; + pinctrl-3 = <&P1_36_gpio_pd_pin>; + pinctrl-4 = <&P1_36_gpio_input_pin>; + pinctrl-5 = <&P1_36_spi_sclk_pin>; + pinctrl-6 = <&P1_36_pwm_pin>; + pinctrl-7 = <&P1_36_pruout_pin>; + pinctrl-8 = <&P1_36_pruin_pin>; + }; + + + /************************/ + /* P2 Header */ + /************************/ + + /* P2_01 (ZCZ ball U14) pwm */ + P2_01_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P2_01_default_pin>; + pinctrl-1 = <&P2_01_gpio_pin>; + pinctrl-2 = <&P2_01_gpio_pu_pin>; + pinctrl-3 = <&P2_01_gpio_pd_pin>; + pinctrl-4 = <&P2_01_gpio_input_pin>; + pinctrl-5 = <&P2_01_pwm_pin>; + }; + + /* P2_02 (ZCZ ball V17) */ + P2_02_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_02_default_pin>; + pinctrl-1 = <&P2_02_gpio_pin>; + pinctrl-2 = <&P2_02_gpio_pu_pin>; + pinctrl-3 = <&P2_02_gpio_pd_pin>; + pinctrl-4 = <&P2_02_gpio_input_pin>; + }; + + /* P2_03 (ZCZ ball T10) */ + P2_03_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P2_03_default_pin>; + pinctrl-1 = <&P2_03_gpio_pin>; + pinctrl-2 = <&P2_03_gpio_pu_pin>; + pinctrl-3 = <&P2_03_gpio_pd_pin>; + pinctrl-4 = <&P2_03_gpio_input_pin>; + pinctrl-5 = <&P2_03_pwm_pin>; + }; + + /* P2_04 (ZCZ ball T16) */ + P2_04_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_04_default_pin>; + pinctrl-1 = <&P2_04_gpio_pin>; + pinctrl-2 = <&P2_04_gpio_pu_pin>; + pinctrl-3 = <&P2_04_gpio_pd_pin>; + pinctrl-4 = <&P2_04_gpio_input_pin>; + }; + + /* P2_05 (ZCZ ball T17) uart */ + P2_05_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P2_05_default_pin>; + pinctrl-1 = <&P2_05_gpio_pin>; + pinctrl-2 = <&P2_05_gpio_pu_pin>; + pinctrl-3 = <&P2_05_gpio_pd_pin>; + pinctrl-4 = <&P2_05_gpio_input_pin>; + pinctrl-5 = <&P2_05_uart_pin>; + }; + + /* P2_06 (ZCZ ball U16) */ + P2_06_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_06_default_pin>; + pinctrl-1 = <&P2_06_gpio_pin>; + pinctrl-2 = <&P2_06_gpio_pu_pin>; + pinctrl-3 = <&P2_06_gpio_pd_pin>; + pinctrl-4 = <&P2_06_gpio_input_pin>; + }; + + /* P2_07 (ZCZ ball U17) uart */ + P2_07_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart"; + pinctrl-0 = <&P2_07_default_pin>; + pinctrl-1 = <&P2_07_gpio_pin>; + pinctrl-2 = <&P2_07_gpio_pu_pin>; + pinctrl-3 = <&P2_07_gpio_pd_pin>; + pinctrl-4 = <&P2_07_gpio_input_pin>; + pinctrl-5 = <&P2_07_uart_pin>; + }; + + /* P2_08 (ZCZ ball U18) */ + P2_08_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_08_default_pin>; + pinctrl-1 = <&P2_08_gpio_pin>; + pinctrl-2 = <&P2_08_gpio_pu_pin>; + pinctrl-3 = <&P2_08_gpio_pd_pin>; + pinctrl-4 = <&P2_08_gpio_input_pin>; + }; + + /* P2_09 (ZCZ ball D15) i2c */ + P2_09_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P2_09_default_pin>; + pinctrl-1 = <&P2_09_gpio_pin>; + pinctrl-2 = <&P2_09_gpio_pu_pin>; + pinctrl-3 = <&P2_09_gpio_pd_pin>; + pinctrl-4 = <&P2_09_gpio_input_pin>; + pinctrl-5 = <&P2_09_uart_pin>; + pinctrl-6 = <&P2_09_can_pin>; + pinctrl-7 = <&P2_09_i2c_pin>; + pinctrl-8 = <&P2_09_pru_uart_pin>; + pinctrl-9 = <&P2_09_pruin_pin>; + }; + + /* P2_10 (ZCZ ball R14) */ + P2_10_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep"; + pinctrl-0 = <&P2_10_default_pin>; + pinctrl-1 = <&P2_10_gpio_pin>; + pinctrl-2 = <&P2_10_gpio_pu_pin>; + pinctrl-3 = <&P2_10_gpio_pd_pin>; + pinctrl-4 = <&P2_10_gpio_input_pin>; + pinctrl-5 = <&P2_10_qep_pin>; + }; + + /* P2_11 (ZCZ ball D16) i2c */ + P2_11_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "uart", "can", "i2c", "pru_uart", "pruin"; + pinctrl-0 = <&P2_11_default_pin>; + pinctrl-1 = <&P2_11_gpio_pin>; + pinctrl-2 = <&P2_11_gpio_pu_pin>; + pinctrl-3 = <&P2_11_gpio_pd_pin>; + pinctrl-4 = <&P2_11_gpio_input_pin>; + pinctrl-5 = <&P2_11_uart_pin>; + pinctrl-6 = <&P2_11_can_pin>; + pinctrl-7 = <&P2_11_i2c_pin>; + pinctrl-8 = <&P2_11_pru_uart_pin>; + pinctrl-9 = <&P2_11_pruin_pin>; + }; + + /* P2_12 POWER_BUTTON */ + + /* P2_13 VOUT-5V */ + + /* P2_14 BAT-VIN */ + + /* P2_15 GND */ + + /* P2_16 BAT-TEMP */ + + /* P2_17 (ZCZ ball V12) */ + P2_17_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_17_default_pin>; + pinctrl-1 = <&P2_17_gpio_pin>; + pinctrl-2 = <&P2_17_gpio_pu_pin>; + pinctrl-3 = <&P2_17_gpio_pd_pin>; + pinctrl-4 = <&P2_17_gpio_input_pin>; + }; + + /* P2_18 (ZCZ ball U13) */ + P2_18_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pru_ecap", "pruin"; + pinctrl-0 = <&P2_18_default_pin>; + pinctrl-1 = <&P2_18_gpio_pin>; + pinctrl-2 = <&P2_18_gpio_pu_pin>; + pinctrl-3 = <&P2_18_gpio_pd_pin>; + pinctrl-4 = <&P2_18_gpio_input_pin>; + pinctrl-5 = <&P2_18_qep_pin>; + pinctrl-6 = <&P2_18_pru_ecap_pin>; + pinctrl-7 = <&P2_18_pruin_pin>; + }; + + /* P2_19 (ZCZ ball U12) */ + P2_19_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pwm"; + pinctrl-0 = <&P2_19_default_pin>; + pinctrl-1 = <&P2_19_gpio_pin>; + pinctrl-2 = <&P2_19_gpio_pu_pin>; + pinctrl-3 = <&P2_19_gpio_pd_pin>; + pinctrl-4 = <&P2_19_gpio_input_pin>; + pinctrl-5 = <&P2_19_pwm_pin>; + }; + + /* P2_20 (ZCZ ball T13) */ + P2_20_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input"; + pinctrl-0 = <&P2_20_default_pin>; + pinctrl-1 = <&P2_20_gpio_pin>; + pinctrl-2 = <&P2_20_gpio_pu_pin>; + pinctrl-3 = <&P2_20_gpio_pd_pin>; + pinctrl-4 = <&P2_20_gpio_input_pin>; + }; + + /* P2_21 GND */ + + /* P2_22 (ZCZ ball V13) */ + P2_22_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruin"; + pinctrl-0 = <&P2_22_default_pin>; + pinctrl-1 = <&P2_22_gpio_pin>; + pinctrl-2 = <&P2_22_gpio_pu_pin>; + pinctrl-3 = <&P2_22_gpio_pd_pin>; + pinctrl-4 = <&P2_22_gpio_input_pin>; + pinctrl-5 = <&P2_22_qep_pin>; + pinctrl-6 = <&P2_22_pruin_pin>; + }; + + /* P2_23 VOUT-3.3V */ + + /* P2_24 (ZCZ ball T12) */ + P2_24_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P2_24_default_pin>; + pinctrl-1 = <&P2_24_gpio_pin>; + pinctrl-2 = <&P2_24_gpio_pu_pin>; + pinctrl-3 = <&P2_24_gpio_pd_pin>; + pinctrl-4 = <&P2_24_gpio_input_pin>; + pinctrl-5 = <&P2_24_qep_pin>; + pinctrl-6 = <&P2_24_pruout_pin>; + }; + + /* P2_25 (ZCZ ball E17) spi */ + P2_25_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "spi_cs", "uart", "can", "i2c"; + pinctrl-0 = <&P2_25_default_pin>; + pinctrl-1 = <&P2_25_gpio_pin>; + pinctrl-2 = <&P2_25_gpio_pu_pin>; + pinctrl-3 = <&P2_25_gpio_pd_pin>; + pinctrl-4 = <&P2_25_gpio_input_pin>; + pinctrl-5 = <&P2_25_spi_pin>; + pinctrl-6 = <&P2_25_spi_cs_pin>; + pinctrl-7 = <&P2_25_uart_pin>; + pinctrl-8 = <&P2_25_can_pin>; + pinctrl-9 = <&P2_25_i2c_pin>; + }; + + /* P2_26 RESET# */ + + /* P2_27 (ZCZ ball E18) spi */ + P2_27_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "uart", "can", "i2c"; + pinctrl-0 = <&P2_27_default_pin>; + pinctrl-1 = <&P2_27_gpio_pin>; + pinctrl-2 = <&P2_27_gpio_pu_pin>; + pinctrl-3 = <&P2_27_gpio_pd_pin>; + pinctrl-4 = <&P2_27_gpio_input_pin>; + pinctrl-5 = <&P2_27_spi_pin>; + pinctrl-6 = <&P2_27_uart_pin>; + pinctrl-7 = <&P2_27_can_pin>; + pinctrl-8 = <&P2_27_i2c_pin>; + }; + + /* P2_28 (ZCZ ball D13) pruin */ + P2_28_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P2_28_default_pin>; + pinctrl-1 = <&P2_28_gpio_pin>; + pinctrl-2 = <&P2_28_gpio_pu_pin>; + pinctrl-3 = <&P2_28_gpio_pd_pin>; + pinctrl-4 = <&P2_28_gpio_input_pin>; + pinctrl-5 = <&P2_28_qep_pin>; + pinctrl-6 = <&P2_28_pruout_pin>; + pinctrl-7 = <&P2_28_pruin_pin>; + }; + + /* P2_29 (ZCZ ball C18) spi_sclk */ + P2_29_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "spi_sclk", "uart", "pwm", "pru_ecap"; + pinctrl-0 = <&P2_29_default_pin>; + pinctrl-1 = <&P2_29_gpio_pin>; + pinctrl-2 = <&P2_29_gpio_pu_pin>; + pinctrl-3 = <&P2_29_gpio_pd_pin>; + pinctrl-4 = <&P2_29_gpio_input_pin>; + pinctrl-5 = <&P2_29_spi_cs_pin>; + pinctrl-6 = <&P2_29_spi_sclk_pin>; + pinctrl-7 = <&P2_29_uart_pin>; + pinctrl-8 = <&P2_29_pwm_pin>; + pinctrl-9 = <&P2_29_pru_ecap_pin>; + }; + + /* P2_30 (ZCZ ball C12) pruin */ + P2_30_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P2_30_default_pin>; + pinctrl-1 = <&P2_30_gpio_pin>; + pinctrl-2 = <&P2_30_gpio_pu_pin>; + pinctrl-3 = <&P2_30_gpio_pd_pin>; + pinctrl-4 = <&P2_30_gpio_input_pin>; + pinctrl-5 = <&P2_30_spi_cs_pin>; + pinctrl-6 = <&P2_30_pwm_pin>; + pinctrl-7 = <&P2_30_pruout_pin>; + pinctrl-8 = <&P2_30_pruin_pin>; + }; + + /* P2_31 (ZCZ ball A15) spi_cs */ + P2_31_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi_cs", "pruin"; + pinctrl-0 = <&P2_31_default_pin>; + pinctrl-1 = <&P2_31_gpio_pin>; + pinctrl-2 = <&P2_31_gpio_pu_pin>; + pinctrl-3 = <&P2_31_gpio_pd_pin>; + pinctrl-4 = <&P2_31_gpio_input_pin>; + pinctrl-5 = <&P2_31_spi_cs_pin>; + pinctrl-6 = <&P2_31_pruin_pin>; + }; + + /* P2_32 (ZCZ ball D12) pruin */ + P2_32_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "spi", "pwm", "pruout", "pruin"; + pinctrl-0 = <&P2_32_default_pin>; + pinctrl-1 = <&P2_32_gpio_pin>; + pinctrl-2 = <&P2_32_gpio_pu_pin>; + pinctrl-3 = <&P2_32_gpio_pd_pin>; + pinctrl-4 = <&P2_32_gpio_input_pin>; + pinctrl-5 = <&P2_32_spi_pin>; + pinctrl-6 = <&P2_32_pwm_pin>; + pinctrl-7 = <&P2_32_pruout_pin>; + pinctrl-8 = <&P2_32_pruin_pin>; + }; + + /* P2_33 (ZCZ ball R12) */ + P2_33_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout"; + pinctrl-0 = <&P2_33_default_pin>; + pinctrl-1 = <&P2_33_gpio_pin>; + pinctrl-2 = <&P2_33_gpio_pu_pin>; + pinctrl-3 = <&P2_33_gpio_pd_pin>; + pinctrl-4 = <&P2_33_gpio_input_pin>; + pinctrl-5 = <&P2_33_qep_pin>; + pinctrl-6 = <&P2_33_pruout_pin>; + }; + + /* P2_34 (ZCZ ball C13) pruin */ + P2_34_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "qep", "pruout", "pruin"; + pinctrl-0 = <&P2_34_default_pin>; + pinctrl-1 = <&P2_34_gpio_pin>; + pinctrl-2 = <&P2_34_gpio_pu_pin>; + pinctrl-3 = <&P2_34_gpio_pd_pin>; + pinctrl-4 = <&P2_34_gpio_input_pin>; + pinctrl-5 = <&P2_34_qep_pin>; + pinctrl-6 = <&P2_34_pruout_pin>; + pinctrl-7 = <&P2_34_pruin_pin>; + }; + + /* P2_35 (ZCZ ball U5) gpio_input */ + P2_35_pinmux { + compatible = "bone-pinmux-helper"; + status = "okay"; + pinctrl-names = "default", "gpio", "gpio_pu", "gpio_pd", "gpio_input", "pruout", "pruin"; + pinctrl-0 = <&P2_35_default_pin>; + pinctrl-1 = <&P2_35_gpio_pin>; + pinctrl-2 = <&P2_35_gpio_pu_pin>; + pinctrl-3 = <&P2_35_gpio_pd_pin>; + pinctrl-4 = <&P2_35_gpio_input_pin>; + pinctrl-5 = <&P2_35_pruout_pin>; + pinctrl-6 = <&P2_35_pruin_pin>; + }; + + /* P2_36 (ZCZ ball C9) AIN7 */ + + cape-universal { + compatible = "gpio-of-helper"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + P1_02 { + gpio-name = "P1_02"; + gpio = <&gpio2 23 0>; + input; + dir-changeable; + }; + + P1_04 { + gpio-name = "P1_04"; + gpio = <&gpio2 25 0>; + input; + dir-changeable; + }; + + P1_06 { + gpio-name = "P1_06"; + gpio = <&gpio0 5 0>; + input; + dir-changeable; + }; + + P1_08 { + gpio-name = "P1_08"; + gpio = <&gpio0 2 0>; + input; + dir-changeable; + }; + + P1_10 { + gpio-name = "P1_10"; + gpio = <&gpio0 3 0>; + input; + dir-changeable; + }; + + P1_12 { + gpio-name = "P1_12"; + gpio = <&gpio0 4 0>; + input; + dir-changeable; + }; + + P1_20 { + gpio-name = "P1_20"; + gpio = <&gpio0 20 0>; + input; + dir-changeable; + }; + + P1_26 { + gpio-name = "P1_26"; + gpio = <&gpio0 12 0>; + input; + dir-changeable; + }; + + P1_28 { + gpio-name = "P1_28"; + gpio = <&gpio0 13 0>; + input; + dir-changeable; + }; + + P1_29 { + gpio-name = "P1_29"; + gpio = <&gpio3 21 0>; + input; + dir-changeable; + }; + + P1_30 { + gpio-name = "P1_30"; + gpio = <&gpio1 11 0>; + input; + dir-changeable; + }; + + P1_31 { + gpio-name = "P1_31"; + gpio = <&gpio3 18 0>; + input; + dir-changeable; + }; + + P1_32 { + gpio-name = "P1_32"; + gpio = <&gpio1 10 0>; + input; + dir-changeable; + }; + + P1_33 { + gpio-name = "P1_33"; + gpio = <&gpio3 15 0>; + input; + dir-changeable; + }; + + P1_34 { + gpio-name = "P1_34"; + gpio = <&gpio0 26 0>; + input; + dir-changeable; + }; + + P1_35 { + gpio-name = "P1_35"; + gpio = <&gpio2 24 0>; + input; + dir-changeable; + }; + + P1_36 { + gpio-name = "P1_36"; + gpio = <&gpio3 14 0>; + input; + dir-changeable; + }; + + P2_01 { + gpio-name = "P2_01"; + gpio = <&gpio1 18 0>; + input; + dir-changeable; + }; + + P2_02 { + gpio-name = "P2_02"; + gpio = <&gpio1 27 0>; + input; + dir-changeable; + }; + + P2_03 { + gpio-name = "P2_03"; + gpio = <&gpio0 23 0>; + input; + dir-changeable; + }; + + P2_04 { + gpio-name = "P2_04"; + gpio = <&gpio1 26 0>; + input; + dir-changeable; + }; + + P2_05 { + gpio-name = "P2_05"; + gpio = <&gpio0 30 0>; + input; + dir-changeable; + }; + + P2_06 { + gpio-name = "P2_06"; + gpio = <&gpio1 25 0>; + input; + dir-changeable; + }; + + P2_07 { + gpio-name = "P2_07"; + gpio = <&gpio0 31 0>; + input; + dir-changeable; + }; + + P2_08 { + gpio-name = "P2_08"; + gpio = <&gpio1 28 0>; + input; + dir-changeable; + }; + + P2_09 { + gpio-name = "P2_09"; + gpio = <&gpio0 15 0>; + input; + dir-changeable; + }; + + P2_10 { + gpio-name = "P2_10"; + gpio = <&gpio1 20 0>; + input; + dir-changeable; + }; + + P2_11 { + gpio-name = "P2_11"; + gpio = <&gpio0 14 0>; + input; + dir-changeable; + }; + + P2_17 { + gpio-name = "P2_17"; + gpio = <&gpio2 1 0>; + input; + dir-changeable; + }; + + P2_18 { + gpio-name = "P2_18"; + gpio = <&gpio1 15 0>; + input; + dir-changeable; + }; + + P2_19 { + gpio-name = "P2_19"; + gpio = <&gpio0 27 0>; + input; + dir-changeable; + }; + + P2_20 { + gpio-name = "P2_20"; + gpio = <&gpio2 0 0>; + input; + dir-changeable; + }; + + P2_22 { + gpio-name = "P2_22"; + gpio = <&gpio1 14 0>; + input; + dir-changeable; + }; + + P2_24 { + gpio-name = "P2_24"; + gpio = <&gpio1 12 0>; + input; + dir-changeable; + }; + + P2_25 { + gpio-name = "P2_25"; + gpio = <&gpio1 9 0>; + input; + dir-changeable; + }; + + P2_27 { + gpio-name = "P2_27"; + gpio = <&gpio1 8 0>; + input; + dir-changeable; + }; + + P2_28 { + gpio-name = "P2_28"; + gpio = <&gpio3 20 0>; + input; + dir-changeable; + }; + + P2_29 { + gpio-name = "P2_29"; + gpio = <&gpio0 7 0>; + input; + dir-changeable; + }; + + P2_30 { + gpio-name = "P2_30"; + gpio = <&gpio3 17 0>; + input; + dir-changeable; + }; + + P2_31 { + gpio-name = "P2_31"; + gpio = <&gpio0 19 0>; + input; + dir-changeable; + }; + + P2_32 { + gpio-name = "P2_32"; + gpio = <&gpio3 16 0>; + input; + dir-changeable; + }; + + P2_33 { + gpio-name = "P2_33"; + gpio = <&gpio1 13 0>; + input; + dir-changeable; + }; + + P2_34 { + gpio-name = "P2_34"; + gpio = <&gpio3 19 0>; + input; + dir-changeable; + }; + + P2_35 { + gpio-name = "P2_35"; + gpio = <&gpio2 22 0>; + input; + dir-changeable; + }; + + }; +}; diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe.dts b/arch/arm/boot/dts/am335x-sancloud-bbe.dts index e5fdb7a..820ff38 100644 --- a/arch/arm/boot/dts/am335x-sancloud-bbe.dts +++ b/arch/arm/boot/dts/am335x-sancloud-bbe.dts @@ -12,6 +12,11 @@ / { model = "SanCloud BeagleBone Enhanced"; compatible = "sancloud,am335x-boneenhanced", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx"; + + chosen { + base_dtb = "am335x-sancloud-bbe.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &am33xx_pinmux { diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi index 7a9eb2b..7c3cefb 100644 --- a/arch/arm/boot/dts/am33xx-l4.dtsi +++ b/arch/arm/boot/dts/am33xx-l4.dtsi @@ -158,6 +158,39 @@ #interrupt-cells = <2>; reg = <0x0 0x1000>; interrupts = <96>; + gpio-line-names = + "MDIO_DATA", // 0 + "MDIO_CLK", // 1 + "SPI0_SCLK", // 2 + "SPI0_D0", // 3 + "SPI0_D1", // 4 + "SPI0_CS0", // 5 + "SPI0_CS1", // 6 + "ECAP0_IN_PWM0_OUT", // 7 + "LCD_DATA12", // 8 + "LCD_DATA13", // 9 + "LCD_DATA14", // 10 + "LCD_DATA15", // 11 + "UART1_CTSN", // 12 + "UART1_RTSN", // 13 + "UART1_RXD", // 14 + "UART1_TXD", // 15 + "GMII1_TXD3", // 16 + "GMII1_TXD2", // 17 + "USB0_DRVVBUS", // 18 + "XDMA_EVENT_INTR0", // 19 + "XDMA_EVENT_INTR1", // 20 + "GMII1_TXD1", // 21 + "GPMC_AD8", // 22 + "GPMC_AD9", // 23 + "NC", // 24 + "NC", // 25 + "GPMC_AD10", // 26 + "GPMC_AD11", // 27 + "GMII1_TXD0", // 28 + "RMII1_REFCLK", // 29 + "GPMC_WAIT0", // 30 + "GPMC_WPN"; // 31 }; }; @@ -1299,6 +1332,39 @@ #interrupt-cells = <2>; reg = <0x0 0x1000>; interrupts = <98>; + gpio-line-names = + "GPMC_AD0", // 0 + "GPMC_AD1", // 1 + "GPMC_AD2", // 2 + "GPMC_AD3", // 3 + "GPMC_AD4", // 4 + "GPMC_AD5", // 5 + "GPMC_AD6", // 6 + "GPMC_AD7", // 7 + "UART0_CTSN", // 8 + "UART0_RTSN", // 9 + "UART0_RXD", // 10 + "UART0_TXD", // 11 + "GPMC_AD12", // 12 + "GPMC_AD13", // 13 + "GPMC_AD14", // 14 + "GPMC_AD15", // 15 + "GPMC_A0", // 16 + "GPMC_A1", // 17 + "GPMC_A2", // 18 + "GPMC_A3", // 19 + "GPMC_A4", // 20 + "GPMC_A5", // 21 + "GPMC_A6", // 22 + "GPMC_A7", // 23 + "GPMC_A8", // 24 + "GPMC_A9", // 25 + "GPMC_A10", // 26 + "GPMC_A11", // 27 + "GPMC_BE1N", // 28 + "GPMC_CSN0", // 29 + "GPMC_CSN1", // 30 + "GPMC_CSN2"; // 31 }; }; @@ -1711,6 +1777,39 @@ #interrupt-cells = <2>; reg = <0x0 0x1000>; interrupts = <32>; + gpio-line-names = + "GPMC_CSN3", // 0 + "GPMC_CLK", // 1 + "GPMC_ADVN_ALE", // 2 + "GPMC_OEN_REN", // 3 + "GPMC_WEN", // 4 + "GPMC_BE0N_CLE", // 5 + "LCD_DATA0", // 6 + "LCD_DATA1", // 7 + "LCD_DATA2", // 8 + "LCD_DATA3", // 9 + "LCD_DATA4", // 10 + "LCD_DATA5", // 11 + "LCD_DATA6", // 12 + "LCD_DATA7", // 13 + "LCD_DATA8", // 14 + "LCD_DATA9", // 15 + "LCD_DATA10", // 16 + "LCD_DATA11", // 17 + "GMII1_RXD3", // 18 + "GMII1_RXD2", // 19 + "GMII1_RXD1", // 20 + "GMII1_RXD0", // 21 + "LCD_VSYNC", // 22 + "LCD_HSYNC", // 23 + "LCD_PCLK", // 24 + "LCD_AC_BIAS_EN", // 25 + "MMC0_DAT3", // 26 + "MMC0_DAT2", // 27 + "MMC0_DAT1", // 28 + "MMC0_DAT0", // 29 + "MMC0_CLK", // 30 + "MMC0_CMD"; // 31 }; }; @@ -1745,6 +1844,39 @@ #interrupt-cells = <2>; reg = <0x0 0x1000>; interrupts = <62>; + gpio-line-names = + "GMII1_COL", // 0 + "GMII1_CRS", // 1 + "GMII1_RXER", // 2 + "GMII1_TXEN", // 3 + "GMII1_RXDV", // 4 + "I2C0_SDA", // 5 + "I2C0_SCL", // 6 + "EMU0", // 7 + "EMU1", // 8 + "GMII1_TXCLK", // 9 + "GMII1_RXCLK", // 10 + "NC", // 11 + "NC", // 12 + "USB1_DRVVBUS", // 13 + "MCASP0_ACLKX", // 14 + "MCASP0_FSX", // 15 + "MCASP0_AXR0", // 16 + "MCASP0_AHCLKR", // 17 + "MCASP0_ACLKR", // 18 + "MCASP0_FSR", // 19 + "MCASP0_AXR1", // 20 + "MCASP0_AHCLKX", // 21 + "NC", // 22 + "NC", // 23 + "NC", // 24 + "NC", // 25 + "NC", // 26 + "NC", // 27 + "NC", // 28 + "NC", // 29 + "NC", // 30 + "NC"; // 31 }; }; @@ -1914,6 +2046,15 @@ status = "disabled"; }; + eqep0: counter@180 { + compatible = "ti,am3352-eqep"; + reg = <0x180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "sysclkout"; + interrupts = <79>; + status = "disabled"; + }; + ehrpwm0: pwm@200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; @@ -1967,6 +2108,15 @@ status = "disabled"; }; + eqep1: counter@180 { + compatible = "ti,am3352-eqep"; + reg = <0x180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "sysclkout"; + interrupts = <88>; + status = "disabled"; + }; + ehrpwm1: pwm@200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; @@ -2020,6 +2170,15 @@ status = "disabled"; }; + eqep2: counter@180 { + compatible = "ti,am3352-eqep"; + reg = <0x180 0x80>; + clocks = <&l4ls_gclk>; + clock-names = "sysclkout"; + interrupts = <89>; + status = "disabled"; + }; + ehrpwm2: pwm@200 { compatible = "ti,am3352-ehrpwm", "ti,am33xx-ehrpwm"; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 37e297b..2ca4f0c 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -160,7 +160,7 @@ * for the moment, just use a fake OCP bus entry to represent * the whole bus hierarchy. */ - ocp { + ocp: ocp { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; diff --git b/arch/arm/boot/dts/am5729-beagleboneai.dts b/arch/arm/boot/dts/am5729-beagleboneai.dts new file mode 100644 index 0000000..6ad1a0b --- /dev/null +++ b/arch/arm/boot/dts/am5729-beagleboneai.dts @@ -0,0 +1,751 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2014-2019 Texas Instruments Incorporated - http://www.ti.com/ + */ + +/dts-v1/; + +#include "dra74x.dtsi" +#include "am57xx-commercial-grade.dtsi" +#include "dra74x-mmc-iodelay.dtsi" +#include +#include +#include + +/ { + model = "BeagleBoard.org BeagleBone AI"; + compatible = "beagle,am5729-beagleboneai", "ti,am5728", + "ti,dra742", "ti,dra74", "ti,dra7"; + + aliases { + rtc0 = &tps659038_rtc; + rtc1 = &rtc; + display0 = &hdmi_conn; + }; + + chosen { + stdout-path = &uart1; + base_dtb = "am5729-beagleboneai.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x40000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ipu2_memory_region: ipu2-memory@95800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x95800000 0x0 0x3800000>; + reusable; + status = "okay"; + }; + + dsp1_memory_region: dsp1-memory@99000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x99000000 0x0 0x4000000>; + reusable; + status = "okay"; + }; + + ipu1_memory_region: ipu1-memory@9d000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9d000000 0x0 0x2000000>; + reusable; + status = "okay"; + }; + + dsp2_memory_region: dsp2-memory@9f000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9f000000 0x0 0x800000>; + reusable; + status = "okay"; + }; + + }; + + vdd_adc: gpioregulator-vdd_adc { + compatible = "regulator-gpio"; + regulator-name = "vdd_adc"; + vin-supply = <&vdd_5v>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + states = <1800000 0 + 3300000 1>; + }; + + vdd_5v: fixedregulator-vdd_5v { + compatible = "regulator-fixed"; + regulator-name = "vdd_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vtt_fixed: fixedregulator-vtt { + /* TPS51200 */ + compatible = "regulator-fixed"; + regulator-name = "vtt_fixed"; + vin-supply = <&vdd_ddr>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + label = "beaglebone:green:usr0"; + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + label = "beaglebone:green:usr1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led2 { + label = "beaglebone:green:usr2"; + gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu"; + default-state = "off"; + }; + + led3 { + label = "beaglebone:green:usr3"; + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "beaglebone:green:usr4"; + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "netdev"; + default-state = "off"; + }; + }; + + hdmi_conn: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_encoder_out>; + }; + }; + }; + + hdmi_enc: encoder@0 { + /* "ti,tpd12s016" software compatible with "ti,tpd12s015" + * no need for individual driver + */ + compatible = "ti,tpd12s015"; + gpios = <0>, + <0>, + <&gpio7 12 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <0x1>; + #size-cells = <0x0>; + + port@0 { + reg = <0x0>; + + hdmi_encoder_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <0x1>; + + hdmi_encoder_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + emmc_pwrseq: emmc_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>; + }; + + brcmf_pwrseq: brcmf_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>, /* BT-REG-ON */ + <&gpio3 18 GPIO_ACTIVE_LOW>; /* WL-REG-ON */ + }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + ti,enable-id-detection; + id-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>; + }; +}; + +&dra7_pmx_core { + ethphy_extra_pins_default: ethphy_extra_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT_PULLUP | MUX_MODE14) /* N1: gpmc_advn_ale.gpio2_23 - RGMII_RST */ + DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT | MUX_MODE14) /* Y1: uart3_txd.gpio5_19 - MII0_INT */ + >; + }; + + pmic_pins_default: pmic_pins_default { + pinctrl-single,pins = < + DRA7XX_CORE_IOPAD(0x3690, PIN_INPUT_PULLUP | MUX_MODE14) /* F21: gpio6_16.gpio6_16 - PMIC_INT */ + >; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tps659038: tps659038@58 { + compatible = "ti,tps659038"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&pmic_pins_default>; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + ti,palmas-override-powerhold; + + tps659038_pmic { + compatible = "ti,tps659038-pmic"; + + smps12-in-supply = <&vdd_5v>; + smps3-in-supply = <&vdd_5v>; + smps45-in-supply = <&vdd_5v>; + smps6-in-supply = <&vdd_5v>; + smps7-in-supply = <&vdd_5v>; + mps3-in-supply = <&vdd_5v>; + smps8-in-supply = <&vdd_5v>; + smps9-in-supply = <&vdd_5v>; + ldo1-in-supply = <&vdd_5v>; + ldo2-in-supply = <&vdd_5v>; + ldo3-in-supply = <&vdd_5v>; + ldo4-in-supply = <&vdd_5v>; + ldo9-in-supply = <&vdd_5v>; + ldoln-in-supply = <&vdd_5v>; + ldousb-in-supply = <&vdd_5v>; + ldortc-in-supply = <&vdd_5v>; + + regulators { + vdd_mpu: smps12 { + /* VDD_MPU */ + regulator-name = "smps12"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_ddr: smps3 { + /* VDD_DDR EMIF1 EMIF2 */ + regulator-name = "smps3"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_dspeve: smps45 { + /* VDD_DSPEVE on AM572 */ + regulator-name = "smps45"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_gpu: smps6 { + /* VDD_GPU */ + regulator-name = "smps6"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_core: smps7 { + /* VDD_CORE */ + regulator-name = "smps7"; + regulator-min-microvolt = < 850000>; /*** 1.15V */ + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_iva: smps8 { + /* VDD_IVAHD */ /*** 1.06V */ + regulator-name = "smps8"; + }; + + vdd_3v3: smps9 { + /* VDD_3V3 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_sd: ldo1 { + /* VDDSHV8 - VSDMMC */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_1v8: ldo2 { + /* VDDSH18V */ + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo3: ldo3 { + /* R1.3a 572x V1_8PHY_LDO3: USB, SATA */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo4: ldo4 { + /* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + /* LDO5-8 unused */ + + vdd_rtc: ldo9 { + /* VDD_RTC */ + regulator-name = "ldo9"; + regulator-min-microvolt = < 840000>; + regulator-max-microvolt = <1160000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_pll: ldoln { + /* VDDA_1V8_PLL */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldortc_reg: ldortc { + /* VDDA_RTC */ + regulator-name = "ldortc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + regen1: regen1 { + /* VDD_3V3_ON */ + regulator-name = "regen1"; + regulator-boot-on; + regulator-always-on; + }; + + regen2: regen2 { + /* Needed for PMIC internal resource */ + regulator-name = "regen2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + + tps659038_rtc: tps659038_rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&tps659038>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + tps659038_pwr_button: tps659038_pwr_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + ti,palmas-long-press-seconds = <12>; + }; + + tps659038_gpio: tps659038_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + /* STMPE811 touch screen controller */ + stmpe811@41 { + compatible = "st,stmpe811"; + reg = <0x41>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio2>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + st,mod-12b = <1>; /* 12-bit ADC */ + st,ref-sel = <0>; /* internal ADC reference */ + st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */ + st,sample-time = <4>; /* ADC converstion time: 80 clocks */ + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x00>; /* mask any channels to be used by touchscreen */ + adc0: iio-device@0 { + #io-channel-cells = <1>; + iio-channels = <&adc0 4>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>, <&adc0 5>, <&adc0 6>; + iio-channel-names = "AIN0_P9_39", "AIN1_P9_40", "AIN2_P9_37", "AIN3_P9_38", + "AIN4_P9_33", "AIN5_P9_36", "AIN6_P9_35"; + }; + }; + + stmpe_touchscreen { + status = "disabled"; + compatible = "st,stmpe-ts"; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + }; + + stmpe_gpio { + compatible = "st,stmpe-gpio"; + }; + + stmpe_pwm { + compatible = "st,stmpe-pwm"; + #pwm-cells = <2>; + }; + }; +}; + +&mcspi3 { + status = "okay"; + ti,pindir-d0-out-d1-in; + + sn65hvs882: sn65hvs882@0 { + compatible = "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; +}; + +&cpu0 { + vdd-supply = <&vdd_mpu>; + voltage-tolerance = <1>; +}; + +&uart1 { + status = "okay"; +}; + +&davinci_mdio { + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + reset-delay-us = <2>; + + phy0: ethernet-phy@1 { + reg = <4>; + eee-broken-100tx; + eee-broken-1000t; + }; +}; + +&mac { + slaves = <1>; + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + phy-mode = "rgmii-rxid"; +}; + +&ocp { + pruss1_shmem: pruss_shmem@4b200000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b200000 0x020000>; + }; + + pruss2_shmem: pruss_shmem@4b280000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b280000 0x020000>; + }; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vdd_sd>; + bus-width = <4>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_default>; +}; + +&mmc2 { + status = "okay"; + vmmc-supply = <&vdd_1v8>; + vqmmc-supply = <&vdd_1v8>; + bus-width = <8>; + ti,non-removable; + non-removable; + mmc-pwrseq = <&emmc_pwrseq>; + + ti,needs-special-reset; + dmas = <&sdma_xbar 47>, <&sdma_xbar 48>; + dma-names = "tx", "rx"; + +}; + +&mmc4 { + /* DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). */ + /* HS: High speed up to 50 MHz (3.3 V signaling). */ + /* SDR12: SDR up to 25 MHz (1.8 V signaling). */ + /* SDR25: SDR up to 50 MHz (1.8 V signaling). */ + /* SDR50: SDR up to 100 MHz (1.8 V signaling). */ + /* SDR104: SDR up to 208 MHz (1.8 V signaling) */ + /* DDR50: DDR up to 50 MHz (1.8 V signaling). */ + status = "okay"; + + ti,needs-special-reset; + vmmc-supply = <&vdd_3v3>; + cap-power-off-card; + keep-power-in-suspend; + bus-width = <4>; + ti,non-removable; + non-removable; + no-1-8-v; + max-frequency = <24000000>; + + #address-cells = <1>; + #size-cells = <0>; + mmc-pwrseq = <&brcmf_pwrseq>; + + brcmf: wifi@1 { + status = "okay"; + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + + brcm,sd-head-align = <4>; + brcm,sd_head_align = <4>; + brcm,sd_sgentry_align = <512>; + + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +&usb2_phy1 { + phy-supply = <&ldousb_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldousb_reg>; +}; + +&usb1 { + status = "okay"; + dr_mode = "otg"; +}; + +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&usb2 { + status = "okay"; + dr_mode = "host"; +}; + +&dss { + status = "okay"; + vdda_video-supply = <&vdd_1v8_pll>; +}; + +&hdmi { + status = "okay"; + vdda-supply = <&vdd_1v8_phy_ldo4>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_encoder_in>; + }; + }; +}; + +&bandgap { + status = "okay"; +}; + +&mailbox1 { + status = "okay"; +}; + +&mailbox2 { + status = "okay"; +}; + +&mailbox3 { + status = "okay"; +}; + +&mailbox4 { + status = "okay"; +}; + +&mailbox5 { + status = "okay"; +}; + +&mailbox6 { + status = "okay"; +}; + +&mailbox7 { + status = "okay"; +}; + +&mailbox8 { + status = "okay"; +}; + +&mailbox9 { + status = "okay"; +}; + +&mailbox10 { + status = "okay"; +}; + +&mailbox11 { + status = "okay"; +}; + +&mailbox12 { + status = "okay"; +}; + +&mailbox13 { + status = "okay"; +}; + +&cpu_alert0 { + temperature = <55000>; /* milliCelsius */ +}; + +&cpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&gpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&core_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&dspeve_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&iva_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&sata { + status = "disabled"; +}; + +&sata_phy { + status = "disabled"; +}; + +/* bluetooth */ +&uart6 { + status = "okay"; +}; + +/* cape header stuff */ +&i2c4 { + status = "okay"; + clock-frequency = <100000>; +}; + +&cpu0_opp_table { + opp_slow-500000000 { + opp-shared; + }; +}; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index a813a0c..f3ad716 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -185,6 +185,10 @@ }; }; +&bb2d { + status = "okay"; +}; + &i2c1 { status = "okay"; clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts index 7b113b5..062ff48 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts @@ -7,6 +7,11 @@ / { model = "TI AM5728 BeagleBoard-X15 rev B1"; + + chosen { + base_dtb = "am57xx-beagle-x15-revb1.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts index 30c500b..4ad6551 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15-revc.dts @@ -7,6 +7,11 @@ / { model = "TI AM5728 BeagleBoard-X15 rev C"; + + chosen { + base_dtb = "am57xx-beagle-x15-revc.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index a5c24ed..dbda396 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -8,6 +8,11 @@ / { /* NOTE: This describes the "original" pre-production A2 revision */ model = "TI AM5728 BeagleBoard-X15"; + + chosen { + base_dtb = "am57xx-beagle-x15.dts"; + base_dtb_timestamp = __TIMESTAMP__; + }; }; &tpd12s015 { diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index a6ef3d1..dc7e890 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -143,7 +143,7 @@ * the moment, just use a fake OCP bus entry to represent the whole bus * hierarchy. */ - ocp { + ocp: ocp { compatible = "ti,dra7-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -380,6 +380,16 @@ ti,hwmods = "dmm"; }; + bb2d: bb2d@59000000 { + compatible = "ti,dra7-bb2d","vivante,gc"; + reg = <0x59000000 0x0700>; + interrupts = ; + ti,hwmods = "bb2d"; + clocks = <&dpll_core_h24x2_ck>; + clock-names = "fclk"; + status = "disabled"; + }; + mmu0_dsp1: mmu@40d01000 { compatible = "ti,dra7-dsp-iommu"; reg = <0x40d01000 0x100>; diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts index c63f371..546d9d4 100644 --- a/arch/arm/boot/dts/imx6q-evi.dts +++ b/arch/arm/boot/dts/imx6q-evi.dts @@ -55,18 +55,6 @@ reg = <0x10000000 0x40000000>; }; - reg_usbh1_vbus: regulator-usbhubreset { - compatible = "regulator-fixed"; - regulator-name = "usbh1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbh1_hubreset>; - gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>; - }; - reg_usb_otg_vbus: regulator-usbotgvbus { compatible = "regulator-fixed"; regulator-name = "usb_otg_vbus"; @@ -214,12 +202,18 @@ }; &usbh1 { - vbus-supply = <®_usbh1_vbus>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh1>; dr_mode = "host"; disable-over-current; status = "okay"; + + usb2415host: hub@1 { + compatible = "usb424,2513"; + reg = <1>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usbotg { @@ -482,11 +476,6 @@ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0 /* usbh1_b OC */ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 - >; - }; - - pinctrl_usbh1_hubreset: usbh1hubresetgrp { - fsl,pins = < MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 >; }; diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi index 776bfc7..554f601 100644 --- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi +++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi @@ -5,6 +5,8 @@ * Author: Fabio Estevam */ +#include + / { aliases { backlight = &backlight; @@ -62,17 +64,6 @@ #address-cells = <1>; #size-cells = <0>; - reg_usb_h1_vbus: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "usb_h1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */ - gpio = <&gpio7 12 0>; - }; - reg_panel: regulator@1 { compatible = "regulator-fixed"; reg = <1>; @@ -93,6 +84,17 @@ mux-int-port = <1>; mux-ext-port = <6>; }; + + udoo_ard: udoo_ard_manager { + compatible = "udoo,imx6q-udoo-ard"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_udooard>; + bossac-clk-gpio = <&gpio6 3 0>; + bossac-dat-gpio = <&gpio5 18 0>; + bossac-erase-gpio = <&gpio4 21 0>; + bossac-reset-gpio = <&gpio1 0 0>; + status = "okay"; + }; }; &fec { @@ -205,11 +207,20 @@ pinctrl_usbh: usbhgrp { fsl,pins = < - MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0 >; }; + pinctrl_udooard: udooardgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x80000000 + MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x80000000 + MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x80000000 + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x80000000 + >; + }; + pinctrl_usdhc3: usdhc3grp { fsl,pins = < MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 @@ -282,9 +293,16 @@ &usbh1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usbh>; - vbus-supply = <®_usb_h1_vbus>; - clocks = <&clks IMX6QDL_CLK_CKO>; status = "okay"; + + usb2415: hub@1 { + compatible = "usb424,2514"; + reg = <1>; + + clocks = <&clks IMX6QDL_CLK_CKO>; + reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; + reset-duration-us = <3000>; + }; }; &usdhc3 { diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi index e781a45..68daf55 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi @@ -6,6 +6,24 @@ #include "imx6qdl-wandboard.dtsi" +/ { + rfkill { + compatible = "wand,imx6qdl-wandboard-rfkill"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + bluetooth-on = <&gpio3 13 0>; + bluetooth-wake = <&gpio3 14 0>; + bluetooth-host-wake = <&gpio3 15 0>; + + wifi-ref-on = <&gpio2 29 0>; + wifi-rst-n = <&gpio5 2 0>; + wifi-reg-on = <&gpio1 26 0>; + wifi-host-wake = <&gpio1 29 0>; + wifi-wake = <&gpio1 30 0>; + }; +}; + &iomuxc { pinctrl-0 = <&pinctrl_hog>; @@ -31,6 +49,5 @@ &usdhc2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2>; - non-removable; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi index 3874e74..be5445d 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi @@ -6,6 +6,24 @@ #include "imx6qdl-wandboard.dtsi" +/ { + rfkill { + compatible = "wand,imx6qdl-wandboard-rfkill"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + bluetooth-on = <&gpio5 21 0>; + bluetooth-wake = <&gpio5 30 0>; + bluetooth-host-wake = <&gpio5 20 0>; + + wifi-ref-on = <&gpio5 31 0>; /* Wifi Power Enable */ + wifi-rst-n = <&gpio6 0 0>; /* WIFI_ON reset */ + wifi-reg-on = <&gpio1 26 0>; /* WL_REG_ON */ + wifi-host-wake = <&gpio1 29 0>; /* WL_HOST_WAKE */ + wifi-wake = <&gpio1 30 0>; /* WL_WAKE */ + }; +}; + &iomuxc { pinctrl-0 = <&pinctrl_hog>; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi index 9390979..d595f4e 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi @@ -7,6 +7,26 @@ #include "imx6qdl-wandboard.dtsi" / { + rfkill { + compatible = "wand,imx6qdl-wandboard-rfkill"; + pinctrl-names = "default"; + pinctrl-0 = <>; + + bluetooth-on = <&gpio5 30 0>; /* BT_RST_N */ + bluetooth-wake = <&gpio5 21 0>; /* BT_WAKE */ + bluetooth-host-wake = <&gpio5 20 0>; /* BT_HOST_WAKE */ + + wifi-ref-on = <&gpio6 0 0>; /* WIFI_ON: M4: CSI0_DAT14 */ + wifi-reg-on = <&gpio1 26 0>; /* WL_REG_ON: W22: ENET_RXD1 */ + wifi-host-wake = <&gpio1 29 0>; /* WL_HOST_WAKE: W20: ENET_TXD1 */ + + //HACK: use un-populated pins for missing rfkill pins, dont want to fix the driver... + //GPIO6_IO17 - SD3_DAT7 + //GPIO6_IO18 - SD3_DAT6 + wifi-rst-n = <&gpio6 17 0>; /* NOT POPULATED */ + wifi-wake = <&gpio6 18 0>; /* NOT POPULATED */ + }; + reg_eth_phy: regulator-eth-phy { compatible = "regulator-fixed"; regulator-name = "ETH_PHY"; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index b5fa2ce..91a9524 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -986,6 +986,8 @@ usbh1: usb@2184200 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184200 0x200>; interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -1000,6 +1002,8 @@ usbh2: usb@2184400 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184400 0x200>; interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; @@ -1015,6 +1019,8 @@ usbh3: usb@2184600 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + #address-cells = <1>; + #size-cells = <0>; reg = <0x02184600 0x200>; interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; diff --git a/arch/arm/boot/dts/imx7d-pico-pi.dts b/arch/arm/boot/dts/imx7d-pico-pi.dts index 70bea95..a50edba 100644 --- a/arch/arm/boot/dts/imx7d-pico-pi.dts +++ b/arch/arm/boot/dts/imx7d-pico-pi.dts @@ -8,6 +8,10 @@ model = "TechNexion PICO-IMX7D Board and PI baseboard"; compatible = "technexion,imx7d-pico-pi", "fsl,imx7d"; + chosen { + stdout-path = "serial4:115200n8"; + }; + leds { compatible = "gpio-leds"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 1aa99fc..28d5c07 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -152,6 +152,7 @@ }; etb@5401b000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -167,6 +168,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; @@ -214,6 +216,25 @@ >; }; + spi3_pins: pinmux_spi3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE1) /* sdmmc2_clk.mcspi3_clk gpio_130 */ + OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_cmd.mcspi3_simo gpio_131 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat0.mcspi3_somi gpio_132 */ + OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat2.mcspi3_cs1 gpio_134 */ + OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat3.mcspi3_cs0 gpio_135 */ + >; + }; + + spi4_pins: pinmux_spi4_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT | MUX_MODE1) /* mcbsp1_clkr.mcspi4_clk gpio_156 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_OUTPUT | MUX_MODE1) /* mcbsp1_dx.mcspi4_simo gpio_158 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE1) /* mcbsp1_dr.mcspi4_somi gpio_159 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* mcbsp1_fsx.mcspi4_cs0 gpio_161 */ + >; + }; + hsusb2_pins: pinmux_hsusb2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ @@ -291,7 +312,7 @@ }; twl_power: power { - compatible = "ti,twl4030-power-beagleboard-xm", "ti,twl4030-power-idle-osc-off"; + compatible = "ti,twl4030-power-reset"; ti,use_poweroff; }; }; @@ -322,6 +343,36 @@ status = "disabled"; }; +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&spi3_pins>; + status = "okay"; + + spidev0: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <48000000>; + }; + + spidev1: spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <48000000>; + }; +}; + +&mcspi4 { + pinctrl-names = "default"; + pinctrl-0 = <&spi4_pins>; + status = "okay"; + + spidev2: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <48000000>; + }; +}; + &twl_gpio { ti,use-leds; /* pullups: BIT(1) */ diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index e3df3c1..64f0787 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -139,6 +139,7 @@ }; etb@540000000 { + status = "disabled"; compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; @@ -154,6 +155,7 @@ }; etm@54010000 { + status = "disabled"; compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x54010000 0x1000>; @@ -272,9 +274,18 @@ codec { }; }; + + twl_power: power { + compatible = "ti,twl4030-power-reset"; + ti,use_poweroff; + }; }; }; +&i2c2 { + clock-frequency = <400000>; +}; + #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index 6408307..065f3db 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -7,6 +7,18 @@ #include "omap443x.dtsi" #include "omap4-panda-common.dtsi" +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 55ea8b6..fe11be5 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -481,16 +481,6 @@ }; }; -&emif1 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - -&emif2 { - cs1-used; - device-handle = <&elpida_ECB240ABACN>; -}; - &mcbsp1 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp1_pins>; diff --git b/arch/arm/boot/dts/omap4-panda-es-b3.dts b/arch/arm/boot/dts/omap4-panda-es-b3.dts new file mode 100644 index 0000000..19d02df --- /dev/null +++ b/arch/arm/boot/dts/omap4-panda-es-b3.dts @@ -0,0 +1,85 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap4460.dtsi" +#include "omap4-panda-common.dtsi" + +/ { + model = "TI OMAP4 PandaBoard-ES"; + compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; +}; + +/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ +&sound { + ti,model = "PandaBoardES"; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "AFML", "Line In", + "AFMR", "Line In"; +}; + +/* PandaboardES has external pullups on SCL & SDA */ +&dss_hdmi_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ + >; +}; + +&omap4_pmx_core { + led_gpio_pins: gpio_led_pmx { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0f6, PIN_OUTPUT | MUX_MODE3) /* gpio_110 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x11b, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */ + >; + }; +}; + +&led_wkgpio_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ + >; +}; + +&leds { + pinctrl-0 = < + &led_gpio_pins + &led_wkgpio_pins + >; + + heartbeat { + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; + }; + mmc { + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&gpio_keys { + buttonS2 { + gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* gpio_113 */ + }; +}; + +&gpio1_target { + ti,no-reset-on-init; +}; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index 9dd307b..ea4dce2 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -12,6 +12,18 @@ compatible = "ti,omap4-panda-es", "ti,omap4-panda", "ti,omap4460", "ti,omap4430", "ti,omap4"; }; +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + /* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ &sound { ti,model = "PandaBoardES"; diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index fb2f477..2ca852e 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -11,3 +11,15 @@ model = "TI OMAP4 PandaBoard"; compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4"; }; + +&emif1 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; + +&emif2 { + cs1-used; + device-handle = <&elpida_ECB240ABACN>; + status = "ok"; +}; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 91480ac..ded6a24 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -521,11 +521,13 @@ &emif1 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "ok"; }; &emif2 { cs1-used; device-handle = <&elpida_ECB240ABACN>; + status = "ok"; }; &keypad { diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index e5506ab..671502b 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -252,6 +252,7 @@ hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; + status = "disabled"; }; emif2: emif@4d000000 { @@ -264,6 +265,7 @@ hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; + status = "disabled"; }; aes1: aes@4b501000 { diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/twl6030.dtsi index 9d588cf..c0094e0 100644 --- a/arch/arm/boot/dts/twl6030.dtsi +++ b/arch/arm/boot/dts/twl6030.dtsi @@ -80,6 +80,11 @@ regulator-always-on; }; + clk32kg: regulator-clk32kg { + compatible = "ti,twl6030-clk32kg"; + regulator-always-on; + }; + twl_usb_comparator: usb-comparator { compatible = "ti,twl6030-usb"; interrupts = <4>, <10>; diff --git a/arch/arm/kernel/return_address.c b/arch/arm/kernel/return_address.c index b0d2f1f..fb0fc19 100644 --- a/arch/arm/kernel/return_address.c +++ b/arch/arm/kernel/return_address.c @@ -53,6 +53,7 @@ void *return_address(unsigned int level) return NULL; } +EXPORT_SYMBOL_GPL(return_address); + #endif /* if defined(CONFIG_FRAME_POINTER) && !defined(CONFIG_ARM_UNWIND) */ -EXPORT_SYMBOL_GPL(return_address); diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig index fdca73d..95e0e8e 100644 --- a/arch/arm/mach-imx/devices/Kconfig +++ b/arch/arm/mach-imx/devices/Kconfig @@ -69,3 +69,9 @@ config IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX config IMX_HAVE_PLATFORM_SPI_IMX bool + +config WAND_RFKILL + tristate "Wandboard RF Kill support" + depends on SOC_IMX6Q + default m + select RFKILL diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile index e44758a..c179a55 100644 --- a/arch/arm/mach-imx/devices/Makefile +++ b/arch/arm/mach-imx/devices/Makefile @@ -26,3 +26,4 @@ obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) += platform-spi_imx.o obj-$(CONFIG_IMX_HAVE_PLATFORM_MX2_EMMA) += platform-mx2-emma.o +obj-$(CONFIG_WAND_RFKILL) += wand-rfkill.o diff --git b/arch/arm/mach-imx/devices/wand-rfkill.c b/arch/arm/mach-imx/devices/wand-rfkill.c new file mode 100644 index 0000000..da7ef9f --- /dev/null +++ b/arch/arm/mach-imx/devices/wand-rfkill.c @@ -0,0 +1,290 @@ +/* + * arch/arm/mach-imx/devices/wand-rfkill.c + * + * Copyright (C) 2013 Vladimir Ermakov + * + * based on net/rfkill/rfkill-gpio.c + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + + +struct wand_rfkill_data { + struct rfkill *rfkill_dev; + int shutdown_gpio; + const char *shutdown_name; +}; + +static int wand_rfkill_set_block(void *data, bool blocked) +{ + struct wand_rfkill_data *rfkill = data; + + pr_debug("wandboard-rfkill: set block %d\n", blocked); + + if (blocked) { + if (gpio_is_valid(rfkill->shutdown_gpio)) + gpio_direction_output(rfkill->shutdown_gpio, 0); + } else { + if (gpio_is_valid(rfkill->shutdown_gpio)) + gpio_direction_output(rfkill->shutdown_gpio, 1); + } + + return 0; +} + +static const struct rfkill_ops wand_rfkill_ops = { + .set_block = wand_rfkill_set_block, +}; + +static int wand_rfkill_wifi_probe(struct device *dev, + struct device_node *np, + struct wand_rfkill_data *rfkill) +{ + int ret; + int wl_ref_on, wl_rst_n, wl_reg_on, wl_wake, wl_host_wake; + + wl_ref_on = of_get_named_gpio(np, "wifi-ref-on", 0); + wl_rst_n = of_get_named_gpio(np, "wifi-rst-n", 0); + wl_reg_on = of_get_named_gpio(np, "wifi-reg-on", 0); + wl_wake = of_get_named_gpio(np, "wifi-wake", 0); + wl_host_wake = of_get_named_gpio(np, "wifi-host-wake", 0); + + if (!gpio_is_valid(wl_rst_n) || !gpio_is_valid(wl_ref_on) || + !gpio_is_valid(wl_reg_on) || !gpio_is_valid(wl_wake) || + !gpio_is_valid(wl_host_wake)) { + + dev_err(dev, "incorrect wifi gpios (%d %d %d %d %d)\n", + wl_rst_n, wl_ref_on, wl_reg_on, wl_wake, wl_host_wake); + return -EINVAL; + } + + dev_info(dev, "initialize wifi chip\n"); + + gpio_request(wl_rst_n, "wl_rst_n"); + gpio_direction_output(wl_rst_n, 0); + msleep(11); + gpio_set_value(wl_rst_n, 1); + + gpio_request(wl_ref_on, "wl_ref_on"); + gpio_direction_output(wl_ref_on, 1); + + gpio_request(wl_reg_on, "wl_reg_on"); + gpio_direction_output(wl_reg_on, 1); + + gpio_request(wl_wake, "wl_wake"); + gpio_direction_output(wl_wake, 1); + + gpio_request(wl_host_wake, "wl_host_wake"); + gpio_direction_input(wl_host_wake); + + rfkill->shutdown_name = "wifi_shutdown"; + rfkill->shutdown_gpio = wl_wake; + + rfkill->rfkill_dev = rfkill_alloc("wifi-rfkill", dev, RFKILL_TYPE_WLAN, + &wand_rfkill_ops, rfkill); + if (!rfkill->rfkill_dev) { + ret = -ENOMEM; + goto wifi_fail_free_gpio; + } + + ret = rfkill_register(rfkill->rfkill_dev); + if (ret < 0) + goto wifi_fail_unregister; + + dev_info(dev, "wifi-rfkill registered.\n"); + + return 0; + +wifi_fail_unregister: + rfkill_destroy(rfkill->rfkill_dev); +wifi_fail_free_gpio: + if (gpio_is_valid(wl_rst_n)) gpio_free(wl_rst_n); + if (gpio_is_valid(wl_ref_on)) gpio_free(wl_ref_on); + if (gpio_is_valid(wl_reg_on)) gpio_free(wl_reg_on); + if (gpio_is_valid(wl_wake)) gpio_free(wl_wake); + if (gpio_is_valid(wl_host_wake)) gpio_free(wl_host_wake); + + return ret; +} + +static int wand_rfkill_bt_probe(struct device *dev, + struct device_node *np, + struct wand_rfkill_data *rfkill) +{ + int ret; + int bt_on, bt_wake, bt_host_wake; + + bt_on = of_get_named_gpio(np, "bluetooth-on", 0); + bt_wake = of_get_named_gpio(np, "bluetooth-wake", 0); + bt_host_wake = of_get_named_gpio(np, "bluetooth-host-wake", 0); + + if (!gpio_is_valid(bt_on) || !gpio_is_valid(bt_wake) || + !gpio_is_valid(bt_host_wake)) { + + dev_err(dev, "incorrect bt gpios (%d %d %d)\n", + bt_on, bt_wake, bt_host_wake); + return -EINVAL; + } + + dev_info(dev, "initialize bluetooth chip\n"); + + gpio_request(bt_on, "bt_on"); + gpio_direction_output(bt_on, 0); + msleep(11); + gpio_set_value(bt_on, 1); + + gpio_request(bt_wake, "bt_wake"); + gpio_direction_output(bt_wake, 1); + + gpio_request(bt_host_wake, "bt_host_wake"); + gpio_direction_input(bt_host_wake); + + rfkill->shutdown_name = "bluetooth_shutdown"; + rfkill->shutdown_gpio = bt_wake; + + rfkill->rfkill_dev = rfkill_alloc("bluetooth-rfkill", dev, RFKILL_TYPE_BLUETOOTH, + &wand_rfkill_ops, rfkill); + if (!rfkill->rfkill_dev) { + ret = -ENOMEM; + goto bt_fail_free_gpio; + } + + ret = rfkill_register(rfkill->rfkill_dev); + if (ret < 0) + goto bt_fail_unregister; + + dev_info(dev, "bluetooth-rfkill registered.\n"); + + return 0; + +bt_fail_unregister: + rfkill_destroy(rfkill->rfkill_dev); +bt_fail_free_gpio: + if (gpio_is_valid(bt_on)) gpio_free(bt_on); + if (gpio_is_valid(bt_wake)) gpio_free(bt_wake); + if (gpio_is_valid(bt_host_wake)) gpio_free(bt_host_wake); + + return ret; +} + +static int wand_rfkill_probe(struct platform_device *pdev) +{ + struct wand_rfkill_data *rfkill; + struct pinctrl *pinctrl; + int ret; + + dev_info(&pdev->dev, "Wandboard rfkill initialization\n"); + + if (!pdev->dev.of_node) { + dev_err(&pdev->dev, "no device tree node\n"); + return -ENODEV; + } + + rfkill = kzalloc(sizeof(*rfkill) * 2, GFP_KERNEL); + if (!rfkill) + return -ENOMEM; + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + int ret = PTR_ERR(pinctrl); + dev_err(&pdev->dev, "failed to get default pinctrl: %d\n", ret); + return ret; + } + + /* setup WiFi */ + ret = wand_rfkill_wifi_probe(&pdev->dev, pdev->dev.of_node, &rfkill[0]); + if (ret < 0) + goto fail_free_rfkill; + + /* setup bluetooth */ + ret = wand_rfkill_bt_probe(&pdev->dev, pdev->dev.of_node, &rfkill[1]); + if (ret < 0) + goto fail_unregister_wifi; + + platform_set_drvdata(pdev, rfkill); + + return 0; + +fail_unregister_wifi: + if (rfkill[1].rfkill_dev) { + rfkill_unregister(rfkill[1].rfkill_dev); + rfkill_destroy(rfkill[1].rfkill_dev); + } + + /* TODO free gpio */ + +fail_free_rfkill: + kfree(rfkill); + + return ret; +} + +static int wand_rfkill_remove(struct platform_device *pdev) +{ + struct wand_rfkill_data *rfkill = platform_get_drvdata(pdev); + + dev_info(&pdev->dev, "Module unloading\n"); + + if (!rfkill) + return 0; + + /* WiFi */ + if (gpio_is_valid(rfkill[0].shutdown_gpio)) + gpio_free(rfkill[0].shutdown_gpio); + + rfkill_unregister(rfkill[0].rfkill_dev); + rfkill_destroy(rfkill[0].rfkill_dev); + + /* Bt */ + if (gpio_is_valid(rfkill[1].shutdown_gpio)) + gpio_free(rfkill[1].shutdown_gpio); + + rfkill_unregister(rfkill[1].rfkill_dev); + rfkill_destroy(rfkill[1].rfkill_dev); + + kfree(rfkill); + + return 0; +} + +static struct of_device_id wand_rfkill_match[] = { + { .compatible = "wand,imx6q-wandboard-rfkill", }, + { .compatible = "wand,imx6dl-wandboard-rfkill", }, + { .compatible = "wand,imx6qdl-wandboard-rfkill", }, + {} +}; + +static struct platform_driver wand_rfkill_driver = { + .driver = { + .name = "wandboard-rfkill", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(wand_rfkill_match), + }, + .probe = wand_rfkill_probe, + .remove = wand_rfkill_remove +}; + +module_platform_driver(wand_rfkill_driver); + +MODULE_AUTHOR("Vladimir Ermakov "); +MODULE_DESCRIPTION("Wandboard rfkill driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/Makefile b/drivers/Makefile index aaef17c..b308fa2 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -55,6 +55,9 @@ obj-$(CONFIG_RESET_CONTROLLER) += reset/ obj-y += tty/ obj-y += char/ +# put mmc early as many morden devices use emm/sd card as rootfs storage +obj-y += mmc/ + # iommu/ comes before gpu as gpu are using iommu controllers obj-y += iommu/ @@ -127,7 +130,6 @@ obj-$(CONFIG_EISA) += eisa/ obj-$(CONFIG_PM_OPP) += opp/ obj-$(CONFIG_CPU_FREQ) += cpufreq/ obj-$(CONFIG_CPU_IDLE) += cpuidle/ -obj-y += mmc/ obj-$(CONFIG_MEMSTICK) += memstick/ obj-$(CONFIG_NEW_LEDS) += leds/ obj-$(CONFIG_INFINIBAND) += infiniband/ diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig index 47c2bb4..6095b6d 100644 --- a/drivers/bus/Kconfig +++ b/drivers/bus/Kconfig @@ -41,8 +41,9 @@ config MOXTET config HISILICON_LPC bool "Support for ISA I/O space on HiSilicon Hip06/7" - depends on ARM64 && (ARCH_HISI || COMPILE_TEST) - select INDIRECT_PIO + depends on (ARM64 && ARCH_HISI) || (COMPILE_TEST && !ALPHA && !HEXAGON && !PARISC && !C6X) + depends on HAS_IOMEM + select INDIRECT_PIO if ARM64 help Driver to enable I/O access to devices attached to the Low Pin Count bus on the HiSilicon Hip06/7 SoC. @@ -149,6 +150,15 @@ config TEGRA_GMI Driver for the Tegra Generic Memory Interface bus which can be used to attach devices such as NOR, UART, FPGA and more. +config TI_PWMSS + bool + default y if (ARCH_OMAP2PLUS) && (PWM_TIECAP || PWM_TIEHRPWM || TI_EQEP) + help + PWM Subsystem driver support for AM33xx SOC. + + PWM submodules require PWM config space access from submodule + drivers and require common parent driver support. + config TI_SYSC bool "TI sysc interconnect target module driver" depends on ARCH_OMAP2PLUS diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile index 16b43d3..1320bcf 100644 --- a/drivers/bus/Makefile +++ b/drivers/bus/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o obj-$(CONFIG_TEGRA_ACONNECT) += tegra-aconnect.o obj-$(CONFIG_TEGRA_GMI) += tegra-gmi.o +obj-$(CONFIG_TI_PWMSS) += ti-pwmss.o obj-$(CONFIG_TI_SYSC) += ti-sysc.o obj-$(CONFIG_TS_NBUS) += ts-nbus.o obj-$(CONFIG_UNIPHIER_SYSTEM_BUS) += uniphier-system-bus.o diff --git a/drivers/bus/fsl-mc/dprc-driver.c b/drivers/bus/fsl-mc/dprc-driver.c index 52c7e15..c8b1c38 100644 --- a/drivers/bus/fsl-mc/dprc-driver.c +++ b/drivers/bus/fsl-mc/dprc-driver.c @@ -104,10 +104,8 @@ static int __fsl_mc_device_match(struct device *dev, void *data) return fsl_mc_device_match(mc_dev, obj_desc); } -static struct fsl_mc_device *fsl_mc_device_lookup(struct fsl_mc_obj_desc - *obj_desc, - struct fsl_mc_device - *mc_bus_dev) +struct fsl_mc_device *fsl_mc_device_lookup(struct fsl_mc_obj_desc *obj_desc, + struct fsl_mc_device *mc_bus_dev) { struct device *dev; diff --git a/drivers/bus/fsl-mc/dprc.c b/drivers/bus/fsl-mc/dprc.c index 0fe3f52..602f030 100644 --- a/drivers/bus/fsl-mc/dprc.c +++ b/drivers/bus/fsl-mc/dprc.c @@ -554,3 +554,56 @@ int dprc_get_container_id(struct fsl_mc_io *mc_io, return 0; } + +/** + * dprc_get_connection() - Get connected endpoint and link status if connection + * exists. + * @mc_io: Pointer to MC portal's I/O object + * @cmd_flags: Command flags; one or more of 'MC_CMD_FLAG_' + * @token: Token of DPRC object + * @endpoint1: Endpoint 1 configuration parameters + * @endpoint2: Returned endpoint 2 configuration parameters + * @state: Returned link state: + * 1 - link is up; + * 0 - link is down; + * -1 - no connection (endpoint2 information is irrelevant) + * + * Return: '0' on Success; -ENOTCONN if connection does not exist. + */ +int dprc_get_connection(struct fsl_mc_io *mc_io, + u32 cmd_flags, + u16 token, + const struct dprc_endpoint *endpoint1, + struct dprc_endpoint *endpoint2, + int *state) +{ + struct dprc_cmd_get_connection *cmd_params; + struct dprc_rsp_get_connection *rsp_params; + struct fsl_mc_command cmd = { 0 }; + int err, i; + + /* prepare command */ + cmd.header = mc_encode_cmd_header(DPRC_CMDID_GET_CONNECTION, + cmd_flags, + token); + cmd_params = (struct dprc_cmd_get_connection *)cmd.params; + cmd_params->ep1_id = cpu_to_le32(endpoint1->id); + cmd_params->ep1_interface_id = cpu_to_le16(endpoint1->if_id); + for (i = 0; i < 16; i++) + cmd_params->ep1_type[i] = endpoint1->type[i]; + + /* send command to mc */ + err = mc_send_command(mc_io, &cmd); + if (err) + return -ENOTCONN; + + /* retrieve response parameters */ + rsp_params = (struct dprc_rsp_get_connection *)cmd.params; + endpoint2->id = le32_to_cpu(rsp_params->ep2_id); + endpoint2->if_id = le16_to_cpu(rsp_params->ep2_interface_id); + *state = le32_to_cpu(rsp_params->state); + for (i = 0; i < 16; i++) + endpoint2->type[i] = rsp_params->ep2_type[i]; + + return 0; +} diff --git a/drivers/bus/fsl-mc/fsl-mc-bus.c b/drivers/bus/fsl-mc/fsl-mc-bus.c index 5c9bf2e..c78d10e 100644 --- a/drivers/bus/fsl-mc/fsl-mc-bus.c +++ b/drivers/bus/fsl-mc/fsl-mc-bus.c @@ -166,42 +166,52 @@ EXPORT_SYMBOL_GPL(fsl_mc_bus_type); struct device_type fsl_mc_bus_dprc_type = { .name = "fsl_mc_bus_dprc" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dprc_type); struct device_type fsl_mc_bus_dpni_type = { .name = "fsl_mc_bus_dpni" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpni_type); struct device_type fsl_mc_bus_dpio_type = { .name = "fsl_mc_bus_dpio" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpio_type); struct device_type fsl_mc_bus_dpsw_type = { .name = "fsl_mc_bus_dpsw" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpsw_type); struct device_type fsl_mc_bus_dpbp_type = { .name = "fsl_mc_bus_dpbp" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpbp_type); struct device_type fsl_mc_bus_dpcon_type = { .name = "fsl_mc_bus_dpcon" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpcon_type); struct device_type fsl_mc_bus_dpmcp_type = { .name = "fsl_mc_bus_dpmcp" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpmcp_type); struct device_type fsl_mc_bus_dpmac_type = { .name = "fsl_mc_bus_dpmac" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpmac_type); struct device_type fsl_mc_bus_dprtc_type = { .name = "fsl_mc_bus_dprtc" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dprtc_type); struct device_type fsl_mc_bus_dpseci_type = { .name = "fsl_mc_bus_dpseci" }; +EXPORT_SYMBOL_GPL(fsl_mc_bus_dpseci_type); static struct device_type *fsl_mc_get_device_type(const char *type) { @@ -702,6 +712,39 @@ void fsl_mc_device_remove(struct fsl_mc_device *mc_dev) } EXPORT_SYMBOL_GPL(fsl_mc_device_remove); +struct fsl_mc_device *fsl_mc_get_endpoint(struct fsl_mc_device *mc_dev) +{ + struct fsl_mc_device *mc_bus_dev, *endpoint; + struct fsl_mc_obj_desc endpoint_desc = {{ 0 }}; + struct dprc_endpoint endpoint1 = {{ 0 }}; + struct dprc_endpoint endpoint2 = {{ 0 }}; + int state, err; + + mc_bus_dev = to_fsl_mc_device(mc_dev->dev.parent); + strcpy(endpoint1.type, mc_dev->obj_desc.type); + endpoint1.id = mc_dev->obj_desc.id; + + err = dprc_get_connection(mc_bus_dev->mc_io, 0, + mc_bus_dev->mc_handle, + &endpoint1, &endpoint2, + &state); + + if (err == -ENOTCONN || state == -1) + return ERR_PTR(-ENOTCONN); + + if (err < 0) { + dev_err(&mc_bus_dev->dev, "dprc_get_connection() = %d\n", err); + return ERR_PTR(err); + } + + strcpy(endpoint_desc.type, endpoint2.type); + endpoint_desc.id = endpoint2.id; + endpoint = fsl_mc_device_lookup(&endpoint_desc, mc_bus_dev); + + return endpoint; +} +EXPORT_SYMBOL_GPL(fsl_mc_get_endpoint); + static int parse_mc_ranges(struct device *dev, int *paddr_cells, int *mc_addr_cells, diff --git a/drivers/bus/fsl-mc/fsl-mc-private.h b/drivers/bus/fsl-mc/fsl-mc-private.h index 020fcc0..21ca8c7 100644 --- a/drivers/bus/fsl-mc/fsl-mc-private.h +++ b/drivers/bus/fsl-mc/fsl-mc-private.h @@ -105,6 +105,8 @@ int dpmcp_reset(struct fsl_mc_io *mc_io, #define DPRC_CMDID_GET_OBJ_REG_V2 DPRC_CMD_V2(0x15E) #define DPRC_CMDID_SET_OBJ_IRQ DPRC_CMD(0x15F) +#define DPRC_CMDID_GET_CONNECTION DPRC_CMD(0x16C) + struct dprc_cmd_open { __le32 container_id; }; @@ -228,6 +230,22 @@ struct dprc_cmd_set_obj_irq { u8 obj_type[16]; }; +struct dprc_cmd_get_connection { + __le32 ep1_id; + __le16 ep1_interface_id; + u8 pad[2]; + u8 ep1_type[16]; +}; + +struct dprc_rsp_get_connection { + __le64 pad[3]; + __le32 ep2_id; + __le16 ep2_interface_id; + __le16 pad1; + u8 ep2_type[16]; + __le32 state; +}; + /* * DPRC API for managing and querying DPAA resources */ @@ -392,6 +410,27 @@ int dprc_get_container_id(struct fsl_mc_io *mc_io, u32 cmd_flags, int *container_id); +/** + * struct dprc_endpoint - Endpoint description for link connect/disconnect + * operations + * @type: Endpoint object type: NULL terminated string + * @id: Endpoint object ID + * @if_id: Interface ID; should be set for endpoints with multiple + * interfaces ("dpsw", "dpdmux"); for others, always set to 0 + */ +struct dprc_endpoint { + char type[16]; + int id; + u16 if_id; +}; + +int dprc_get_connection(struct fsl_mc_io *mc_io, + u32 cmd_flags, + u16 token, + const struct dprc_endpoint *endpoint1, + struct dprc_endpoint *endpoint2, + int *state); + /* * Data Path Buffer Pool (DPBP) API */ @@ -574,4 +613,7 @@ void fsl_destroy_mc_io(struct fsl_mc_io *mc_io); bool fsl_mc_is_root_dprc(struct device *dev); +struct fsl_mc_device *fsl_mc_device_lookup(struct fsl_mc_obj_desc *obj_desc, + struct fsl_mc_device *mc_bus_dev); + #endif /* _FSL_MC_PRIVATE_H_ */ diff --git a/drivers/bus/hisi_lpc.c b/drivers/bus/hisi_lpc.c index 20c9571..8101df9 100644 --- a/drivers/bus/hisi_lpc.c +++ b/drivers/bus/hisi_lpc.c @@ -74,7 +74,7 @@ struct hisi_lpc_dev { /* About 10us. This is specific for single IO operations, such as inb */ #define LPC_PEROP_WAITCNT 100 -static int wait_lpc_idle(unsigned char *mbase, unsigned int waitcnt) +static int wait_lpc_idle(void __iomem *mbase, unsigned int waitcnt) { u32 status; @@ -209,7 +209,7 @@ static u32 hisi_lpc_comm_in(void *hostdata, unsigned long pio, size_t dwidth) struct hisi_lpc_dev *lpcdev = hostdata; struct lpc_cycle_para iopara; unsigned long addr; - u32 rd_data = 0; + __le32 rd_data = 0; int ret; if (!lpcdev || !dwidth || dwidth > LPC_MAX_DWIDTH) @@ -244,13 +244,12 @@ static void hisi_lpc_comm_out(void *hostdata, unsigned long pio, struct lpc_cycle_para iopara; const unsigned char *buf; unsigned long addr; + __le32 _val = cpu_to_le32(val); if (!lpcdev || !dwidth || dwidth > LPC_MAX_DWIDTH) return; - val = cpu_to_le32(val); - - buf = (const unsigned char *)&val; + buf = (const unsigned char *)&_val; addr = hisi_lpc_pio_to_addr(lpcdev, pio); iopara.opflags = FG_INCRADDR_LPC; diff --git b/drivers/bus/ti-pwmss.c b/drivers/bus/ti-pwmss.c new file mode 100644 index 0000000..e9c26c9 --- /dev/null +++ b/drivers/bus/ti-pwmss.c @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * TI PWM Subsystem driver + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + */ + +#include +#include +#include +#include +#include +#include + +static const struct of_device_id pwmss_of_match[] = { + { .compatible = "ti,am33xx-pwmss" }, + {}, +}; +MODULE_DEVICE_TABLE(of, pwmss_of_match); + +static int pwmss_probe(struct platform_device *pdev) +{ + int ret; + struct device_node *node = pdev->dev.of_node; + + pm_runtime_enable(&pdev->dev); + + /* Populate all the child nodes here... */ + ret = of_platform_populate(node, NULL, NULL, &pdev->dev); + if (ret) + dev_err(&pdev->dev, "no child node found\n"); + + return ret; +} + +static int pwmss_remove(struct platform_device *pdev) +{ + pm_runtime_disable(&pdev->dev); + return 0; +} + +static struct platform_driver pwmss_driver = { + .driver = { + .name = "pwmss", + .of_match_table = pwmss_of_match, + }, + .probe = pwmss_probe, + .remove = pwmss_remove, +}; + +module_platform_driver(pwmss_driver); + +MODULE_DESCRIPTION("PWM Subsystem driver"); +MODULE_AUTHOR("Texas Instruments"); +MODULE_LICENSE("GPL"); diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index 770a780..c42447d 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -70,13 +70,11 @@ static const char * const clock_names[SYSC_MAX_CLOCKS] = { * @child_needs_resume: runtime resume needed for child on resume from suspend * @disable_on_idle: status flag used for disabling modules with resets * @idle_work: work structure used to perform delayed idle on a module - * @pre_reset_quirk: module specific pre-reset quirk - * @post_reset_quirk: module specific post-reset quirk + * @clk_enable_quirk: module specific clock enable quirk + * @clk_disable_quirk: module specific clock disable quirk * @reset_done_quirk: module specific reset done quirk * @module_enable_quirk: module specific enable quirk * @module_disable_quirk: module specific disable quirk - * @module_unlock_quirk: module specific sysconfig unlock quirk - * @module_lock_quirk: module specific sysconfig lock quirk */ struct sysc { struct device *dev; @@ -99,13 +97,11 @@ struct sysc { unsigned int needs_resume:1; unsigned int child_needs_resume:1; struct delayed_work idle_work; - void (*pre_reset_quirk)(struct sysc *sysc); - void (*post_reset_quirk)(struct sysc *sysc); + void (*clk_enable_quirk)(struct sysc *sysc); + void (*clk_disable_quirk)(struct sysc *sysc); void (*reset_done_quirk)(struct sysc *sysc); void (*module_enable_quirk)(struct sysc *sysc); void (*module_disable_quirk)(struct sysc *sysc); - void (*module_unlock_quirk)(struct sysc *sysc); - void (*module_lock_quirk)(struct sysc *sysc); }; static void sysc_parse_dts_quirks(struct sysc *ddata, struct device_node *np, @@ -186,34 +182,6 @@ static u32 sysc_read_sysstatus(struct sysc *ddata) return sysc_read(ddata, offset); } -/* Poll on reset status */ -static int sysc_wait_softreset(struct sysc *ddata) -{ - u32 sysc_mask, syss_done, rstval; - int syss_offset, error = 0; - - syss_offset = ddata->offsets[SYSC_SYSSTATUS]; - sysc_mask = BIT(ddata->cap->regbits->srst_shift); - - if (ddata->cfg.quirks & SYSS_QUIRK_RESETDONE_INVERTED) - syss_done = 0; - else - syss_done = ddata->cfg.syss_mask; - - if (syss_offset >= 0) { - error = readx_poll_timeout_atomic(sysc_read_sysstatus, ddata, - rstval, (rstval & ddata->cfg.syss_mask) == - syss_done, 100, MAX_MODULE_SOFTRESET_WAIT); - - } else if (ddata->cfg.quirks & SYSC_QUIRK_RESET_STATUS) { - error = readx_poll_timeout_atomic(sysc_read_sysconfig, ddata, - rstval, !(rstval & sysc_mask), - 100, MAX_MODULE_SOFTRESET_WAIT); - } - - return error; -} - static int sysc_add_named_clock_from_child(struct sysc *ddata, const char *name, const char *optfck_name) @@ -895,22 +863,6 @@ static void sysc_show_registers(struct sysc *ddata) buf); } -/** - * sysc_write_sysconfig - handle sysconfig quirks for register write - * @ddata: device driver data - * @value: register value - */ -static void sysc_write_sysconfig(struct sysc *ddata, u32 value) -{ - if (ddata->module_unlock_quirk) - ddata->module_unlock_quirk(ddata); - - sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], value); - - if (ddata->module_lock_quirk) - ddata->module_lock_quirk(ddata); -} - #define SYSC_IDLE_MASK (SYSC_NR_IDLEMODES - 1) #define SYSC_CLOCACT_ICK 2 @@ -920,47 +872,18 @@ static int sysc_enable_module(struct device *dev) struct sysc *ddata; const struct sysc_regbits *regbits; u32 reg, idlemodes, best_mode; - int error; ddata = dev_get_drvdata(dev); - - /* - * Some modules like DSS reset automatically on idle. Enable optional - * reset clocks and wait for OCP softreset to complete. - */ - if (ddata->cfg.quirks & SYSC_QUIRK_OPT_CLKS_IN_RESET) { - error = sysc_enable_opt_clocks(ddata); - if (error) { - dev_err(ddata->dev, - "Optional clocks failed for enable: %i\n", - error); - return error; - } - } - error = sysc_wait_softreset(ddata); - if (error) - dev_warn(ddata->dev, "OCP softreset timed out\n"); - if (ddata->cfg.quirks & SYSC_QUIRK_OPT_CLKS_IN_RESET) - sysc_disable_opt_clocks(ddata); - - /* - * Some subsystem private interconnects, like DSS top level module, - * need only the automatic OCP softreset handling with no sysconfig - * register bits to configure. - */ if (ddata->offsets[SYSC_SYSCONFIG] == -ENODEV) return 0; regbits = ddata->cap->regbits; reg = sysc_read(ddata, ddata->offsets[SYSC_SYSCONFIG]); - /* - * Set CLOCKACTIVITY, we only use it for ick. And we only configure it - * based on the SYSC_QUIRK_USE_CLOCKACT flag, not based on the hardware - * capabilities. See the old HWMOD_SET_DEFAULT_CLOCKACT flag. - */ + /* Set CLOCKACTIVITY, we only use it for ick */ if (regbits->clkact_shift >= 0 && - (ddata->cfg.quirks & SYSC_QUIRK_USE_CLOCKACT)) + (ddata->cfg.quirks & SYSC_QUIRK_USE_CLOCKACT || + ddata->cfg.sysc_val & BIT(regbits->clkact_shift))) reg |= SYSC_CLOCACT_ICK << regbits->clkact_shift; /* Set SIDLE mode */ @@ -986,7 +909,7 @@ static int sysc_enable_module(struct device *dev) reg &= ~(SYSC_IDLE_MASK << regbits->sidle_shift); reg |= best_mode << regbits->sidle_shift; - sysc_write_sysconfig(ddata, reg); + sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], reg); set_midle: /* Set MIDLE mode */ @@ -1005,19 +928,16 @@ set_midle: reg &= ~(SYSC_IDLE_MASK << regbits->midle_shift); reg |= best_mode << regbits->midle_shift; - sysc_write_sysconfig(ddata, reg); + sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], reg); set_autoidle: /* Autoidle bit must enabled separately if available */ if (regbits->autoidle_shift >= 0 && ddata->cfg.sysc_val & BIT(regbits->autoidle_shift)) { reg |= 1 << regbits->autoidle_shift; - sysc_write_sysconfig(ddata, reg); + sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], reg); } - /* Flush posted write */ - sysc_read(ddata, ddata->offsets[SYSC_SYSCONFIG]); - if (ddata->module_enable_quirk) ddata->module_enable_quirk(ddata); @@ -1073,7 +993,7 @@ static int sysc_disable_module(struct device *dev) reg &= ~(SYSC_IDLE_MASK << regbits->midle_shift); reg |= best_mode << regbits->midle_shift; - sysc_write_sysconfig(ddata, reg); + sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], reg); set_sidle: /* Set SIDLE mode */ @@ -1096,10 +1016,7 @@ set_sidle: if (regbits->autoidle_shift >= 0 && ddata->cfg.sysc_val & BIT(regbits->autoidle_shift)) reg |= 1 << regbits->autoidle_shift; - sysc_write_sysconfig(ddata, reg); - - /* Flush posted write */ - sysc_read(ddata, ddata->offsets[SYSC_SYSCONFIG]); + sysc_write(ddata, ddata->offsets[SYSC_SYSCONFIG], reg); return 0; } @@ -1133,8 +1050,6 @@ static int __maybe_unused sysc_runtime_resume_legacy(struct device *dev, struct ti_sysc_platform_data *pdata; int error; - reset_control_deassert(ddata->rsts); - pdata = dev_get_platdata(ddata->dev); if (!pdata) return 0; @@ -1147,6 +1062,8 @@ static int __maybe_unused sysc_runtime_resume_legacy(struct device *dev, dev_err(dev, "%s: could not enable: %i\n", __func__, error); + reset_control_deassert(ddata->rsts); + return 0; } @@ -1200,8 +1117,6 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev) sysc_clkdm_deny_idle(ddata); - reset_control_deassert(ddata->rsts); - if (sysc_opt_clks_needed(ddata)) { error = sysc_enable_opt_clocks(ddata); if (error) @@ -1212,6 +1127,8 @@ static int __maybe_unused sysc_runtime_resume(struct device *dev) if (error) goto err_opt_clocks; + reset_control_deassert(ddata->rsts); + if (ddata->legacy_mode) { error = sysc_runtime_resume_legacy(dev, ddata); if (error) @@ -1245,8 +1162,7 @@ static int __maybe_unused sysc_noirq_suspend(struct device *dev) ddata = dev_get_drvdata(dev); - if (ddata->cfg.quirks & - (SYSC_QUIRK_LEGACY_IDLE | SYSC_QUIRK_NO_IDLE)) + if (ddata->cfg.quirks & SYSC_QUIRK_LEGACY_IDLE) return 0; return pm_runtime_force_suspend(dev); @@ -1258,8 +1174,7 @@ static int __maybe_unused sysc_noirq_resume(struct device *dev) ddata = dev_get_drvdata(dev); - if (ddata->cfg.quirks & - (SYSC_QUIRK_LEGACY_IDLE | SYSC_QUIRK_NO_IDLE)) + if (ddata->cfg.quirks & SYSC_QUIRK_LEGACY_IDLE) return 0; return pm_runtime_force_resume(dev); @@ -1307,16 +1222,16 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_QUIRK_LEGACY_IDLE), SYSC_QUIRK("sham", 0, 0x100, 0x110, 0x114, 0x40000c03, 0xffffffff, SYSC_QUIRK_LEGACY_IDLE), - SYSC_QUIRK("smartreflex", 0, -ENODEV, 0x24, -ENODEV, 0x00000000, 0xffffffff, + SYSC_QUIRK("smartreflex", 0, -1, 0x24, -1, 0x00000000, 0xffffffff, SYSC_QUIRK_LEGACY_IDLE), - SYSC_QUIRK("smartreflex", 0, -ENODEV, 0x38, -ENODEV, 0x00000000, 0xffffffff, + SYSC_QUIRK("smartreflex", 0, -1, 0x38, -1, 0x00000000, 0xffffffff, SYSC_QUIRK_LEGACY_IDLE), SYSC_QUIRK("timer", 0, 0, 0x10, 0x14, 0x00000015, 0xffffffff, 0), /* Some timers on omap4 and later */ - SYSC_QUIRK("timer", 0, 0, 0x10, -ENODEV, 0x50002100, 0xffffffff, + SYSC_QUIRK("timer", 0, 0, 0x10, -1, 0x50002100, 0xffffffff, 0), - SYSC_QUIRK("timer", 0, 0, 0x10, -ENODEV, 0x4fff1301, 0xffff00ff, + SYSC_QUIRK("timer", 0, 0, 0x10, -1, 0x4fff1301, 0xffff00ff, 0), SYSC_QUIRK("uart", 0, 0x50, 0x54, 0x58, 0x00000046, 0xffffffff, SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_LEGACY_IDLE), @@ -1329,27 +1244,19 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_QUIRK_SWSUP_SIDLE_ACT | SYSC_QUIRK_LEGACY_IDLE), /* Quirks that need to be set based on the module address */ - SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -ENODEV, 0x50000800, 0xffffffff, + SYSC_QUIRK("mcpdm", 0x40132000, 0, 0x10, -1, 0x50000800, 0xffffffff, SYSC_QUIRK_EXT_OPT_CLOCK | SYSC_QUIRK_NO_RESET_ON_INIT | SYSC_QUIRK_SWSUP_SIDLE), /* Quirks that need to be set based on detected module */ - SYSC_QUIRK("aess", 0, 0, 0x10, -ENODEV, 0x40000000, 0xffffffff, + SYSC_QUIRK("aess", 0, 0, 0x10, -1, 0x40000000, 0xffffffff, SYSC_MODULE_QUIRK_AESS), - SYSC_QUIRK("dcan", 0x48480000, 0x20, -ENODEV, -ENODEV, 0xa3170504, 0xffffffff, + SYSC_QUIRK("dcan", 0x48480000, 0x20, -1, -1, 0xa3170504, 0xffffffff, SYSC_QUIRK_CLKDM_NOAUTO), - SYSC_QUIRK("dss", 0x4832a000, 0, 0x10, 0x14, 0x00000020, 0xffffffff, - SYSC_QUIRK_OPT_CLKS_IN_RESET), - SYSC_QUIRK("dss", 0x58000000, 0, -ENODEV, 0x14, 0x00000040, 0xffffffff, - SYSC_QUIRK_OPT_CLKS_IN_RESET), - SYSC_QUIRK("dss", 0x58000000, 0, -ENODEV, 0x14, 0x00000061, 0xffffffff, - SYSC_QUIRK_OPT_CLKS_IN_RESET), - SYSC_QUIRK("dwc3", 0x48880000, 0, 0x10, -ENODEV, 0x500a0200, 0xffffffff, + SYSC_QUIRK("dwc3", 0x48880000, 0, 0x10, -1, 0x500a0200, 0xffffffff, SYSC_QUIRK_CLKDM_NOAUTO), - SYSC_QUIRK("dwc3", 0x488c0000, 0, 0x10, -ENODEV, 0x500a0200, 0xffffffff, + SYSC_QUIRK("dwc3", 0x488c0000, 0, 0x10, -1, 0x500a0200, 0xffffffff, SYSC_QUIRK_CLKDM_NOAUTO), - SYSC_QUIRK("hdmi", 0, 0, 0x10, -ENODEV, 0x50030200, 0xffffffff, - SYSC_QUIRK_OPT_CLKS_NEEDED), SYSC_QUIRK("hdq1w", 0, 0, 0x14, 0x18, 0x00000006, 0xffffffff, SYSC_MODULE_QUIRK_HDQ1W), SYSC_QUIRK("hdq1w", 0, 0, 0x14, 0x18, 0x0000000a, 0xffffffff, @@ -1362,22 +1269,12 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_MODULE_QUIRK_I2C), SYSC_QUIRK("i2c", 0, 0, 0x10, 0x90, 0x5040000a, 0xfffff0f0, SYSC_MODULE_QUIRK_I2C), - SYSC_QUIRK("gpu", 0x50000000, 0x14, -ENODEV, -ENODEV, 0x00010201, 0xffffffff, 0), - SYSC_QUIRK("gpu", 0x50000000, 0xfe00, 0xfe10, -ENODEV, 0x40000000 , 0xffffffff, + SYSC_QUIRK("gpu", 0x50000000, 0x14, -1, -1, 0x00010201, 0xffffffff, 0), + SYSC_QUIRK("gpu", 0x50000000, 0xfe00, 0xfe10, -1, 0x40000000 , 0xffffffff, SYSC_MODULE_QUIRK_SGX), - SYSC_QUIRK("rtc", 0, 0x74, 0x78, -ENODEV, 0x4eb01908, 0xffff00f0, - SYSC_MODULE_QUIRK_RTC_UNLOCK), - SYSC_QUIRK("tptc", 0, 0, 0x10, -ENODEV, 0x40006c00, 0xffffefff, - SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), - SYSC_QUIRK("tptc", 0, 0, -ENODEV, -ENODEV, 0x40007c00, 0xffffffff, - SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), - SYSC_QUIRK("usb_host_hs", 0, 0, 0x10, 0x14, 0x50700100, 0xffffffff, - SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), - SYSC_QUIRK("usb_host_hs", 0, 0, 0x10, -ENODEV, 0x50700101, 0xffffffff, - SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), SYSC_QUIRK("usb_otg_hs", 0, 0x400, 0x404, 0x408, 0x00000050, 0xffffffff, SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), - SYSC_QUIRK("usb_otg_hs", 0, 0, 0x10, -ENODEV, 0x4ea2080d, 0xffffffff, + SYSC_QUIRK("usb_otg_hs", 0, 0, 0x10, -1, 0x4ea2080d, 0xffffffff, SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY), SYSC_QUIRK("wdt", 0, 0, 0x10, 0x14, 0x502a0500, 0xfffff0f0, SYSC_MODULE_QUIRK_WDT), @@ -1386,66 +1283,57 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_MODULE_QUIRK_WDT | SYSC_QUIRK_SWSUP_SIDLE), #ifdef DEBUG - SYSC_QUIRK("adc", 0, 0, 0x10, -ENODEV, 0x47300001, 0xffffffff, 0), - SYSC_QUIRK("atl", 0, 0, -ENODEV, -ENODEV, 0x0a070100, 0xffffffff, 0), - SYSC_QUIRK("cm", 0, 0, -ENODEV, -ENODEV, 0x40000301, 0xffffffff, 0), - SYSC_QUIRK("control", 0, 0, 0x10, -ENODEV, 0x40000900, 0xffffffff, 0), + SYSC_QUIRK("adc", 0, 0, 0x10, -1, 0x47300001, 0xffffffff, 0), + SYSC_QUIRK("atl", 0, 0, -1, -1, 0x0a070100, 0xffffffff, 0), + SYSC_QUIRK("cm", 0, 0, -1, -1, 0x40000301, 0xffffffff, 0), + SYSC_QUIRK("control", 0, 0, 0x10, -1, 0x40000900, 0xffffffff, 0), SYSC_QUIRK("cpgmac", 0, 0x1200, 0x1208, 0x1204, 0x4edb1902, 0xffff00f0, 0), - SYSC_QUIRK("dcan", 0, 0x20, -ENODEV, -ENODEV, 0xa3170504, 0xffffffff, 0), - SYSC_QUIRK("dcan", 0, 0x20, -ENODEV, -ENODEV, 0x4edb1902, 0xffffffff, 0), - SYSC_QUIRK("dispc", 0x4832a400, 0, 0x10, 0x14, 0x00000030, 0xffffffff, 0), - SYSC_QUIRK("dispc", 0x58001000, 0, 0x10, 0x14, 0x00000040, 0xffffffff, 0), - SYSC_QUIRK("dispc", 0x58001000, 0, 0x10, 0x14, 0x00000051, 0xffffffff, 0), - SYSC_QUIRK("dmic", 0, 0, 0x10, -ENODEV, 0x50010000, 0xffffffff, 0), - SYSC_QUIRK("dsi", 0x58004000, 0, 0x10, 0x14, 0x00000030, 0xffffffff, 0), - SYSC_QUIRK("dsi", 0x58005000, 0, 0x10, 0x14, 0x00000030, 0xffffffff, 0), - SYSC_QUIRK("dsi", 0x58005000, 0, 0x10, 0x14, 0x00000040, 0xffffffff, 0), - SYSC_QUIRK("dsi", 0x58009000, 0, 0x10, 0x14, 0x00000040, 0xffffffff, 0), - SYSC_QUIRK("dwc3", 0, 0, 0x10, -ENODEV, 0x500a0200, 0xffffffff, 0), + SYSC_QUIRK("dcan", 0, 0x20, -1, -1, 0xa3170504, 0xffffffff, 0), + SYSC_QUIRK("dcan", 0, 0x20, -1, -1, 0x4edb1902, 0xffffffff, 0), + SYSC_QUIRK("dmic", 0, 0, 0x10, -1, 0x50010000, 0xffffffff, 0), + SYSC_QUIRK("dwc3", 0, 0, 0x10, -1, 0x500a0200, 0xffffffff, 0), SYSC_QUIRK("d2d", 0x4a0b6000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), SYSC_QUIRK("d2d", 0x4a0cd000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), - SYSC_QUIRK("epwmss", 0, 0, 0x4, -ENODEV, 0x47400001, 0xffffffff, 0), - SYSC_QUIRK("gpu", 0, 0x1fc00, 0x1fc10, -ENODEV, 0, 0, 0), - SYSC_QUIRK("gpu", 0, 0xfe00, 0xfe10, -ENODEV, 0x40000000 , 0xffffffff, 0), - SYSC_QUIRK("hdmi", 0, 0, 0x10, -ENODEV, 0x50031d00, 0xffffffff, 0), + SYSC_QUIRK("epwmss", 0, 0, 0x4, -1, 0x47400001, 0xffffffff, 0), + SYSC_QUIRK("gpu", 0, 0x1fc00, 0x1fc10, -1, 0, 0, 0), + SYSC_QUIRK("gpu", 0, 0xfe00, 0xfe10, -1, 0x40000000 , 0xffffffff, 0), SYSC_QUIRK("hsi", 0, 0, 0x10, 0x14, 0x50043101, 0xffffffff, 0), - SYSC_QUIRK("iss", 0, 0, 0x10, -ENODEV, 0x40000101, 0xffffffff, 0), - SYSC_QUIRK("lcdc", 0, 0, 0x54, -ENODEV, 0x4f201000, 0xffffffff, 0), - SYSC_QUIRK("mcasp", 0, 0, 0x4, -ENODEV, 0x44306302, 0xffffffff, 0), - SYSC_QUIRK("mcasp", 0, 0, 0x4, -ENODEV, 0x44307b02, 0xffffffff, 0), - SYSC_QUIRK("mcbsp", 0, -ENODEV, 0x8c, -ENODEV, 0, 0, 0), - SYSC_QUIRK("mcspi", 0, 0, 0x10, -ENODEV, 0x40300a0b, 0xffff00ff, 0), + SYSC_QUIRK("iss", 0, 0, 0x10, -1, 0x40000101, 0xffffffff, 0), + SYSC_QUIRK("lcdc", 0, 0, 0x54, -1, 0x4f201000, 0xffffffff, 0), + SYSC_QUIRK("mcasp", 0, 0, 0x4, -1, 0x44306302, 0xffffffff, 0), + SYSC_QUIRK("mcasp", 0, 0, 0x4, -1, 0x44307b02, 0xffffffff, 0), + SYSC_QUIRK("mcbsp", 0, -1, 0x8c, -1, 0, 0, 0), + SYSC_QUIRK("mcspi", 0, 0, 0x10, -1, 0x40300a0b, 0xffff00ff, 0), SYSC_QUIRK("mcspi", 0, 0, 0x110, 0x114, 0x40300a0b, 0xffffffff, 0), - SYSC_QUIRK("mailbox", 0, 0, 0x10, -ENODEV, 0x00000400, 0xffffffff, 0), - SYSC_QUIRK("m3", 0, 0, -ENODEV, -ENODEV, 0x5f580105, 0x0fff0f00, 0), + SYSC_QUIRK("mailbox", 0, 0, 0x10, -1, 0x00000400, 0xffffffff, 0), + SYSC_QUIRK("m3", 0, 0, -1, -1, 0x5f580105, 0x0fff0f00, 0), SYSC_QUIRK("ocp2scp", 0, 0, 0x10, 0x14, 0x50060005, 0xfffffff0, 0), - SYSC_QUIRK("ocp2scp", 0, 0, -ENODEV, -ENODEV, 0x50060007, 0xffffffff, 0), - SYSC_QUIRK("padconf", 0, 0, 0x10, -ENODEV, 0x4fff0800, 0xffffffff, 0), - SYSC_QUIRK("padconf", 0, 0, -ENODEV, -ENODEV, 0x40001100, 0xffffffff, 0), - SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x40000100, 0xffffffff, 0), - SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x00004102, 0xffffffff, 0), - SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x40000400, 0xffffffff, 0), - SYSC_QUIRK("rfbi", 0x4832a800, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), - SYSC_QUIRK("rfbi", 0x58002000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), - SYSC_QUIRK("scm", 0, 0, 0x10, -ENODEV, 0x40000900, 0xffffffff, 0), - SYSC_QUIRK("scm", 0, 0, -ENODEV, -ENODEV, 0x4e8b0100, 0xffffffff, 0), - SYSC_QUIRK("scm", 0, 0, -ENODEV, -ENODEV, 0x4f000100, 0xffffffff, 0), - SYSC_QUIRK("scm", 0, 0, -ENODEV, -ENODEV, 0x40000900, 0xffffffff, 0), - SYSC_QUIRK("scrm", 0, 0, -ENODEV, -ENODEV, 0x00000010, 0xffffffff, 0), - SYSC_QUIRK("sdio", 0, 0, 0x10, -ENODEV, 0x40202301, 0xffff0ff0, 0), + SYSC_QUIRK("ocp2scp", 0, 0, -1, -1, 0x50060007, 0xffffffff, 0), + SYSC_QUIRK("padconf", 0, 0, 0x10, -1, 0x4fff0800, 0xffffffff, 0), + SYSC_QUIRK("padconf", 0, 0, -1, -1, 0x40001100, 0xffffffff, 0), + SYSC_QUIRK("prcm", 0, 0, -1, -1, 0x40000100, 0xffffffff, 0), + SYSC_QUIRK("prcm", 0, 0, -1, -1, 0x00004102, 0xffffffff, 0), + SYSC_QUIRK("prcm", 0, 0, -1, -1, 0x40000400, 0xffffffff, 0), + SYSC_QUIRK("scm", 0, 0, 0x10, -1, 0x40000900, 0xffffffff, 0), + SYSC_QUIRK("scm", 0, 0, -1, -1, 0x4e8b0100, 0xffffffff, 0), + SYSC_QUIRK("scm", 0, 0, -1, -1, 0x4f000100, 0xffffffff, 0), + SYSC_QUIRK("scm", 0, 0, -1, -1, 0x40000900, 0xffffffff, 0), + SYSC_QUIRK("scrm", 0, 0, -1, -1, 0x00000010, 0xffffffff, 0), + SYSC_QUIRK("sdio", 0, 0, 0x10, -1, 0x40202301, 0xffff0ff0, 0), SYSC_QUIRK("sdio", 0, 0x2fc, 0x110, 0x114, 0x31010000, 0xffffffff, 0), SYSC_QUIRK("sdma", 0, 0, 0x2c, 0x28, 0x00010900, 0xffffffff, 0), - SYSC_QUIRK("slimbus", 0, 0, 0x10, -ENODEV, 0x40000902, 0xffffffff, 0), - SYSC_QUIRK("slimbus", 0, 0, 0x10, -ENODEV, 0x40002903, 0xffffffff, 0), - SYSC_QUIRK("spinlock", 0, 0, 0x10, -ENODEV, 0x50020000, 0xffffffff, 0), - SYSC_QUIRK("rng", 0, 0x1fe0, 0x1fe4, -ENODEV, 0x00000020, 0xffffffff, 0), - SYSC_QUIRK("timer32k", 0, 0, 0x4, -ENODEV, 0x00000060, 0xffffffff, 0), - SYSC_QUIRK("tpcc", 0, 0, -ENODEV, -ENODEV, 0x40014c00, 0xffffffff, 0), + SYSC_QUIRK("slimbus", 0, 0, 0x10, -1, 0x40000902, 0xffffffff, 0), + SYSC_QUIRK("slimbus", 0, 0, 0x10, -1, 0x40002903, 0xffffffff, 0), + SYSC_QUIRK("spinlock", 0, 0, 0x10, -1, 0x50020000, 0xffffffff, 0), + SYSC_QUIRK("rng", 0, 0x1fe0, 0x1fe4, -1, 0x00000020, 0xffffffff, 0), + SYSC_QUIRK("rtc", 0, 0x74, 0x78, -1, 0x4eb01908, 0xffff00f0, 0), + SYSC_QUIRK("timer32k", 0, 0, 0x4, -1, 0x00000060, 0xffffffff, 0), SYSC_QUIRK("usbhstll", 0, 0, 0x10, 0x14, 0x00000004, 0xffffffff, 0), SYSC_QUIRK("usbhstll", 0, 0, 0x10, 0x14, 0x00000008, 0xffffffff, 0), - SYSC_QUIRK("venc", 0x58003000, 0, -ENODEV, -ENODEV, 0x00000002, 0xffffffff, 0), - SYSC_QUIRK("vfpe", 0, 0, 0x104, -ENODEV, 0x4d001200, 0xffffffff, 0), + SYSC_QUIRK("usb_host_hs", 0, 0, 0x10, 0x14, 0x50700100, 0xffffffff, 0), + SYSC_QUIRK("usb_host_hs", 0, 0, 0x10, -1, 0x50700101, 0xffffffff, 0), + SYSC_QUIRK("vfpe", 0, 0, 0x104, -1, 0x4d001200, 0xffffffff, 0), #endif }; @@ -1467,13 +1355,16 @@ static void sysc_init_early_quirks(struct sysc *ddata) if (q->base != ddata->module_pa) continue; - if (q->rev_offset != ddata->offsets[SYSC_REVISION]) + if (q->rev_offset >= 0 && + q->rev_offset != ddata->offsets[SYSC_REVISION]) continue; - if (q->sysc_offset != ddata->offsets[SYSC_SYSCONFIG]) + if (q->sysc_offset >= 0 && + q->sysc_offset != ddata->offsets[SYSC_SYSCONFIG]) continue; - if (q->syss_offset != ddata->offsets[SYSC_SYSSTATUS]) + if (q->syss_offset >= 0 && + q->syss_offset != ddata->offsets[SYSC_SYSSTATUS]) continue; ddata->name = q->name; @@ -1493,13 +1384,16 @@ static void sysc_init_revision_quirks(struct sysc *ddata) if (q->base && q->base != ddata->module_pa) continue; - if (q->rev_offset != ddata->offsets[SYSC_REVISION]) + if (q->rev_offset >= 0 && + q->rev_offset != ddata->offsets[SYSC_REVISION]) continue; - if (q->sysc_offset != ddata->offsets[SYSC_SYSCONFIG]) + if (q->sysc_offset >= 0 && + q->sysc_offset != ddata->offsets[SYSC_SYSCONFIG]) continue; - if (q->syss_offset != ddata->offsets[SYSC_SYSSTATUS]) + if (q->syss_offset >= 0 && + q->syss_offset != ddata->offsets[SYSC_SYSSTATUS]) continue; if (q->revision == ddata->revision || @@ -1530,7 +1424,7 @@ static void sysc_module_enable_quirk_aess(struct sysc *ddata) sysc_write(ddata, offset, 1); } -/* I2C needs to be disabled for reset */ +/* I2C needs extra enable bit toggling for reset */ static void sysc_clk_quirk_i2c(struct sysc *ddata, bool enable) { int offset; @@ -1551,48 +1445,14 @@ static void sysc_clk_quirk_i2c(struct sysc *ddata, bool enable) sysc_write(ddata, offset, val); } -static void sysc_pre_reset_quirk_i2c(struct sysc *ddata) -{ - sysc_clk_quirk_i2c(ddata, false); -} - -static void sysc_post_reset_quirk_i2c(struct sysc *ddata) +static void sysc_clk_enable_quirk_i2c(struct sysc *ddata) { sysc_clk_quirk_i2c(ddata, true); } -/* RTC on am3 and 4 needs to be unlocked and locked for sysconfig */ -static void sysc_quirk_rtc(struct sysc *ddata, bool lock) +static void sysc_clk_disable_quirk_i2c(struct sysc *ddata) { - u32 val, kick0_val = 0, kick1_val = 0; - unsigned long flags; - int error; - - if (!lock) { - kick0_val = 0x83e70b13; - kick1_val = 0x95a4f1e0; - } - - local_irq_save(flags); - /* RTC_STATUS BUSY bit may stay active for 1/32768 seconds (~30 usec) */ - error = readl_poll_timeout_atomic(ddata->module_va + 0x44, val, - !(val & BIT(0)), 100, 50); - if (error) - dev_warn(ddata->dev, "rtc busy timeout\n"); - /* Now we have ~15 microseconds to read/write various registers */ - sysc_write(ddata, 0x6c, kick0_val); - sysc_write(ddata, 0x70, kick1_val); - local_irq_restore(flags); -} - -static void sysc_module_unlock_quirk_rtc(struct sysc *ddata) -{ - sysc_quirk_rtc(ddata, false); -} - -static void sysc_module_lock_quirk_rtc(struct sysc *ddata) -{ - sysc_quirk_rtc(ddata, true); + sysc_clk_quirk_i2c(ddata, false); } /* 36xx SGX needs a quirk for to bypass OCP IPG interrupt logic */ @@ -1634,14 +1494,14 @@ static void sysc_init_module_quirks(struct sysc *ddata) return; if (ddata->cfg.quirks & SYSC_MODULE_QUIRK_HDQ1W) { - ddata->pre_reset_quirk = sysc_pre_reset_quirk_hdq1w; + ddata->clk_disable_quirk = sysc_pre_reset_quirk_hdq1w; return; } if (ddata->cfg.quirks & SYSC_MODULE_QUIRK_I2C) { - ddata->pre_reset_quirk = sysc_pre_reset_quirk_i2c; - ddata->post_reset_quirk = sysc_post_reset_quirk_i2c; + ddata->clk_enable_quirk = sysc_clk_enable_quirk_i2c; + ddata->clk_disable_quirk = sysc_clk_disable_quirk_i2c; return; } @@ -1649,13 +1509,6 @@ static void sysc_init_module_quirks(struct sysc *ddata) if (ddata->cfg.quirks & SYSC_MODULE_QUIRK_AESS) ddata->module_enable_quirk = sysc_module_enable_quirk_aess; - if (ddata->cfg.quirks & SYSC_MODULE_QUIRK_RTC_UNLOCK) { - ddata->module_unlock_quirk = sysc_module_unlock_quirk_rtc; - ddata->module_lock_quirk = sysc_module_lock_quirk_rtc; - - return; - } - if (ddata->cfg.quirks & SYSC_MODULE_QUIRK_SGX) ddata->module_enable_quirk = sysc_module_enable_quirk_sgx; @@ -1712,47 +1565,17 @@ static int sysc_legacy_init(struct sysc *ddata) return error; } -/** - * sysc_rstctrl_reset_deassert - deassert rstctrl reset - * @ddata: device driver data - * @reset: reset before deassert - * - * A module can have both OCP softreset control and external rstctrl. - * If more complicated rstctrl resets are needed, please handle these - * directly from the child device driver and map only the module reset - * for the parent interconnect target module device. - * - * Automatic reset of the module on init can be skipped with the - * "ti,no-reset-on-init" device tree property. - */ -static int sysc_rstctrl_reset_deassert(struct sysc *ddata, bool reset) -{ - int error; - - if (!ddata->rsts) - return 0; - - if (reset) { - error = reset_control_assert(ddata->rsts); - if (error) - return error; - } - - reset_control_deassert(ddata->rsts); - - return 0; -} - /* * Note that the caller must ensure the interconnect target module is enabled * before calling reset. Otherwise reset will not complete. */ static int sysc_reset(struct sysc *ddata) { - int sysc_offset, sysc_val, error; - u32 sysc_mask; + int sysc_offset, syss_offset, sysc_val, rstval, error = 0; + u32 sysc_mask, syss_done; sysc_offset = ddata->offsets[SYSC_SYSCONFIG]; + syss_offset = ddata->offsets[SYSC_SYSSTATUS]; if (ddata->legacy_mode || sysc_offset < 0 || ddata->cap->regbits->srst_shift < 0 || @@ -1761,8 +1584,13 @@ static int sysc_reset(struct sysc *ddata) sysc_mask = BIT(ddata->cap->regbits->srst_shift); - if (ddata->pre_reset_quirk) - ddata->pre_reset_quirk(ddata); + if (ddata->cfg.quirks & SYSS_QUIRK_RESETDONE_INVERTED) + syss_done = 0; + else + syss_done = ddata->cfg.syss_mask; + + if (ddata->clk_disable_quirk) + ddata->clk_disable_quirk(ddata); sysc_val = sysc_read_sysconfig(ddata); sysc_val |= sysc_mask; @@ -1772,12 +1600,21 @@ static int sysc_reset(struct sysc *ddata) usleep_range(ddata->cfg.srst_udelay, ddata->cfg.srst_udelay * 2); - if (ddata->post_reset_quirk) - ddata->post_reset_quirk(ddata); + if (ddata->clk_enable_quirk) + ddata->clk_enable_quirk(ddata); - error = sysc_wait_softreset(ddata); - if (error) - dev_warn(ddata->dev, "OCP softreset timed out\n"); + /* Poll on reset status */ + if (syss_offset >= 0) { + error = readx_poll_timeout(sysc_read_sysstatus, ddata, rstval, + (rstval & ddata->cfg.syss_mask) == + syss_done, + 100, MAX_MODULE_SOFTRESET_WAIT); + + } else if (ddata->cfg.quirks & SYSC_QUIRK_RESET_STATUS) { + error = readx_poll_timeout(sysc_read_sysconfig, ddata, rstval, + !(rstval & sysc_mask), + 100, MAX_MODULE_SOFTRESET_WAIT); + } if (ddata->reset_done_quirk) ddata->reset_done_quirk(ddata); @@ -1794,15 +1631,6 @@ static int sysc_reset(struct sysc *ddata) static int sysc_init_module(struct sysc *ddata) { int error = 0; - bool manage_clocks = true; - - error = sysc_rstctrl_reset_deassert(ddata, false); - if (error) - return error; - - if (ddata->cfg.quirks & - (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT)) - manage_clocks = false; error = sysc_clockdomain_init(ddata); if (error) @@ -1823,7 +1651,7 @@ static int sysc_init_module(struct sysc *ddata) goto err_opt_clocks; if (!(ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)) { - error = sysc_rstctrl_reset_deassert(ddata, true); + error = reset_control_deassert(ddata->rsts); if (error) goto err_main_clocks; } @@ -1835,28 +1663,32 @@ static int sysc_init_module(struct sysc *ddata) if (ddata->legacy_mode) { error = sysc_legacy_init(ddata); if (error) - goto err_main_clocks; + goto err_reset; } if (!ddata->legacy_mode) { error = sysc_enable_module(ddata->dev); if (error) - goto err_main_clocks; + goto err_reset; } error = sysc_reset(ddata); if (error) dev_err(ddata->dev, "Reset failed with %d\n", error); - if (!ddata->legacy_mode && manage_clocks) + if (error && !ddata->legacy_mode) sysc_disable_module(ddata->dev); +err_reset: + if (error && !(ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)) + reset_control_assert(ddata->rsts); + err_main_clocks: - if (manage_clocks) + if (error) sysc_disable_main_clocks(ddata); err_opt_clocks: /* No re-enable of clockdomain autoidle to prevent module autoidle */ - if (manage_clocks) { + if (error) { sysc_disable_opt_clocks(ddata); sysc_clkdm_allow_idle(ddata); } @@ -1963,9 +1795,8 @@ static int sysc_child_add_named_clock(struct sysc *ddata, clk = clk_get(child, name); if (!IS_ERR(clk)) { - clk_put(clk); - - return -EEXIST; + error = -EEXIST; + goto put_clk; } clk = clk_get(ddata->dev, name); @@ -1975,7 +1806,7 @@ static int sysc_child_add_named_clock(struct sysc *ddata, l = clkdev_create(clk, name, dev_name(child)); if (!l) error = -ENOMEM; - +put_clk: clk_put(clk); return error; @@ -2629,10 +2460,17 @@ static int sysc_probe(struct platform_device *pdev) goto unprepare; } - /* Balance reset counts */ - if (ddata->rsts) + /* Balance use counts as PM runtime should have enabled these all */ + if (!(ddata->cfg.quirks & SYSC_QUIRK_NO_RESET_ON_INIT)) reset_control_assert(ddata->rsts); + if (!(ddata->cfg.quirks & + (SYSC_QUIRK_NO_IDLE | SYSC_QUIRK_NO_IDLE_ON_INIT))) { + sysc_disable_main_clocks(ddata); + sysc_disable_opt_clocks(ddata); + sysc_clkdm_allow_idle(ddata); + } + sysc_show_registers(ddata); ddata->dev->type = &sysc_device_type; diff --git a/drivers/counter/104-quad-8.c b/drivers/counter/104-quad-8.c index 5c23a9a..17e67a8 100644 --- a/drivers/counter/104-quad-8.c +++ b/drivers/counter/104-quad-8.c @@ -42,7 +42,6 @@ MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses"); * @base: base port address of the IIO device */ struct quad8_iio { - struct mutex lock; struct counter_device counter; unsigned int preset[QUAD8_NUM_COUNTERS]; unsigned int count_mode[QUAD8_NUM_COUNTERS]; @@ -117,8 +116,6 @@ static int quad8_read_raw(struct iio_dev *indio_dev, /* Borrow XOR Carry effectively doubles count range */ *val = (borrow ^ carry) << 24; - mutex_lock(&priv->lock); - /* Reset Byte Pointer; transfer Counter to Output Latch */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP | QUAD8_RLD_CNTR_OUT, base_offset + 1); @@ -126,8 +123,6 @@ static int quad8_read_raw(struct iio_dev *indio_dev, for (i = 0; i < 3; i++) *val |= (unsigned int)inb(base_offset) << (8 * i); - mutex_unlock(&priv->lock); - return IIO_VAL_INT; case IIO_CHAN_INFO_ENABLE: *val = priv->ab_enable[chan->channel]; @@ -158,8 +153,6 @@ static int quad8_write_raw(struct iio_dev *indio_dev, if ((unsigned int)val > 0xFFFFFF) return -EINVAL; - mutex_lock(&priv->lock); - /* Reset Byte Pointer */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP, base_offset + 1); @@ -183,16 +176,12 @@ static int quad8_write_raw(struct iio_dev *indio_dev, /* Reset Error flag */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_E, base_offset + 1); - mutex_unlock(&priv->lock); - return 0; case IIO_CHAN_INFO_ENABLE: /* only boolean values accepted */ if (val < 0 || val > 1) return -EINVAL; - mutex_lock(&priv->lock); - priv->ab_enable[chan->channel] = val; ior_cfg = val | priv->preset_enable[chan->channel] << 1; @@ -200,18 +189,11 @@ static int quad8_write_raw(struct iio_dev *indio_dev, /* Load I/O control configuration */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset + 1); - mutex_unlock(&priv->lock); - return 0; case IIO_CHAN_INFO_SCALE: - mutex_lock(&priv->lock); - /* Quadrature scaling only available in quadrature mode */ - if (!priv->quadrature_mode[chan->channel] && - (val2 || val != 1)) { - mutex_unlock(&priv->lock); + if (!priv->quadrature_mode[chan->channel] && (val2 || val != 1)) return -EINVAL; - } /* Only three gain states (1, 0.5, 0.25) */ if (val == 1 && !val2) @@ -225,15 +207,11 @@ static int quad8_write_raw(struct iio_dev *indio_dev, priv->quadrature_scale[chan->channel] = 2; break; default: - mutex_unlock(&priv->lock); return -EINVAL; } - else { - mutex_unlock(&priv->lock); + else return -EINVAL; - } - mutex_unlock(&priv->lock); return 0; } @@ -270,8 +248,6 @@ static ssize_t quad8_write_preset(struct iio_dev *indio_dev, uintptr_t private, if (preset > 0xFFFFFF) return -EINVAL; - mutex_lock(&priv->lock); - priv->preset[chan->channel] = preset; /* Reset Byte Pointer */ @@ -281,8 +257,6 @@ static ssize_t quad8_write_preset(struct iio_dev *indio_dev, uintptr_t private, for (i = 0; i < 3; i++) outb(preset >> (8 * i), base_offset); - mutex_unlock(&priv->lock); - return len; } @@ -312,8 +286,6 @@ static ssize_t quad8_write_set_to_preset_on_index(struct iio_dev *indio_dev, /* Preset enable is active low in Input/Output Control register */ preset_enable = !preset_enable; - mutex_lock(&priv->lock); - priv->preset_enable[chan->channel] = preset_enable; ior_cfg = priv->ab_enable[chan->channel] | @@ -322,8 +294,6 @@ static ssize_t quad8_write_set_to_preset_on_index(struct iio_dev *indio_dev, /* Load I/O control configuration to Input / Output Control Register */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset); - mutex_unlock(&priv->lock); - return len; } @@ -381,8 +351,6 @@ static int quad8_set_count_mode(struct iio_dev *indio_dev, unsigned int mode_cfg = cnt_mode << 1; const int base_offset = priv->base + 2 * chan->channel + 1; - mutex_lock(&priv->lock); - priv->count_mode[chan->channel] = cnt_mode; /* Add quadrature mode configuration */ @@ -392,8 +360,6 @@ static int quad8_set_count_mode(struct iio_dev *indio_dev, /* Load mode configuration to Counter Mode Register */ outb(QUAD8_CTR_CMR | mode_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -421,26 +387,19 @@ static int quad8_set_synchronous_mode(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, unsigned int synchronous_mode) { struct quad8_iio *const priv = iio_priv(indio_dev); + const unsigned int idr_cfg = synchronous_mode | + priv->index_polarity[chan->channel] << 1; const int base_offset = priv->base + 2 * chan->channel + 1; - unsigned int idr_cfg = synchronous_mode; - - mutex_lock(&priv->lock); - - idr_cfg |= priv->index_polarity[chan->channel] << 1; /* Index function must be non-synchronous in non-quadrature mode */ - if (synchronous_mode && !priv->quadrature_mode[chan->channel]) { - mutex_unlock(&priv->lock); + if (synchronous_mode && !priv->quadrature_mode[chan->channel]) return -EINVAL; - } priv->synchronous_mode[chan->channel] = synchronous_mode; /* Load Index Control configuration to Index Control Register */ outb(QUAD8_CTR_IDR | idr_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -468,12 +427,8 @@ static int quad8_set_quadrature_mode(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, unsigned int quadrature_mode) { struct quad8_iio *const priv = iio_priv(indio_dev); + unsigned int mode_cfg = priv->count_mode[chan->channel] << 1; const int base_offset = priv->base + 2 * chan->channel + 1; - unsigned int mode_cfg; - - mutex_lock(&priv->lock); - - mode_cfg = priv->count_mode[chan->channel] << 1; if (quadrature_mode) mode_cfg |= (priv->quadrature_scale[chan->channel] + 1) << 3; @@ -491,8 +446,6 @@ static int quad8_set_quadrature_mode(struct iio_dev *indio_dev, /* Load mode configuration to Counter Mode Register */ outb(QUAD8_CTR_CMR | mode_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -520,20 +473,15 @@ static int quad8_set_index_polarity(struct iio_dev *indio_dev, const struct iio_chan_spec *chan, unsigned int index_polarity) { struct quad8_iio *const priv = iio_priv(indio_dev); + const unsigned int idr_cfg = priv->synchronous_mode[chan->channel] | + index_polarity << 1; const int base_offset = priv->base + 2 * chan->channel + 1; - unsigned int idr_cfg = index_polarity << 1; - - mutex_lock(&priv->lock); - - idr_cfg |= priv->synchronous_mode[chan->channel]; priv->index_polarity[chan->channel] = index_polarity; /* Load Index Control configuration to Index Control Register */ outb(QUAD8_CTR_IDR | idr_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -614,11 +562,10 @@ static const struct iio_chan_spec quad8_channels[] = { }; static int quad8_signal_read(struct counter_device *counter, - struct counter_signal *signal, struct counter_signal_read_value *val) + struct counter_signal *signal, enum counter_signal_value *val) { const struct quad8_iio *const priv = counter->priv; unsigned int state; - enum counter_signal_level level; /* Only Index signal levels can be read */ if (signal->id < 16) @@ -627,22 +574,19 @@ static int quad8_signal_read(struct counter_device *counter, state = inb(priv->base + QUAD8_REG_INDEX_INPUT_LEVELS) & BIT(signal->id - 16); - level = (state) ? COUNTER_SIGNAL_LEVEL_HIGH : COUNTER_SIGNAL_LEVEL_LOW; - - counter_signal_read_value_set(val, COUNTER_SIGNAL_LEVEL, &level); + *val = (state) ? COUNTER_SIGNAL_HIGH : COUNTER_SIGNAL_LOW; return 0; } static int quad8_count_read(struct counter_device *counter, - struct counter_count *count, struct counter_count_read_value *val) + struct counter_count *count, unsigned long *val) { - struct quad8_iio *const priv = counter->priv; + const struct quad8_iio *const priv = counter->priv; const int base_offset = priv->base + 2 * count->id; unsigned int flags; unsigned int borrow; unsigned int carry; - unsigned long position; int i; flags = inb(base_offset + 1); @@ -650,50 +594,35 @@ static int quad8_count_read(struct counter_device *counter, carry = !!(flags & QUAD8_FLAG_CT); /* Borrow XOR Carry effectively doubles count range */ - position = (unsigned long)(borrow ^ carry) << 24; - - mutex_lock(&priv->lock); + *val = (unsigned long)(borrow ^ carry) << 24; /* Reset Byte Pointer; transfer Counter to Output Latch */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP | QUAD8_RLD_CNTR_OUT, base_offset + 1); for (i = 0; i < 3; i++) - position |= (unsigned long)inb(base_offset) << (8 * i); - - counter_count_read_value_set(val, COUNTER_COUNT_POSITION, &position); - - mutex_unlock(&priv->lock); + *val |= (unsigned long)inb(base_offset) << (8 * i); return 0; } static int quad8_count_write(struct counter_device *counter, - struct counter_count *count, struct counter_count_write_value *val) + struct counter_count *count, unsigned long val) { - struct quad8_iio *const priv = counter->priv; + const struct quad8_iio *const priv = counter->priv; const int base_offset = priv->base + 2 * count->id; - int err; - unsigned long position; int i; - err = counter_count_write_value_get(&position, COUNTER_COUNT_POSITION, - val); - if (err) - return err; - /* Only 24-bit values are supported */ - if (position > 0xFFFFFF) + if (val > 0xFFFFFF) return -EINVAL; - mutex_lock(&priv->lock); - /* Reset Byte Pointer */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP, base_offset + 1); /* Counter can only be set via Preset Register */ for (i = 0; i < 3; i++) - outb(position >> (8 * i), base_offset); + outb(val >> (8 * i), base_offset); /* Transfer Preset Register to Counter */ outb(QUAD8_CTR_RLD | QUAD8_RLD_PRESET_CNTR, base_offset + 1); @@ -702,17 +631,15 @@ static int quad8_count_write(struct counter_device *counter, outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP, base_offset + 1); /* Set Preset Register back to original value */ - position = priv->preset[count->id]; + val = priv->preset[count->id]; for (i = 0; i < 3; i++) - outb(position >> (8 * i), base_offset); + outb(val >> (8 * i), base_offset); /* Reset Borrow, Carry, Compare, and Sign flags */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_FLAGS, base_offset + 1); /* Reset Error flag */ outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_E, base_offset + 1); - mutex_unlock(&priv->lock); - return 0; } @@ -733,13 +660,13 @@ static enum counter_count_function quad8_count_functions_list[] = { static int quad8_function_get(struct counter_device *counter, struct counter_count *count, size_t *function) { - struct quad8_iio *const priv = counter->priv; + const struct quad8_iio *const priv = counter->priv; const int id = count->id; + const unsigned int quadrature_mode = priv->quadrature_mode[id]; + const unsigned int scale = priv->quadrature_scale[id]; - mutex_lock(&priv->lock); - - if (priv->quadrature_mode[id]) - switch (priv->quadrature_scale[id]) { + if (quadrature_mode) + switch (scale) { case 0: *function = QUAD8_COUNT_FUNCTION_QUADRATURE_X1; break; @@ -753,8 +680,6 @@ static int quad8_function_get(struct counter_device *counter, else *function = QUAD8_COUNT_FUNCTION_PULSE_DIRECTION; - mutex_unlock(&priv->lock); - return 0; } @@ -765,15 +690,10 @@ static int quad8_function_set(struct counter_device *counter, const int id = count->id; unsigned int *const quadrature_mode = priv->quadrature_mode + id; unsigned int *const scale = priv->quadrature_scale + id; + unsigned int mode_cfg = priv->count_mode[id] << 1; unsigned int *const synchronous_mode = priv->synchronous_mode + id; + const unsigned int idr_cfg = priv->index_polarity[id] << 1; const int base_offset = priv->base + 2 * id + 1; - unsigned int mode_cfg; - unsigned int idr_cfg; - - mutex_lock(&priv->lock); - - mode_cfg = priv->count_mode[id] << 1; - idr_cfg = priv->index_polarity[id] << 1; if (function == QUAD8_COUNT_FUNCTION_PULSE_DIRECTION) { *quadrature_mode = 0; @@ -809,8 +729,6 @@ static int quad8_function_set(struct counter_device *counter, /* Load mode configuration to Counter Mode Register */ outb(QUAD8_CTR_CMR | mode_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -927,20 +845,15 @@ static int quad8_index_polarity_set(struct counter_device *counter, { struct quad8_iio *const priv = counter->priv; const size_t channel_id = signal->id - 16; + const unsigned int idr_cfg = priv->synchronous_mode[channel_id] | + index_polarity << 1; const int base_offset = priv->base + 2 * channel_id + 1; - unsigned int idr_cfg = index_polarity << 1; - - mutex_lock(&priv->lock); - - idr_cfg |= priv->synchronous_mode[channel_id]; priv->index_polarity[channel_id] = index_polarity; /* Load Index Control configuration to Index Control Register */ outb(QUAD8_CTR_IDR | idr_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -967,26 +880,19 @@ static int quad8_synchronous_mode_set(struct counter_device *counter, { struct quad8_iio *const priv = counter->priv; const size_t channel_id = signal->id - 16; + const unsigned int idr_cfg = synchronous_mode | + priv->index_polarity[channel_id] << 1; const int base_offset = priv->base + 2 * channel_id + 1; - unsigned int idr_cfg = synchronous_mode; - - mutex_lock(&priv->lock); - - idr_cfg |= priv->index_polarity[channel_id] << 1; /* Index function must be non-synchronous in non-quadrature mode */ - if (synchronous_mode && !priv->quadrature_mode[channel_id]) { - mutex_unlock(&priv->lock); + if (synchronous_mode && !priv->quadrature_mode[channel_id]) return -EINVAL; - } priv->synchronous_mode[channel_id] = synchronous_mode; /* Load Index Control configuration to Index Control Register */ outb(QUAD8_CTR_IDR | idr_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -1051,8 +957,6 @@ static int quad8_count_mode_set(struct counter_device *counter, break; } - mutex_lock(&priv->lock); - priv->count_mode[count->id] = cnt_mode; /* Set count mode configuration value */ @@ -1065,8 +969,6 @@ static int quad8_count_mode_set(struct counter_device *counter, /* Load mode configuration to Counter Mode Register */ outb(QUAD8_CTR_CMR | mode_cfg, base_offset); - mutex_unlock(&priv->lock); - return 0; } @@ -1108,8 +1010,6 @@ static ssize_t quad8_count_enable_write(struct counter_device *counter, if (err) return err; - mutex_lock(&priv->lock); - priv->ab_enable[count->id] = ab_enable; ior_cfg = ab_enable | priv->preset_enable[count->id] << 1; @@ -1117,8 +1017,6 @@ static ssize_t quad8_count_enable_write(struct counter_device *counter, /* Load I/O control configuration */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset + 1); - mutex_unlock(&priv->lock); - return len; } @@ -1147,28 +1045,14 @@ static ssize_t quad8_count_preset_read(struct counter_device *counter, return sprintf(buf, "%u\n", priv->preset[count->id]); } -static void quad8_preset_register_set(struct quad8_iio *quad8iio, int id, - unsigned int preset) -{ - const unsigned int base_offset = quad8iio->base + 2 * id; - int i; - - quad8iio->preset[id] = preset; - - /* Reset Byte Pointer */ - outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP, base_offset + 1); - - /* Set Preset Register */ - for (i = 0; i < 3; i++) - outb(preset >> (8 * i), base_offset); -} - static ssize_t quad8_count_preset_write(struct counter_device *counter, struct counter_count *count, void *private, const char *buf, size_t len) { struct quad8_iio *const priv = counter->priv; + const int base_offset = priv->base + 2 * count->id; unsigned int preset; int ret; + int i; ret = kstrtouint(buf, 0, &preset); if (ret) @@ -1178,11 +1062,14 @@ static ssize_t quad8_count_preset_write(struct counter_device *counter, if (preset > 0xFFFFFF) return -EINVAL; - mutex_lock(&priv->lock); + priv->preset[count->id] = preset; - quad8_preset_register_set(priv, count->id, preset); + /* Reset Byte Pointer */ + outb(QUAD8_CTR_RLD | QUAD8_RLD_RESET_BP, base_offset + 1); - mutex_unlock(&priv->lock); + /* Set Preset Register */ + for (i = 0; i < 3; i++) + outb(preset >> (8 * i), base_offset); return len; } @@ -1190,20 +1077,15 @@ static ssize_t quad8_count_preset_write(struct counter_device *counter, static ssize_t quad8_count_ceiling_read(struct counter_device *counter, struct counter_count *count, void *private, char *buf) { - struct quad8_iio *const priv = counter->priv; - - mutex_lock(&priv->lock); + const struct quad8_iio *const priv = counter->priv; /* Range Limit and Modulo-N count modes use preset value as ceiling */ switch (priv->count_mode[count->id]) { case 1: case 3: - mutex_unlock(&priv->lock); - return sprintf(buf, "%u\n", priv->preset[count->id]); + return quad8_count_preset_read(counter, count, private, buf); } - mutex_unlock(&priv->lock); - /* By default 0x1FFFFFF (25 bits unsigned) is maximum count */ return sprintf(buf, "33554431\n"); } @@ -1212,29 +1094,15 @@ static ssize_t quad8_count_ceiling_write(struct counter_device *counter, struct counter_count *count, void *private, const char *buf, size_t len) { struct quad8_iio *const priv = counter->priv; - unsigned int ceiling; - int ret; - - ret = kstrtouint(buf, 0, &ceiling); - if (ret) - return ret; - - /* Only 24-bit values are supported */ - if (ceiling > 0xFFFFFF) - return -EINVAL; - - mutex_lock(&priv->lock); /* Range Limit and Modulo-N count modes use preset value as ceiling */ switch (priv->count_mode[count->id]) { case 1: case 3: - quad8_preset_register_set(priv, count->id, ceiling); - break; + return quad8_count_preset_write(counter, count, private, buf, + len); } - mutex_unlock(&priv->lock); - return len; } @@ -1262,8 +1130,6 @@ static ssize_t quad8_count_preset_enable_write(struct counter_device *counter, /* Preset enable is active low in Input/Output Control register */ preset_enable = !preset_enable; - mutex_lock(&priv->lock); - priv->preset_enable[count->id] = preset_enable; ior_cfg = priv->ab_enable[count->id] | (unsigned int)preset_enable << 1; @@ -1271,8 +1137,6 @@ static ssize_t quad8_count_preset_enable_write(struct counter_device *counter, /* Load I/O control configuration to Input / Output Control Register */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset); - mutex_unlock(&priv->lock); - return len; } @@ -1443,9 +1307,6 @@ static int quad8_probe(struct device *dev, unsigned int id) quad8iio->counter.priv = quad8iio; quad8iio->base = base[id]; - /* Initialize mutex */ - mutex_init(&quad8iio->lock); - /* Reset all counters and disable interrupt function */ outb(QUAD8_CHAN_OP_RESET_COUNTERS, base[id] + QUAD8_REG_CHAN_OP); /* Set initial configuration for all counters */ diff --git a/drivers/counter/Kconfig b/drivers/counter/Kconfig index 2967d0a..c80fa76 100644 --- a/drivers/counter/Kconfig +++ b/drivers/counter/Kconfig @@ -49,6 +49,17 @@ config STM32_LPTIMER_CNT To compile this driver as a module, choose M here: the module will be called stm32-lptimer-cnt. +config TI_EQEP + tristate "TI eQEP counter driver" + depends on (SOC_AM33XX || COMPILE_TEST) + select REGMAP_MMIO + help + Select this option to enable the Texas Instruments Enhanced Quadrature + Encoder Pulse (eQEP) counter driver. + + To compile this driver as a module, choose M here: the module will be + called ti-eqep. + config FTM_QUADDEC tristate "Flex Timer Module Quadrature decoder driver" depends on HAS_IOMEM && OF diff --git a/drivers/counter/Makefile b/drivers/counter/Makefile index 40d3552..55142d1 100644 --- a/drivers/counter/Makefile +++ b/drivers/counter/Makefile @@ -8,4 +8,5 @@ obj-$(CONFIG_COUNTER) += counter.o obj-$(CONFIG_104_QUAD_8) += 104-quad-8.o obj-$(CONFIG_STM32_TIMER_CNT) += stm32-timer-cnt.o obj-$(CONFIG_STM32_LPTIMER_CNT) += stm32-lptimer-cnt.o +obj-$(CONFIG_TI_EQEP) += ti-eqep.o obj-$(CONFIG_FTM_QUADDEC) += ftm-quaddec.o diff --git a/drivers/counter/counter.c b/drivers/counter/counter.c index 106bc71..6a683d0 100644 --- a/drivers/counter/counter.c +++ b/drivers/counter/counter.c @@ -220,86 +220,6 @@ ssize_t counter_device_enum_available_read(struct counter_device *counter, } EXPORT_SYMBOL_GPL(counter_device_enum_available_read); -static const char *const counter_signal_level_str[] = { - [COUNTER_SIGNAL_LEVEL_LOW] = "low", - [COUNTER_SIGNAL_LEVEL_HIGH] = "high" -}; - -/** - * counter_signal_read_value_set - set counter_signal_read_value data - * @val: counter_signal_read_value structure to set - * @type: property Signal data represents - * @data: Signal data - * - * This function sets an opaque counter_signal_read_value structure with the - * provided Signal data. - */ -void counter_signal_read_value_set(struct counter_signal_read_value *const val, - const enum counter_signal_value_type type, - void *const data) -{ - if (type == COUNTER_SIGNAL_LEVEL) - val->len = sprintf(val->buf, "%s\n", - counter_signal_level_str[*(enum counter_signal_level *)data]); - else - val->len = 0; -} -EXPORT_SYMBOL_GPL(counter_signal_read_value_set); - -/** - * counter_count_read_value_set - set counter_count_read_value data - * @val: counter_count_read_value structure to set - * @type: property Count data represents - * @data: Count data - * - * This function sets an opaque counter_count_read_value structure with the - * provided Count data. - */ -void counter_count_read_value_set(struct counter_count_read_value *const val, - const enum counter_count_value_type type, - void *const data) -{ - switch (type) { - case COUNTER_COUNT_POSITION: - val->len = sprintf(val->buf, "%lu\n", *(unsigned long *)data); - break; - default: - val->len = 0; - } -} -EXPORT_SYMBOL_GPL(counter_count_read_value_set); - -/** - * counter_count_write_value_get - get counter_count_write_value data - * @data: Count data - * @type: property Count data represents - * @val: counter_count_write_value structure containing data - * - * This function extracts Count data from the provided opaque - * counter_count_write_value structure and stores it at the address provided by - * @data. - * - * RETURNS: - * 0 on success, negative error number on failure. - */ -int counter_count_write_value_get(void *const data, - const enum counter_count_value_type type, - const struct counter_count_write_value *const val) -{ - int err; - - switch (type) { - case COUNTER_COUNT_POSITION: - err = kstrtoul(val->buf, 0, data); - if (err) - return err; - break; - } - - return 0; -} -EXPORT_SYMBOL_GPL(counter_count_write_value_get); - struct counter_attr_parm { struct counter_device_attr_group *group; const char *prefix; @@ -369,6 +289,11 @@ struct counter_signal_unit { struct counter_signal *signal; }; +static const char *const counter_signal_value_str[] = { + [COUNTER_SIGNAL_LOW] = "low", + [COUNTER_SIGNAL_HIGH] = "high" +}; + static ssize_t counter_signal_show(struct device *dev, struct device_attribute *attr, char *buf) { @@ -377,13 +302,13 @@ static ssize_t counter_signal_show(struct device *dev, const struct counter_signal_unit *const component = devattr->component; struct counter_signal *const signal = component->signal; int err; - struct counter_signal_read_value val = { .buf = buf }; + enum counter_signal_value val; err = counter->ops->signal_read(counter, signal, &val); if (err) return err; - return val.len; + return sprintf(buf, "%s\n", counter_signal_value_str[val]); } struct counter_name_unit { @@ -788,13 +713,13 @@ static ssize_t counter_count_show(struct device *dev, const struct counter_count_unit *const component = devattr->component; struct counter_count *const count = component->count; int err; - struct counter_count_read_value val = { .buf = buf }; + unsigned long val; err = counter->ops->count_read(counter, count, &val); if (err) return err; - return val.len; + return sprintf(buf, "%lu\n", val); } static ssize_t counter_count_store(struct device *dev, @@ -806,9 +731,13 @@ static ssize_t counter_count_store(struct device *dev, const struct counter_count_unit *const component = devattr->component; struct counter_count *const count = component->count; int err; - struct counter_count_write_value val = { .buf = buf }; + unsigned long val; + + err = kstrtoul(buf, 0, &val); + if (err) + return err; - err = counter->ops->count_write(counter, count, &val); + err = counter->ops->count_write(counter, count, val); if (err) return err; diff --git a/drivers/counter/ftm-quaddec.c b/drivers/counter/ftm-quaddec.c index 4046aa9..c2b3fdf 100644 --- a/drivers/counter/ftm-quaddec.c +++ b/drivers/counter/ftm-quaddec.c @@ -178,31 +178,25 @@ static const enum counter_count_function ftm_quaddec_count_functions[] = { static int ftm_quaddec_count_read(struct counter_device *counter, struct counter_count *count, - struct counter_count_read_value *val) + unsigned long *val) { struct ftm_quaddec *const ftm = counter->priv; uint32_t cntval; ftm_read(ftm, FTM_CNT, &cntval); - counter_count_read_value_set(val, COUNTER_COUNT_POSITION, &cntval); + *val = cntval; return 0; } static int ftm_quaddec_count_write(struct counter_device *counter, struct counter_count *count, - struct counter_count_write_value *val) + const unsigned long val) { struct ftm_quaddec *const ftm = counter->priv; - u32 cnt; - int err; - err = counter_count_write_value_get(&cnt, COUNTER_COUNT_POSITION, val); - if (err) - return err; - - if (cnt != 0) { + if (val != 0) { dev_warn(&ftm->pdev->dev, "Can only accept '0' as new counter value\n"); return -EINVAL; } diff --git a/drivers/counter/stm32-lptimer-cnt.c b/drivers/counter/stm32-lptimer-cnt.c index bbc930a..8e276eb 100644 --- a/drivers/counter/stm32-lptimer-cnt.c +++ b/drivers/counter/stm32-lptimer-cnt.c @@ -347,7 +347,7 @@ static const struct iio_chan_spec stm32_lptim_cnt_channels = { }; /** - * stm32_lptim_cnt_function - enumerates stm32 LPTimer counter & encoder modes + * enum stm32_lptim_cnt_function - enumerates LPTimer counter & encoder modes * @STM32_LPTIM_COUNTER_INCREASE: up count on IN1 rising, falling or both edges * @STM32_LPTIM_ENCODER_BOTH_EDGE: count on both edges (IN1 & IN2 quadrature) */ @@ -377,8 +377,7 @@ static enum counter_synapse_action stm32_lptim_cnt_synapse_actions[] = { }; static int stm32_lptim_cnt_read(struct counter_device *counter, - struct counter_count *count, - struct counter_count_read_value *val) + struct counter_count *count, unsigned long *val) { struct stm32_lptim_cnt *const priv = counter->priv; u32 cnt; @@ -388,7 +387,7 @@ static int stm32_lptim_cnt_read(struct counter_device *counter, if (ret) return ret; - counter_count_read_value_set(val, COUNTER_COUNT_POSITION, &cnt); + *val = cnt; return 0; } diff --git a/drivers/counter/stm32-timer-cnt.c b/drivers/counter/stm32-timer-cnt.c index 644ba18..3eafcce 100644 --- a/drivers/counter/stm32-timer-cnt.c +++ b/drivers/counter/stm32-timer-cnt.c @@ -28,7 +28,7 @@ struct stm32_timer_cnt { }; /** - * stm32_count_function - enumerates stm32 timer counter encoder modes + * enum stm32_count_function - enumerates stm32 timer counter encoder modes * @STM32_COUNT_SLAVE_MODE_DISABLED: counts on internal clock when CEN=1 * @STM32_COUNT_ENCODER_MODE_1: counts TI1FP1 edges, depending on TI2FP2 level * @STM32_COUNT_ENCODER_MODE_2: counts TI2FP2 edges, depending on TI1FP1 level @@ -48,34 +48,27 @@ static enum counter_count_function stm32_count_functions[] = { }; static int stm32_count_read(struct counter_device *counter, - struct counter_count *count, - struct counter_count_read_value *val) + struct counter_count *count, unsigned long *val) { struct stm32_timer_cnt *const priv = counter->priv; u32 cnt; regmap_read(priv->regmap, TIM_CNT, &cnt); - counter_count_read_value_set(val, COUNTER_COUNT_POSITION, &cnt); + *val = cnt; return 0; } static int stm32_count_write(struct counter_device *counter, struct counter_count *count, - struct counter_count_write_value *val) + const unsigned long val) { struct stm32_timer_cnt *const priv = counter->priv; - u32 cnt; - int err; - - err = counter_count_write_value_get(&cnt, COUNTER_COUNT_POSITION, val); - if (err) - return err; - if (cnt > priv->ceiling) + if (val > priv->ceiling) return -EINVAL; - return regmap_write(priv->regmap, TIM_CNT, cnt); + return regmap_write(priv->regmap, TIM_CNT, val); } static int stm32_count_function_get(struct counter_device *counter, @@ -219,8 +212,8 @@ static ssize_t stm32_count_enable_write(struct counter_device *counter, if (enable) { regmap_read(priv->regmap, TIM_CR1, &cr1); - if (!(cr1 & TIM_CR1_CEN)) - clk_enable(priv->clk); + if (!(cr1 & TIM_CR1_CEN)) + clk_enable(priv->clk); regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN); diff --git b/drivers/counter/ti-eqep.c b/drivers/counter/ti-eqep.c new file mode 100644 index 0000000..1ff07fa --- /dev/null +++ b/drivers/counter/ti-eqep.c @@ -0,0 +1,466 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2019 David Lechner + * + * Counter driver for Texas Instruments Enhanced Quadrature Encoder Pulse (eQEP) + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +/* 32-bit registers */ +#define QPOSCNT 0x0 +#define QPOSINIT 0x4 +#define QPOSMAX 0x8 +#define QPOSCMP 0xc +#define QPOSILAT 0x10 +#define QPOSSLAT 0x14 +#define QPOSLAT 0x18 +#define QUTMR 0x1c +#define QUPRD 0x20 + +/* 16-bit registers */ +#define QWDTMR 0x0 /* 0x24 */ +#define QWDPRD 0x2 /* 0x26 */ +#define QDECCTL 0x4 /* 0x28 */ +#define QEPCTL 0x6 /* 0x2a */ +#define QCAPCTL 0x8 /* 0x2c */ +#define QPOSCTL 0xa /* 0x2e */ +#define QEINT 0xc /* 0x30 */ +#define QFLG 0xe /* 0x32 */ +#define QCLR 0x10 /* 0x34 */ +#define QFRC 0x12 /* 0x36 */ +#define QEPSTS 0x14 /* 0x38 */ +#define QCTMR 0x16 /* 0x3a */ +#define QCPRD 0x18 /* 0x3c */ +#define QCTMRLAT 0x1a /* 0x3e */ +#define QCPRDLAT 0x1c /* 0x40 */ + +#define QDECCTL_QSRC_SHIFT 14 +#define QDECCTL_QSRC GENMASK(15, 14) +#define QDECCTL_SOEN BIT(13) +#define QDECCTL_SPSEL BIT(12) +#define QDECCTL_XCR BIT(11) +#define QDECCTL_SWAP BIT(10) +#define QDECCTL_IGATE BIT(9) +#define QDECCTL_QAP BIT(8) +#define QDECCTL_QBP BIT(7) +#define QDECCTL_QIP BIT(6) +#define QDECCTL_QSP BIT(5) + +#define QEPCTL_FREE_SOFT GENMASK(15, 14) +#define QEPCTL_PCRM GENMASK(13, 12) +#define QEPCTL_SEI GENMASK(11, 10) +#define QEPCTL_IEI GENMASK(9, 8) +#define QEPCTL_SWI BIT(7) +#define QEPCTL_SEL BIT(6) +#define QEPCTL_IEL GENMASK(5, 4) +#define QEPCTL_PHEN BIT(3) +#define QEPCTL_QCLM BIT(2) +#define QEPCTL_UTE BIT(1) +#define QEPCTL_WDE BIT(0) + +/* EQEP Inputs */ +enum { + TI_EQEP_SIGNAL_QEPA, /* QEPA/XCLK */ + TI_EQEP_SIGNAL_QEPB, /* QEPB/XDIR */ +}; + +/* Position Counter Input Modes */ +enum { + TI_EQEP_COUNT_FUNC_QUAD_COUNT, + TI_EQEP_COUNT_FUNC_DIR_COUNT, + TI_EQEP_COUNT_FUNC_UP_COUNT, + TI_EQEP_COUNT_FUNC_DOWN_COUNT, +}; + +enum { + TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES, + TI_EQEP_SYNAPSE_ACTION_RISING_EDGE, + TI_EQEP_SYNAPSE_ACTION_NONE, +}; + +struct ti_eqep_cnt { + struct counter_device counter; + struct regmap *regmap32; + struct regmap *regmap16; +}; + +static int ti_eqep_count_read(struct counter_device *counter, + struct counter_count *count, unsigned long *val) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 cnt; + + regmap_read(priv->regmap32, QPOSCNT, &cnt); + *val = cnt; + + return 0; +} + +static int ti_eqep_count_write(struct counter_device *counter, + struct counter_count *count, unsigned long val) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 max; + + regmap_read(priv->regmap32, QPOSMAX, &max); + if (val > max) + return -EINVAL; + + return regmap_write(priv->regmap32, QPOSCNT, val); +} + +static int ti_eqep_function_get(struct counter_device *counter, + struct counter_count *count, size_t *function) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 qdecctl; + + regmap_read(priv->regmap16, QDECCTL, &qdecctl); + *function = (qdecctl & QDECCTL_QSRC) >> QDECCTL_QSRC_SHIFT; + + return 0; +} + +static int ti_eqep_function_set(struct counter_device *counter, + struct counter_count *count, size_t function) +{ + struct ti_eqep_cnt *priv = counter->priv; + + return regmap_write_bits(priv->regmap16, QDECCTL, QDECCTL_QSRC, + function << QDECCTL_QSRC_SHIFT); +} + +static int ti_eqep_action_get(struct counter_device *counter, + struct counter_count *count, + struct counter_synapse *synapse, size_t *action) +{ + struct ti_eqep_cnt *priv = counter->priv; + size_t function; + u32 qdecctl; + int err; + + err = ti_eqep_function_get(counter, count, &function); + if (err) + return err; + + switch (function) { + case TI_EQEP_COUNT_FUNC_QUAD_COUNT: + /* In quadrature mode, the rising and falling edge of both + * QEPA and QEPB trigger QCLK. + */ + *action = TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES; + break; + case TI_EQEP_COUNT_FUNC_DIR_COUNT: + /* In direction-count mode only rising edge of QEPA is counted + * and QEPB gives direction. + */ + switch (synapse->signal->id) { + case TI_EQEP_SIGNAL_QEPA: + *action = TI_EQEP_SYNAPSE_ACTION_RISING_EDGE; + break; + default: + *action = TI_EQEP_SYNAPSE_ACTION_NONE; + break; + } + break; + case TI_EQEP_COUNT_FUNC_UP_COUNT: + case TI_EQEP_COUNT_FUNC_DOWN_COUNT: + /* In up/down-count modes only QEPA is counted and QEPB is not + * used. + */ + switch (synapse->signal->id) { + case TI_EQEP_SIGNAL_QEPA: + err = regmap_read(priv->regmap16, QDECCTL, &qdecctl); + if (err) + return err; + + if (qdecctl & QDECCTL_XCR) + *action = TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES; + else + *action = TI_EQEP_SYNAPSE_ACTION_RISING_EDGE; + break; + default: + *action = TI_EQEP_SYNAPSE_ACTION_NONE; + break; + } + break; + } + + return 0; +} + +static const struct counter_ops ti_eqep_counter_ops = { + .count_read = ti_eqep_count_read, + .count_write = ti_eqep_count_write, + .function_get = ti_eqep_function_get, + .function_set = ti_eqep_function_set, + .action_get = ti_eqep_action_get, +}; + +static ssize_t ti_eqep_position_ceiling_read(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, char *buf) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 qposmax; + + regmap_read(priv->regmap32, QPOSMAX, &qposmax); + + return sprintf(buf, "%u\n", qposmax); +} + +static ssize_t ti_eqep_position_ceiling_write(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, const char *buf, + size_t len) +{ + struct ti_eqep_cnt *priv = counter->priv; + int err; + u32 res; + + err = kstrtouint(buf, 0, &res); + if (err < 0) + return err; + + regmap_write(priv->regmap32, QPOSMAX, res); + + return len; +} + +static ssize_t ti_eqep_position_floor_read(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, char *buf) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 qposinit; + + regmap_read(priv->regmap32, QPOSINIT, &qposinit); + + return sprintf(buf, "%u\n", qposinit); +} + +static ssize_t ti_eqep_position_floor_write(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, const char *buf, + size_t len) +{ + struct ti_eqep_cnt *priv = counter->priv; + int err; + u32 res; + + err = kstrtouint(buf, 0, &res); + if (err < 0) + return err; + + regmap_write(priv->regmap32, QPOSINIT, res); + + return len; +} + +static ssize_t ti_eqep_position_enable_read(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, char *buf) +{ + struct ti_eqep_cnt *priv = counter->priv; + u32 qepctl; + + regmap_read(priv->regmap16, QEPCTL, &qepctl); + + return sprintf(buf, "%u\n", !!(qepctl & QEPCTL_PHEN)); +} + +static ssize_t ti_eqep_position_enable_write(struct counter_device *counter, + struct counter_count *count, + void *ext_priv, const char *buf, + size_t len) +{ + struct ti_eqep_cnt *priv = counter->priv; + int err; + bool res; + + err = kstrtobool(buf, &res); + if (err < 0) + return err; + + regmap_write_bits(priv->regmap16, QEPCTL, QEPCTL_PHEN, res ? -1 : 0); + + return len; +} + +static struct counter_count_ext ti_eqep_position_ext[] = { + { + .name = "ceiling", + .read = ti_eqep_position_ceiling_read, + .write = ti_eqep_position_ceiling_write, + }, + { + .name = "floor", + .read = ti_eqep_position_floor_read, + .write = ti_eqep_position_floor_write, + }, + { + .name = "enable", + .read = ti_eqep_position_enable_read, + .write = ti_eqep_position_enable_write, + }, +}; + +static struct counter_signal ti_eqep_signals[] = { + [TI_EQEP_SIGNAL_QEPA] = { + .id = TI_EQEP_SIGNAL_QEPA, + .name = "QEPA" + }, + [TI_EQEP_SIGNAL_QEPB] = { + .id = TI_EQEP_SIGNAL_QEPB, + .name = "QEPB" + }, +}; + +static const enum counter_count_function ti_eqep_position_functions[] = { + [TI_EQEP_COUNT_FUNC_QUAD_COUNT] = COUNTER_COUNT_FUNCTION_QUADRATURE_X4, + [TI_EQEP_COUNT_FUNC_DIR_COUNT] = COUNTER_COUNT_FUNCTION_PULSE_DIRECTION, + [TI_EQEP_COUNT_FUNC_UP_COUNT] = COUNTER_COUNT_FUNCTION_INCREASE, + [TI_EQEP_COUNT_FUNC_DOWN_COUNT] = COUNTER_COUNT_FUNCTION_DECREASE, +}; + +static const enum counter_synapse_action ti_eqep_position_synapse_actions[] = { + [TI_EQEP_SYNAPSE_ACTION_BOTH_EDGES] = COUNTER_SYNAPSE_ACTION_BOTH_EDGES, + [TI_EQEP_SYNAPSE_ACTION_RISING_EDGE] = COUNTER_SYNAPSE_ACTION_RISING_EDGE, + [TI_EQEP_SYNAPSE_ACTION_NONE] = COUNTER_SYNAPSE_ACTION_NONE, +}; + +static struct counter_synapse ti_eqep_position_synapses[] = { + { + .actions_list = ti_eqep_position_synapse_actions, + .num_actions = ARRAY_SIZE(ti_eqep_position_synapse_actions), + .signal = &ti_eqep_signals[TI_EQEP_SIGNAL_QEPA], + }, + { + .actions_list = ti_eqep_position_synapse_actions, + .num_actions = ARRAY_SIZE(ti_eqep_position_synapse_actions), + .signal = &ti_eqep_signals[TI_EQEP_SIGNAL_QEPB], + }, +}; + +static struct counter_count ti_eqep_counts[] = { + { + .id = 0, + .name = "QPOSCNT", + .functions_list = ti_eqep_position_functions, + .num_functions = ARRAY_SIZE(ti_eqep_position_functions), + .synapses = ti_eqep_position_synapses, + .num_synapses = ARRAY_SIZE(ti_eqep_position_synapses), + .ext = ti_eqep_position_ext, + .num_ext = ARRAY_SIZE(ti_eqep_position_ext), + }, +}; + +static const struct regmap_config ti_eqep_regmap32_config = { + .name = "32-bit", + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = 0x24, +}; + +static const struct regmap_config ti_eqep_regmap16_config = { + .name = "16-bit", + .reg_bits = 16, + .val_bits = 16, + .reg_stride = 2, + .max_register = 0x1e, +}; + +static int ti_eqep_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ti_eqep_cnt *priv; + void __iomem *base; + int err; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) + return PTR_ERR(base); + + priv->regmap32 = devm_regmap_init_mmio(dev, base, + &ti_eqep_regmap32_config); + if (IS_ERR(priv->regmap32)) + return PTR_ERR(priv->regmap32); + + priv->regmap16 = devm_regmap_init_mmio(dev, base + 0x24, + &ti_eqep_regmap16_config); + if (IS_ERR(priv->regmap16)) + return PTR_ERR(priv->regmap16); + + priv->counter.name = dev_name(dev); + priv->counter.parent = dev; + priv->counter.ops = &ti_eqep_counter_ops; + priv->counter.counts = ti_eqep_counts; + priv->counter.num_counts = ARRAY_SIZE(ti_eqep_counts); + priv->counter.signals = ti_eqep_signals; + priv->counter.num_signals = ARRAY_SIZE(ti_eqep_signals); + priv->counter.priv = priv; + + platform_set_drvdata(pdev, priv); + + /* + * Need to make sure power is turned on. On AM33xx, this comes from the + * parent PWMSS bus driver. On AM17xx, this comes from the PSC power + * domain. + */ + pm_runtime_enable(dev); + pm_runtime_get_sync(dev); + + err = counter_register(&priv->counter); + if (err < 0) { + pm_runtime_put_sync(dev); + pm_runtime_disable(dev); + return err; + } + + return 0; +} + +static int ti_eqep_remove(struct platform_device *pdev) +{ + struct ti_eqep_cnt *priv = platform_get_drvdata(pdev); + struct device *dev = &pdev->dev; + + counter_unregister(&priv->counter); + pm_runtime_put_sync(dev), + pm_runtime_disable(dev); + + return 0; +} + +static const struct of_device_id ti_eqep_of_match[] = { + { .compatible = "ti,am3352-eqep", }, + { }, +}; +MODULE_DEVICE_TABLE(of, ti_eqep_of_match); + +static struct platform_driver ti_eqep_driver = { + .probe = ti_eqep_probe, + .remove = ti_eqep_remove, + .driver = { + .name = "ti-eqep-cnt", + .of_match_table = ti_eqep_of_match, + }, +}; +module_platform_driver(ti_eqep_driver); + +MODULE_AUTHOR("David Lechner "); +MODULE_DESCRIPTION("TI eQEP counter driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index f926342..7f0fa36 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -69,6 +69,20 @@ config GPIO_SYSFS ioctl() operations instead. The character device is always available. +config GPIO_OF_HELPER + bool "GPIO OF helper device (EXPERIMENTAL)" + depends on OF_GPIO + help + Say Y here to add an GPIO OF helper driver + + Allows you specify a GPIO helper based on OF + which allows simple export of GPIO functionality + in user-space. + + Features include, value set/get, direction control, + interrupt/value change poll support, event counting + and others. + config GPIO_GENERIC depends on HAS_IOMEM # Only for IOMEM drivers tristate diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index d2fd19c..6638fc2 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_GPIOLIB) += gpiolib-devprop.o obj-$(CONFIG_OF_GPIO) += gpiolib-of.o obj-$(CONFIG_GPIO_SYSFS) += gpiolib-sysfs.o obj-$(CONFIG_GPIO_ACPI) += gpiolib-acpi.o +obj-$(CONFIG_GPIO_OF_HELPER) += gpio-of-helper.o # Device drivers. Generally keep list sorted alphabetically obj-$(CONFIG_GPIO_GENERIC) += gpio-generic.o diff --git b/drivers/gpio/gpio-of-helper.c b/drivers/gpio/gpio-of-helper.c new file mode 100644 index 0000000..83f362f --- /dev/null +++ b/drivers/gpio/gpio-of-helper.c @@ -0,0 +1,435 @@ +/* + * GPIO OF based helper + * + * A simple DT based driver to provide access to GPIO functionality + * to user-space via sysfs. + * + * Copyright (C) 2013 Pantelis Antoniou + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* fwd decl. */ +struct gpio_of_helper_info; + +enum gpio_type { + GPIO_TYPE_INPUT = 0, + GPIO_TYPE_OUTPUT = 1, +}; + +struct gpio_of_entry { + int id; + struct gpio_of_helper_info *info; + struct device_node *node; + enum gpio_type type; + int gpio; + int irq; + const char *name; + atomic64_t counter; + unsigned int count_flags; +#define COUNT_RISING_EDGE (1 << 0) +#define COUNT_FALLING_EDGE (1 << 1) +}; + +struct gpio_of_helper_info { + struct platform_device *pdev; + struct idr idr; +}; + +static const struct of_device_id gpio_of_helper_of_match[] = { + { + .compatible = "gpio-of-helper", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, gpio_of_helper_of_match); + +static ssize_t gpio_of_helper_show_status(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + char *p, *e; + int id, n; + + p = buf; + e = p + PAGE_SIZE; + n = 0; + idr_for_each_entry(&info->idr, entry, id) { + switch (entry->type) { + case GPIO_TYPE_INPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s %llu\n", + entry->id, entry->name, entry->gpio, "IN", + (unsigned long long) + atomic64_read(&entry->counter)); + break; + case GPIO_TYPE_OUTPUT: + n = snprintf(p, e - p, "%2d %-24s %3d %-3s\n", + entry->id, entry->name, entry->gpio, "OUT"); + break; + } + p += n; + } + + return p - buf; +} + +static DEVICE_ATTR(status, S_IRUGO, + gpio_of_helper_show_status, NULL); + +static irqreturn_t gpio_of_helper_handler(int irq, void *ptr) +{ + struct gpio_of_entry *entry = ptr; + + /* caution - low speed interfaces only! */ + atomic64_inc(&entry->counter); + + return IRQ_HANDLED; +} + +static struct gpio_of_entry * +gpio_of_entry_create(struct gpio_of_helper_info *info, + struct device_node *node) +{ + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + struct gpio_of_entry *entry; + int err, gpio, irq; + unsigned int req_flags, count_flags, irq_flags; + enum gpio_type type; + enum of_gpio_flags gpio_flags; + const char *name; + + /* get the type of the node first */ + if (of_property_read_bool(node, "input")) + type = GPIO_TYPE_INPUT; + else if (of_property_read_bool(node, "output") + || of_property_read_bool(node, "init-low") + || of_property_read_bool(node, "init-high")) + type = GPIO_TYPE_OUTPUT; + else { + dev_err(dev, "Not valid gpio node type\n"); + err = -EINVAL; + goto err_bad_node; + } + + /* get the name */ + if (of_property_read_string(node, "line-name", &name)) + if (of_property_read_string(node, "gpio-name", &name)) + name = node->name; + + err = of_get_named_gpio_flags(node, "gpio", 0, &gpio_flags); + if (IS_ERR_VALUE(err)) { + dev_err(dev, "Failed to get gpio property of '%s'\n", name); + goto err_bad_node; + } + gpio = err; + + req_flags = 0; + count_flags = 0; + + /* set the request flags */ + switch (type) { + case GPIO_TYPE_INPUT: + req_flags = GPIOF_DIR_IN | GPIOF_EXPORT; + if (of_property_read_bool(node, "count-falling-edge")) + count_flags |= COUNT_FALLING_EDGE; + if (of_property_read_bool(node, "count-rising-edge")) + count_flags |= COUNT_RISING_EDGE; + break; + case GPIO_TYPE_OUTPUT: + req_flags = GPIOF_DIR_OUT | GPIOF_EXPORT; + if (of_property_read_bool(node, "init-high")) + req_flags |= GPIOF_OUT_INIT_HIGH; + else if (of_property_read_bool(node, "init-low")) + req_flags |= GPIOF_OUT_INIT_LOW; + break; + } + if (of_property_read_bool(node, "dir-changeable")) + req_flags |= GPIOF_EXPORT_CHANGEABLE; + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_ACTIVE_LOW; + if (gpio_flags & OF_GPIO_SINGLE_ENDED) { + if (gpio_flags & OF_GPIO_ACTIVE_LOW) + req_flags |= GPIOF_OPEN_DRAIN; + else + req_flags |= GPIOF_OPEN_SOURCE; + } + + /* request the gpio */ + err = devm_gpio_request_one(dev, gpio, req_flags, name); + if (err != 0) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + irq = -1; + irq_flags = 0; + + /* counter mode requested - need an interrupt */ + if (count_flags != 0) { + irq = gpio_to_irq(gpio); + if (IS_ERR_VALUE(irq)) { + dev_err(dev, "Failed to request gpio '%s'\n", name); + goto err_bad_node; + } + + if (count_flags & COUNT_RISING_EDGE) + irq_flags |= IRQF_TRIGGER_RISING; + if (count_flags & COUNT_FALLING_EDGE) + irq_flags |= IRQF_TRIGGER_FALLING; + } + +// if (!idr_pre_get(&info->idr, GFP_KERNEL)) { +// dev_err(dev, "Failed on idr_pre_get of '%s'\n", name); +// err = -ENOMEM; +// goto err_no_mem; +// } + + idr_preload(GFP_KERNEL); + + entry = devm_kzalloc(dev, sizeof(*entry), GFP_KERNEL); + if (entry == NULL) { + dev_err(dev, "Failed to allocate gpio entry of '%s'\n", name); + err = -ENOMEM; + goto err_no_mem; + } + + entry->id = -1; + entry->info = info; + entry->node = of_node_get(node); /* get node reference */ + entry->type = type; + entry->gpio = gpio; + entry->irq = irq; + entry->name = name; + + /* interrupt enable is last thing done */ + if (irq >= 0) { + atomic64_set(&entry->counter, 0); + entry->count_flags = count_flags; + err = devm_request_irq(dev, irq, gpio_of_helper_handler, + irq_flags, name, entry); + if (err != 0) { + dev_err(dev, "Failed to request irq of '%s'\n", name); + goto err_no_irq; + } + } + + /* all done; insert */ +// err = idr_get_new(&info->idr, entry, &entry->id); +// if (IS_ERR_VALUE(err)) { +// dev_err(dev, "Failed to idr_get_new of '%s'\n", name); +// goto err_fail_idr; +// } + + err = idr_alloc(&info->idr, entry, 0, 0, GFP_NOWAIT); + if (err >= 0) + entry->id = err; + + idr_preload_end(); + + if (err < 0) { + dev_err(dev, "Failed to idr_get_new of '%s'\n", name); + goto err_fail_idr; + } + + dev_dbg(dev, "Allocated GPIO id=%d name='%s'\n", entry->id, name); + + return entry; + +err_fail_idr: + /* nothing to do */ +err_no_irq: + /* release node ref */ + of_node_put(node); + /* nothing else needs to be done, devres handles it */ +err_no_mem: +err_bad_node: + return ERR_PTR(err); +} + +static int gpio_of_entry_destroy(struct gpio_of_entry *entry) +{ + struct gpio_of_helper_info *info = entry->info; + struct platform_device *pdev = info->pdev; + struct device *dev = &pdev->dev; + + dev_dbg(dev, "Destroying GPIO id=%d\n", entry->id); + + /* remove from the IDR */ + idr_remove(&info->idr, entry->id); + + /* remove node ref */ + of_node_put(entry->node); + + /* free gpio */ + devm_gpio_free(dev, entry->gpio); + + /* gree irq */ + if (entry->irq >= 0) + devm_free_irq(dev, entry->irq, entry); + + /* and free */ + devm_kfree(dev, entry); + + return 0; +} + +static int gpio_of_helper_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct gpio_of_helper_info *info; + struct gpio_of_entry *entry; + struct device_node *pnode = pdev->dev.of_node; + struct device_node *cnode; + struct pinctrl *pinctrl; + int err; + + /* we only support OF */ + if (pnode == NULL) { + dev_err(&pdev->dev, "No platform of_node!\n"); + return -ENODEV; + } + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + /* special handling for probe defer */ + if (PTR_ERR(pinctrl) == -EPROBE_DEFER) + return -EPROBE_DEFER; + + dev_warn(&pdev->dev, + "pins are not configured from the driver\n"); + } + + info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); + if (info == NULL) { + dev_err(&pdev->dev, "Failed to allocate info\n"); + err = -ENOMEM; + goto err_no_mem; + } + platform_set_drvdata(pdev, info); + info->pdev = pdev; + + idr_init(&info->idr); + + err = device_create_file(dev, &dev_attr_status); + if (err != 0) { + dev_err(dev, "Failed to create status sysfs attribute\n"); + goto err_no_sysfs; + } + + for_each_child_of_node(pnode, cnode) { + + entry = gpio_of_entry_create(info, cnode); + if (IS_ERR_OR_NULL(entry)) { + dev_err(dev, "Failed to create gpio entry\n"); + err = PTR_ERR(entry); + goto err_fail_entry; + } + } + + dev_info(&pdev->dev, "ready\n"); + + return 0; +err_fail_entry: + device_remove_file(&pdev->dev, &dev_attr_status); +err_no_sysfs: +err_no_mem: + return err; +} + +static int gpio_of_helper_remove(struct platform_device *pdev) +{ + struct gpio_of_helper_info *info = platform_get_drvdata(pdev); + struct gpio_of_entry *entry; + int id; + + dev_info(&pdev->dev, "removing\n"); + + device_remove_file(&pdev->dev, &dev_attr_status); + + id = 0; + idr_for_each_entry(&info->idr, entry, id) { + /* destroy each and every one */ + gpio_of_entry_destroy(entry); + } + + return 0; +} + +#ifdef CONFIG_PM +//#ifdef CONFIG_PM_RUNTIME +static int gpio_of_helper_runtime_suspend(struct device *dev) +{ + /* place holder */ + return 0; +} + +static int gpio_of_helper_runtime_resume(struct device *dev) +{ + /* place holder */ + return 0; +} +//#endif /* CONFIG_PM_RUNTIME */ + +static struct dev_pm_ops gpio_of_helper_pm_ops = { + SET_RUNTIME_PM_OPS(gpio_of_helper_runtime_suspend, + gpio_of_helper_runtime_resume, NULL) +}; +#define GPIO_OF_HELPER_PM_OPS (&gpio_of_helper_pm_ops) +#else +#define GPIO_OF_HELPER_PM_OPS NULL +#endif /* CONFIG_PM */ + +struct platform_driver gpio_of_helper_driver = { + .probe = gpio_of_helper_probe, + .remove = gpio_of_helper_remove, + .driver = { + .name = "gpio-of-helper", + .owner = THIS_MODULE, + .pm = GPIO_OF_HELPER_PM_OPS, + .of_match_table = gpio_of_helper_of_match, + }, +}; + +module_platform_driver(gpio_of_helper_driver); + +MODULE_AUTHOR("Pantelis Antoniou "); +MODULE_DESCRIPTION("GPIO OF Helper driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:gpio-of-helper"); diff --git a/drivers/gpio/gpiolib-sysfs.c b/drivers/gpio/gpiolib-sysfs.c index fbf6b1a..ec7aa6f 100644 --- a/drivers/gpio/gpiolib-sysfs.c +++ b/drivers/gpio/gpiolib-sysfs.c @@ -37,10 +37,10 @@ static DEFINE_MUTEX(sysfs_lock); /* * /sys/class/gpio/gpioN... only for GPIOs that are exported * /direction - * * MAY BE OMITTED if kernel won't allow direction changes * * is read/write as "in" or "out" * * may also be written as "high" or "low", initializing * output value as specified ("out" implies "low") + * * read-only if kernel won't allow direction changes * /value * * always readable, subject to hardware behavior * * may be writable, as zero/nonzero @@ -53,6 +53,8 @@ static DEFINE_MUTEX(sysfs_lock); * * is read/write as zero/nonzero * * also affects existing and subsequent "falling" and "rising" * /edge configuration + * /label + * * descriptor label */ static ssize_t direction_show(struct device *dev, @@ -83,7 +85,9 @@ static ssize_t direction_store(struct device *dev, mutex_lock(&data->mutex); - if (sysfs_streq(buf, "high")) + if (!data->direction_can_change) + status = -EPERM; + else if (sysfs_streq(buf, "high")) status = gpiod_direction_output_raw(desc, 1); else if (sysfs_streq(buf, "out") || sysfs_streq(buf, "low")) status = gpiod_direction_output_raw(desc, 0); @@ -362,6 +366,23 @@ static ssize_t active_low_store(struct device *dev, } static DEVICE_ATTR_RW(active_low); +static ssize_t label_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; + ssize_t status; + + mutex_lock(&data->mutex); + + status = sprintf(buf, "%s\n", desc->label); + + mutex_unlock(&data->mutex); + + return status; +} +static DEVICE_ATTR_RO(label); + static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, int n) { @@ -373,12 +394,15 @@ static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, if (attr == &dev_attr_direction.attr) { if (!show_direction) - mode = 0; + mode &= 0444; } else if (attr == &dev_attr_edge.attr) { if (gpiod_to_irq(desc) < 0) mode = 0; if (!show_direction && test_bit(FLAG_IS_OUT, &desc->flags)) mode = 0; + } else if (attr == &dev_attr_value.attr) { + if (!show_direction && !test_bit(FLAG_IS_OUT, &desc->flags)) + mode &= 0444; } return mode; @@ -389,6 +413,7 @@ static struct attribute *gpio_attrs[] = { &dev_attr_edge.attr, &dev_attr_value.attr, &dev_attr_active_low.attr, + &dev_attr_label.attr, NULL, }; @@ -402,6 +427,10 @@ static const struct attribute_group *gpio_groups[] = { NULL }; +/* bwlegh, a second device in the same file... get out of my namespace! */ +#define dev_attr_label dev_attr_chip_label +#define label_show chip_label_show + /* * /sys/class/gpio/gpiochipN/ * /base ... matching gpio_chip.base (N) diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c index abdf448..87ea68f 100644 --- a/drivers/gpio/gpiolib.c +++ b/drivers/gpio/gpiolib.c @@ -2687,10 +2687,10 @@ static int gpiod_request_commit(struct gpio_desc *desc, const char *label) if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) { desc_set_label(desc, label ? : "?"); ret = 0; - } else { - kfree_const(label); - ret = -EBUSY; - goto done; +// } else { +// kfree_const(label); +// ret = -EBUSY; +// goto done; } if (chip->request) { diff --git a/drivers/greybus/Kconfig b/drivers/greybus/Kconfig index b84fcaf..78ba3c3 100644 --- a/drivers/greybus/Kconfig +++ b/drivers/greybus/Kconfig @@ -2,8 +2,8 @@ menuconfig GREYBUS tristate "Greybus support" depends on SYSFS - ---help--- - This option enables the Greybus driver core. Greybus is an + help + This option enables the Greybus driver core. Greybus is a hardware protocol that was designed to provide Unipro with a sane application layer. It was originally designed for the ARA project, a module phone system, but has shown up in other @@ -12,7 +12,7 @@ menuconfig GREYBUS Say Y here to enable support for these types of drivers. - To compile this code as a module, chose M here: the module + To compile this code as a module, choose M here: the module will be called greybus.ko if GREYBUS @@ -20,12 +20,12 @@ if GREYBUS config GREYBUS_ES2 tristate "Greybus ES3 USB host controller" depends on USB - ---help--- + help Select this option if you have a Toshiba ES3 USB device that acts as a Greybus "host controller". This device is a bridge from a USB device to a Unipro network. - To compile this code as a module, chose M here: the module + To compile this code as a module, choose M here: the module will be called gb-es2.ko endif # GREYBUS diff --git a/drivers/greybus/arpc.h b/drivers/greybus/arpc.h index c8b83c5..b9ea81b 100644 --- a/drivers/greybus/arpc.h +++ b/drivers/greybus/arpc.h @@ -21,7 +21,7 @@ struct arpc_request_message { __le16 id; /* RPC unique id */ __le16 size; /* Size in bytes of header + payload */ __u8 type; /* RPC type */ - __u8 data[0]; /* ARPC data */ + __u8 data[]; /* ARPC data */ } __packed; struct arpc_response_message { diff --git a/drivers/greybus/connection.c b/drivers/greybus/connection.c index fc8f57f..e3799a5 100644 --- a/drivers/greybus/connection.c +++ b/drivers/greybus/connection.c @@ -361,9 +361,6 @@ static int gb_connection_hd_cport_quiesce(struct gb_connection *connection) if (connection->mode_switch) peer_space += sizeof(struct gb_operation_msg_hdr); - if (!hd->driver->cport_quiesce) - return 0; - ret = hd->driver->cport_quiesce(hd, connection->hd_cport_id, peer_space, GB_CONNECTION_CPORT_QUIESCE_TIMEOUT); diff --git a/drivers/input/misc/tps65218-pwrbutton.c b/drivers/input/misc/tps65218-pwrbutton.c index f011447..e0c6dea 100644 --- a/drivers/input/misc/tps65218-pwrbutton.c +++ b/drivers/input/misc/tps65218-pwrbutton.c @@ -36,7 +36,7 @@ struct tps6521x_data { static const struct tps6521x_data tps65217_data = { .reg_status = TPS65217_REG_STATUS, .pb_mask = TPS65217_STATUS_PB, - .name = "tps65217_pwrbutton", + .name = "tps65217_pwr_but", }; static const struct tps6521x_data tps65218_data = { diff --git a/drivers/input/touchscreen/ar1021_i2c.c b/drivers/input/touchscreen/ar1021_i2c.c index 28644f3..230d27c 100644 --- a/drivers/input/touchscreen/ar1021_i2c.c +++ b/drivers/input/touchscreen/ar1021_i2c.c @@ -17,6 +17,11 @@ #define AR1021_MAX_X 4095 #define AR1021_MAX_Y 4095 +#define AR1021_MAX_PRESSURE 255 + +#define AR1021_CMD 0x55 + +#define AR1021_CMD_ENABLE_TOUCH 0x12 #define AR1021_CMD 0x55 @@ -26,8 +31,29 @@ struct ar1021_i2c { struct i2c_client *client; struct input_dev *input; u8 data[AR1021_TOCUH_PKG_SIZE]; + bool invert_x; + bool invert_y; + bool swap_xy; }; +static bool ar1021_get_prop_u32(struct device *dev, + const char *property, + unsigned int default_value, + unsigned int *value) +{ + u32 val; + int error; + + error = device_property_read_u32(dev, property, &val); + if (error) { + *value = default_value; + return false; + } + + *value = val; + return true; +} + static irqreturn_t ar1021_i2c_irq(int irq, void *dev_id) { struct ar1021_i2c *ar1021 = dev_id; @@ -49,9 +75,22 @@ static irqreturn_t ar1021_i2c_irq(int irq, void *dev_id) x = ((data[2] & 0x1f) << 7) | (data[1] & 0x7f); y = ((data[4] & 0x1f) << 7) | (data[3] & 0x7f); - input_report_abs(input, ABS_X, x); - input_report_abs(input, ABS_Y, y); + if (ar1021->invert_x) + x = AR1021_MAX_X - x; + + if (ar1021->invert_y) + y = AR1021_MAX_Y - y; + + if (ar1021->swap_xy) { + input_report_abs(input, ABS_X, y); + input_report_abs(input, ABS_Y, x); + } else { + input_report_abs(input, ABS_X, x); + input_report_abs(input, ABS_Y, y); + } + input_report_key(input, BTN_TOUCH, button); + input_report_abs(input, ABS_PRESSURE, AR1021_MAX_PRESSURE); input_sync(input); out: @@ -93,6 +132,8 @@ static int ar1021_i2c_probe(struct i2c_client *client, struct ar1021_i2c *ar1021; struct input_dev *input; int error; + unsigned int offset_x, offset_y; + bool data_present; if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { dev_err(&client->dev, "i2c_check_functionality error\n"); @@ -116,10 +157,44 @@ static int ar1021_i2c_probe(struct i2c_client *client, input->open = ar1021_i2c_open; input->close = ar1021_i2c_close; + ar1021->invert_x = device_property_read_bool(&client->dev, "touchscreen-inverted-x"); + ar1021->invert_y = device_property_read_bool(&client->dev, "touchscreen-inverted-y"); + ar1021->swap_xy = device_property_read_bool(&client->dev, "touchscreen-swapped-x-y"); + + data_present = ar1021_get_prop_u32(&client->dev, + "touchscreen-offset-x", + 0, + &offset_x); + + if (data_present) + dev_info(&client->dev, "touchscreen-offset-x: %d\n", offset_x); + + data_present = ar1021_get_prop_u32(&client->dev, + "touchscreen-offset-y", + 0, + &offset_y); + + if (data_present) + dev_info(&client->dev, "touchscreen-offset-y: %d\n", offset_y); + __set_bit(INPUT_PROP_DIRECT, input->propbit); - input_set_capability(input, EV_KEY, BTN_TOUCH); - input_set_abs_params(input, ABS_X, 0, AR1021_MAX_X, 0, 0); - input_set_abs_params(input, ABS_Y, 0, AR1021_MAX_Y, 0, 0); + //input_set_capability(input, EV_KEY, BTN_TOUCH); + + input->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); + input->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH); + + if(ar1021->swap_xy) + { + input_set_abs_params(input, ABS_X, 0, AR1021_MAX_Y, 0, 0); + input_set_abs_params(input, ABS_Y, 0, AR1021_MAX_X, 0, 0); + } + else + { + input_set_abs_params(input, ABS_X, offset_x, AR1021_MAX_X-offset_x, 0, 0); + input_set_abs_params(input, ABS_Y, offset_y, AR1021_MAX_Y-offset_y, 0, 0); + } + + input_set_abs_params(input, ABS_PRESSURE, 0, AR1021_MAX_PRESSURE, 0, 0); input_set_drvdata(input, ar1021); diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c index 83e6855..dd358bf 100644 --- a/drivers/input/touchscreen/ti_am335x_tsc.c +++ b/drivers/input/touchscreen/ti_am335x_tsc.c @@ -34,6 +34,7 @@ #define ADCFSM_STEPID 0x10 #define SEQ_SETTLE 275 #define MAX_12BIT ((1 << 12) - 1) +#define PRESSURE_MAX 1000 #define TSC_IRQENB_MASK (IRQENB_FIFO0THRES | IRQENB_EOS | IRQENB_HW_PEN) @@ -234,6 +235,7 @@ static void titsc_read_coordinates(struct titsc *ts_dev, for (i = 0; i < creads; i++) { xvals[i] = titsc_readl(ts_dev, REG_FIFO0); xvals[i] &= 0xfff; + pr_debug("i %d xval %d yval %d z1 %d z2 %d\n", i, xvals[i], yvals[i], *z1, *z2); } /* @@ -312,13 +314,13 @@ static irqreturn_t titsc_irq(int irq, void *dev) * Resistance(touch) = x plate resistance * * x postion/4096 * ((z2 / z1) - 1) */ - z = z1 - z2; + z = z2 - z1; z *= x; z *= ts_dev->x_plate_resistance; - z /= z2; + z /= z1; z = (z + 2047) >> 12; - - if (z <= MAX_12BIT) { + pr_debug("x %d y %d z1 %d z2 %d z %d\n", x, y, z1, z2, z); + if (z <= PRESSURE_MAX) { input_report_abs(input_dev, ABS_X, x); input_report_abs(input_dev, ABS_Y, y); input_report_abs(input_dev, ABS_PRESSURE, z); @@ -459,6 +461,7 @@ static int titsc_probe(struct platform_device *pdev) input_dev->name = "ti-tsc"; input_dev->dev.parent = &pdev->dev; + __set_bit(INPUT_PROP_DIRECT, input_dev->propbit); input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS); input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH); diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index c55b637..c39f5b1 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -466,6 +466,13 @@ config PVPANIC a paravirtualized device provided by QEMU; it lets a virtual machine (guest) communicate panic events to the host. +config UDOO_ARD + tristate "UDOO-Arduino erase/reset Driver" + default y + help + This driver is used to erase and reset arduino board via command sent + over USB-to-SERIAL connection. + source "drivers/misc/c2port/Kconfig" source "drivers/misc/eeprom/Kconfig" source "drivers/misc/cb710/Kconfig" @@ -476,6 +483,7 @@ source "drivers/misc/mei/Kconfig" source "drivers/misc/vmw_vmci/Kconfig" source "drivers/misc/mic/Kconfig" source "drivers/misc/genwqe/Kconfig" +source "drivers/misc/cape/Kconfig" source "drivers/misc/echo/Kconfig" source "drivers/misc/cxl/Kconfig" source "drivers/misc/ocxl/Kconfig" diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile index c1860d3..fd9d547 100644 --- a/drivers/misc/Makefile +++ b/drivers/misc/Makefile @@ -48,9 +48,11 @@ obj-$(CONFIG_SRAM) += sram.o obj-$(CONFIG_SRAM_EXEC) += sram-exec.o obj-y += mic/ obj-$(CONFIG_GENWQE) += genwqe/ +obj-y += cape/ obj-$(CONFIG_ECHO) += echo/ obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o obj-$(CONFIG_CXL_BASE) += cxl/ +obj-$(CONFIG_UDOO_ARD) += udoo_ard.o obj-$(CONFIG_PCI_ENDPOINT_TEST) += pci_endpoint_test.o obj-$(CONFIG_OCXL) += ocxl/ obj-y += cardreader/ diff --git b/drivers/misc/cape/Kconfig b/drivers/misc/cape/Kconfig new file mode 100644 index 0000000..a2ef85e --- /dev/null +++ b/drivers/misc/cape/Kconfig @@ -0,0 +1,5 @@ +# +# Capes +# + +source "drivers/misc/cape/beaglebone/Kconfig" diff --git b/drivers/misc/cape/Makefile b/drivers/misc/cape/Makefile new file mode 100644 index 0000000..7c4eb96 --- /dev/null +++ b/drivers/misc/cape/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for cape like devices +# + +obj-y += beaglebone/ diff --git b/drivers/misc/cape/beaglebone/Kconfig b/drivers/misc/cape/beaglebone/Kconfig new file mode 100644 index 0000000..eeb6782 --- /dev/null +++ b/drivers/misc/cape/beaglebone/Kconfig @@ -0,0 +1,10 @@ +# +# Beaglebone capes +# + +config BEAGLEBONE_PINMUX_HELPER + tristate "Beaglebone Pinmux Helper" + depends on ARCH_OMAP2PLUS && OF + default n + help + Say Y here to include support for the pinmux helper diff --git b/drivers/misc/cape/beaglebone/Makefile b/drivers/misc/cape/beaglebone/Makefile new file mode 100644 index 0000000..7f4617a --- /dev/null +++ b/drivers/misc/cape/beaglebone/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for beaglebone capes +# + +obj-$(CONFIG_BEAGLEBONE_PINMUX_HELPER) += bone-pinmux-helper.o diff --git b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c new file mode 100644 index 0000000..d81363a --- /dev/null +++ b/drivers/misc/cape/beaglebone/bone-pinmux-helper.c @@ -0,0 +1,242 @@ +/* + * Pinmux helper driver + * + * Copyright (C) 2013 Pantelis Antoniou + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +static const struct of_device_id bone_pinmux_helper_of_match[] = { + { + .compatible = "bone-pinmux-helper", + }, + { }, +}; +MODULE_DEVICE_TABLE(of, bone_pinmux_helper_of_match); + +struct pinmux_helper_data { + struct pinctrl *pinctrl; + char *selected_state_name; +}; + +static ssize_t pinmux_helper_show_state(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct platform_device *pdev = to_platform_device(dev); + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + const char *name; + + name = data->selected_state_name; + if (name == NULL || strlen(name) == 0) + name = "none"; + return sprintf(buf, "%s\n", name); +} + +static ssize_t pinmux_helper_store_state(struct device *dev, + struct device_attribute *attr, const char *buf, size_t count) +{ + struct platform_device *pdev = to_platform_device(dev); + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + struct pinctrl_state *state; + char *state_name; + char *s; + int err; + + /* duplicate (as a null terminated string) */ + state_name = kmalloc(count + 1, GFP_KERNEL); + if (state_name == NULL) + return -ENOMEM; + memcpy(state_name, buf, count); + state_name[count] = '\0'; + + /* and chop off newline */ + s = strchr(state_name, '\n'); + if (s != NULL) + *s = '\0'; + + /* try to select default state at first (if it exists) */ + state = pinctrl_lookup_state(data->pinctrl, state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) + dev_err(dev, "Failed to select state %s\n", + state_name); + } else { + dev_err(dev, "Failed to find state %s\n", state_name); + err = PTR_RET(state); + } + + if (err == 0) { + kfree(data->selected_state_name); + data->selected_state_name = state_name; + } + + return err ? err : count; +} + +static DEVICE_ATTR(state, S_IWUSR | S_IRUGO, + pinmux_helper_show_state, pinmux_helper_store_state); + +static struct attribute *pinmux_helper_attributes[] = { + &dev_attr_state.attr, + NULL +}; + +static const struct attribute_group pinmux_helper_attr_group = { + .attrs = pinmux_helper_attributes, +}; + +static int bone_pinmux_helper_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct pinmux_helper_data *data; + struct pinctrl_state *state; + char *state_name; + const char *mode_name; + int mode_len; + int err; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (data == NULL) { + dev_err(dev, "Failed to allocate data\n"); + err = -ENOMEM; + goto err_no_mem; + } + + state_name = kmalloc(strlen(PINCTRL_STATE_DEFAULT) + 1, + GFP_KERNEL); + if (state_name == NULL) { + dev_err(dev, "Failed to allocate state name\n"); + err = -ENOMEM; + goto err_no_state_mem; + } + data->selected_state_name = state_name; + strcpy(data->selected_state_name, PINCTRL_STATE_DEFAULT); + + platform_set_drvdata(pdev, data); + + data->pinctrl = devm_pinctrl_get(dev); + if (IS_ERR(data->pinctrl)) { + dev_err(dev, "Failed to get pinctrl\n"); + err = PTR_RET(data->pinctrl); + goto err_no_pinctrl; + } + + /* See if an initial mode is specified in the device tree */ + mode_name = of_get_property(dev->of_node, "mode", &mode_len); + + err = -1; + if (mode_name != NULL ) { + state_name = kmalloc(mode_len + 1, GFP_KERNEL); + if (state_name == NULL) { + dev_err(dev, "Failed to allocate state name\n"); + err = -ENOMEM; + goto err_no_mode_mem; + } + strncpy(state_name, mode_name, mode_len); + + /* try to select requested mode */ + state = pinctrl_lookup_state(data->pinctrl, state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) { + dev_warn(dev, "Unable to select requested mode %s\n", state_name); + kfree(state_name); + } else { + kfree(data->selected_state_name); + data->selected_state_name = state_name; + dev_notice(dev, "Set initial pinmux mode to %s\n", state_name); + } + } + } + + /* try to select default state if mode_name failed */ + if ( err != 0) { + state = pinctrl_lookup_state(data->pinctrl, + data->selected_state_name); + if (!IS_ERR(state)) { + err = pinctrl_select_state(data->pinctrl, state); + if (err != 0) { + dev_err(dev, "Failed to select default state\n"); + goto err_no_state; + } + } else { + data->selected_state_name = '\0'; + } + } + + /* Register sysfs hooks */ + err = sysfs_create_group(&dev->kobj, &pinmux_helper_attr_group); + if (err) { + dev_err(dev, "Failed to create sysfs group\n"); + goto err_no_sysfs; + } + + return 0; + +err_no_sysfs: +err_no_state: +err_no_mode_mem: + devm_pinctrl_put(data->pinctrl); +err_no_pinctrl: + devm_kfree(dev, data->selected_state_name); +err_no_state_mem: + devm_kfree(dev, data); +err_no_mem: + return err; +} + +static int bone_pinmux_helper_remove(struct platform_device *pdev) +{ + struct pinmux_helper_data *data = platform_get_drvdata(pdev); + struct device *dev = &pdev->dev; + + sysfs_remove_group(&dev->kobj, &pinmux_helper_attr_group); + kfree(data->selected_state_name); + devm_pinctrl_put(data->pinctrl); + devm_kfree(dev, data); + + return 0; +} + +struct platform_driver bone_pinmux_helper_driver = { + .probe = bone_pinmux_helper_probe, + .remove = bone_pinmux_helper_remove, + .driver = { + .name = "bone-pinmux-helper", + .owner = THIS_MODULE, + .of_match_table = bone_pinmux_helper_of_match, + }, +}; + +module_platform_driver(bone_pinmux_helper_driver); + +MODULE_AUTHOR("Pantelis Antoniou"); +MODULE_DESCRIPTION("Beaglebone pinmux helper driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:bone-pinmux-helper"); diff --git b/drivers/misc/udoo_ard.c b/drivers/misc/udoo_ard.c new file mode 100755 index 0000000..2210738 --- /dev/null +++ b/drivers/misc/udoo_ard.c @@ -0,0 +1,417 @@ +/* + * udoo_ard.c + * UDOO quad/dual Arduino flash erase / CPU resetter + * + * Copyright (C) 2013-2015 Aidilab srl + * Author: UDOO Team + * Author: Giuseppe Pagano + * Author: Francesco Montefoschi + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see . + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_NAME "udoo_ard" +#define PINCTRL_DEFAULT "default" +#define AUTH_TOKEN 0x5A5A +#define MAX_MSEC_SINCE_LAST_IRQ 400 +#define GRAY_TIME_BETWEEN_RESET 10000 // In this time we can't accept new erase/reset code + +static struct workqueue_struct *erase_reset_wq; +typedef struct { + struct work_struct erase_reset_work; + struct pinctrl *pinctrl; + struct pinctrl_state *pins_default; + int step; + int cmdcode; + int erase_reset_lock; + int gpio_bossac_clk; + int gpio_bossac_dat; + int gpio_ard_erase; + int gpio_ard_reset; + unsigned long last_int_time_in_ns; + unsigned long last_int_time_in_sec; +} erase_reset_work_t; + +erase_reset_work_t *work; +static u32 origTX, origRX; // original UART4 TX/RX pad control registers +static int major; // for /dev/udoo_ard +static struct class *udoo_class; + +static struct platform_device_id udoo_ard_devtype[] = { + { + /* keep it for coldfire */ + .name = DRIVER_NAME, + .driver_data = 0, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(platform, udoo_ard_devtype); + +static const struct of_device_id udoo_ard_dt_ids[] = { + { .compatible = "udoo,imx6q-udoo-ard", .data = &udoo_ard_devtype[0], }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, udoo_ard_dt_ids); + +static void disable_serial(void) +{ + u32 addrTX; + void __iomem *_addrTX; + + printk("[bossac] Disable UART4 serial port.\n"); + + addrTX = 0x20E01F8; + _addrTX = ioremap(addrTX, 8); + + origTX = __raw_readl(_addrTX); + origRX = __raw_readl(_addrTX + 0x4); + + __raw_writel(0x15, _addrTX); + __raw_writel(0x15, _addrTX + 0x4); + + iounmap(_addrTX); +} + +static void enable_serial(void) +{ + u32 addrTX; + void __iomem *_addrTX; + + printk("[bossac] Enable UART4 serial port.\n"); + + addrTX = 0x20E01F8; + _addrTX = ioremap(addrTX, 8); + + __raw_writel(origTX, _addrTX); + __raw_writel(origRX, _addrTX + 0x4); + + iounmap(_addrTX); +} + +static void erase_reset(void) +{ + printk("[bossac] UDOO ERASE and RESET on Sam3x started.\n"); + + gpio_direction_input(work->gpio_ard_erase); + gpio_set_value(work->gpio_ard_reset, 1); + msleep(1); + + gpio_direction_output(work->gpio_ard_erase, 1); + msleep(300); + gpio_direction_input(work->gpio_ard_erase); + + msleep(10); + gpio_set_value(work->gpio_ard_reset, 0); + + msleep(80); + gpio_set_value(work->gpio_ard_reset, 1); + + printk("[bossac] UDOO ERASE and RESET on Sam3x EXECUTED.\n"); +} + +static void shutdown_sam3x(void) +{ + printk("[bossac] RESET on Sam3x.\n"); + + gpio_set_value(work->gpio_ard_reset, 0); +} + +static void erase_reset_wq_function( struct work_struct *work2) +{ + disable_serial(); + erase_reset(); + msleep(GRAY_TIME_BETWEEN_RESET); + + work->erase_reset_lock = 0; +} + +/* + * Called everytime the gpio_bossac_clk signal toggles. + * If the auth token (16 bit) is found, we look for the command code (4 bit). + * The code 0x0F is sent by Bossac to trigger an erase/reset (to achieve this, + * erase_reset_wq is scheduled). Before starting to program the flash, we disable + * the UART4 serial port, otherwise there is too noise on the serial lines (the + * programming port and UART4 port are connected together, see hw schematics). + * When Bossac finishes to flash/verify, the code 0x00 is sent which re-enables + * the UART4 port. + */ +static irqreturn_t udoo_bossac_req(int irq, void *dev_id) +{ + int retval, auth_bit, expected_bit, msec_since_last_irq; + u64 nowsec; + unsigned long rem_nsec; + erase_reset_work_t *erase_reset_work; + + auth_bit = 0; + if (gpio_get_value(work->gpio_bossac_dat) != 0x0) { + auth_bit = 1; + } + + erase_reset_work = (erase_reset_work_t *)work; + + nowsec = local_clock(); + rem_nsec = do_div(nowsec, 1000000000) ; + msec_since_last_irq = (((unsigned long)nowsec * 1000) + rem_nsec/1000000 ) - (((unsigned long)erase_reset_work->last_int_time_in_sec * 1000) + erase_reset_work->last_int_time_in_ns/1000000); + + if (msec_since_last_irq > MAX_MSEC_SINCE_LAST_IRQ) { + erase_reset_work->step = 0; +#ifdef DEBUG + printk("[bossac] Reset authentication timeout!\n"); +#endif + } + +#ifdef DEBUG + printk("[bossac] STEP %d -> 0x%d \n", erase_reset_work->step, auth_bit); +#endif + erase_reset_work->last_int_time_in_ns = rem_nsec; + erase_reset_work->last_int_time_in_sec = nowsec; + + if ( erase_reset_work->step < 16 ) { // Authenticating received token bit. + expected_bit = (( AUTH_TOKEN >> erase_reset_work->step ) & 0x01 ); + if ( auth_bit == expected_bit ) { + erase_reset_work->step = erase_reset_work->step + 1; + } else { + erase_reset_work->step = 0; + } + } else { // Passed all authentication step. Receiving command code. + erase_reset_work->cmdcode = erase_reset_work->cmdcode | (auth_bit << (erase_reset_work->step - 16)); + erase_reset_work->step = erase_reset_work->step + 1; + } + +#ifdef DEBUG + printk("erase_reset_work->erase_reset_lock = %d \n", erase_reset_work->erase_reset_lock); +#endif + if ( erase_reset_work->step == 20 ) { // Passed authentication and code acquiring step. +#ifdef DEBUG + printk("[bossac] Received code = 0x%04x \n", erase_reset_work->cmdcode); +#endif + if (erase_reset_work->cmdcode == 0xF) { + if (erase_reset_work->erase_reset_lock == 0) { + erase_reset_work->erase_reset_lock = 1; + retval = queue_work( erase_reset_wq, (struct work_struct *)work ); + } else { +#ifdef DEBUG + printk("Erase and reset operation already in progress. Do nothing.\n"); +#endif + } + } else { + enable_serial(); + } + erase_reset_work->step = 0; + erase_reset_work->cmdcode = 0; + } + + return IRQ_HANDLED; +} + +/* + * Takes control of clock, data, erase, reset GPIOs. + */ +static int gpio_setup(void) +{ + int ret; + + ret = gpio_request(work->gpio_bossac_clk, "BOSSA_CLK"); + if (ret) { + printk(KERN_ERR "request BOSSA_CLK IRQ\n"); + return -1; + } else { + gpio_direction_input(work->gpio_bossac_clk); + } + + ret = gpio_request(work->gpio_bossac_dat, "BOSSA_DAT"); + if (ret) { + printk(KERN_ERR "request BOSSA_DAT IRQ\n"); + return -1; + } else { + gpio_direction_input(work->gpio_bossac_dat); + } + + ret = gpio_request(work->gpio_ard_erase, "BOSSAC"); + if (ret) { + printk(KERN_ERR "request GPIO FOR ARDUINO ERASE\n"); + return -1; + } else { + gpio_direction_input(work->gpio_ard_erase); + } + + ret = gpio_request(work->gpio_ard_reset, "BOSSAC"); + if (ret) { + printk(KERN_ERR "request GPIO FOR ARDUINO RESET\n"); + return -1; + } else { + gpio_direction_output(work->gpio_ard_reset, 1); + } + + return 0; +} + +static ssize_t device_write(struct file *filp, const char *buff, size_t len, loff_t *off) +{ + char msg[10]; + long res; + + if (len > 10) + return -EINVAL; + + + res = copy_from_user(msg, buff, len); + if (res) { + return -EFAULT; + } + msg[len] = '\0'; + + if (strcmp(msg, "erase")==0) { + erase_reset(); + } else if (strcmp(msg, "shutdown")==0) { + shutdown_sam3x(); + } else if (strcmp(msg, "uartoff")==0) { + disable_serial(); + } else if (strcmp(msg, "uarton")==0) { + enable_serial(); + } else { + printk("[bossac] udoo_ard invalid operation! %s", msg); + } + + return len; +} + +static struct file_operations fops = { + .write = device_write, +}; + +/* + * If a fdt udoo_ard entry is found, we register an IRQ on bossac clock line + * and we create /dev/udoo_ard + */ +static int udoo_ard_probe(struct platform_device *pdev) +{ + int retval; + struct device *temp_class; + struct platform_device *bdev; + struct device_node *np; + + bdev = kzalloc(sizeof(*bdev), GFP_KERNEL); + np = pdev->dev.of_node; + + if (!np) + return -ENODEV; + + work = (erase_reset_work_t *)kmalloc(sizeof(erase_reset_work_t), GFP_KERNEL); + if (work) { + work->gpio_ard_reset = of_get_named_gpio(np, "bossac-reset-gpio", 0); + work->gpio_ard_erase = of_get_named_gpio(np, "bossac-erase-gpio", 0); + work->gpio_bossac_clk = of_get_named_gpio(np, "bossac-clk-gpio", 0); + work->gpio_bossac_dat = of_get_named_gpio(np, "bossac-dat-gpio", 0); + work->pinctrl = devm_pinctrl_get(&pdev->dev); + work->pins_default = pinctrl_lookup_state(work->pinctrl, PINCTRL_DEFAULT); + } else { + printk("[bossac] Failed to allocate data structure."); + return -ENOMEM; + } + + pinctrl_select_state(work->pinctrl, work->pins_default); + gpio_setup(); + + printk("[bossac] Registering IRQ %d for BOSSAC Arduino erase/reset operation\n", gpio_to_irq(work->gpio_bossac_clk)); + retval = request_irq(gpio_to_irq(work->gpio_bossac_clk), udoo_bossac_req, IRQF_TRIGGER_FALLING, "UDOO", bdev); + + major = register_chrdev(major, "udoo_ard", &fops); + if (major < 0) { + printk(KERN_ERR "[bossac] Cannot get major for UDOO Ard\n"); + return -EBUSY; + } + + udoo_class = class_create(THIS_MODULE, "udoo_ard"); + if (IS_ERR(udoo_class)) { + return PTR_ERR(udoo_class); + } + + temp_class = device_create(udoo_class, NULL, MKDEV(major, 0), NULL, "udoo_ard"); + if (IS_ERR(temp_class)) { + return PTR_ERR(temp_class); + } + + printk("[bossac] Created device file /dev/udoo_ard\n"); + + erase_reset_wq = create_workqueue("erase_reset_queue"); + if (erase_reset_wq) { + + /* Queue some work (item 1) */ + if (work) { + INIT_WORK( (struct work_struct *)work, erase_reset_wq_function ); + work->step = 1; + work->cmdcode = 0; + work->last_int_time_in_ns = 0; + work->last_int_time_in_sec = 0; + work->erase_reset_lock = 0; + // retval = queue_work( erase_reset_wq, (struct work_struct *)work ); + } + } + return 0; +} + +static int udoo_ard_remove(struct platform_device *pdev) +{ + printk("[bossac] Unloading UDOO ard driver.\n"); + free_irq(gpio_to_irq(work->gpio_bossac_clk), NULL); + + gpio_free(work->gpio_ard_reset); + gpio_free(work->gpio_ard_erase); + gpio_free(work->gpio_bossac_clk); + gpio_free(work->gpio_bossac_dat); + + device_destroy(udoo_class, MKDEV(major, 0)); + class_destroy(udoo_class); + unregister_chrdev(major, "udoo_ard"); + + return 0; +} + +static struct platform_driver udoo_ard_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .of_match_table = udoo_ard_dt_ids, + }, + .id_table = udoo_ard_devtype, + .probe = udoo_ard_probe, + .remove = udoo_ard_remove, +}; + +module_platform_driver(udoo_ard_driver); + +MODULE_ALIAS("platform:"DRIVER_NAME); +MODULE_LICENSE("GPL"); diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index d0df054..714e238 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -1467,6 +1467,8 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) omap_hsmmc_set_power(host, 0); break; case MMC_POWER_UP: + omap_hsmmc_set_power(host, 0); + msleep(10); omap_hsmmc_set_power(host, 1); break; case MMC_POWER_ON: diff --git a/drivers/net/ethernet/ti/davinci_mdio.c b/drivers/net/ethernet/ti/davinci_mdio.c index 702fdc3..e201a20 100644 --- a/drivers/net/ethernet/ti/davinci_mdio.c +++ b/drivers/net/ethernet/ti/davinci_mdio.c @@ -92,6 +92,10 @@ struct davinci_mdio_data { u32 clk_div; }; +#if IS_ENABLED(CONFIG_OF) +static void davinci_mdio_update_dt_from_phymask(u32 phy_mask); +#endif + static void davinci_mdio_init_clk(struct davinci_mdio_data *data) { u32 mdio_in, div, mdio_out_khz, access_time; @@ -159,6 +163,12 @@ static int davinci_mdio_reset(struct mii_bus *bus) /* restrict mdio bus to live phys only */ dev_info(data->dev, "detected phy mask %x\n", ~phy_mask); phy_mask = ~phy_mask; + + #if IS_ENABLED(CONFIG_OF) + if (of_machine_is_compatible("ti,am335x-bone")) + davinci_mdio_update_dt_from_phymask(phy_mask); + #endif + } else { /* desperately scan all phys */ dev_warn(data->dev, "no live phy, scanning all\n"); @@ -474,6 +484,93 @@ static int davinci_mdio_runtime_resume(struct device *dev) davinci_mdio_enable(data); return 0; } +static void davinci_mdio_update_dt_from_phymask(u32 phy_mask) +{ + int i, len, skip; + u32 addr; + __be32 *old_phy_p, *phy_id_p; + struct property *phy_id_property = NULL; + struct device_node *node_p, *slave_p; + + addr = 0; + + for (i = 0; i < PHY_MAX_ADDR; i++) { + if ((phy_mask & (1 << i)) == 0) { + addr = (u32) i; + break; + } + } + + for_each_compatible_node(node_p, NULL, "ti,cpsw") { + for_each_node_by_name(slave_p, "slave") { + +#if IS_ENABLED(CONFIG_OF_OVERLAY) + skip = 1; + // Hack, the overlay fixup "slave" doesn't have phy-mode... + old_phy_p = (__be32 *) of_get_property(slave_p, "phy-mode", &len); + + if (len != (sizeof(__be32 *) * 1)) + { + skip = 0; + } + + if (skip) { +#endif + + old_phy_p = (__be32 *) of_get_property(slave_p, "phy_id", &len); + + if (len != (sizeof(__be32 *) * 2)) + goto err_out; + + if (old_phy_p) { + + phy_id_property = kzalloc(sizeof(*phy_id_property), GFP_KERNEL); + + if (! phy_id_property) + goto err_out; + + phy_id_property->length = len; + phy_id_property->name = kstrdup("phy_id", GFP_KERNEL); + phy_id_property->value = kzalloc(len, GFP_KERNEL); + + if (! phy_id_property->name) + goto err_out; + + if (! phy_id_property->value) + goto err_out; + + memcpy(phy_id_property->value, old_phy_p, len); + + phy_id_p = (__be32 *) phy_id_property->value + 1; + + *phy_id_p = cpu_to_be32(addr); + + of_update_property(slave_p, phy_id_property); + pr_info("davinci_mdio: dt: updated phy_id[%d] from phy_mask[%x]\n", addr, phy_mask); + + ++addr; + } +#if IS_ENABLED(CONFIG_OF_OVERLAY) + } +#endif + } + } + + return; + +err_out: + + if (phy_id_property) { + if (phy_id_property->name) + kfree(phy_id_property->name); + + if (phy_id_property->value) + kfree(phy_id_property->value); + + if (phy_id_property) + kfree(phy_id_property); + } +} #endif #ifdef CONFIG_PM_SLEEP diff --git a/drivers/net/wireless/broadcom/brcm80211/Kconfig b/drivers/net/wireless/broadcom/brcm80211/Kconfig index a5bf16c..b239e06 100644 --- a/drivers/net/wireless/broadcom/brcm80211/Kconfig +++ b/drivers/net/wireless/broadcom/brcm80211/Kconfig @@ -37,3 +37,14 @@ config BRCMDBG select WANT_DEV_COREDUMP if BRCMFMAC ---help--- Selecting this enables additional code for debug purposes. + +config BRCMFMAC_PCIE_BARWIN_SZ + bool "Custom PCIE BAR window size support for FullMAC driver" + depends on BRCMFMAC + depends on PCI + default n + ---help--- + If you say Y here, the FMAC driver will use custom PCIE BAR + window size. Say Y to allow developers to use custom PCIE + BAR window size when HOST PCIE IP can support less then 4MB + BAR window. diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcdc.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcdc.c index 2c95a08..705130c 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcdc.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcdc.c @@ -87,6 +87,8 @@ struct brcmf_proto_bcdc_header { * plus any space that might be needed * for bus alignment padding. */ +#define ROUND_UP_MARGIN 2048 + struct brcmf_bcdc { u16 reqid; u8 bus_header[BUS_HEADER_LEN]; @@ -471,7 +473,7 @@ int brcmf_proto_bcdc_attach(struct brcmf_pub *drvr) drvr->hdrlen += BCDC_HEADER_LEN + BRCMF_PROT_FW_SIGNAL_MAX_TXBYTES; drvr->bus_if->maxctl = BRCMF_DCMD_MAXLEN + - sizeof(struct brcmf_proto_bcdc_dcmd); + sizeof(struct brcmf_proto_bcdc_dcmd) + ROUND_UP_MARGIN; return 0; fail: diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c index fc12598..87f1155 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bcmsdh.c @@ -36,6 +36,7 @@ #include "sdio.h" #include "core.h" #include "common.h" +#include "cfg80211.h" #define SDIOH_API_ACCESS_RETRY_LIMIT 2 @@ -43,6 +44,8 @@ #define SDIO_FUNC1_BLOCKSIZE 64 #define SDIO_FUNC2_BLOCKSIZE 512 +#define SDIO_4373_FUNC2_BLOCKSIZE 256 +#define SDIO_435X_FUNC2_BLOCKSIZE 256 /* Maximum milliseconds to wait for F2 to come up */ #define SDIO_WAIT_F2RDY 3000 @@ -865,7 +868,7 @@ static void brcmf_sdiod_freezer_detach(struct brcmf_sdio_dev *sdiodev) } #endif /* CONFIG_PM_SLEEP */ -static int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev) +int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev) { sdiodev->state = BRCMF_SDIOD_DOWN; if (sdiodev->bus) { @@ -900,9 +903,10 @@ static void brcmf_sdiod_host_fixup(struct mmc_host *host) host->caps |= MMC_CAP_NONREMOVABLE; } -static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev) +int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev) { int ret = 0; + unsigned int f2_blksz = SDIO_FUNC2_BLOCKSIZE; sdio_claim_host(sdiodev->func1); @@ -912,11 +916,28 @@ static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev) sdio_release_host(sdiodev->func1); goto out; } - ret = sdio_set_block_size(sdiodev->func2, SDIO_FUNC2_BLOCKSIZE); + + switch (sdiodev->func2->device) { + case SDIO_DEVICE_ID_CYPRESS_4373: + f2_blksz = SDIO_4373_FUNC2_BLOCKSIZE; + break; + case SDIO_DEVICE_ID_BROADCOM_4359: + case SDIO_DEVICE_ID_CYPRESS_89359: + case SDIO_DEVICE_ID_BROADCOM_4354: + case SDIO_DEVICE_ID_BROADCOM_4356: + f2_blksz = SDIO_435X_FUNC2_BLOCKSIZE; + break; + default: + break; + } + + ret = sdio_set_block_size(sdiodev->func2, f2_blksz); if (ret) { brcmf_err("Failed to set F2 blocksize\n"); sdio_release_host(sdiodev->func1); goto out; + } else { + brcmf_dbg(SDIO, "set F2 blocksize to %d\n", f2_blksz); } /* increase F2 timeout */ @@ -969,8 +990,10 @@ static const struct sdio_device_id brcmf_sdmmc_ids[] = { BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_43455), BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_4354), BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_4356), + BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_BROADCOM_4359), BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_CYPRESS_4373), BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_CYPRESS_43012), + BRCMF_SDIO_DEVICE(SDIO_DEVICE_ID_CYPRESS_89359), { /* end: all zeroes */ } }; MODULE_DEVICE_TABLE(sdio, brcmf_sdmmc_ids); @@ -1039,6 +1062,7 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func, dev_set_drvdata(&func->dev, bus_if); dev_set_drvdata(&sdiodev->func1->dev, bus_if); sdiodev->dev = &sdiodev->func1->dev; + dev_set_drvdata(&sdiodev->func2->dev, bus_if); brcmf_sdiod_change_state(sdiodev, BRCMF_SDIOD_DOWN); @@ -1055,6 +1079,7 @@ static int brcmf_ops_sdio_probe(struct sdio_func *func, fail: dev_set_drvdata(&func->dev, NULL); dev_set_drvdata(&sdiodev->func1->dev, NULL); + dev_set_drvdata(&sdiodev->func2->dev, NULL); kfree(sdiodev); kfree(bus_if); return err; @@ -1109,14 +1134,26 @@ static int brcmf_ops_sdio_suspend(struct device *dev) struct brcmf_bus *bus_if; struct brcmf_sdio_dev *sdiodev; mmc_pm_flag_t sdio_flags; + struct brcmf_cfg80211_info *config; + int retry = BRCMF_PM_WAIT_MAXRETRY; func = container_of(dev, struct sdio_func, dev); + bus_if = dev_get_drvdata(dev); + config = bus_if->drvr->config; + brcmf_dbg(SDIO, "Enter: F%d\n", func->num); + + while (retry && + config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) { + usleep_range(10000, 20000); + retry--; + } + if (!retry && config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) + brcmf_err("timed out wait for cfg80211 suspended\n"); + if (func->num != 1) return 0; - - bus_if = dev_get_drvdata(dev); sdiodev = bus_if->bus_priv.sdio; brcmf_sdiod_freezer_on(sdiodev); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bus.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bus.h index 623c016..e62c348 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bus.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/bus.h @@ -255,7 +255,7 @@ void brcmf_rx_event(struct device *dev, struct sk_buff *rxp); int brcmf_alloc(struct device *dev, struct brcmf_mp_device *settings); /* Indication from bus module regarding presence/insertion of dongle. */ -int brcmf_attach(struct device *dev); +int brcmf_attach(struct device *dev, bool start_bus); /* Indication from bus module regarding removal/absence of dongle */ void brcmf_detach(struct device *dev); void brcmf_free(struct device *dev); @@ -271,6 +271,7 @@ void brcmf_bus_change_state(struct brcmf_bus *bus, enum brcmf_bus_state state); s32 brcmf_iovar_data_set(struct device *dev, char *name, void *data, u32 len); void brcmf_bus_add_txhdrlen(struct device *dev, uint len); +int brcmf_fwlog_attach(struct device *dev); #ifdef CONFIG_BRCMFMAC_SDIO void brcmf_sdio_exit(void); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c index 4ca5035..256604b 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c @@ -22,6 +22,7 @@ #include "p2p.h" #include "btcoex.h" #include "pno.h" +#include "fwsignal.h" #include "cfg80211.h" #include "feature.h" #include "fwil.h" @@ -54,6 +55,7 @@ #define RSN_AKM_PSK 2 /* Pre-shared Key */ #define RSN_AKM_SHA256_1X 5 /* SHA256, 802.1X */ #define RSN_AKM_SHA256_PSK 6 /* SHA256, Pre-shared Key */ +#define RSN_AKM_SAE 8 /* SAE */ #define RSN_CAP_LEN 2 /* Length of RSN capabilities */ #define RSN_CAP_PTK_REPLAY_CNTR_MASK (BIT(2) | BIT(3)) #define RSN_CAP_MFPR_MASK BIT(6) @@ -82,8 +84,6 @@ #define BRCMF_ND_INFO_TIMEOUT msecs_to_jiffies(2000) -#define BRCMF_PS_MAX_TIMEOUT_MS 2000 - #define BRCMF_ASSOC_PARAMS_FIXED_SIZE \ (sizeof(struct brcmf_assoc_params_le) - sizeof(u16)) @@ -230,6 +230,9 @@ struct parsed_vndr_ies { struct parsed_vndr_ie_info ie_info[VNDR_IE_PARSE_LIMIT]; }; +#define WLC_E_IF_ROLE_STA 0 /* Infra STA */ +#define WLC_E_IF_ROLE_AP 1 /* Access Point */ + static u8 nl80211_band_to_fwil(enum nl80211_band band) { switch (band) { @@ -1130,11 +1133,6 @@ brcmf_cfg80211_scan(struct wiphy *wiphy, struct cfg80211_scan_request *request) if (err) goto scan_out; - err = brcmf_vif_set_mgmt_ie(vif, BRCMF_VNDR_IE_PRBREQ_FLAG, - request->ie, request->ie_len); - if (err) - goto scan_out; - err = brcmf_do_escan(vif->ifp, request); if (err) goto scan_out; @@ -1284,7 +1282,33 @@ static int brcmf_set_pmk(struct brcmf_if *ifp, const u8 *pmk_data, u16 pmk_len) return err; } -static void brcmf_link_down(struct brcmf_cfg80211_vif *vif, u16 reason) +static int brcmf_set_sae_password(struct brcmf_if *ifp, const u8 *pwd_data, + u16 pwd_len) +{ + struct brcmf_pub *drvr = ifp->drvr; + struct brcmf_wsec_sae_pwd_le sae_pwd; + int err; + + if (pwd_len > BRCMF_WSEC_MAX_SAE_PASSWORD_LEN) { + bphy_err(drvr, "sae_password must be less than %d\n", + BRCMF_WSEC_MAX_SAE_PASSWORD_LEN); + return -EINVAL; + } + + sae_pwd.key_len = cpu_to_le16(pwd_len); + memcpy(sae_pwd.key, pwd_data, pwd_len); + + err = brcmf_fil_iovar_data_set(ifp, "sae_password", &sae_pwd, + sizeof(sae_pwd)); + if (err < 0) + bphy_err(drvr, "failed to set SAE password in firmware (len=%u)\n", + pwd_len); + + return err; +} + +static void brcmf_link_down(struct brcmf_cfg80211_vif *vif, u16 reason, + bool locally_generated) { struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(vif->wdev.wiphy); struct brcmf_pub *drvr = cfg->pub; @@ -1306,7 +1330,7 @@ static void brcmf_link_down(struct brcmf_cfg80211_vif *vif, u16 reason) if ((vif->wdev.iftype == NL80211_IFTYPE_STATION) || (vif->wdev.iftype == NL80211_IFTYPE_P2P_CLIENT)) cfg80211_disconnected(vif->wdev.netdev, reason, NULL, 0, - true, GFP_KERNEL); + locally_generated, GFP_KERNEL); } clear_bit(BRCMF_VIF_STATUS_CONNECTING, &vif->sme_state); clear_bit(BRCMF_SCAN_STATUS_SUPPRESS, &cfg->scan_status); @@ -1485,7 +1509,7 @@ brcmf_cfg80211_leave_ibss(struct wiphy *wiphy, struct net_device *ndev) return 0; } - brcmf_link_down(ifp->vif, WLAN_REASON_DEAUTH_LEAVING); + brcmf_link_down(ifp->vif, WLAN_REASON_DEAUTH_LEAVING, true); brcmf_net_setcarrier(ifp, false); brcmf_dbg(TRACE, "Exit\n"); @@ -1507,6 +1531,8 @@ static s32 brcmf_set_wpa_version(struct net_device *ndev, val = WPA_AUTH_PSK | WPA_AUTH_UNSPECIFIED; else if (sme->crypto.wpa_versions & NL80211_WPA_VERSION_2) val = WPA2_AUTH_PSK | WPA2_AUTH_UNSPECIFIED; + else if (sme->crypto.wpa_versions & NL80211_WPA_VERSION_3) + val = WPA3_AUTH_SAE_PSK; else val = WPA_AUTH_DISABLED; brcmf_dbg(CONN, "setting wpa_auth to 0x%0x\n", val); @@ -1539,6 +1565,10 @@ static s32 brcmf_set_auth_type(struct net_device *ndev, val = 1; brcmf_dbg(CONN, "shared key\n"); break; + case NL80211_AUTHTYPE_SAE: + val = 3; + brcmf_dbg(CONN, "SAE authentication\n"); + break; default: val = 2; brcmf_dbg(CONN, "automatic, auth type (%d)\n", sme->auth_type); @@ -1640,6 +1670,7 @@ brcmf_set_key_mgmt(struct net_device *ndev, struct cfg80211_connect_params *sme) struct brcmf_pub *drvr = ifp->drvr; s32 val; s32 err; + s32 okc_enable; const struct brcmf_tlv *rsn_ie; const u8 *ie; u32 ie_len; @@ -1649,6 +1680,8 @@ brcmf_set_key_mgmt(struct net_device *ndev, struct cfg80211_connect_params *sme) u16 count; profile->use_fwsup = BRCMF_PROFILE_FWSUP_NONE; + profile->is_ft = false; + profile->is_okc = false; if (!sme->crypto.n_akm_suites) return 0; @@ -1693,11 +1726,27 @@ brcmf_set_key_mgmt(struct net_device *ndev, struct cfg80211_connect_params *sme) break; case WLAN_AKM_SUITE_FT_8021X: val = WPA2_AUTH_UNSPECIFIED | WPA2_AUTH_FT; + profile->is_ft = true; if (sme->want_1x) profile->use_fwsup = BRCMF_PROFILE_FWSUP_1X; break; case WLAN_AKM_SUITE_FT_PSK: val = WPA2_AUTH_PSK | WPA2_AUTH_FT; + profile->is_ft = true; + break; + default: + bphy_err(drvr, "invalid cipher group (%d)\n", + sme->crypto.cipher_group); + return -EINVAL; + } + } else if (val & WPA3_AUTH_SAE_PSK) { + switch (sme->crypto.akm_suites[0]) { + case WLAN_AKM_SUITE_SAE: + val = WPA3_AUTH_SAE_PSK; + if (sme->crypto.sae_pwd) { + brcmf_dbg(INFO, "using SAE offload\n"); + profile->use_fwsup = BRCMF_PROFILE_FWSUP_SAE; + } break; default: bphy_err(drvr, "invalid cipher group (%d)\n", @@ -1706,8 +1755,17 @@ brcmf_set_key_mgmt(struct net_device *ndev, struct cfg80211_connect_params *sme) } } - if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_1X) + if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_1X) { brcmf_dbg(INFO, "using 1X offload\n"); + err = brcmf_fil_bsscfg_int_get(netdev_priv(ndev), "okc_enable", + &okc_enable); + if (err) { + bphy_err(drvr, "get okc_enable failed (%d)\n", err); + } else { + brcmf_dbg(INFO, "get okc_enable (%d)\n", okc_enable); + profile->is_okc = okc_enable; + } + } if (!brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP)) goto skip_mfp_config; @@ -1775,7 +1833,8 @@ brcmf_set_sharedkey(struct net_device *ndev, brcmf_dbg(CONN, "wpa_versions 0x%x cipher_pairwise 0x%x\n", sec->wpa_versions, sec->cipher_pairwise); - if (sec->wpa_versions & (NL80211_WPA_VERSION_1 | NL80211_WPA_VERSION_2)) + if (sec->wpa_versions & (NL80211_WPA_VERSION_1 | NL80211_WPA_VERSION_2 | + NL80211_WPA_VERSION_3)) return 0; if (!(sec->cipher_pairwise & @@ -1982,7 +2041,8 @@ brcmf_cfg80211_connect(struct wiphy *wiphy, struct net_device *ndev, goto done; } - if (sme->crypto.psk) { + if (sme->crypto.psk && + profile->use_fwsup != BRCMF_PROFILE_FWSUP_SAE) { if (WARN_ON(profile->use_fwsup != BRCMF_PROFILE_FWSUP_NONE)) { err = -EINVAL; goto done; @@ -2000,12 +2060,23 @@ brcmf_cfg80211_connect(struct wiphy *wiphy, struct net_device *ndev, } } - if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_PSK) { + if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_PSK) err = brcmf_set_pmk(ifp, sme->crypto.psk, BRCMF_WSEC_MAX_PSK_LEN); - if (err) + else if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_SAE) { + /* clean up user-space RSNE */ + if (brcmf_fil_iovar_data_set(ifp, "wpaie", NULL, 0)) { + bphy_err(drvr, "failed to clean up user-space RSNE\n"); goto done; + } + err = brcmf_set_sae_password(ifp, sme->crypto.sae_pwd, + sme->crypto.sae_pwd_len); + if (!err && sme->crypto.psk) + err = brcmf_set_pmk(ifp, sme->crypto.psk, + BRCMF_WSEC_MAX_PSK_LEN); } + if (err) + goto done; /* Join with specific BSSID and cached SSID * If SSID is zero join based on BSSID only @@ -2329,6 +2400,17 @@ brcmf_cfg80211_add_key(struct wiphy *wiphy, struct net_device *ndev, if (!ext_key) key->flags = BRCMF_PRIMARY_KEY; + if (params->seq && params->seq_len == 6) { + /* rx iv */ + u8 *ivptr; + + ivptr = (u8 *)params->seq; + key->rxiv.hi = (ivptr[5] << 24) | (ivptr[4] << 16) | + (ivptr[3] << 8) | ivptr[2]; + key->rxiv.lo = (ivptr[1] << 8) | ivptr[0]; + key->iv_initialized = true; + } + switch (params->cipher) { case WLAN_CIPHER_SUITE_WEP40: key->algo = CRYPTO_ALGO_WEP1; @@ -2776,7 +2858,7 @@ brcmf_cfg80211_set_power_mgmt(struct wiphy *wiphy, struct net_device *ndev, goto done; } - pm = enabled ? PM_FAST : PM_OFF; + pm = enabled ? ifp->drvr->settings->default_pm : PM_OFF; /* Do not enable the power save after assoc if it is a p2p interface */ if (ifp->vif->wdev.iftype == NL80211_IFTYPE_P2P_CLIENT) { brcmf_dbg(INFO, "Do not enable power save for P2P clients\n"); @@ -2791,12 +2873,6 @@ brcmf_cfg80211_set_power_mgmt(struct wiphy *wiphy, struct net_device *ndev, else bphy_err(drvr, "error (%d)\n", err); } - - err = brcmf_fil_iovar_int_set(ifp, "pm2_sleep_ret", - min_t(u32, timeout, BRCMF_PS_MAX_TIMEOUT_MS)); - if (err) - bphy_err(drvr, "Unable to set pm timeout, (%d)\n", err); - done: brcmf_dbg(TRACE, "Exit\n"); return err; @@ -2820,7 +2896,7 @@ static s32 brcmf_inform_single_bss(struct brcmf_cfg80211_info *cfg, if (le32_to_cpu(bi->length) > WL_BSS_INFO_MAX) { bphy_err(drvr, "Bss info is larger than buffer. Discarding\n"); - return 0; + return -EINVAL; } if (!bi->ctl_ch) { @@ -3651,10 +3727,24 @@ static s32 brcmf_cfg80211_resume(struct wiphy *wiphy) struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); struct net_device *ndev = cfg_to_ndev(cfg); struct brcmf_if *ifp = netdev_priv(ndev); + struct brcmf_pub *drvr = ifp->drvr; + struct brcmf_bus *bus_if = drvr->bus_if; + struct brcmf_cfg80211_info *config = drvr->config; + int retry = BRCMF_PM_WAIT_MAXRETRY; brcmf_dbg(TRACE, "Enter\n"); + config->pm_state = BRCMF_CFG80211_PM_STATE_RESUMING; + if (cfg->wowl.active) { + /* wait for bus resumed */ + while (retry && bus_if->state != BRCMF_BUS_UP) { + usleep_range(10000, 20000); + retry--; + } + if (!retry && bus_if->state != BRCMF_BUS_UP) + brcmf_err("timed out wait for bus resume\n"); + brcmf_report_wowl_wakeind(wiphy, ifp); brcmf_fil_iovar_int_set(ifp, "wowl_clear", 0); brcmf_config_wowl_pattern(ifp, "clr", NULL, 0, NULL, 0); @@ -3670,7 +3760,12 @@ static s32 brcmf_cfg80211_resume(struct wiphy *wiphy) brcmf_notify_sched_scan_results); cfg->wowl.nd_enabled = false; } + + /* disable packet filters */ + brcmf_pktfilter_enable(ifp->ndev, false); + } + config->pm_state = BRCMF_CFG80211_PM_STATE_RESUMED; return 0; } @@ -3728,6 +3823,9 @@ static void brcmf_configure_wowl(struct brcmf_cfg80211_info *cfg, brcmf_fil_iovar_int_set(ifp, "wowl_activate", 1); brcmf_bus_wowl_config(cfg->pub->bus_if, true); cfg->wowl.active = true; + + /* enable packet filters */ + brcmf_pktfilter_enable(ifp->ndev, true); } static s32 brcmf_cfg80211_suspend(struct wiphy *wiphy, @@ -3737,9 +3835,12 @@ static s32 brcmf_cfg80211_suspend(struct wiphy *wiphy, struct net_device *ndev = cfg_to_ndev(cfg); struct brcmf_if *ifp = netdev_priv(ndev); struct brcmf_cfg80211_vif *vif; + struct brcmf_cfg80211_info *config = ifp->drvr->config; brcmf_dbg(TRACE, "Enter\n"); + config->pm_state = BRCMF_CFG80211_PM_STATE_SUSPENDING; + /* if the primary net_device is not READY there is nothing * we can do but pray resume goes smoothly. */ @@ -3754,7 +3855,8 @@ static s32 brcmf_cfg80211_suspend(struct wiphy *wiphy, if (test_bit(BRCMF_SCAN_STATUS_BUSY, &cfg->scan_status)) brcmf_abort_scanning(cfg); - if (wowl == NULL) { + if (!wowl || !test_bit(BRCMF_VIF_STATUS_CONNECTED, + &ifp->vif->sme_state)) { brcmf_bus_wowl_config(cfg->pub->bus_if, false); list_for_each_entry(vif, &cfg->vif_list, list) { if (!test_bit(BRCMF_VIF_STATUS_READY, &vif->sme_state)) @@ -3763,7 +3865,7 @@ static s32 brcmf_cfg80211_suspend(struct wiphy *wiphy, * disassociate from AP to save power while system is * in suspended state */ - brcmf_link_down(vif, WLAN_REASON_UNSPECIFIED); + brcmf_link_down(vif, WLAN_REASON_UNSPECIFIED, true); /* Make sure WPA_Supplicant receives all the event * generated due to DISASSOC call to the fw to keep * the state fw and WPA_Supplicant state consistent @@ -3774,14 +3876,19 @@ static s32 brcmf_cfg80211_suspend(struct wiphy *wiphy, brcmf_set_mpc(ifp, 1); } else { - /* Configure WOWL paramaters */ - brcmf_configure_wowl(cfg, ifp, wowl); + if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_WOWL)) + /* Configure WOWL parameters */ + brcmf_configure_wowl(cfg, ifp, wowl); } exit: - brcmf_dbg(TRACE, "Exit\n"); + /* set cfg80211 pm state to cfg80211 suspended state */ + config->pm_state = BRCMF_CFG80211_PM_STATE_SUSPENDED; + /* clear any scanning activity */ cfg->scan_status = 0; + + brcmf_dbg(TRACE, "Exit\n"); return 0; } @@ -4092,6 +4199,10 @@ brcmf_configure_wpaie(struct brcmf_if *ifp, brcmf_dbg(TRACE, "RSN_AKM_MFP_1X\n"); wpa_auth |= WPA2_AUTH_1X_SHA256; break; + case RSN_AKM_SAE: + brcmf_dbg(TRACE, "RSN_AKM_SAE\n"); + wpa_auth |= WPA3_AUTH_SAE_PSK; + break; default: bphy_err(drvr, "Invalid key mgmt info\n"); } @@ -4109,11 +4220,12 @@ brcmf_configure_wpaie(struct brcmf_if *ifp, brcmf_dbg(TRACE, "MFP Required\n"); mfp = BRCMF_MFP_REQUIRED; /* Firmware only supports mfp required in - * combination with WPA2_AUTH_PSK_SHA256 or - * WPA2_AUTH_1X_SHA256. + * combination with WPA2_AUTH_PSK_SHA256, + * WPA2_AUTH_1X_SHA256, or WPA3_AUTH_SAE_PSK. */ if (!(wpa_auth & (WPA2_AUTH_PSK_SHA256 | - WPA2_AUTH_1X_SHA256))) { + WPA2_AUTH_1X_SHA256 | + WPA3_AUTH_SAE_PSK))) { err = -EINVAL; goto exit; } @@ -4316,6 +4428,11 @@ s32 brcmf_vif_set_mgmt_ie(struct brcmf_cfg80211_vif *vif, s32 pktflag, mgmt_ie_len = &saved_ie->assoc_req_ie_len; mgmt_ie_buf_len = sizeof(saved_ie->assoc_req_ie); break; + case BRCMF_VNDR_IE_ASSOCRSP_FLAG: + mgmt_ie_buf = saved_ie->assoc_res_ie; + mgmt_ie_len = &saved_ie->assoc_res_ie_len; + mgmt_ie_buf_len = sizeof(saved_ie->assoc_res_ie); + break; default: err = -EPERM; bphy_err(drvr, "not suitable type\n"); @@ -4462,6 +4579,57 @@ brcmf_config_ap_mgmt_ie(struct brcmf_cfg80211_vif *vif, else brcmf_dbg(TRACE, "Applied Vndr IEs for Probe Resp\n"); + /* Set Assoc Response IEs to FW */ + err = brcmf_vif_set_mgmt_ie(vif, BRCMF_VNDR_IE_ASSOCRSP_FLAG, + beacon->assocresp_ies, + beacon->assocresp_ies_len); + if (err) + brcmf_err("Set Assoc Resp IE Failed\n"); + else + brcmf_dbg(TRACE, "Applied Vndr IEs for Assoc Resp\n"); + + return err; +} + +static s32 +brcmf_parse_configure_security(struct brcmf_if *ifp, + struct cfg80211_ap_settings *settings, + enum nl80211_iftype dev_role) +{ + const struct brcmf_tlv *rsn_ie; + const struct brcmf_vs_tlv *wpa_ie; + s32 err = 0; + + /* find the RSN_IE */ + rsn_ie = brcmf_parse_tlvs((u8 *)settings->beacon.tail, + settings->beacon.tail_len, WLAN_EID_RSN); + + /* find the WPA_IE */ + wpa_ie = brcmf_find_wpaie((u8 *)settings->beacon.tail, + settings->beacon.tail_len); + + if (wpa_ie || rsn_ie) { + brcmf_dbg(TRACE, "WPA(2) IE is found\n"); + if (wpa_ie) { + /* WPA IE */ + err = brcmf_configure_wpaie(ifp, wpa_ie, false); + if (err < 0) + return err; + } else { + struct brcmf_vs_tlv *tmp_ie; + + tmp_ie = (struct brcmf_vs_tlv *)rsn_ie; + + /* RSN IE */ + err = brcmf_configure_wpaie(ifp, tmp_ie, true); + if (err < 0) + return err; + } + } else { + brcmf_dbg(TRACE, "No WPA(2) IEs found\n"); + brcmf_configure_opensecurity(ifp); + } + return err; } @@ -4473,12 +4641,12 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); struct brcmf_if *ifp = netdev_priv(ndev); struct brcmf_pub *drvr = cfg->pub; + struct brcmf_cfg80211_profile *profile = &ifp->vif->profile; + struct cfg80211_crypto_settings *crypto = &settings->crypto; const struct brcmf_tlv *ssid_ie; const struct brcmf_tlv *country_ie; struct brcmf_ssid_le ssid_le; s32 err = -EPERM; - const struct brcmf_tlv *rsn_ie; - const struct brcmf_vs_tlv *wpa_ie; struct brcmf_join_params join_params; enum nl80211_iftype dev_role; struct brcmf_fil_bss_enable_le bss_enable; @@ -4496,6 +4664,7 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, settings->inactivity_timeout); dev_role = ifp->vif->wdev.iftype; mbss = ifp->vif->mbss; + brcmf_dbg(TRACE, "mbss %s\n", mbss ? "enabled" : "disabled"); /* store current 11d setting */ if (brcmf_fil_cmd_int_get(ifp, BRCMF_C_GET_REGULATORY, @@ -4532,36 +4701,6 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, brcmf_configure_arp_nd_offload(ifp, false); } - /* find the RSN_IE */ - rsn_ie = brcmf_parse_tlvs((u8 *)settings->beacon.tail, - settings->beacon.tail_len, WLAN_EID_RSN); - - /* find the WPA_IE */ - wpa_ie = brcmf_find_wpaie((u8 *)settings->beacon.tail, - settings->beacon.tail_len); - - if ((wpa_ie != NULL || rsn_ie != NULL)) { - brcmf_dbg(TRACE, "WPA(2) IE is found\n"); - if (wpa_ie != NULL) { - /* WPA IE */ - err = brcmf_configure_wpaie(ifp, wpa_ie, false); - if (err < 0) - goto exit; - } else { - struct brcmf_vs_tlv *tmp_ie; - - tmp_ie = (struct brcmf_vs_tlv *)rsn_ie; - - /* RSN IE */ - err = brcmf_configure_wpaie(ifp, tmp_ie, true); - if (err < 0) - goto exit; - } - } else { - brcmf_dbg(TRACE, "No WPA(2) IEs found\n"); - brcmf_configure_opensecurity(ifp); - } - /* Parameters shared by all radio interfaces */ if (!mbss) { if ((supports_11d) && (is_11d != ifp->vif->is_11d)) { @@ -4592,9 +4731,7 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, } } - if ((dev_role == NL80211_IFTYPE_AP) && - ((ifp->ifidx == 0) || - !brcmf_feat_is_enabled(ifp, BRCMF_FEAT_RSDB))) { + if (dev_role == NL80211_IFTYPE_AP && ifp->ifidx == 0) { err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_DOWN, 1); if (err < 0) { bphy_err(drvr, "BRCMF_C_DOWN error %d\n", @@ -4614,7 +4751,7 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, err = -EINVAL; goto exit; } - + ifp->isap = false; /* Interface specific setup */ if (dev_role == NL80211_IFTYPE_AP) { if ((brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MBSS)) && (!mbss)) @@ -4642,6 +4779,33 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, bphy_err(drvr, "BRCMF_C_UP error (%d)\n", err); goto exit; } + + if (crypto->psk) { + brcmf_dbg(INFO, "using PSK offload\n"); + profile->use_fwauth |= BIT(BRCMF_PROFILE_FWAUTH_PSK); + err = brcmf_set_pmk(ifp, crypto->psk, + BRCMF_WSEC_MAX_PSK_LEN); + if (err < 0) + goto exit; + } + if (crypto->sae_pwd) { + brcmf_dbg(INFO, "using SAE offload\n"); + profile->use_fwauth |= BIT(BRCMF_PROFILE_FWAUTH_SAE); + err = brcmf_set_sae_password(ifp, crypto->sae_pwd, + crypto->sae_pwd_len); + if (err < 0) + goto exit; + } + if (profile->use_fwauth == 0) + profile->use_fwauth = BIT(BRCMF_PROFILE_FWAUTH_NONE); + + err = brcmf_parse_configure_security(ifp, settings, + NL80211_IFTYPE_AP); + if (err < 0) { + bphy_err(drvr, "brcmf_parse_configure_security error\n"); + goto exit; + } + /* On DOWN the firmware removes the WEP keys, reconfigure * them if they were set. */ @@ -4658,14 +4822,16 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, goto exit; } - if (settings->hidden_ssid) { - err = brcmf_fil_iovar_int_set(ifp, "closednet", 1); - if (err) { - bphy_err(drvr, "closednet error (%d)\n", err); - goto exit; - } + err = brcmf_fil_iovar_int_set(ifp, "closednet", + settings->hidden_ssid); + if (err) { + bphy_err(drvr, "%s closednet error (%d)\n", + settings->hidden_ssid ? + "enabled" : "disabled", + err); + goto exit; } - + ifp->isap = true; brcmf_dbg(TRACE, "AP mode configuration complete\n"); } else if (dev_role == NL80211_IFTYPE_P2P_GO) { err = brcmf_fil_iovar_int_set(ifp, "chanspec", chanspec); @@ -4674,6 +4840,14 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, chanspec, err); goto exit; } + + err = brcmf_parse_configure_security(ifp, settings, + NL80211_IFTYPE_P2P_GO); + if (err < 0) { + brcmf_err("brcmf_parse_configure_security error\n"); + goto exit; + } + err = brcmf_fil_bsscfg_data_set(ifp, "ssid", &ssid_le, sizeof(ssid_le)); if (err < 0) { @@ -4689,6 +4863,7 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev, goto exit; } + ifp->isap = true; brcmf_dbg(TRACE, "GO mode configuration complete\n"); } else { WARN_ON(1); @@ -4702,6 +4877,9 @@ exit: if ((err) && (!mbss)) { brcmf_set_mpc(ifp, 1); brcmf_configure_arp_nd_offload(ifp, true); + } else { + cfg->num_softap++; + brcmf_dbg(TRACE, "Num of SoftAP %u\n", cfg->num_softap); } return err; } @@ -4711,9 +4889,11 @@ static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); struct brcmf_if *ifp = netdev_priv(ndev); struct brcmf_pub *drvr = cfg->pub; + struct brcmf_cfg80211_profile *profile = &ifp->vif->profile; s32 err; struct brcmf_fil_bss_enable_le bss_enable; struct brcmf_join_params join_params; + s32 apsta = 0; brcmf_dbg(TRACE, "Enter\n"); @@ -4722,6 +4902,35 @@ static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) /* first to make sure they get processed by fw. */ msleep(400); + cfg->num_softap--; + + /* Clear bss configuration and SSID */ + bss_enable.bsscfgidx = cpu_to_le32(ifp->bsscfgidx); + bss_enable.enable = cpu_to_le32(0); + err = brcmf_fil_iovar_data_set(ifp, "bss", &bss_enable, + sizeof(bss_enable)); + if (err < 0) + brcmf_err("bss_enable config failed %d\n", err); + + memset(&join_params, 0, sizeof(join_params)); + err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SET_SSID, + &join_params, sizeof(join_params)); + if (err < 0) + bphy_err(drvr, "SET SSID error (%d)\n", err); + + if (cfg->num_softap) { + brcmf_dbg(TRACE, "Num of SoftAP %u\n", cfg->num_softap); + return 0; + } + + if (profile->use_fwauth != BIT(BRCMF_PROFILE_FWAUTH_NONE)) { + if (profile->use_fwauth & BIT(BRCMF_PROFILE_FWAUTH_PSK)) + brcmf_set_pmk(ifp, NULL, 0); + if (profile->use_fwauth & BIT(BRCMF_PROFILE_FWAUTH_SAE)) + brcmf_set_sae_password(ifp, NULL, 0); + profile->use_fwauth = BIT(BRCMF_PROFILE_FWAUTH_NONE); + } + if (ifp->vif->mbss) { err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_DOWN, 1); return err; @@ -4731,17 +4940,18 @@ static int brcmf_cfg80211_stop_ap(struct wiphy *wiphy, struct net_device *ndev) if (ifp->bsscfgidx == 0) brcmf_fil_iovar_int_set(ifp, "closednet", 0); - memset(&join_params, 0, sizeof(join_params)); - err = brcmf_fil_cmd_data_set(ifp, BRCMF_C_SET_SSID, - &join_params, sizeof(join_params)); - if (err < 0) - bphy_err(drvr, "SET SSID error (%d)\n", err); - err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_DOWN, 1); - if (err < 0) - bphy_err(drvr, "BRCMF_C_DOWN error %d\n", err); - err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_AP, 0); + err = brcmf_fil_iovar_int_get(ifp, "apsta", &apsta); if (err < 0) - bphy_err(drvr, "setting AP mode failed %d\n", err); + brcmf_err("wl apsta failed (%d)\n", err); + + if (!apsta) { + err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_DOWN, 1); + if (err < 0) + bphy_err(drvr, "BRCMF_C_DOWN error %d\n", err); + err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_AP, 0); + if (err < 0) + bphy_err(drvr, "Set AP mode error %d\n", err); + } if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MBSS)) brcmf_fil_iovar_int_set(ifp, "mbss", 0); brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_REGULATORY, @@ -5216,17 +5426,27 @@ static int brcmf_cfg80211_set_pmk(struct wiphy *wiphy, struct net_device *dev, const struct cfg80211_pmk_conf *conf) { struct brcmf_if *ifp; + struct brcmf_pub *drvr; + int ret; brcmf_dbg(TRACE, "enter\n"); /* expect using firmware supplicant for 1X */ ifp = netdev_priv(dev); + drvr = ifp->drvr; if (WARN_ON(ifp->vif->profile.use_fwsup != BRCMF_PROFILE_FWSUP_1X)) return -EINVAL; if (conf->pmk_len > BRCMF_WSEC_MAX_PSK_LEN) return -ERANGE; + if (ifp->vif->profile.is_okc) { + ret = brcmf_fil_iovar_data_set(ifp, "okc_info_pmk", conf->pmk, + conf->pmk_len); + if (ret < 0) + bphy_err(drvr, "okc_info_pmk iovar failed: ret=%d\n", ret); + } + return brcmf_set_pmk(ifp, conf->pmk, conf->pmk_len); } @@ -5243,6 +5463,37 @@ static int brcmf_cfg80211_del_pmk(struct wiphy *wiphy, struct net_device *dev, return brcmf_set_pmk(ifp, NULL, 0); } +static int +brcmf_cfg80211_change_bss(struct wiphy *wiphy, struct net_device *dev, + struct bss_parameters *params) +{ + struct brcmf_if *ifp; + int ret = 0; + u32 ap_isolate, val; + + brcmf_dbg(TRACE, "Enter\n"); + ifp = netdev_priv(dev); + if (params->ap_isolate >= 0) { + ap_isolate = (u32)params->ap_isolate; + ret = brcmf_fil_iovar_int_set(ifp, "ap_isolate", ap_isolate); + if (ret < 0) + brcmf_err("ap_isolate iovar failed: ret=%d\n", ret); + } + + /* Get ap_isolate value from firmware to detemine whether fmac */ + /* driver supports packet forwarding. */ + if (brcmf_fil_iovar_int_get(ifp, "ap_isolate", &val) == 0) { + ifp->fmac_pkt_fwd_en = + ((params->ap_isolate == 0) && (val == 1)) ? + true : false; + } else { + brcmf_err("get ap_isolate iovar failed: ret=%d\n", ret); + ifp->fmac_pkt_fwd_en = false; + } + + return ret; +} + static struct cfg80211_ops brcmf_cfg80211_ops = { .add_virtual_intf = brcmf_cfg80211_add_iface, .del_virtual_intf = brcmf_cfg80211_del_iface, @@ -5288,6 +5539,7 @@ static struct cfg80211_ops brcmf_cfg80211_ops = { .update_connect_params = brcmf_cfg80211_update_conn_params, .set_pmk = brcmf_cfg80211_set_pmk, .del_pmk = brcmf_cfg80211_del_pmk, + .change_bss = brcmf_cfg80211_change_bss, }; struct cfg80211_ops *brcmf_cfg80211_get_ops(struct brcmf_mp_device *settings) @@ -5309,6 +5561,7 @@ struct brcmf_cfg80211_vif *brcmf_alloc_vif(struct brcmf_cfg80211_info *cfg, struct brcmf_cfg80211_vif *vif_walk; struct brcmf_cfg80211_vif *vif; bool mbss; + struct brcmf_if *ifp = brcmf_get_ifp(cfg->pub, 0); brcmf_dbg(TRACE, "allocating virtual interface (size=%zu)\n", sizeof(*vif)); @@ -5321,7 +5574,8 @@ struct brcmf_cfg80211_vif *brcmf_alloc_vif(struct brcmf_cfg80211_info *cfg, brcmf_init_prof(&vif->profile); - if (type == NL80211_IFTYPE_AP) { + if (type == NL80211_IFTYPE_AP && + brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MBSS)) { mbss = false; list_for_each_entry(vif_walk, &cfg->vif_list, list) { if (vif_walk->wdev.iftype == NL80211_IFTYPE_AP) { @@ -5350,8 +5604,10 @@ void brcmf_cfg80211_free_netdev(struct net_device *ndev) ifp = netdev_priv(ndev); vif = ifp->vif; - if (vif) + if (vif) { brcmf_free_vif(vif); + ifp->vif = NULL; + } } static bool brcmf_is_linkup(struct brcmf_cfg80211_vif *vif, @@ -5360,14 +5616,16 @@ static bool brcmf_is_linkup(struct brcmf_cfg80211_vif *vif, u32 event = e->event_code; u32 status = e->status; - if (vif->profile.use_fwsup == BRCMF_PROFILE_FWSUP_PSK && + if ((vif->profile.use_fwsup == BRCMF_PROFILE_FWSUP_PSK || + vif->profile.use_fwsup == BRCMF_PROFILE_FWSUP_SAE) && event == BRCMF_E_PSK_SUP && status == BRCMF_E_STATUS_FWSUP_COMPLETED) set_bit(BRCMF_VIF_STATUS_EAP_SUCCESS, &vif->sme_state); if (event == BRCMF_E_SET_SSID && status == BRCMF_E_STATUS_SUCCESS) { brcmf_dbg(CONN, "Processing set ssid\n"); memcpy(vif->profile.bssid, e->addr, ETH_ALEN); - if (vif->profile.use_fwsup != BRCMF_PROFILE_FWSUP_PSK) + if (vif->profile.use_fwsup != BRCMF_PROFILE_FWSUP_PSK && + vif->profile.use_fwsup != BRCMF_PROFILE_FWSUP_SAE) return true; set_bit(BRCMF_VIF_STATUS_ASSOC_SUCCESS, &vif->sme_state); @@ -5435,12 +5693,153 @@ static void brcmf_clear_assoc_ies(struct brcmf_cfg80211_info *cfg) conn_info->resp_ie_len = 0; } +u8 brcmf_map_prio_to_prec(void *config, u8 prio) +{ + struct brcmf_cfg80211_info *cfg = (struct brcmf_cfg80211_info *)config; + + if (!cfg) + return (prio == PRIO_8021D_NONE || prio == PRIO_8021D_BE) ? + (prio ^ 2) : prio; + + /* For those AC(s) with ACM flag set to 1, convert its 4-level priority + * to an 8-level precedence which is the same as BE's + */ + if (prio > PRIO_8021D_EE && + cfg->ac_priority[prio] == cfg->ac_priority[PRIO_8021D_BE]) + return cfg->ac_priority[prio] * 2; + + /* Conversion of 4-level priority to 8-level precedence */ + if (prio == PRIO_8021D_BE || prio == PRIO_8021D_BK || + prio == PRIO_8021D_CL || prio == PRIO_8021D_VO) + return cfg->ac_priority[prio] * 2; + else + return cfg->ac_priority[prio] * 2 + 1; +} + +u8 brcmf_map_prio_to_aci(void *config, u8 prio) +{ + /* Prio here refers to the 802.1d priority in range of 0 to 7. + * ACI here refers to the WLAN AC Index in range of 0 to 3. + * This function will return ACI corresponding to input prio. + */ + struct brcmf_cfg80211_info *cfg = (struct brcmf_cfg80211_info *)config; + + if (cfg) + return cfg->ac_priority[prio]; + + return prio; +} + +static void brcmf_init_wmm_prio(u8 *priority) +{ + /* Initialize AC priority array to default + * 802.1d priority as per following table: + * 802.1d prio 0,3 maps to BE + * 802.1d prio 1,2 maps to BK + * 802.1d prio 4,5 maps to VI + * 802.1d prio 6,7 maps to VO + */ + priority[0] = BRCMF_FWS_FIFO_AC_BE; + priority[3] = BRCMF_FWS_FIFO_AC_BE; + priority[1] = BRCMF_FWS_FIFO_AC_BK; + priority[2] = BRCMF_FWS_FIFO_AC_BK; + priority[4] = BRCMF_FWS_FIFO_AC_VI; + priority[5] = BRCMF_FWS_FIFO_AC_VI; + priority[6] = BRCMF_FWS_FIFO_AC_VO; + priority[7] = BRCMF_FWS_FIFO_AC_VO; +} + +static void brcmf_wifi_prioritize_acparams(const + struct brcmf_cfg80211_edcf_acparam *acp, u8 *priority) +{ + u8 aci; + u8 aifsn; + u8 ecwmin; + u8 ecwmax; + u8 acm; + u8 ranking_basis[EDCF_AC_COUNT]; + u8 aci_prio[EDCF_AC_COUNT]; /* AC_BE, AC_BK, AC_VI, AC_VO */ + u8 index; + + for (aci = 0; aci < EDCF_AC_COUNT; aci++, acp++) { + aifsn = acp->ACI & EDCF_AIFSN_MASK; + acm = (acp->ACI & EDCF_ACM_MASK) ? 1 : 0; + ecwmin = acp->ECW & EDCF_ECWMIN_MASK; + ecwmax = (acp->ECW & EDCF_ECWMAX_MASK) >> EDCF_ECWMAX_SHIFT; + brcmf_dbg(CONN, "ACI %d aifsn %d acm %d ecwmin %d ecwmax %d\n", + aci, aifsn, acm, ecwmin, ecwmax); + /* Default AC_VO will be the lowest ranking value */ + ranking_basis[aci] = aifsn + ecwmin + ecwmax; + /* Initialise priority starting at 0 (AC_BE) */ + aci_prio[aci] = 0; + + /* If ACM is set, STA can't use this AC as per 802.11. + * Change the ranking to BE + */ + if (aci != AC_BE && aci != AC_BK && acm == 1) + ranking_basis[aci] = ranking_basis[AC_BE]; + } + + /* Ranking method which works for AC priority + * swapping when values for cwmin, cwmax and aifsn are varied + * Compare each aci_prio against each other aci_prio + */ + for (aci = 0; aci < EDCF_AC_COUNT; aci++) { + for (index = 0; index < EDCF_AC_COUNT; index++) { + if (index != aci) { + /* Smaller ranking value has higher priority, + * so increment priority for each ACI which has + * a higher ranking value + */ + if (ranking_basis[aci] < ranking_basis[index]) + aci_prio[aci]++; + } + } + } + + /* By now, aci_prio[] will be in range of 0 to 3. + * Use ACI prio to get the new priority value for + * each 802.1d traffic type, in this range. + */ + if (!(aci_prio[AC_BE] == aci_prio[AC_BK] && + aci_prio[AC_BK] == aci_prio[AC_VI] && + aci_prio[AC_VI] == aci_prio[AC_VO])) { + + /* 802.1d 0,3 maps to BE */ + priority[0] = aci_prio[AC_BE]; + priority[3] = aci_prio[AC_BE]; + + /* 802.1d 1,2 maps to BK */ + priority[1] = aci_prio[AC_BK]; + priority[2] = aci_prio[AC_BK]; + + /* 802.1d 4,5 maps to VO */ + priority[4] = aci_prio[AC_VI]; + priority[5] = aci_prio[AC_VI]; + + /* 802.1d 6,7 maps to VO */ + priority[6] = aci_prio[AC_VO]; + priority[7] = aci_prio[AC_VO]; + + } else { + /* Initialize to default priority */ + brcmf_init_wmm_prio(priority); + } + + brcmf_dbg(CONN, "Adj prio BE 0->%d, BK 1->%d, BK 2->%d, BE 3->%d\n", + priority[0], priority[1], priority[2], priority[3]); + + brcmf_dbg(CONN, "Adj prio VI 4->%d, VI 5->%d, VO 6->%d, VO 7->%d\n", + priority[4], priority[5], priority[6], priority[7]); +} + static s32 brcmf_get_assoc_ies(struct brcmf_cfg80211_info *cfg, struct brcmf_if *ifp) { struct brcmf_pub *drvr = cfg->pub; struct brcmf_cfg80211_assoc_ielen_le *assoc_info; struct brcmf_cfg80211_connect_info *conn_info = cfg_to_conn(cfg); + struct brcmf_cfg80211_edcf_acparam edcf_acparam_info[EDCF_AC_COUNT]; u32 req_len; u32 resp_len; s32 err = 0; @@ -5489,6 +5888,17 @@ static s32 brcmf_get_assoc_ies(struct brcmf_cfg80211_info *cfg, GFP_KERNEL); if (!conn_info->resp_ie) conn_info->resp_ie_len = 0; + + err = brcmf_fil_iovar_data_get(ifp, "wme_ac_sta", + edcf_acparam_info, + sizeof(edcf_acparam_info)); + if (err) { + brcmf_err("could not get wme_ac_sta (%d)\n", err); + return err; + } + + brcmf_wifi_prioritize_acparams(edcf_acparam_info, + cfg->ac_priority); } else { conn_info->resp_ie_len = 0; conn_info->resp_ie = NULL; @@ -5499,6 +5909,47 @@ static s32 brcmf_get_assoc_ies(struct brcmf_cfg80211_info *cfg, return err; } +static bool +brcmf_has_pmkid(const u8 *parse, u32 len) +{ + const struct brcmf_tlv *rsn_ie; + const u8 *ie; + u32 ie_len; + u32 offset; + u16 count; + + rsn_ie = brcmf_parse_tlvs(parse, len, WLAN_EID_RSN); + if (!rsn_ie) + goto done; + ie = (const u8 *)rsn_ie; + ie_len = rsn_ie->len + TLV_HDR_LEN; + /* Skip group data cipher suite */ + offset = TLV_HDR_LEN + WPA_IE_VERSION_LEN + WPA_IE_MIN_OUI_LEN; + if (offset + WPA_IE_SUITE_COUNT_LEN >= ie_len) + goto done; + /* Skip pairwise cipher suite(s) */ + count = ie[offset] + (ie[offset + 1] << 8); + offset += WPA_IE_SUITE_COUNT_LEN + (count * WPA_IE_MIN_OUI_LEN); + if (offset + WPA_IE_SUITE_COUNT_LEN >= ie_len) + goto done; + /* Skip auth key management suite(s) */ + count = ie[offset] + (ie[offset + 1] << 8); + offset += WPA_IE_SUITE_COUNT_LEN + (count * WPA_IE_MIN_OUI_LEN); + if (offset + RSN_CAP_LEN >= ie_len) + goto done; + /* Skip rsn capabilities */ + offset += RSN_CAP_LEN; + if (offset + RSN_PMKID_COUNT_LEN > ie_len) + goto done; + /* Extract PMKID count */ + count = ie[offset] + (ie[offset + 1] << 8); + if (count) + return true; + +done: + return false; +} + static s32 brcmf_bss_roaming_done(struct brcmf_cfg80211_info *cfg, struct net_device *ndev, @@ -5559,6 +6010,11 @@ done: roam_info.resp_ie = conn_info->resp_ie; roam_info.resp_ie_len = conn_info->resp_ie_len; + if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_1X && + (brcmf_has_pmkid(roam_info.req_ie, roam_info.req_ie_len) || + profile->is_ft || profile->is_okc)) + roam_info.authorized = true; + cfg80211_roamed(ndev, &roam_info, GFP_KERNEL); brcmf_dbg(CONN, "Report roaming result\n"); @@ -5596,6 +6052,11 @@ brcmf_bss_connect_done(struct brcmf_cfg80211_info *cfg, conn_params.req_ie_len = conn_info->req_ie_len; conn_params.resp_ie = conn_info->resp_ie; conn_params.resp_ie_len = conn_info->resp_ie_len; + + if (profile->use_fwsup == BRCMF_PROFILE_FWSUP_1X && + brcmf_has_pmkid(conn_params.req_ie, conn_params.req_ie_len)) + conn_params.authorized = true; + cfg80211_connect_done(ndev, &conn_params, GFP_KERNEL); brcmf_dbg(CONN, "Report connect result - connection %s\n", completed ? "succeeded" : "failed"); @@ -5668,6 +6129,14 @@ brcmf_notify_connect_status(struct brcmf_if *ifp, } if (brcmf_is_apmode(ifp->vif)) { + if (e->event_code == BRCMF_E_ASSOC_IND || + e->event_code == BRCMF_E_REASSOC_IND) { + brcmf_findadd_sta(ifp, e->addr); + } else if ((e->event_code == BRCMF_E_DISASSOC_IND) || + (e->event_code == BRCMF_E_DEAUTH_IND) || + (e->event_code == BRCMF_E_DEAUTH)) { + brcmf_del_sta(ifp, e->addr); + } err = brcmf_notify_connect_status_ap(cfg, ndev, e, data); } else if (brcmf_is_linkup(ifp->vif, e)) { brcmf_dbg(CONN, "Linkup\n"); @@ -5685,10 +6154,19 @@ brcmf_notify_connect_status(struct brcmf_if *ifp, brcmf_net_setcarrier(ifp, true); } else if (brcmf_is_linkdown(e)) { brcmf_dbg(CONN, "Linkdown\n"); - if (!brcmf_is_ibssmode(ifp->vif)) { + if (!brcmf_is_ibssmode(ifp->vif) && + test_bit(BRCMF_VIF_STATUS_CONNECTED, + &ifp->vif->sme_state)) { + if (memcmp(profile->bssid, e->addr, ETH_ALEN)) + return err; + brcmf_bss_connect_done(cfg, ndev, e, false); brcmf_link_down(ifp->vif, - brcmf_map_fw_linkdown_reason(e)); + brcmf_map_fw_linkdown_reason(e), + e->event_code & + (BRCMF_E_DEAUTH_IND | + BRCMF_E_DISASSOC_IND) + ? false : true); brcmf_init_prof(ndev_to_prof(ndev)); if (ndev != cfg_to_ndev(cfg)) complete(&cfg->vif_disabled); @@ -5751,6 +6229,9 @@ static s32 brcmf_notify_vif_event(struct brcmf_if *ifp, struct brcmf_if_event *ifevent = (struct brcmf_if_event *)data; struct brcmf_cfg80211_vif_event *event = &cfg->vif_event; struct brcmf_cfg80211_vif *vif; + enum nl80211_iftype iftype = NL80211_IFTYPE_UNSPECIFIED; + bool vif_pend = false; + int err; brcmf_dbg(TRACE, "Enter: action %u flags %u ifidx %u bsscfgidx %u\n", ifevent->action, ifevent->flags, ifevent->ifidx, @@ -5763,9 +6244,28 @@ static s32 brcmf_notify_vif_event(struct brcmf_if *ifp, switch (ifevent->action) { case BRCMF_E_IF_ADD: /* waiting process may have timed out */ - if (!cfg->vif_event.vif) { + if (!vif) { + /* handle IF_ADD event from firmware */ spin_unlock(&event->vif_event_lock); - return -EBADF; + vif_pend = true; + if (ifevent->role == WLC_E_IF_ROLE_STA) + iftype = NL80211_IFTYPE_STATION; + else if (ifevent->role == WLC_E_IF_ROLE_AP) + iftype = NL80211_IFTYPE_AP; + else + vif_pend = false; + + if (vif_pend) { + vif = brcmf_alloc_vif(cfg, iftype); + if (IS_ERR(vif)) { + brcmf_err("Role:%d failed to alloc vif\n", + ifevent->role); + return PTR_ERR(vif); + } + } else { + brcmf_err("Invalid Role:%d\n", ifevent->role); + return -EBADF; + } } ifp->vif = vif; @@ -5775,6 +6275,18 @@ static s32 brcmf_notify_vif_event(struct brcmf_if *ifp, ifp->ndev->ieee80211_ptr = &vif->wdev; SET_NETDEV_DEV(ifp->ndev, wiphy_dev(cfg->wiphy)); } + + if (vif_pend) { + err = brcmf_net_attach(ifp, false); + if (err) { + brcmf_err("netdevice register failed with err:%d\n", + err); + brcmf_free_vif(vif); + free_netdev(ifp->ndev); + } + return err; + } + spin_unlock(&event->vif_event_lock); wake_up(&event->vif_wq); return 0; @@ -5900,6 +6412,7 @@ static s32 wl_init_priv(struct brcmf_cfg80211_info *cfg) mutex_init(&cfg->usr_sync); brcmf_init_escan(cfg); brcmf_init_conf(cfg->conf); + brcmf_init_wmm_prio(cfg->ac_priority); init_completion(&cfg->vif_disabled); return err; } @@ -6462,6 +6975,9 @@ brcmf_txrx_stypes[NUM_NL80211_IFTYPES] = { * #STA <= 1, #AP <= 1, channels = 1, 2 total * #AP <= 4, matching BI, channels = 1, 4 total * + * no p2p and rsdb: + * #STA <= 1, #AP <= 2, channels = 2, 3 total + * * p2p, no mchan, and mbss: * * #STA <= 1, #P2P-DEV <= 1, #{P2P-CL, P2P-GO} <= 1, channels = 1, 3 total @@ -6473,6 +6989,16 @@ brcmf_txrx_stypes[NUM_NL80211_IFTYPES] = { * #STA <= 1, #P2P-DEV <= 1, #{P2P-CL, P2P-GO} <= 1, channels = 2, 3 total * #STA <= 1, #P2P-DEV <= 1, #AP <= 1, #P2P-CL <= 1, channels = 1, 4 total * #AP <= 4, matching BI, channels = 1, 4 total + * + * p2p, rsdb, and no mbss: + * #STA <= 1, #P2P-DEV <= 1, #{P2P-CL, P2P-GO} <= 2, AP <= 2, + * channels = 2, 4 total + * + * p2p, rsdb, mbss + * #STA <= 1, #P2P-DEV <= 1, #{P2P-CL, P2P-GO} <= 2, AP <= 2, + * channels = 2, 4 total + * #AP <= 4, matching BI, channels = 1, 4 total + * */ static int brcmf_setup_ifmodes(struct wiphy *wiphy, struct brcmf_if *ifp) { @@ -6480,13 +7006,14 @@ static int brcmf_setup_ifmodes(struct wiphy *wiphy, struct brcmf_if *ifp) struct ieee80211_iface_limit *c0_limits = NULL; struct ieee80211_iface_limit *p2p_limits = NULL; struct ieee80211_iface_limit *mbss_limits = NULL; - bool mbss, p2p; + bool mbss, p2p, rsdb; int i, c, n_combos; mbss = brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MBSS); p2p = brcmf_feat_is_enabled(ifp, BRCMF_FEAT_P2P); + rsdb = brcmf_feat_is_enabled(ifp, BRCMF_FEAT_RSDB); - n_combos = 1 + !!p2p + !!mbss; + n_combos = 1 + !!(p2p && !rsdb) + !!mbss; combo = kcalloc(n_combos, sizeof(*combo), GFP_KERNEL); if (!combo) goto err; @@ -6497,16 +7024,36 @@ static int brcmf_setup_ifmodes(struct wiphy *wiphy, struct brcmf_if *ifp) c = 0; i = 0; - c0_limits = kcalloc(p2p ? 3 : 2, sizeof(*c0_limits), GFP_KERNEL); + if (p2p && rsdb) + c0_limits = kcalloc(4, sizeof(*c0_limits), GFP_KERNEL); + else if (p2p) + c0_limits = kcalloc(3, sizeof(*c0_limits), GFP_KERNEL); + else + c0_limits = kcalloc(2, sizeof(*c0_limits), GFP_KERNEL); if (!c0_limits) goto err; - c0_limits[i].max = 1; - c0_limits[i++].types = BIT(NL80211_IFTYPE_STATION); - if (p2p) { + if (p2p && rsdb) { + combo[c].num_different_channels = 2; + wiphy->interface_modes |= BIT(NL80211_IFTYPE_P2P_CLIENT) | + BIT(NL80211_IFTYPE_P2P_GO) | + BIT(NL80211_IFTYPE_P2P_DEVICE); + c0_limits[i].max = 1; + c0_limits[i++].types = BIT(NL80211_IFTYPE_STATION); + c0_limits[i].max = 1; + c0_limits[i++].types = BIT(NL80211_IFTYPE_P2P_DEVICE); + c0_limits[i].max = 2; + c0_limits[i++].types = BIT(NL80211_IFTYPE_P2P_CLIENT) | + BIT(NL80211_IFTYPE_P2P_GO); + c0_limits[i].max = 2; + c0_limits[i++].types = BIT(NL80211_IFTYPE_AP); + combo[c].max_interfaces = 4; + } else if (p2p) { if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MCHAN)) combo[c].num_different_channels = 2; else combo[c].num_different_channels = 1; + c0_limits[i].max = 1; + c0_limits[i++].types = BIT(NL80211_IFTYPE_STATION); wiphy->interface_modes |= BIT(NL80211_IFTYPE_P2P_CLIENT) | BIT(NL80211_IFTYPE_P2P_GO) | BIT(NL80211_IFTYPE_P2P_DEVICE); @@ -6515,16 +7062,26 @@ static int brcmf_setup_ifmodes(struct wiphy *wiphy, struct brcmf_if *ifp) c0_limits[i].max = 1; c0_limits[i++].types = BIT(NL80211_IFTYPE_P2P_CLIENT) | BIT(NL80211_IFTYPE_P2P_GO); + combo[c].max_interfaces = i; + } else if (rsdb) { + combo[c].num_different_channels = 2; + c0_limits[i].max = 1; + c0_limits[i++].types = BIT(NL80211_IFTYPE_STATION); + c0_limits[i].max = 2; + c0_limits[i++].types = BIT(NL80211_IFTYPE_AP); + combo[c].max_interfaces = 3; } else { combo[c].num_different_channels = 1; c0_limits[i].max = 1; + c0_limits[i++].types = BIT(NL80211_IFTYPE_STATION); + c0_limits[i].max = 1; c0_limits[i++].types = BIT(NL80211_IFTYPE_AP); + combo[c].max_interfaces = i; } - combo[c].max_interfaces = i; combo[c].n_limits = i; combo[c].limits = c0_limits; - if (p2p) { + if (p2p && !rsdb) { c++; i = 0; p2p_limits = kcalloc(4, sizeof(*p2p_limits), GFP_KERNEL); @@ -6587,6 +7144,7 @@ static void brcmf_wiphy_wowl_params(struct wiphy *wiphy, struct brcmf_if *ifp) struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); struct brcmf_pub *drvr = cfg->pub; struct wiphy_wowlan_support *wowl; + struct cfg80211_wowlan *brcmf_wowlan_config = NULL; wowl = kmemdup(&brcmf_wowlan_support, sizeof(brcmf_wowlan_support), GFP_KERNEL); @@ -6609,12 +7167,34 @@ static void brcmf_wiphy_wowl_params(struct wiphy *wiphy, struct brcmf_if *ifp) } wiphy->wowlan = wowl; + + /* wowlan_config structure report for kernels */ + brcmf_wowlan_config = kzalloc(sizeof(*brcmf_wowlan_config), + GFP_KERNEL); + if (brcmf_wowlan_config) { + brcmf_wowlan_config->any = false; + brcmf_wowlan_config->disconnect = true; + brcmf_wowlan_config->eap_identity_req = true; + brcmf_wowlan_config->four_way_handshake = true; + brcmf_wowlan_config->rfkill_release = false; + brcmf_wowlan_config->patterns = NULL; + brcmf_wowlan_config->n_patterns = 0; + brcmf_wowlan_config->tcp = NULL; + if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_WOWL_GTK)) + brcmf_wowlan_config->gtk_rekey_failure = true; + else + brcmf_wowlan_config->gtk_rekey_failure = false; + } else { + brcmf_err("Can not allocate memory for brcm_wowlan_config\n"); + } + wiphy->wowlan_config = brcmf_wowlan_config; #endif } static int brcmf_setup_wiphy(struct wiphy *wiphy, struct brcmf_if *ifp) { struct brcmf_pub *drvr = ifp->drvr; + struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); const struct ieee80211_iface_combination *combo; struct ieee80211_supported_band *band; u16 max_interfaces = 0; @@ -6672,6 +7252,16 @@ static int brcmf_setup_wiphy(struct wiphy *wiphy, struct brcmf_if *ifp) NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK); wiphy_ext_feature_set(wiphy, NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X); + if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_SAE)) + wiphy_ext_feature_set(wiphy, + NL80211_EXT_FEATURE_SAE_OFFLOAD); + } + if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_FWAUTH)) { + wiphy_ext_feature_set(wiphy, + NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK); + if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_SAE)) + wiphy_ext_feature_set(wiphy, + NL80211_EXT_FEATURE_SAE_OFFLOAD); } wiphy->mgmt_stypes = brcmf_txrx_stypes; wiphy->max_remain_on_channel_duration = 5000; @@ -6682,9 +7272,12 @@ static int brcmf_setup_wiphy(struct wiphy *wiphy, struct brcmf_if *ifp) /* vendor commands/events support */ wiphy->vendor_commands = brcmf_vendor_cmds; wiphy->n_vendor_commands = BRCMF_VNDR_CMDS_LAST - 1; + wiphy->vendor_events = brcmf_vendor_events; + wiphy->n_vendor_events = BRCMF_VNDR_EVTS_LAST; + brcmf_fweh_register(cfg->pub, BRCMF_E_PHY_TEMP, + brcmf_wiphy_phy_temp_evt_handler); - if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_WOWL)) - brcmf_wiphy_wowl_params(wiphy, ifp); + brcmf_wiphy_wowl_params(wiphy, ifp); err = brcmf_fil_cmd_data_get(ifp, BRCMF_C_GET_BANDLIST, &bandlist, sizeof(bandlist)); if (err) { @@ -6747,6 +7340,7 @@ static s32 brcmf_config_dongle(struct brcmf_cfg80211_info *cfg) struct wireless_dev *wdev; struct brcmf_if *ifp; s32 power_mode; + s32 eap_restrict; s32 err = 0; if (cfg->dongle_up) @@ -6761,7 +7355,7 @@ static s32 brcmf_config_dongle(struct brcmf_cfg80211_info *cfg) brcmf_dongle_scantime(ifp); - power_mode = cfg->pwr_save ? PM_FAST : PM_OFF; + power_mode = cfg->pwr_save ? ifp->drvr->settings->default_pm : PM_OFF; err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_PM, power_mode); if (err) goto default_conf_out; @@ -6771,6 +7365,14 @@ static s32 brcmf_config_dongle(struct brcmf_cfg80211_info *cfg) err = brcmf_dongle_roam(ifp); if (err) goto default_conf_out; + + eap_restrict = ifp->drvr->settings->eap_restrict; + if (eap_restrict) { + err = brcmf_fil_iovar_int_set(ifp, "eap_restrict", + eap_restrict); + if (err) + brcmf_info("eap_restrict error (%d)\n", err); + } err = brcmf_cfg80211_change_iface(wdev->wiphy, ndev, wdev->iftype, NULL); if (err) @@ -6807,7 +7409,7 @@ static s32 __brcmf_cfg80211_down(struct brcmf_if *ifp) * from AP to save power */ if (check_vif_up(ifp->vif)) { - brcmf_link_down(ifp->vif, WLAN_REASON_UNSPECIFIED); + brcmf_link_down(ifp->vif, WLAN_REASON_UNSPECIFIED, true); /* Make sure WPA_Supplicant receives all the event generated due to DISASSOC call to the fw to keep @@ -7051,6 +7653,8 @@ struct brcmf_cfg80211_info *brcmf_cfg80211_attach(struct brcmf_pub *drvr, cfg->wiphy = wiphy; cfg->pub = drvr; + cfg->pm_state = BRCMF_CFG80211_PM_STATE_RESUMED; + cfg->num_softap = 0; init_vif_event(&cfg->vif_event); INIT_LIST_HEAD(&cfg->vif_list); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h index 14d5bba..bd4ea5e 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h @@ -23,6 +23,23 @@ #define WL_ROAM_TRIGGER_LEVEL -75 #define WL_ROAM_DELTA 20 +/* WME Access Category Indices (ACIs) */ +#define AC_BE 0 /* Best Effort */ +#define AC_BK 1 /* Background */ +#define AC_VI 2 /* Video */ +#define AC_VO 3 /* Voice */ +#define EDCF_AC_COUNT 4 +#define MAX_8021D_PRIO 8 + +#define EDCF_ACI_MASK 0x60 +#define EDCF_ACI_SHIFT 5 +#define EDCF_ACM_MASK 0x10 +#define EDCF_ECWMIN_MASK 0x0f +#define EDCF_ECWMAX_SHIFT 4 +#define EDCF_AIFSN_MASK 0x0f +#define EDCF_AIFSN_MAX 15 +#define EDCF_ECWMAX_MASK 0xf0 + /* Keep BRCMF_ESCAN_BUF_SIZE below 64K (65536). Allocing over 64K can be * problematic on some systems and should be avoided. */ @@ -75,6 +92,15 @@ #define BRCMF_VIF_EVENT_TIMEOUT msecs_to_jiffies(1500) +#define BRCMF_PM_WAIT_MAXRETRY 100 + +/* cfg80211 wowlan definitions */ +#define WL_WOWLAN_MAX_PATTERNS 8 +#define WL_WOWLAN_MIN_PATTERN_LEN 1 +#define WL_WOWLAN_MAX_PATTERN_LEN 255 +#define WL_WOWLAN_PKT_FILTER_ID_FIRST 201 +#define WL_WOWLAN_PKT_FILTER_ID_LAST (WL_WOWLAN_PKT_FILTER_ID_FIRST + \ + WL_WOWLAN_MAX_PATTERNS - 1) /** * enum brcmf_scan_status - scan engine status * @@ -107,7 +133,21 @@ struct brcmf_cfg80211_security { enum brcmf_profile_fwsup { BRCMF_PROFILE_FWSUP_NONE, BRCMF_PROFILE_FWSUP_PSK, - BRCMF_PROFILE_FWSUP_1X + BRCMF_PROFILE_FWSUP_1X, + BRCMF_PROFILE_FWSUP_SAE +}; + +/** + * enum brcmf_profile_fwauth - firmware authenticator profile + * + * @BRCMF_PROFILE_FWAUTH_NONE: no firmware authenticator + * @BRCMF_PROFILE_FWAUTH_PSK: authenticator for WPA/WPA2-PSK + * @BRCMF_PROFILE_FWAUTH_PSK: authenticator for SAE + */ +enum brcmf_profile_fwauth { + BRCMF_PROFILE_FWAUTH_NONE, + BRCMF_PROFILE_FWAUTH_PSK, + BRCMF_PROFILE_FWAUTH_SAE }; /** @@ -122,6 +162,9 @@ struct brcmf_cfg80211_profile { struct brcmf_cfg80211_security sec; struct brcmf_wsec_key key[BRCMF_MAX_DEFAULT_KEYS]; enum brcmf_profile_fwsup use_fwsup; + u16 use_fwauth; + bool is_ft; + bool is_okc; }; /** @@ -145,25 +188,36 @@ enum brcmf_vif_status { BRCMF_VIF_STATUS_ASSOC_SUCCESS, }; +enum brcmf_cfg80211_pm_state { + BRCMF_CFG80211_PM_STATE_RESUMED, + BRCMF_CFG80211_PM_STATE_RESUMING, + BRCMF_CFG80211_PM_STATE_SUSPENDED, + BRCMF_CFG80211_PM_STATE_SUSPENDING, +}; + /** * struct vif_saved_ie - holds saved IEs for a virtual interface. * * @probe_req_ie: IE info for probe request. * @probe_res_ie: IE info for probe response. * @beacon_ie: IE info for beacon frame. + * @assoc_res_ie: IE info for association response frame. * @probe_req_ie_len: IE info length for probe request. * @probe_res_ie_len: IE info length for probe response. * @beacon_ie_len: IE info length for beacon frame. + * @assoc_res_ie_len: IE info length for association response frame. */ struct vif_saved_ie { u8 probe_req_ie[IE_MAX_LEN]; u8 probe_res_ie[IE_MAX_LEN]; u8 beacon_ie[IE_MAX_LEN]; u8 assoc_req_ie[IE_MAX_LEN]; + u8 assoc_res_ie[IE_MAX_LEN]; u32 probe_req_ie_len; u32 probe_res_ie_len; u32 beacon_ie_len; u32 assoc_req_ie_len; + u32 assoc_res_ie_len; }; /** @@ -203,6 +257,12 @@ struct brcmf_cfg80211_assoc_ielen_le { __le32 resp_len; }; +struct brcmf_cfg80211_edcf_acparam { + u8 ACI; + u8 ECW; + u16 TXOP; /* stored in network order (ls octet first) */ +}; + /* dongle escan state */ enum wl_escan_state { WL_ESCAN_STATE_IDLE, @@ -321,6 +381,9 @@ struct brcmf_cfg80211_info { struct brcmf_assoclist_le assoclist; struct brcmf_cfg80211_wowl wowl; struct brcmf_pno_info *pno; + u8 ac_priority[MAX_8021D_PRIO]; + u8 pm_state; + u8 num_softap; }; /** diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c index dd586a9..8285045 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c @@ -213,6 +213,24 @@ struct sbsocramregs { #define ARMCR4_BSZ_MASK 0x3f #define ARMCR4_BSZ_MULT 8192 +/* Minimum PMU resource mask for 43012C0 */ +#define CY_43012_PMU_MIN_RES_MASK 0xF8BFE77 + +/* PMU STATUS mask for 43012C0 */ +#define CY_43012_PMU_STATUS_MASK 0x1AC + +/* PMU CONTROL EXT mask for 43012C0 */ +#define CY_43012_PMU_CONTROL_EXT_MASK 0x11 + +/* PMU Watchdog Counter Tick value for 43012C0 */ +#define CY_43012_PMU_WATCHDOG_TICK_VAL 0x04 + +/* PMU Watchdog Counter Tick value for 4373 */ +#define CY_4373_PMU_WATCHDOG_TICK_VAL 0x04 + +/* Minimum PMU resource mask for 4373 */ +#define CY_4373_PMU_MIN_RES_MASK 0xFCAFF7F + struct brcmf_core_priv { struct brcmf_core pub; u32 wrapbase; @@ -433,11 +451,25 @@ static void brcmf_chip_ai_resetcore(struct brcmf_core_priv *core, u32 prereset, { struct brcmf_chip_priv *ci; int count; + struct brcmf_core *d11core2 = NULL; + struct brcmf_core_priv *d11priv2 = NULL; ci = core->chip; + /* special handle two D11 cores reset */ + if (core->pub.id == BCMA_CORE_80211) { + d11core2 = brcmf_chip_get_d11core(&ci->pub, 1); + if (d11core2) { + brcmf_dbg(INFO, "found two d11 cores, reset both\n"); + d11priv2 = container_of(d11core2, + struct brcmf_core_priv, pub); + } + } + /* must disable first to work for arbitrary current core state */ brcmf_chip_ai_coredisable(core, prereset, reset); + if (d11priv2) + brcmf_chip_ai_coredisable(d11priv2, prereset, reset); count = 0; while (ci->ops->read32(ci->ctx, core->wrapbase + BCMA_RESET_CTL) & @@ -449,9 +481,30 @@ static void brcmf_chip_ai_resetcore(struct brcmf_core_priv *core, u32 prereset, usleep_range(40, 60); } + if (d11priv2) { + count = 0; + while (ci->ops->read32(ci->ctx, + d11priv2->wrapbase + BCMA_RESET_CTL) & + BCMA_RESET_CTL_RESET) { + ci->ops->write32(ci->ctx, + d11priv2->wrapbase + BCMA_RESET_CTL, + 0); + count++; + if (count > 50) + break; + usleep_range(40, 60); + } + } + ci->ops->write32(ci->ctx, core->wrapbase + BCMA_IOCTL, postreset | BCMA_IOCTL_CLK); ci->ops->read32(ci->ctx, core->wrapbase + BCMA_IOCTL); + + if (d11priv2) { + ci->ops->write32(ci->ctx, d11priv2->wrapbase + BCMA_IOCTL, + postreset | BCMA_IOCTL_CLK); + ci->ops->read32(ci->ctx, d11priv2->wrapbase + BCMA_IOCTL); + } } char *brcmf_chip_name(u32 id, u32 rev, char *buf, uint len) @@ -689,6 +742,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci) return 0x200000; case CY_CC_4373_CHIP_ID: return 0x160000; + case CY_CC_89459_CHIP_ID: + return ((ci->pub.chiprev < 9) ? 0x180000 : 0x160000); default: brcmf_err("unknown chip: %s\n", ci->pub.name); break; @@ -1113,6 +1168,21 @@ void brcmf_chip_detach(struct brcmf_chip *pub) kfree(chip); } +struct brcmf_core *brcmf_chip_get_d11core(struct brcmf_chip *pub, u8 unit) +{ + struct brcmf_chip_priv *chip; + struct brcmf_core_priv *core; + + chip = container_of(pub, struct brcmf_chip_priv, pub); + list_for_each_entry(core, &chip->cores, list) { + if (core->pub.id == BCMA_CORE_80211) { + if (unit-- == 0) + return &core->pub; + } + } + return NULL; +} + struct brcmf_core *brcmf_chip_get_core(struct brcmf_chip *pub, u16 coreid) { struct brcmf_chip_priv *chip; @@ -1155,6 +1225,14 @@ struct brcmf_core *brcmf_chip_get_pmu(struct brcmf_chip *pub) return cc; } +struct brcmf_core *brcmf_chip_get_gci(struct brcmf_chip *pub) +{ + struct brcmf_core *gci; + + gci = brcmf_chip_get_core(pub, BCMA_CORE_GCI); + return gci; +} + bool brcmf_chip_iscoreup(struct brcmf_core *pub) { struct brcmf_core_priv *core; @@ -1357,10 +1435,12 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub) reg = chip->ops->read32(chip->ctx, addr); return reg != 0; case CY_CC_4373_CHIP_ID: + case CY_CC_89459_CHIP_ID: /* explicitly check SR engine enable bit */ addr = CORE_CC_REG(base, sr_control0); reg = chip->ops->read32(chip->ctx, addr); return (reg & CC_SR_CTL0_ENABLE_MASK) != 0; + case BRCM_CC_4359_CHIP_ID: case CY_CC_43012_CHIP_ID: addr = CORE_CC_REG(pmu->base, retention_ctl); reg = chip->ops->read32(chip->ctx, addr); @@ -1378,3 +1458,151 @@ bool brcmf_chip_sr_capable(struct brcmf_chip *pub) PMU_RCTL_LOGIC_DISABLE_MASK)) == 0; } } + +void brcmf_chip_reset_pmu_regs(struct brcmf_chip *pub) +{ + struct brcmf_chip_priv *chip; + u32 addr; + u32 base; + + brcmf_dbg(TRACE, "Enter\n"); + + chip = container_of(pub, struct brcmf_chip_priv, pub); + base = brcmf_chip_get_pmu(pub)->base; + + switch (pub->chip) { + case CY_CC_43012_CHIP_ID: + /* SW scratch */ + addr = CORE_CC_REG(base, swscratch); + chip->ops->write32(chip->ctx, addr, 0); + + /* PMU status */ + addr = CORE_CC_REG(base, pmustatus); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_STATUS_MASK); + + /* PMU control ext */ + addr = CORE_CC_REG(base, pmucontrol_ext); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_CONTROL_EXT_MASK); + break; + + default: + brcmf_err("Unsupported chip id\n"); + break; + } +} + +void brcmf_chip_set_default_min_res_mask(struct brcmf_chip *pub) +{ + struct brcmf_chip_priv *chip; + u32 addr; + u32 base; + + brcmf_dbg(TRACE, "Enter\n"); + + chip = container_of(pub, struct brcmf_chip_priv, pub); + base = brcmf_chip_get_pmu(pub)->base; + switch (pub->chip) { + case CY_CC_43012_CHIP_ID: + addr = CORE_CC_REG(base, min_res_mask); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_MIN_RES_MASK); + break; + + default: + brcmf_err("Unsupported chip id\n"); + break; + } +} + +void brcmf_chip_ulp_reset_lhl_regs(struct brcmf_chip *pub) +{ + struct brcmf_chip_priv *chip; + u32 base; + u32 addr; + + brcmf_dbg(TRACE, "Enter\n"); + + chip = container_of(pub, struct brcmf_chip_priv, pub); + base = brcmf_chip_get_gci(pub)->base; + + /* LHL Top Level Power Sequence Control */ + addr = CORE_GCI_REG(base, lhl_top_pwrseq_ctl_adr); + chip->ops->write32(chip->ctx, addr, 0); + + /* GPIO Interrupt Enable0 */ + addr = CORE_GCI_REG(base, gpio_int_en_port_adr[0]); + chip->ops->write32(chip->ctx, addr, 0); + + /* GPIO Interrupt Status0 */ + addr = CORE_GCI_REG(base, gpio_int_st_port_adr[0]); + chip->ops->write32(chip->ctx, addr, ~0); + + /* WL ARM Timer0 Interrupt Mask */ + addr = CORE_GCI_REG(base, lhl_wl_armtim0_intrp_adr); + chip->ops->write32(chip->ctx, addr, 0); + + /* WL ARM Timer0 Interrupt Status */ + addr = CORE_GCI_REG(base, lhl_wl_armtim0_st_adr); + chip->ops->write32(chip->ctx, addr, ~0); + + /* WL ARM Timer */ + addr = CORE_GCI_REG(base, lhl_wl_armtim0_adr); + chip->ops->write32(chip->ctx, addr, 0); + + /* WL MAC Timer0 Interrupt Mask */ + addr = CORE_GCI_REG(base, lhl_wl_mactim0_intrp_adr); + chip->ops->write32(chip->ctx, addr, 0); + + /* WL MAC Timer0 Interrupt Status */ + addr = CORE_GCI_REG(base, lhl_wl_mactim0_st_adr); + chip->ops->write32(chip->ctx, addr, ~0); + + /* WL MAC TimerInt0 */ + addr = CORE_GCI_REG(base, lhl_wl_mactim_int0_adr); + chip->ops->write32(chip->ctx, addr, 0x0); +} + +void brcmf_chip_reset_watchdog(struct brcmf_chip *pub) +{ + struct brcmf_chip_priv *chip; + u32 base; + u32 addr; + + brcmf_dbg(TRACE, "Enter\n"); + + chip = container_of(pub, struct brcmf_chip_priv, pub); + base = brcmf_chip_get_pmu(pub)->base; + + switch (pub->chip) { + case CY_CC_43012_CHIP_ID: + addr = CORE_CC_REG(base, min_res_mask); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_MIN_RES_MASK); + /* Watchdog res mask */ + addr = CORE_CC_REG(base, watchdog_res_mask); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_MIN_RES_MASK); + /* PMU watchdog */ + addr = CORE_CC_REG(base, pmuwatchdog); + chip->ops->write32(chip->ctx, addr, + CY_43012_PMU_WATCHDOG_TICK_VAL); + break; + case CY_CC_4373_CHIP_ID: + addr = CORE_CC_REG(base, min_res_mask); + chip->ops->write32(chip->ctx, addr, + CY_4373_PMU_MIN_RES_MASK); + addr = CORE_CC_REG(base, watchdog_res_mask); + chip->ops->write32(chip->ctx, addr, + CY_4373_PMU_MIN_RES_MASK); + addr = CORE_CC_REG(base, pmuwatchdog); + chip->ops->write32(chip->ctx, addr, + CY_4373_PMU_WATCHDOG_TICK_VAL); + mdelay(100); + break; + default: + break; + } +} + diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.h index 7b00f6a..216e554 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.h @@ -8,7 +8,10 @@ #include #define CORE_CC_REG(base, field) \ - (base + offsetof(struct chipcregs, field)) + ((base) + offsetof(struct chipcregs, field)) + +#define CORE_GCI_REG(base, field) \ + ((base) + offsetof(struct chipgciregs, field)) /** * struct brcmf_chip - chip level information. @@ -74,6 +77,7 @@ struct brcmf_chip *brcmf_chip_attach(void *ctx, const struct brcmf_buscore_ops *ops); void brcmf_chip_detach(struct brcmf_chip *chip); struct brcmf_core *brcmf_chip_get_core(struct brcmf_chip *chip, u16 coreid); +struct brcmf_core *brcmf_chip_get_d11core(struct brcmf_chip *pub, u8 unit); struct brcmf_core *brcmf_chip_get_chipcommon(struct brcmf_chip *chip); struct brcmf_core *brcmf_chip_get_pmu(struct brcmf_chip *pub); bool brcmf_chip_iscoreup(struct brcmf_core *core); @@ -84,5 +88,9 @@ void brcmf_chip_set_passive(struct brcmf_chip *ci); bool brcmf_chip_set_active(struct brcmf_chip *ci, u32 rstvec); bool brcmf_chip_sr_capable(struct brcmf_chip *pub); char *brcmf_chip_name(u32 chipid, u32 chiprev, char *buf, uint len); +void brcmf_chip_reset_watchdog(struct brcmf_chip *pub); +void brcmf_chip_ulp_reset_lhl_regs(struct brcmf_chip *pub); +void brcmf_chip_reset_pmu_regs(struct brcmf_chip *pub); +void brcmf_chip_set_default_min_res_mask(struct brcmf_chip *pub); #endif /* BRCMF_AXIDMP_H */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c index 1fc9cfc..22a4aa3 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c @@ -20,6 +20,9 @@ #include "of.h" #include "firmware.h" #include "chip.h" +#include "defs.h" +#include "fweh.h" +#include MODULE_AUTHOR("Broadcom Corporation"); MODULE_DESCRIPTION("Broadcom 802.11 wireless LAN fullmac driver."); @@ -67,6 +70,18 @@ static int brcmf_iapp_enable; module_param_named(iapp, brcmf_iapp_enable, int, 0); MODULE_PARM_DESC(iapp, "Enable partial support for the obsoleted Inter-Access Point Protocol"); +static int brcmf_eap_restrict; +module_param_named(eap_restrict, brcmf_eap_restrict, int, 0400); +MODULE_PARM_DESC(eap_restrict, "Block non-802.1X frames until auth finished"); + +static int brcmf_sdio_wq_highpri; +module_param_named(sdio_wq_highpri, brcmf_sdio_wq_highpri, int, 0); +MODULE_PARM_DESC(sdio_wq_highpri, "SDIO workqueue is set to high priority"); + +static int brcmf_max_pm; +module_param_named(max_pm, brcmf_max_pm, int, 0); +MODULE_PARM_DESC(max_pm, "Use max power management mode by default"); + #ifdef DEBUG /* always succeed brcmf_bus_started() */ static int brcmf_ignore_probe_fail; @@ -201,8 +216,10 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp) char *clmver; char *ptr; s32 err; + struct eventmsgs_ext *eventmask_msg = NULL; + u8 msglen; - /* retreive mac address */ + /* retrieve mac addresses */ err = brcmf_fil_iovar_data_get(ifp, "cur_etheraddr", ifp->mac_addr, sizeof(ifp->mac_addr)); if (err < 0) { @@ -292,6 +309,11 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp) brcmf_dbg(INFO, "CLM version = %s\n", clmver); } + /* set apsta */ + err = brcmf_fil_iovar_int_set(ifp, "apsta", 1); + if (err) + brcmf_info("failed setting apsta, %d\n", err); + /* set mpc */ err = brcmf_fil_iovar_int_set(ifp, "mpc", 1); if (err) { @@ -316,6 +338,41 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp) goto done; } + /* Enable event_msg_ext specific to 43012 chip */ + if (bus->chip == CY_CC_43012_CHIP_ID) { + /* Program event_msg_ext to support event larger than 128 */ + msglen = (roundup(BRCMF_E_LAST, NBBY) / NBBY) + + EVENTMSGS_EXT_STRUCT_SIZE; + /* Allocate buffer for eventmask_msg */ + eventmask_msg = kzalloc(msglen, GFP_KERNEL); + if (!eventmask_msg) { + err = -ENOMEM; + goto done; + } + + /* Read the current programmed event_msgs_ext */ + eventmask_msg->ver = EVENTMSGS_VER; + eventmask_msg->len = roundup(BRCMF_E_LAST, NBBY) / NBBY; + err = brcmf_fil_iovar_data_get(ifp, "event_msgs_ext", + eventmask_msg, + msglen); + + /* Enable ULP event */ + brcmf_dbg(EVENT, "enable event ULP\n"); + setbit(eventmask_msg->mask, BRCMF_E_ULP); + + /* Write updated Event mask */ + eventmask_msg->ver = EVENTMSGS_VER; + eventmask_msg->command = EVENTMSGS_SET_MASK; + eventmask_msg->len = (roundup(BRCMF_E_LAST, NBBY) / NBBY); + + err = brcmf_fil_iovar_data_set(ifp, "event_msgs_ext", + eventmask_msg, msglen); + if (err) { + brcmf_err("Set event_msgs_ext error (%d)\n", err); + goto done; + } + } /* Setup default scan channel time */ err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_SCAN_CHANNEL_TIME, BRCMF_DEFAULT_SCAN_CHANNEL_TIME); @@ -336,6 +393,18 @@ int brcmf_c_preinit_dcmds(struct brcmf_if *ifp) /* Enable tx beamforming, errors can be ignored (not supported) */ (void)brcmf_fil_iovar_int_set(ifp, "txbf", 1); + + /* add unicast packet filter */ + err = brcmf_pktfilter_add_remove(ifp->ndev, + BRCMF_UNICAST_FILTER_NUM, true); + if (err == -BRCMF_FW_UNSUPPORTED) { + /* FW not support can be ignored */ + err = 0; + goto done; + } else if (err) { + bphy_err(drvr, "Add unicast filter error (%d)\n", err); + } + done: return err; } @@ -407,12 +476,15 @@ struct brcmf_mp_device *brcmf_get_module_param(struct device *dev, if (!settings) return NULL; - /* start by using the module paramaters */ + /* start by using the module parameters */ settings->p2p_enable = !!brcmf_p2p_enable; settings->feature_disable = brcmf_feature_disable; settings->fcmode = brcmf_fcmode; settings->roamoff = !!brcmf_roamoff; settings->iapp = !!brcmf_iapp_enable; + settings->eap_restrict = !!brcmf_eap_restrict; + settings->sdio_wq_highpri = !!brcmf_sdio_wq_highpri; + settings->default_pm = !!brcmf_max_pm ? PM_MAX : PM_FAST; #ifdef DEBUG settings->ignore_probe_fail = !!brcmf_ignore_probe_fail; #endif @@ -492,7 +564,7 @@ static int __init brcmfmac_module_init(void) if (err == -ENODEV) brcmf_dbg(INFO, "No platform data available.\n"); - /* Initialize global module paramaters */ + /* Initialize global module parameters */ brcmf_mp_attach(); /* Continue the initialization by registering the different busses */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.h index 144cf45..c0bf586 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.h @@ -37,6 +37,9 @@ extern struct brcmf_mp_global_t brcmf_mp_global; * @feature_disable: Feature_disable bitmask. * @fcmode: FWS flow control. * @roamoff: Firmware roaming off? + * @eap_restrict: Not allow data tx/rx until 802.1X auth succeeds + * @sdio_wq_highpri: Tasks submitted to SDIO workqueue will run immediately. + * @default_pm: default power management (PM) mode. * @ignore_probe_fail: Ignore probe failure. * @country_codes: If available, pointer to struct for translating country codes * @bus: Bus specific platform data. Only SDIO at the mmoment. @@ -47,6 +50,9 @@ struct brcmf_mp_device { int fcmode; bool roamoff; bool iapp; + bool eap_restrict; + bool sdio_wq_highpri; + int default_pm; bool ignore_probe_fail; struct brcmfmac_pd_cc *country_codes; const char *board_type; @@ -72,4 +78,8 @@ static inline void brcmf_dmi_probe(struct brcmf_mp_device *settings, u32 chip, u32 chiprev) {} #endif +u8 brcmf_map_prio_to_prec(void *cfg, u8 prio); + +u8 brcmf_map_prio_to_aci(void *cfg, u8 prio); + #endif /* BRCMFMAC_COMMON_H */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c index 85cf964..fe083f8 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.c @@ -62,6 +62,14 @@ struct wlc_d11rxhdr { s8 rxpwr[4]; } __packed; +#define BRCMF_IF_STA_LIST_LOCK_INIT(ifp) spin_lock_init(&(ifp)->sta_list_lock) +#define BRCMF_IF_STA_LIST_LOCK(ifp, flags) \ + spin_lock_irqsave(&(ifp)->sta_list_lock, (flags)) +#define BRCMF_IF_STA_LIST_UNLOCK(ifp, flags) \ + spin_unlock_irqrestore(&(ifp)->sta_list_lock, (flags)) + +#define BRCMF_STA_NULL ((struct brcmf_sta *)NULL) + char *brcmf_ifname(struct brcmf_if *ifp) { if (!ifp) @@ -191,7 +199,6 @@ static void _brcmf_set_multicast_list(struct work_struct *work) if (err < 0) bphy_err(drvr, "Setting BRCMF_C_SET_PROMISC failed, %d\n", err); - brcmf_configure_arp_nd_offload(ifp, !cmd_value); } #if IS_ENABLED(CONFIG_IPV6) @@ -352,6 +359,9 @@ static netdev_tx_t brcmf_netdev_start_xmit(struct sk_buff *skb, if ((skb->priority == 0) || (skb->priority > 7)) skb->priority = cfg80211_classify8021d(skb, NULL); + /* set pacing shift for packet aggregation */ + sk_pacing_shift_update(skb->sk, 8); + ret = brcmf_proto_tx_queue_data(drvr, ifp->ifidx, skb); if (ret < 0) brcmf_txfinalize(ifp, skb, false); @@ -536,6 +546,11 @@ void brcmf_txfinalize(struct brcmf_if *ifp, struct sk_buff *txp, bool success) struct ethhdr *eh; u16 type; + if (!ifp) { + brcmu_pkt_buf_free_skb(txp); + return; + } + eh = (struct ethhdr *)(txp->data); type = ntohs(eh->h_proto); @@ -579,9 +594,6 @@ static int brcmf_netdev_stop(struct net_device *ndev) brcmf_cfg80211_down(ndev); - if (ifp->drvr->bus_if->state == BRCMF_BUS_UP) - brcmf_fil_iovar_data_set(ifp, "arp_hostip_clear", NULL, 0); - brcmf_net_setcarrier(ifp, false); return 0; @@ -817,7 +829,9 @@ struct brcmf_if *brcmf_add_if(struct brcmf_pub *drvr, s32 bsscfgidx, s32 ifidx, init_waitqueue_head(&ifp->pend_8021x_wait); spin_lock_init(&ifp->netif_stop_lock); - + BRCMF_IF_STA_LIST_LOCK_INIT(ifp); + /* Initialize STA info list */ + INIT_LIST_HEAD(&ifp->sta_list); if (mac_addr != NULL) memcpy(ifp->mac_addr, mac_addr, ETH_ALEN); @@ -1049,6 +1063,15 @@ static int brcmf_inet6addr_changed(struct notifier_block *nb, } #endif + +int brcmf_fwlog_attach(struct device *dev) +{ + struct brcmf_bus *bus_if = dev_get_drvdata(dev); + struct brcmf_pub *drvr = bus_if->drvr; + + return brcmf_debug_fwlog_init(drvr); +} + static int brcmf_revinfo_read(struct seq_file *s, void *data) { struct brcmf_bus *bus_if = dev_get_drvdata(s->private); @@ -1238,7 +1261,7 @@ int brcmf_alloc(struct device *dev, struct brcmf_mp_device *settings) return 0; } -int brcmf_attach(struct device *dev) +int brcmf_attach(struct device *dev, bool start_bus) { struct brcmf_bus *bus_if = dev_get_drvdata(dev); struct brcmf_pub *drvr = bus_if->drvr; @@ -1269,10 +1292,13 @@ int brcmf_attach(struct device *dev) /* attach firmware event handler */ brcmf_fweh_attach(drvr); - ret = brcmf_bus_started(drvr, drvr->ops); - if (ret != 0) { - bphy_err(drvr, "dongle is not responding: err=%d\n", ret); - goto fail; + if (start_bus) { + ret = brcmf_bus_started(drvr, drvr->ops); + if (ret != 0) { + bphy_err(drvr, "dongle is not responding: err=%d\n", + ret); + goto fail; + } } return 0; @@ -1405,8 +1431,10 @@ int brcmf_netdev_wait_pend8021x(struct brcmf_if *ifp) !brcmf_get_pend_8021x_cnt(ifp), MAX_WAIT_FOR_8021X_TX); - if (!err) + if (!err) { bphy_err(drvr, "Timed out waiting for no pending 802.1x packets\n"); + atomic_set(&ifp->pend_8021x_cnt, 0); + } return !err; } @@ -1475,3 +1503,268 @@ void __exit brcmf_core_exit(void) #endif } +int +brcmf_pktfilter_add_remove(struct net_device *ndev, int filter_num, bool add) +{ + struct brcmf_if *ifp = netdev_priv(ndev); + struct brcmf_pub *drvr = ifp->drvr; + struct brcmf_pkt_filter_le *pkt_filter; + int filter_fixed_len = offsetof(struct brcmf_pkt_filter_le, u); + int pattern_fixed_len = offsetof(struct brcmf_pkt_filter_pattern_le, + mask_and_pattern); + u16 mask_and_pattern[MAX_PKTFILTER_PATTERN_SIZE]; + int buflen = 0; + int ret = 0; + + brcmf_dbg(INFO, "%s packet filter number %d\n", + (add ? "add" : "remove"), filter_num); + + pkt_filter = kzalloc(sizeof(*pkt_filter) + + (MAX_PKTFILTER_PATTERN_SIZE * 2), GFP_ATOMIC); + if (!pkt_filter) + return -ENOMEM; + + switch (filter_num) { + case BRCMF_UNICAST_FILTER_NUM: + pkt_filter->id = 100; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 1; + mask_and_pattern[0] = 0x0001; + break; + case BRCMF_BROADCAST_FILTER_NUM: + //filter_pattern = "101 0 0 0 0xFFFFFFFFFFFF 0xFFFFFFFFFFFF"; + pkt_filter->id = 101; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 6; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0xFFFF; + mask_and_pattern[2] = 0xFFFF; + mask_and_pattern[3] = 0xFFFF; + mask_and_pattern[4] = 0xFFFF; + mask_and_pattern[5] = 0xFFFF; + break; + case BRCMF_MULTICAST4_FILTER_NUM: + //filter_pattern = "102 0 0 0 0xFFFFFF 0x01005E"; + pkt_filter->id = 102; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 3; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0x01FF; + mask_and_pattern[2] = 0x5E00; + break; + case BRCMF_MULTICAST6_FILTER_NUM: + //filter_pattern = "103 0 0 0 0xFFFF 0x3333"; + pkt_filter->id = 103; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 2; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0x3333; + break; + case BRCMF_MDNS_FILTER_NUM: + //filter_pattern = "104 0 0 0 0xFFFFFFFFFFFF 0x01005E0000FB"; + pkt_filter->id = 104; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 6; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0xFFFF; + mask_and_pattern[2] = 0xFFFF; + mask_and_pattern[3] = 0x0001; + mask_and_pattern[4] = 0x005E; + mask_and_pattern[5] = 0xFB00; + break; + case BRCMF_ARP_FILTER_NUM: + //filter_pattern = "105 0 0 12 0xFFFF 0x0806"; + pkt_filter->id = 105; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 12; + pkt_filter->u.pattern.size_bytes = 2; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0x0608; + break; + case BRCMF_BROADCAST_ARP_FILTER_NUM: + //filter_pattern = "106 0 0 0 + //0xFFFFFFFFFFFF0000000000000806 + //0xFFFFFFFFFFFF0000000000000806"; + pkt_filter->id = 106; + pkt_filter->type = 0; + pkt_filter->negate_match = 0; + pkt_filter->u.pattern.offset = 0; + pkt_filter->u.pattern.size_bytes = 14; + mask_and_pattern[0] = 0xFFFF; + mask_and_pattern[1] = 0xFFFF; + mask_and_pattern[2] = 0xFFFF; + mask_and_pattern[3] = 0x0000; + mask_and_pattern[4] = 0x0000; + mask_and_pattern[5] = 0x0000; + mask_and_pattern[6] = 0x0608; + mask_and_pattern[7] = 0xFFFF; + mask_and_pattern[8] = 0xFFFF; + mask_and_pattern[9] = 0xFFFF; + mask_and_pattern[10] = 0x0000; + mask_and_pattern[11] = 0x0000; + mask_and_pattern[12] = 0x0000; + mask_and_pattern[13] = 0x0608; + break; + default: + ret = -EINVAL; + goto failed; + } + memcpy(pkt_filter->u.pattern.mask_and_pattern, mask_and_pattern, + pkt_filter->u.pattern.size_bytes * 2); + buflen = filter_fixed_len + pattern_fixed_len + + pkt_filter->u.pattern.size_bytes * 2; + + if (add) { + /* Add filter */ + ifp->fwil_fwerr = true; + ret = brcmf_fil_iovar_data_set(ifp, "pkt_filter_add", + pkt_filter, buflen); + ifp->fwil_fwerr = false; + if (ret) + goto failed; + drvr->pkt_filter[filter_num].id = pkt_filter->id; + drvr->pkt_filter[filter_num].enable = 0; + + } else { + /* Delete filter */ + ret = brcmf_fil_iovar_int_set(ifp, "pkt_filter_delete", + pkt_filter->id); + if (ret == -ENOENT) + ret = 0; + if (ret) + goto failed; + + drvr->pkt_filter[filter_num].id = 0; + drvr->pkt_filter[filter_num].enable = 0; + } +failed: + if (ret) + brcmf_err("%s packet filter failed, ret=%d\n", + (add ? "add" : "remove"), ret); + + kfree(pkt_filter); + return ret; +} + +int brcmf_pktfilter_enable(struct net_device *ndev, bool enable) +{ + struct brcmf_if *ifp = netdev_priv(ndev); + struct brcmf_pub *drvr = ifp->drvr; + int ret = 0; + int idx = 0; + + for (idx = 0; idx < MAX_PKT_FILTER_COUNT; ++idx) { + if (drvr->pkt_filter[idx].id != 0) { + drvr->pkt_filter[idx].enable = enable; + ret = brcmf_fil_iovar_data_set(ifp, "pkt_filter_enable", + &drvr->pkt_filter[idx], + sizeof(struct brcmf_pkt_filter_enable_le)); + if (ret) { + brcmf_err("%s packet filter id(%d) failed, ret=%d\n", + (enable ? "enable" : "disable"), + drvr->pkt_filter[idx].id, ret); + } + } + } + return ret; +} + +/** Find STA with MAC address ea in an interface's STA list. */ +struct brcmf_sta * +brcmf_find_sta(struct brcmf_if *ifp, const u8 *ea) +{ + struct brcmf_sta *sta; + unsigned long flags; + + BRCMF_IF_STA_LIST_LOCK(ifp, flags); + list_for_each_entry(sta, &ifp->sta_list, list) { + if (!memcmp(sta->ea.octet, ea, ETH_ALEN)) { + brcmf_dbg(INFO, "Found STA: 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x into sta list\n", + sta->ea.octet[0], sta->ea.octet[1], + sta->ea.octet[2], sta->ea.octet[3], + sta->ea.octet[4], sta->ea.octet[5]); + BRCMF_IF_STA_LIST_UNLOCK(ifp, flags); + return sta; + } + } + BRCMF_IF_STA_LIST_UNLOCK(ifp, flags); + + return BRCMF_STA_NULL; +} + +/** Add STA into the interface's STA list. */ +struct brcmf_sta * +brcmf_add_sta(struct brcmf_if *ifp, const u8 *ea) +{ + struct brcmf_sta *sta; + unsigned long flags; + + sta = kzalloc(sizeof(*sta), GFP_KERNEL); + if (sta == BRCMF_STA_NULL) { + brcmf_err("Alloc failed\n"); + return BRCMF_STA_NULL; + } + memcpy(sta->ea.octet, ea, ETH_ALEN); + brcmf_dbg(INFO, "Add STA: 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x into sta list\n", + sta->ea.octet[0], sta->ea.octet[1], + sta->ea.octet[2], sta->ea.octet[3], + sta->ea.octet[4], sta->ea.octet[5]); + + /* link the sta and the dhd interface */ + sta->ifp = ifp; + INIT_LIST_HEAD(&sta->list); + + BRCMF_IF_STA_LIST_LOCK(ifp, flags); + + list_add_tail(&sta->list, &ifp->sta_list); + + BRCMF_IF_STA_LIST_UNLOCK(ifp, flags); + return sta; +} + +/** Delete STA from the interface's STA list. */ +void +brcmf_del_sta(struct brcmf_if *ifp, const u8 *ea) +{ + struct brcmf_sta *sta, *next; + unsigned long flags; + + BRCMF_IF_STA_LIST_LOCK(ifp, flags); + list_for_each_entry_safe(sta, next, &ifp->sta_list, list) { + if (!memcmp(sta->ea.octet, ea, ETH_ALEN)) { + brcmf_dbg(INFO, "del STA: 0x%x 0x%x 0x%x 0x%x 0x%x 0x%x from sta list\n", + ea[0], ea[1], ea[2], ea[3], + ea[4], ea[5]); + list_del(&sta->list); + kfree(sta); + } + } + + BRCMF_IF_STA_LIST_UNLOCK(ifp, flags); +} + +/** Add STA if it doesn't exist. Not reentrant. */ +struct brcmf_sta* +brcmf_findadd_sta(struct brcmf_if *ifp, const u8 *ea) +{ + struct brcmf_sta *sta = NULL; + + sta = brcmf_find_sta(ifp, ea); + + if (!sta) { + /* Add entry */ + sta = brcmf_add_sta(ifp, ea); + } + return sta; +} diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h index 6699637..29c931b 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/core.h @@ -12,6 +12,7 @@ #include #include "fweh.h" +#include "fwil_types.h" #define TOE_TX_CSUM_OL 0x00000001 #define TOE_RX_CSUM_OL 0x00000002 @@ -136,6 +137,8 @@ struct brcmf_pub { struct work_struct bus_reset; u8 clmver[BRCMF_DCMD_SMLEN]; + struct brcmf_pkt_filter_enable_le pkt_filter[MAX_PKT_FILTER_COUNT]; + }; /* forward declarations */ @@ -185,6 +188,7 @@ struct brcmf_if { struct brcmf_fws_mac_descriptor *fws_desc; int ifidx; s32 bsscfgidx; + bool isap; u8 mac_addr[ETH_ALEN]; u8 netif_stop; spinlock_t netif_stop_lock; @@ -193,6 +197,20 @@ struct brcmf_if { struct in6_addr ipv6_addr_tbl[NDOL_MAX_ENTRIES]; u8 ipv6addr_idx; bool fwil_fwerr; + struct list_head sta_list; /* sll of associated stations */ + spinlock_t sta_list_lock; + bool fmac_pkt_fwd_en; +}; + +struct ether_addr { + u8 octet[ETH_ALEN]; +}; + +/** Per STA params. A list of dhd_sta objects are managed in dhd_if */ +struct brcmf_sta { + void *ifp; /* associated brcm_if */ + struct ether_addr ea; /* stations ethernet mac address */ + struct list_head list; /* link into brcmf_if::sta_list */ }; int brcmf_netdev_wait_pend8021x(struct brcmf_if *ifp); @@ -213,5 +231,10 @@ void brcmf_netif_mon_rx(struct brcmf_if *ifp, struct sk_buff *skb); void brcmf_net_setcarrier(struct brcmf_if *ifp, bool on); int __init brcmf_core_init(void); void __exit brcmf_core_exit(void); - +int brcmf_pktfilter_add_remove(struct net_device *ndev, int filter_num, + bool add); +int brcmf_pktfilter_enable(struct net_device *ndev, bool enable); +void brcmf_del_sta(struct brcmf_if *ifp, const u8 *ea); +struct brcmf_sta *brcmf_find_sta(struct brcmf_if *ifp, const u8 *ea); +struct brcmf_sta *brcmf_findadd_sta(struct brcmf_if *ifp, const u8 *ea); #endif /* BRCMFMAC_CORE_H */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c index 120515f..26efe50 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c @@ -14,6 +14,82 @@ #include "fweh.h" #include "debug.h" +static int +brcmf_debug_msgtrace_seqchk(u32 *prev, u32 cur) +{ + if ((cur == 0 && *prev == 0xFFFFFFFF) || ((cur - *prev) == 1)) { + goto done; + } else if (cur == *prev) { + brcmf_dbg(FWCON, "duplicate trace\n"); + return -1; + } else if (cur > *prev) { + brcmf_dbg(FWCON, "lost %d packets\n", cur - *prev); + } else { + brcmf_dbg(FWCON, "seq out of order, host %d, dongle %d\n", + *prev, cur); + } +done: + *prev = cur; + return 0; +} + +static int +brcmf_debug_msg_parser(void *event_data) +{ + int err = 0; + struct msgtrace_hdr *hdr; + char *data, *s; + static u32 seqnum_prev; + + hdr = (struct msgtrace_hdr *)event_data; + data = (char *)event_data + MSGTRACE_HDRLEN; + + /* There are 2 bytes available at the end of data */ + data[ntohs(hdr->len)] = '\0'; + + if (ntohl(hdr->discarded_bytes) || ntohl(hdr->discarded_printf)) { + brcmf_dbg(FWCON, "Discarded_bytes %d discarded_printf %d\n", + ntohl(hdr->discarded_bytes), + ntohl(hdr->discarded_printf)); + } + + err = brcmf_debug_msgtrace_seqchk(&seqnum_prev, ntohl(hdr->seqnum)); + if (err) + return err; + + while (*data != '\0' && (s = strstr(data, "\n")) != NULL) { + *s = '\0'; + brcmf_dbg(FWCON, "CONSOLE: %s\n", data); + data = s + 1; + } + if (*data) + brcmf_dbg(FWCON, "CONSOLE: %s", data); + + return err; +} + +static int +brcmf_debug_trace_parser(struct brcmf_if *ifp, + const struct brcmf_event_msg *evtmsg, + void *event_data) +{ + int err = 0; + struct msgtrace_hdr *hdr; + + hdr = (struct msgtrace_hdr *)event_data; + if (hdr->version != MSGTRACE_VERSION) { + brcmf_dbg(FWCON, "trace version mismatch host %d dngl %d\n", + MSGTRACE_VERSION, hdr->version); + err = -EPROTO; + return err; + } + + if (hdr->trace_type == MSGTRACE_HDR_TYPE_MSG) + err = brcmf_debug_msg_parser(event_data); + + return err; +} + int brcmf_debug_create_memdump(struct brcmf_bus *bus, const void *data, size_t len) { @@ -42,6 +118,13 @@ int brcmf_debug_create_memdump(struct brcmf_bus *bus, const void *data, return 0; } + +int brcmf_debug_fwlog_init(struct brcmf_pub *drvr) +{ + return brcmf_fweh_register(drvr, BRCMF_E_TRACE, + brcmf_debug_trace_parser); +} + struct dentry *brcmf_debugfs_get_devdir(struct brcmf_pub *drvr) { return drvr->wiphy->debugfsdir; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.h index 9b221b5..f67f54c 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.h @@ -29,6 +29,7 @@ #define BRCMF_MSGBUF_VAL 0x00040000 #define BRCMF_PCIE_VAL 0x00080000 #define BRCMF_FWCON_VAL 0x00100000 +#define BRCMF_ULP_VAL 0x00200000 /* set default print format */ #undef pr_fmt @@ -103,6 +104,10 @@ do { \ #endif /* defined(DEBUG) || defined(CONFIG_BRCM_TRACING) */ +#define MSGTRACE_VERSION 1 +#define MSGTRACE_HDR_TYPE_MSG 0 +#define MSGTRACE_HDR_TYPE_LOG 1 + #define brcmf_dbg_hex_dump(test, data, len, fmt, ...) \ do { \ trace_brcmf_hexdump((void *)data, len); \ @@ -120,6 +125,7 @@ int brcmf_debugfs_add_entry(struct brcmf_pub *drvr, const char *fn, int (*read_fn)(struct seq_file *seq, void *data)); int brcmf_debug_create_memdump(struct brcmf_bus *bus, const void *data, size_t len); +int brcmf_debug_fwlog_init(struct brcmf_pub *drvr); #else static inline struct dentry *brcmf_debugfs_get_devdir(struct brcmf_pub *drvr) { @@ -137,6 +143,25 @@ int brcmf_debug_create_memdump(struct brcmf_bus *bus, const void *data, { return 0; } + +static inline +int brcmf_debug_fwlog_init(struct brcmf_pub *drvr) +{ + return 0; +} #endif +/* Message trace header */ +struct msgtrace_hdr { + u8 version; + u8 trace_type; + u16 len; /* Len of the trace */ + u32 seqnum; /* Sequence number of message */ + /* Number of discarded bytes because of trace overflow */ + u32 discarded_bytes; + /* Number of discarded printf because of trace overflow */ + u32 discarded_printf; +}; + +#define MSGTRACE_HDRLEN sizeof(struct msgtrace_hdr) #endif /* BRCMFMAC_DEBUG_H */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c index 31c9184..52b2ce6 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.c @@ -16,7 +16,6 @@ #include "feature.h" #include "common.h" -#define BRCMF_FW_UNSUPPORTED 23 /* * expand feature list to array of feature strings. @@ -39,7 +38,9 @@ static const struct brcmf_feat_fwcap brcmf_fwcap_map[] = { { BRCMF_FEAT_P2P, "p2p" }, { BRCMF_FEAT_MONITOR, "monitor" }, { BRCMF_FEAT_MONITOR_FMT_RADIOTAP, "rtap" }, - { BRCMF_FEAT_DOT11H, "802.11h" } + { BRCMF_FEAT_DOT11H, "802.11h" }, + { BRCMF_FEAT_SAE, "sae" }, + { BRCMF_FEAT_FWAUTH, "idauth" }, }; #ifdef DEBUG @@ -283,14 +284,13 @@ void brcmf_feat_attach(struct brcmf_pub *drvr) if (!err) ifp->drvr->feat_flags |= BIT(BRCMF_FEAT_SCAN_RANDOM_MAC); - brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_FWSUP, "sup_wpa"); - if (drvr->settings->feature_disable) { brcmf_dbg(INFO, "Features: 0x%02x, disable: 0x%02x\n", ifp->drvr->feat_flags, drvr->settings->feature_disable); ifp->drvr->feat_flags &= ~drvr->settings->feature_disable; } + brcmf_feat_iovar_int_get(ifp, BRCMF_FEAT_FWSUP, "sup_wpa"); brcmf_feat_firmware_overrides(drvr); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h index 736a817..56d991c 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/feature.h @@ -26,6 +26,8 @@ * MONITOR_FMT_RADIOTAP: firmware provides monitor packets with radiotap header * MONITOR_FMT_HW_RX_HDR: firmware provides monitor packets with hw/ucode header * DOT11H: firmware supports 802.11h + * SAE: simultaneous authentication of equals + * FWAUTH: Firmware authenticator */ #define BRCMF_FEAT_LIST \ BRCMF_FEAT_DEF(MBSS) \ @@ -45,7 +47,9 @@ BRCMF_FEAT_DEF(MONITOR) \ BRCMF_FEAT_DEF(MONITOR_FMT_RADIOTAP) \ BRCMF_FEAT_DEF(MONITOR_FMT_HW_RX_HDR) \ - BRCMF_FEAT_DEF(DOT11H) + BRCMF_FEAT_DEF(DOT11H) \ + BRCMF_FEAT_DEF(SAE) \ + BRCMF_FEAT_DEF(FWAUTH) /* * Quirks: diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/flowring.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/flowring.c index 8e9d067..e1127d7 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/flowring.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/flowring.c @@ -26,10 +26,10 @@ #define BRCMF_FLOWRING_HASH_STA(fifo, ifidx) (fifo + ifidx * 16) static const u8 brcmf_flowring_prio2fifo[] = { - 1, - 0, 0, 1, + 1, + 0, 2, 2, 3, @@ -419,7 +419,6 @@ void brcmf_flowring_configure_addr_mode(struct brcmf_flowring *flow, int ifidx, flowid = flow->hash[i].flowid; if (flow->rings[flowid]->status != RING_OPEN) continue; - flow->rings[flowid]->status = RING_CLOSING; brcmf_msgbuf_delete_flowring(drvr, flowid); } } @@ -458,10 +457,8 @@ void brcmf_flowring_delete_peer(struct brcmf_flowring *flow, int ifidx, if ((sta || (memcmp(hash[i].mac, peer, ETH_ALEN) == 0)) && (hash[i].ifidx == ifidx)) { flowid = flow->hash[i].flowid; - if (flow->rings[flowid]->status == RING_OPEN) { - flow->rings[flowid]->status = RING_CLOSING; + if (flow->rings[flowid]->status == RING_OPEN) brcmf_msgbuf_delete_flowring(drvr, flowid); - } } } diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.h index a82f51b..e740c2f 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fweh.h @@ -90,7 +90,9 @@ struct brcmf_cfg80211_info; BRCMF_ENUM_DEF(FIFO_CREDIT_MAP, 74) \ BRCMF_ENUM_DEF(ACTION_FRAME_RX, 75) \ BRCMF_ENUM_DEF(TDLS_PEER_EVENT, 92) \ - BRCMF_ENUM_DEF(BCMC_CREDIT_SUPPORT, 127) + BRCMF_ENUM_DEF(PHY_TEMP, 111) \ + BRCMF_ENUM_DEF(BCMC_CREDIT_SUPPORT, 127) \ + BRCMF_ENUM_DEF(ULP, 146) #define BRCMF_ENUM_DEF(id, val) \ BRCMF_E_##id = (val), @@ -102,7 +104,7 @@ enum brcmf_fweh_event_code { * minimum length check in device firmware so it is * hard-coded here. */ - BRCMF_E_LAST = 139 + BRCMF_E_LAST = 147 }; #undef BRCMF_ENUM_DEF @@ -283,6 +285,28 @@ struct brcmf_if_event { u8 role; }; +enum event_msgs_ext_command { + EVENTMSGS_NONE = 0, + EVENTMSGS_SET_BIT = 1, + EVENTMSGS_RESET_BIT = 2, + EVENTMSGS_SET_MASK = 3 +}; + +#define EVENTMSGS_VER 1 +#define EVENTMSGS_EXT_STRUCT_SIZE offsetof(struct eventmsgs_ext, mask[0]) + +/* len- for SET it would be mask size from the application to the firmware */ +/* for GET it would be actual firmware mask size */ +/* maxgetsize - is only used for GET. indicate max mask size that the */ +/* application can read from the firmware */ +struct eventmsgs_ext { + u8 ver; + u8 command; + u8 len; + u8 maxgetsize; + u8 mask[1]; +}; + typedef int (*brcmf_fweh_handler_t)(struct brcmf_if *ifp, const struct brcmf_event_msg *evtmsg, void *data); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h index 0ff6f52..f2e00a3 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.h @@ -77,6 +77,8 @@ #define BRCMF_C_SET_VAR 263 #define BRCMF_C_SET_WSEC_PMK 268 +#define BRCMF_FW_UNSUPPORTED 23 + s32 brcmf_fil_cmd_data_set(struct brcmf_if *ifp, u32 cmd, void *data, u32 len); s32 brcmf_fil_cmd_data_get(struct brcmf_if *ifp, u32 cmd, void *data, u32 len); s32 brcmf_fil_cmd_int_set(struct brcmf_if *ifp, u32 cmd, u32 data); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h index ce18433..b7c16dc 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil_types.h @@ -61,6 +61,8 @@ #define BRCMF_WSEC_MAX_PSK_LEN 32 #define BRCMF_WSEC_PASSPHRASE BIT(0) +#define BRCMF_WSEC_MAX_SAE_PASSWORD_LEN 128 + /* primary (ie tx) key */ #define BRCMF_PRIMARY_KEY (1 << 1) #define DOT11_BSSTYPE_ANY 2 @@ -133,9 +135,22 @@ /* Link Down indication in WoWL mode: */ #define BRCMF_WOWL_LINKDOWN (1 << 31) -#define BRCMF_WOWL_MAXPATTERNS 8 +#define BRCMF_WOWL_MAXPATTERNS 16 #define BRCMF_WOWL_MAXPATTERNSIZE 128 +enum { + BRCMF_UNICAST_FILTER_NUM = 0, + BRCMF_BROADCAST_FILTER_NUM, + BRCMF_MULTICAST4_FILTER_NUM, + BRCMF_MULTICAST6_FILTER_NUM, + BRCMF_MDNS_FILTER_NUM, + BRCMF_ARP_FILTER_NUM, + BRCMF_BROADCAST_ARP_FILTER_NUM, + MAX_PKT_FILTER_COUNT +}; + +#define MAX_PKTFILTER_PATTERN_SIZE 16 + #define BRCMF_COUNTRY_BUF_SZ 4 #define BRCMF_ANT_MAX 4 @@ -518,6 +533,17 @@ struct brcmf_wsec_pmk_le { u8 key[2 * BRCMF_WSEC_MAX_PSK_LEN + 1]; }; +/** + * struct brcmf_wsec_sae_pwd_le - firmware SAE password material. + * + * @key_len: number of octets in key materials. + * @key: SAE password material. + */ +struct brcmf_wsec_sae_pwd_le { + __le16 key_len; + u8 key[BRCMF_WSEC_MAX_SAE_PASSWORD_LEN]; +}; + /* Used to get specific STA parameters */ struct brcmf_scb_val_le { __le32 val; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c index eadc644..2357535 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c @@ -311,28 +311,6 @@ struct brcmf_skbuff_cb { /* How long to defer borrowing in jiffies */ #define BRCMF_FWS_BORROW_DEFER_PERIOD (HZ / 10) -/** - * enum brcmf_fws_fifo - fifo indices used by dongle firmware. - * - * @BRCMF_FWS_FIFO_FIRST: first fifo, ie. background. - * @BRCMF_FWS_FIFO_AC_BK: fifo for background traffic. - * @BRCMF_FWS_FIFO_AC_BE: fifo for best-effort traffic. - * @BRCMF_FWS_FIFO_AC_VI: fifo for video traffic. - * @BRCMF_FWS_FIFO_AC_VO: fifo for voice traffic. - * @BRCMF_FWS_FIFO_BCMC: fifo for broadcast/multicast (AP only). - * @BRCMF_FWS_FIFO_ATIM: fifo for ATIM (AP only). - * @BRCMF_FWS_FIFO_COUNT: number of fifos. - */ -enum brcmf_fws_fifo { - BRCMF_FWS_FIFO_FIRST, - BRCMF_FWS_FIFO_AC_BK = BRCMF_FWS_FIFO_FIRST, - BRCMF_FWS_FIFO_AC_BE, - BRCMF_FWS_FIFO_AC_VI, - BRCMF_FWS_FIFO_AC_VO, - BRCMF_FWS_FIFO_BCMC, - BRCMF_FWS_FIFO_ATIM, - BRCMF_FWS_FIFO_COUNT -}; /** * enum brcmf_fws_txstatus - txstatus flag values. @@ -345,6 +323,10 @@ enum brcmf_fws_fifo { * firmware suppress the packet as device is already in PS mode. * @BRCMF_FWS_TXSTATUS_FW_TOSSED: * firmware tossed the packet. + * @BRCMF_FWS_TXSTATUS_FW_DISCARD_NOACK: + * firmware tossed the packet after retries. + * @BRCMF_FWS_TXSTATUS_FW_SUPPRESS_ACKED: + * firmware wrongly reported suppressed previously, now fixing to acked. * @BRCMF_FWS_TXSTATUS_HOST_TOSSED: * host tossed the packet. */ @@ -353,6 +335,8 @@ enum brcmf_fws_txstatus { BRCMF_FWS_TXSTATUS_CORE_SUPPRESS, BRCMF_FWS_TXSTATUS_FW_PS_SUPPRESS, BRCMF_FWS_TXSTATUS_FW_TOSSED, + BRCMF_FWS_TXSTATUS_FW_DISCARD_NOACK, + BRCMF_FWS_TXSTATUS_FW_SUPPRESS_ACKED, BRCMF_FWS_TXSTATUS_HOST_TOSSED }; @@ -404,7 +388,8 @@ struct brcmf_fws_mac_descriptor { u8 traffic_lastreported_bmp; }; -#define BRCMF_FWS_HANGER_MAXITEMS 1024 +#define BRCMF_FWS_HANGER_MAXITEMS 3072 +#define BRCMF_BORROW_RATIO 3 /** * enum brcmf_fws_hanger_item_state - state of hanger item. @@ -501,7 +486,8 @@ struct brcmf_fws_info { u32 fifo_enqpkt[BRCMF_FWS_FIFO_COUNT]; int fifo_credit[BRCMF_FWS_FIFO_COUNT]; int init_fifo_credit[BRCMF_FWS_FIFO_COUNT]; - int credits_borrowed[BRCMF_FWS_FIFO_AC_VO + 1]; + int credits_borrowed[BRCMF_FWS_FIFO_AC_VO + 1] + [BRCMF_FWS_FIFO_AC_VO + 1]; int deq_node_pos[BRCMF_FWS_FIFO_COUNT]; u32 fifo_credit_map; u32 fifo_delay_map; @@ -1213,11 +1199,11 @@ static void brcmf_fws_return_credits(struct brcmf_fws_info *fws, fws->fifo_credit_map |= 1 << fifo; - if ((fifo == BRCMF_FWS_FIFO_AC_BE) && - (fws->credits_borrowed[0])) { + if (fifo > BRCMF_FWS_FIFO_AC_BK && + fifo <= BRCMF_FWS_FIFO_AC_VO) { for (lender_ac = BRCMF_FWS_FIFO_AC_VO; lender_ac >= 0; lender_ac--) { - borrowed = &fws->credits_borrowed[lender_ac]; + borrowed = &fws->credits_borrowed[fifo][lender_ac]; if (*borrowed) { fws->fifo_credit_map |= (1 << lender_ac); fifo_credit = &fws->fifo_credit[lender_ac]; @@ -1234,7 +1220,10 @@ static void brcmf_fws_return_credits(struct brcmf_fws_info *fws, } } - fws->fifo_credit[fifo] += credits; + if (credits) { + fws->fifo_credit[fifo] += credits; + } + if (fws->fifo_credit[fifo] > fws->init_fifo_credit[fifo]) fws->fifo_credit[fifo] = fws->init_fifo_credit[fifo]; @@ -1477,6 +1466,10 @@ brcmf_fws_txs_process(struct brcmf_fws_info *fws, u8 flags, u32 hslot, remove_from_hanger = false; } else if (flags == BRCMF_FWS_TXSTATUS_FW_TOSSED) fws->stats.txs_tossed += compcnt; + else if (flags == BRCMF_FWS_TXSTATUS_FW_DISCARD_NOACK) + fws->stats.txs_discard += compcnt; + else if (flags == BRCMF_FWS_TXSTATUS_FW_SUPPRESS_ACKED) + fws->stats.txs_discard += compcnt; else if (flags == BRCMF_FWS_TXSTATUS_HOST_TOSSED) fws->stats.txs_host_tossed += compcnt; else @@ -1632,6 +1625,7 @@ static int brcmf_fws_notify_credit_map(struct brcmf_if *ifp, fws->fifo_credit_map |= 1 << i; else fws->fifo_credit_map &= ~(1 << i); + WARN_ONCE(fws->fifo_credit[i] < 0, "fifo_credit[%d] is negative(%d)\n", i, fws->fifo_credit[i]); @@ -1869,6 +1863,9 @@ void brcmf_fws_hdrpull(struct brcmf_if *ifp, s16 siglen, struct sk_buff *skb) WARN_ON(siglen > skb->len); + if (siglen > skb->len) + siglen = skb->len; + if (!siglen) return; /* if flow control disabled, skip to packet data and leave */ @@ -2031,27 +2028,31 @@ static void brcmf_fws_rollback_toq(struct brcmf_fws_info *fws, } } -static int brcmf_fws_borrow_credit(struct brcmf_fws_info *fws) +static int brcmf_fws_borrow_credit(struct brcmf_fws_info *fws, + int highest_lender_ac, int borrower_ac, + bool borrow_all) { - int lender_ac; + int lender_ac, borrow_limit = 0; - if (time_after(fws->borrow_defer_timestamp, jiffies)) { - fws->fifo_credit_map &= ~(1 << BRCMF_FWS_FIFO_AC_BE); - return -ENAVAIL; - } + for (lender_ac = 0; lender_ac <= highest_lender_ac; lender_ac++) { - for (lender_ac = 0; lender_ac <= BRCMF_FWS_FIFO_AC_VO; lender_ac++) { - if (fws->fifo_credit[lender_ac] > 0) { - fws->credits_borrowed[lender_ac]++; + if (!borrow_all) + borrow_limit = + fws->init_fifo_credit[lender_ac] / BRCMF_BORROW_RATIO; + else + borrow_limit = 0; + + if (fws->fifo_credit[lender_ac] > borrow_limit) { + fws->credits_borrowed[borrower_ac][lender_ac]++; fws->fifo_credit[lender_ac]--; if (fws->fifo_credit[lender_ac] == 0) fws->fifo_credit_map &= ~(1 << lender_ac); - fws->fifo_credit_map |= (1 << BRCMF_FWS_FIFO_AC_BE); + fws->fifo_credit_map |= (1 << borrower_ac); brcmf_dbg(DATA, "borrow credit from: %d\n", lender_ac); return 0; } } - fws->fifo_credit_map &= ~(1 << BRCMF_FWS_FIFO_AC_BE); + fws->fifo_credit_map &= ~(1 << borrower_ac); return -ENAVAIL; } @@ -2134,8 +2135,10 @@ int brcmf_fws_process_skb(struct brcmf_if *ifp, struct sk_buff *skb) skcb->if_flags = 0; skcb->state = BRCMF_FWS_SKBSTATE_NEW; brcmf_skb_if_flags_set_field(skb, INDEX, ifp->ifidx); + + /* mapping from 802.1d priority to firmware fifo index */ if (!multicast) - fifo = brcmf_fws_prio2fifo[skb->priority]; + fifo = brcmf_map_prio_to_aci(drvr->config, skb->priority); brcmf_fws_lock(fws); if (fifo != BRCMF_FWS_FIFO_AC_BE && fifo < BRCMF_FWS_FIFO_BCMC) @@ -2149,8 +2152,7 @@ int brcmf_fws_process_skb(struct brcmf_if *ifp, struct sk_buff *skb) brcmf_fws_enq(fws, BRCMF_FWS_SKBSTATE_DELAYED, fifo, skb); brcmf_fws_schedule_deq(fws); } else { - bphy_err(drvr, "drop skb: no hanger slot\n"); - brcmf_txfinalize(ifp, skb, false); + bphy_err(drvr, "no hanger slot available\n"); rc = -ENOMEM; } brcmf_fws_unlock(fws); @@ -2196,6 +2198,7 @@ void brcmf_fws_del_interface(struct brcmf_if *ifp) brcmf_fws_lock(fws); ifp->fws_desc = NULL; + brcmf_fws_macdesc_cleanup(fws, entry, ifp->ifidx); brcmf_dbg(TRACE, "deleting %s\n", entry->name); brcmf_fws_macdesc_cleanup(fws, &fws->desc.iface[ifp->ifidx], ifp->ifidx); @@ -2241,9 +2244,10 @@ static void brcmf_fws_dequeue_worker(struct work_struct *worker) } continue; } - while ((fws->fifo_credit[fifo] > 0) || + + while ((fws->fifo_credit[fifo]) || ((!fws->bcmc_credit_check) && - (fifo == BRCMF_FWS_FIFO_BCMC))) { + (fifo == BRCMF_FWS_FIFO_BCMC))) { skb = brcmf_fws_deq(fws, fifo); if (!skb) break; @@ -2253,10 +2257,14 @@ static void brcmf_fws_dequeue_worker(struct work_struct *worker) if (fws->bus_flow_blocked) break; } - if ((fifo == BRCMF_FWS_FIFO_AC_BE) && - (fws->fifo_credit[fifo] <= 0) && - (!fws->bus_flow_blocked)) { - while (brcmf_fws_borrow_credit(fws) == 0) { + + if (fifo >= BRCMF_FWS_FIFO_AC_BE && + fifo <= BRCMF_FWS_FIFO_AC_VO && + fws->fifo_credit[fifo] == 0 && + !fws->bus_flow_blocked) { + while (brcmf_fws_borrow_credit(fws, + fifo - 1, fifo, + true) == 0) { skb = brcmf_fws_deq(fws, fifo); if (!skb) { brcmf_fws_return_credits(fws, fifo, 1); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.h index b486d57..b16a9d1 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.h @@ -6,6 +6,29 @@ #ifndef FWSIGNAL_H_ #define FWSIGNAL_H_ +/** + * enum brcmf_fws_fifo - fifo indices used by dongle firmware. + * + * @BRCMF_FWS_FIFO_FIRST: first fifo, ie. background. + * @BRCMF_FWS_FIFO_AC_BK: fifo for background traffic. + * @BRCMF_FWS_FIFO_AC_BE: fifo for best-effort traffic. + * @BRCMF_FWS_FIFO_AC_VI: fifo for video traffic. + * @BRCMF_FWS_FIFO_AC_VO: fifo for voice traffic. + * @BRCMF_FWS_FIFO_BCMC: fifo for broadcast/multicast (AP only). + * @BRCMF_FWS_FIFO_ATIM: fifo for ATIM (AP only). + * @BRCMF_FWS_FIFO_COUNT: number of fifos. + */ +enum brcmf_fws_fifo { + BRCMF_FWS_FIFO_FIRST, + BRCMF_FWS_FIFO_AC_BK = BRCMF_FWS_FIFO_FIRST, + BRCMF_FWS_FIFO_AC_BE, + BRCMF_FWS_FIFO_AC_VI, + BRCMF_FWS_FIFO_AC_VO, + BRCMF_FWS_FIFO_BCMC, + BRCMF_FWS_FIFO_ATIM, + BRCMF_FWS_FIFO_COUNT +}; + struct brcmf_fws_info *brcmf_fws_attach(struct brcmf_pub *drvr); void brcmf_fws_detach(struct brcmf_fws_info *fws); void brcmf_fws_debugfs_create(struct brcmf_pub *drvr); diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c index e3dd862..373afdc 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.c @@ -54,6 +54,7 @@ #define BRCMF_IOCTL_REQ_PKTID 0xFFFE #define BRCMF_MSGBUF_MAX_PKT_SIZE 2048 +#define BRCMF_MSGBUF_MAX_CTL_PKT_SIZE 8192 #define BRCMF_MSGBUF_RXBUFPOST_THRESHOLD 32 #define BRCMF_MSGBUF_MAX_IOCTLRESPBUF_POST 8 #define BRCMF_MSGBUF_MAX_EVENTBUF_POST 8 @@ -70,6 +71,7 @@ #define BRCMF_MSGBUF_TRICKLE_TXWORKER_THRS 32 #define BRCMF_MSGBUF_UPDATE_RX_PTR_THRS 48 +#define BRCMF_MAX_TXSTATUS_WAIT_RETRIES 10 struct msgbuf_common_hdr { u8 msgtype; @@ -805,8 +807,12 @@ static int brcmf_msgbuf_tx_queue_data(struct brcmf_pub *drvr, int ifidx, flowid = brcmf_flowring_lookup(flow, eh->h_dest, skb->priority, ifidx); if (flowid == BRCMF_FLOWRING_INVALID_ID) { flowid = brcmf_msgbuf_flowring_create(msgbuf, ifidx, skb); - if (flowid == BRCMF_FLOWRING_INVALID_ID) + if (flowid == BRCMF_FLOWRING_INVALID_ID) { return -ENOMEM; + } else { + brcmf_flowring_enqueue(flow, flowid, skb); + return 0; + } } queue_count = brcmf_flowring_enqueue(flow, flowid, skb); force = ((queue_count % BRCMF_MSGBUF_TRICKLE_TXWORKER_THRS) == 0); @@ -1028,7 +1034,7 @@ brcmf_msgbuf_rxbuf_ctrl_post(struct brcmf_msgbuf *msgbuf, bool event_buf, rx_bufpost = (struct msgbuf_rx_ioctl_resp_or_event *)ret_ptr; memset(rx_bufpost, 0, sizeof(*rx_bufpost)); - skb = brcmu_pkt_buf_get_skb(BRCMF_MSGBUF_MAX_PKT_SIZE); + skb = brcmu_pkt_buf_get_skb(BRCMF_MSGBUF_MAX_CTL_PKT_SIZE); if (skb == NULL) { bphy_err(drvr, "Failed to alloc SKB\n"); @@ -1139,7 +1145,8 @@ brcmf_msgbuf_process_rx_complete(struct brcmf_msgbuf *msgbuf, void *buf) { struct brcmf_pub *drvr = msgbuf->drvr; struct msgbuf_rx_complete *rx_complete; - struct sk_buff *skb; + struct sk_buff *skb, *cpskb = NULL; + struct ethhdr *eh; u16 data_offset; u16 buflen; u16 flags; @@ -1188,6 +1195,34 @@ brcmf_msgbuf_process_rx_complete(struct brcmf_msgbuf *msgbuf, void *buf) return; } + if (ifp->isap && ifp->fmac_pkt_fwd_en) { + eh = (struct ethhdr *)(skb->data); + skb_set_network_header(skb, sizeof(struct ethhdr)); + skb->protocol = eh->h_proto; + skb->priority = cfg80211_classify8021d(skb, NULL); + if (is_unicast_ether_addr(eh->h_dest)) { + if (brcmf_find_sta(ifp, eh->h_dest)) { + /* determine the priority */ + if (skb->priority == 0 || skb->priority > 7) { + skb->priority = + cfg80211_classify8021d(skb, + NULL); + } + brcmf_proto_tx_queue_data(ifp->drvr, + ifp->ifidx, skb); + return; + } + } else { + cpskb = pskb_copy(skb, GFP_ATOMIC); + if (cpskb) { + brcmf_proto_tx_queue_data(ifp->drvr, + ifp->ifidx, + cpskb); + } else { + brcmf_err("Unable to do skb copy\n"); + } + } + } skb->protocol = eth_type_trans(skb, ifp->ndev); brcmf_netif_rx(ifp, skb); } @@ -1394,9 +1429,27 @@ void brcmf_msgbuf_delete_flowring(struct brcmf_pub *drvr, u16 flowid) struct brcmf_msgbuf *msgbuf = (struct brcmf_msgbuf *)drvr->proto->pd; struct msgbuf_tx_flowring_delete_req *delete; struct brcmf_commonring *commonring; + struct brcmf_commonring *commonring_del = msgbuf->flowrings[flowid]; + struct brcmf_flowring *flow = msgbuf->flow; void *ret_ptr; u8 ifidx; int err; + int retry = BRCMF_MAX_TXSTATUS_WAIT_RETRIES; + + /* make sure it is not in txflow */ + brcmf_commonring_lock(commonring_del); + flow->rings[flowid]->status = RING_CLOSING; + brcmf_commonring_unlock(commonring_del); + + /* wait for commonring txflow finished */ + while (retry && atomic_read(&commonring_del->outstanding_tx)) { + usleep_range(5000, 10000); + retry--; + } + if (!retry) { + brcmf_err("timed out waiting for txstatus\n"); + atomic_set(&commonring_del->outstanding_tx, 0); + } /* no need to submit if firmware can not be reached */ if (drvr->bus_if->state != BRCMF_BUS_UP) { diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c index b886b56..e4f3493 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c @@ -20,7 +20,8 @@ void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type, struct property *prop; int irq; u32 irqf; - u32 val; + u32 val32; + u16 val16; /* Set board-type to the first string of the machine compatible prop */ root = of_find_node_by_path("/"); @@ -34,8 +35,15 @@ void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type, !of_device_is_compatible(np, "brcm,bcm4329-fmac")) return; - if (of_property_read_u32(np, "brcm,drive-strength", &val) == 0) - sdio->drive_strength = val; + if (of_property_read_u32(np, "brcm,drive-strength", &val32) == 0) + sdio->drive_strength = val32; + + sdio->broken_sg_support = of_property_read_bool(np, + "brcm,broken_sg_support"); + if (of_property_read_u16(np, "brcm,sd_head_align", &val16) == 0) + sdio->sd_head_align = val16; + if (of_property_read_u16(np, "brcm,sd_sgentry_align", &val16) == 0) + sdio->sd_sgentry_align = val16; /* make sure there are interrupts defined in the node */ if (!of_find_property(np, "interrupts", NULL)) diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c index 1f5deea..8eb6d4f 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c @@ -17,6 +17,7 @@ #include "fwil_types.h" #include "p2p.h" #include "cfg80211.h" +#include "feature.h" /* parameters used for p2p escan */ #define P2PAPI_SCAN_NPROBES 1 @@ -59,12 +60,13 @@ #define P2P_AF_MIN_DWELL_TIME 100 #define P2P_AF_MED_DWELL_TIME 400 #define P2P_AF_LONG_DWELL_TIME 1000 -#define P2P_AF_TX_MAX_RETRY 1 +#define P2P_AF_TX_MAX_RETRY 5 #define P2P_AF_MAX_WAIT_TIME msecs_to_jiffies(2000) #define P2P_INVALID_CHANNEL -1 #define P2P_CHANNEL_SYNC_RETRY 5 #define P2P_AF_FRM_SCAN_MAX_WAIT msecs_to_jiffies(450) #define P2P_DEFAULT_SLEEP_TIME_VSDB 200 +#define P2P_AF_RETRY_DELAY_TIME 40 /* WiFi P2P Public Action Frame OUI Subtypes */ #define P2P_PAF_GON_REQ 0 /* Group Owner Negotiation Req */ @@ -92,6 +94,9 @@ #define P2PSD_ACTION_ID_GAS_CRESP 0x0d /* GAS Comback Response AF */ #define BRCMF_P2P_DISABLE_TIMEOUT msecs_to_jiffies(500) + +/* Mask for retry counter of custom dwell time */ +#define CUSTOM_RETRY_MASK 0xff000000 /** * struct brcmf_p2p_disc_st_le - set discovery state in firmware. * @@ -457,10 +462,21 @@ static int brcmf_p2p_set_firmware(struct brcmf_if *ifp, u8 *p2p_mac) */ static void brcmf_p2p_generate_bss_mac(struct brcmf_p2p_info *p2p, u8 *dev_addr) { + struct brcmf_if *pri_ifp = p2p->bss_idx[P2PAPI_BSSCFG_PRIMARY].vif->ifp; bool random_addr = false; + bool local_admin = false; - if (!dev_addr || is_zero_ether_addr(dev_addr)) - random_addr = true; + if (!dev_addr || is_zero_ether_addr(dev_addr)) { + /* If the primary interface address is already locally + * administered, create a new random address. + */ + if (pri_ifp->mac_addr[0] & 0x02) { + random_addr = true; + } else { + dev_addr = pri_ifp->mac_addr; + local_admin = true; + } + } /* Generate the P2P Device Address obtaining a random ethernet * address with the locally administered bit set. @@ -470,13 +486,20 @@ static void brcmf_p2p_generate_bss_mac(struct brcmf_p2p_info *p2p, u8 *dev_addr) else memcpy(p2p->dev_addr, dev_addr, ETH_ALEN); + if (local_admin) + p2p->dev_addr[0] |= 0x02; + /* Generate the P2P Interface Address. If the discovery and connection * BSSCFGs need to simultaneously co-exist, then this address must be * different from the P2P Device Address, but also locally administered. */ - memcpy(p2p->int_addr, p2p->dev_addr, ETH_ALEN); - p2p->int_addr[0] |= 0x02; - p2p->int_addr[4] ^= 0x80; + memcpy(p2p->conn_int_addr, p2p->dev_addr, ETH_ALEN); + p2p->conn_int_addr[0] |= 0x02; + p2p->conn_int_addr[4] ^= 0x80; + + memcpy(p2p->conn2_int_addr, p2p->dev_addr, ETH_ALEN); + p2p->conn2_int_addr[0] |= 0x02; + p2p->conn2_int_addr[4] ^= 0x90; } /** @@ -872,7 +895,7 @@ int brcmf_p2p_scan_prep(struct wiphy *wiphy, { struct brcmf_cfg80211_info *cfg = wiphy_to_cfg(wiphy); struct brcmf_p2p_info *p2p = &cfg->p2p; - int err; + int err = 0; if (brcmf_p2p_scan_is_p2p_request(request)) { /* find my listen channel */ @@ -895,7 +918,9 @@ int brcmf_p2p_scan_prep(struct wiphy *wiphy, /* override .run_escan() callback. */ cfg->escan_info.run = brcmf_p2p_run_escan; } - return 0; + err = brcmf_vif_set_mgmt_ie(vif, BRCMF_VNDR_IE_PRBREQ_FLAG, + request->ie, request->ie_len); + return err; } @@ -1244,6 +1269,30 @@ bool brcmf_p2p_scan_finding_common_channel(struct brcmf_cfg80211_info *cfg, return true; } +/** + * brcmf_p2p_abort_action_frame() - abort action frame. + * + * @cfg: common configuration struct. + * + */ +static s32 brcmf_p2p_abort_action_frame(struct brcmf_cfg80211_info *cfg) +{ + struct brcmf_p2p_info *p2p = &cfg->p2p; + struct brcmf_cfg80211_vif *vif; + s32 err; + s32 int_val = 1; + + brcmf_dbg(TRACE, "Enter\n"); + + vif = p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif; + err = brcmf_fil_bsscfg_data_set(vif->ifp, "actframe_abort", &int_val, + sizeof(s32)); + if (err) + brcmf_err(" aborting action frame has failed (%d)\n", err); + + return err; +} + /** * brcmf_p2p_stop_wait_next_action_frame() - finish scan if af tx complete. * @@ -1255,6 +1304,7 @@ brcmf_p2p_stop_wait_next_action_frame(struct brcmf_cfg80211_info *cfg) { struct brcmf_p2p_info *p2p = &cfg->p2p; struct brcmf_if *ifp = p2p->bss_idx[P2PAPI_BSSCFG_PRIMARY].vif->ifp; + s32 err; if (test_bit(BRCMF_P2P_STATUS_SENDING_ACT_FRAME, &p2p->status) && (test_bit(BRCMF_P2P_STATUS_ACTION_TX_COMPLETED, &p2p->status) || @@ -1263,8 +1313,13 @@ brcmf_p2p_stop_wait_next_action_frame(struct brcmf_cfg80211_info *cfg) /* if channel is not zero, "actfame" uses off channel scan. * So abort scan for off channel completion. */ - if (p2p->af_sent_channel) - brcmf_notify_escan_complete(cfg, ifp, true, true); + if (p2p->af_sent_channel) { + /* abort actframe using actframe_abort or abort scan */ + err = brcmf_p2p_abort_action_frame(cfg); + if (err) + brcmf_notify_escan_complete(cfg, ifp, true, + true); + } } else if (test_bit(BRCMF_P2P_STATUS_WAITING_NEXT_AF_LISTEN, &p2p->status)) { brcmf_dbg(TRACE, "*** Wake UP ** abort listen for next af frame\n"); @@ -1491,6 +1546,7 @@ static s32 brcmf_p2p_tx_action_frame(struct brcmf_p2p_info *p2p, { struct brcmf_pub *drvr = p2p->cfg->pub; struct brcmf_cfg80211_vif *vif; + struct brcmf_p2p_action_frame *p2p_act_frame; s32 err = 0; s32 timeout = 0; @@ -1500,7 +1556,13 @@ static s32 brcmf_p2p_tx_action_frame(struct brcmf_p2p_info *p2p, clear_bit(BRCMF_P2P_STATUS_ACTION_TX_COMPLETED, &p2p->status); clear_bit(BRCMF_P2P_STATUS_ACTION_TX_NOACK, &p2p->status); - vif = p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif; + /* check if it is a p2p_presence response */ + p2p_act_frame = (struct brcmf_p2p_action_frame *)af_params->action_frame.data; + if (p2p_act_frame->subtype == P2P_AF_PRESENCE_RSP) + vif = p2p->bss_idx[P2PAPI_BSSCFG_CONNECTION].vif; + else + vif = p2p->bss_idx[P2PAPI_BSSCFG_DEVICE].vif; + err = brcmf_fil_bsscfg_data_set(vif->ifp, "actframe", af_params, sizeof(*af_params)); if (err) { @@ -1640,6 +1702,17 @@ static s32 brcmf_p2p_pub_af_tx(struct brcmf_cfg80211_info *cfg, return err; } +static bool brcmf_p2p_check_dwell_overflow(s32 requested_dwell, + unsigned long dwell_jiffies) +{ + if ((requested_dwell & CUSTOM_RETRY_MASK) && + (jiffies_to_msecs(jiffies - dwell_jiffies) > + (requested_dwell & ~CUSTOM_RETRY_MASK))) { + brcmf_err("Action frame TX retry time over dwell time!\n"); + return true; + } + return false; +} /** * brcmf_p2p_send_action_frame() - send action frame . * @@ -1664,6 +1737,10 @@ bool brcmf_p2p_send_action_frame(struct brcmf_cfg80211_info *cfg, s32 tx_retry; s32 extra_listen_time; uint delta_ms; + unsigned long dwell_jiffies = 0; + bool dwell_overflow = false; + + s32 requested_dwell = af_params->dwell_time; action_frame = &af_params->action_frame; action_frame_len = le16_to_cpu(action_frame->len); @@ -1775,12 +1852,21 @@ bool brcmf_p2p_send_action_frame(struct brcmf_cfg80211_info *cfg, /* update channel */ af_params->channel = cpu_to_le32(afx_hdl->peer_chan); } + dwell_jiffies = jiffies; + dwell_overflow = brcmf_p2p_check_dwell_overflow(requested_dwell, + dwell_jiffies); tx_retry = 0; while (!p2p->block_gon_req_tx && - (ack == false) && (tx_retry < P2P_AF_TX_MAX_RETRY)) { + (!ack) && (tx_retry < P2P_AF_TX_MAX_RETRY) && + !dwell_overflow) { + if (af_params->channel) + msleep(P2P_AF_RETRY_DELAY_TIME); + ack = !brcmf_p2p_tx_action_frame(p2p, af_params); tx_retry++; + dwell_overflow = brcmf_p2p_check_dwell_overflow(requested_dwell, + dwell_jiffies); } if (ack == false) { bphy_err(drvr, "Failed to send Action Frame(retry %d)\n", @@ -1994,7 +2080,7 @@ int brcmf_p2p_ifchange(struct brcmf_cfg80211_info *cfg, if_request.type = cpu_to_le16((u16)if_type); if_request.chspec = cpu_to_le16(chanspec); - memcpy(if_request.addr, p2p->int_addr, sizeof(if_request.addr)); + memcpy(if_request.addr, p2p->conn_int_addr, sizeof(if_request.addr)); brcmf_cfg80211_arm_vif_event(cfg, vif); err = brcmf_fil_iovar_data_set(vif->ifp, "p2p_ifupd", &if_request, @@ -2092,8 +2178,7 @@ static struct wireless_dev *brcmf_p2p_create_p2pdev(struct brcmf_p2p_info *p2p, /* firmware requires unique mac address for p2pdev interface */ if (addr && ether_addr_equal(addr, pri_ifp->mac_addr)) { bphy_err(drvr, "discovery vif must be different from primary interface\n"); - err = -EINVAL; - goto fail; + return ERR_PTR(-EINVAL); } brcmf_p2p_generate_bss_mac(p2p, addr); @@ -2149,6 +2234,27 @@ fail: return ERR_PTR(err); } +int brcmf_p2p_get_conn_idx(struct brcmf_cfg80211_info *cfg) +{ + int i; + struct brcmf_if *ifp = netdev_priv(cfg_to_ndev(cfg)); + + if (!ifp) + return -ENODEV; + + for (i = P2PAPI_BSSCFG_CONNECTION; i < P2PAPI_BSSCFG_MAX; i++) { + if (!cfg->p2p.bss_idx[i].vif) { + if (i == P2PAPI_BSSCFG_CONNECTION2 && + !(brcmf_feat_is_enabled(ifp, BRCMF_FEAT_RSDB))) { + brcmf_err("Multi p2p not supported"); + return -EIO; + } + return i; + } + } + return -EIO; +} + /** * brcmf_p2p_add_vif() - create a new P2P virtual interface. * @@ -2168,7 +2274,9 @@ struct wireless_dev *brcmf_p2p_add_vif(struct wiphy *wiphy, const char *name, struct brcmf_pub *drvr = cfg->pub; struct brcmf_cfg80211_vif *vif; enum brcmf_fil_p2p_if_types iftype; - int err; + int err = 0; + int connidx; + u8 *p2p_intf_addr; if (brcmf_cfg80211_vif_event_armed(cfg)) return ERR_PTR(-EBUSY); @@ -2194,9 +2302,21 @@ struct wireless_dev *brcmf_p2p_add_vif(struct wiphy *wiphy, const char *name, return (struct wireless_dev *)vif; brcmf_cfg80211_arm_vif_event(cfg, vif); - err = brcmf_p2p_request_p2p_if(&cfg->p2p, ifp, cfg->p2p.int_addr, - iftype); + connidx = brcmf_p2p_get_conn_idx(cfg); + + if (connidx == P2PAPI_BSSCFG_CONNECTION) + p2p_intf_addr = cfg->p2p.conn_int_addr; + else if (connidx == P2PAPI_BSSCFG_CONNECTION2) + p2p_intf_addr = cfg->p2p.conn2_int_addr; + else + err = -EINVAL; + + if (!err) + err = brcmf_p2p_request_p2p_if(&cfg->p2p, ifp, + p2p_intf_addr, iftype); + if (err) { + brcmf_err("request p2p interface failed\n"); brcmf_cfg80211_arm_vif_event(cfg, NULL); goto fail; } @@ -2228,7 +2348,7 @@ struct wireless_dev *brcmf_p2p_add_vif(struct wiphy *wiphy, const char *name, goto fail; } - cfg->p2p.bss_idx[P2PAPI_BSSCFG_CONNECTION].vif = vif; + cfg->p2p.bss_idx[connidx].vif = vif; /* Disable firmware roaming for P2P interface */ brcmf_fil_iovar_int_set(ifp, "roam_off", 1); if (iftype == BRCMF_FIL_P2P_IF_GO) { diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.h index 64ab9b6..d2ecee5 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.h @@ -14,13 +14,15 @@ struct brcmf_cfg80211_info; * * @P2PAPI_BSSCFG_PRIMARY: maps to driver's primary bsscfg. * @P2PAPI_BSSCFG_DEVICE: maps to driver's P2P device discovery bsscfg. - * @P2PAPI_BSSCFG_CONNECTION: maps to driver's P2P connection bsscfg. + * @P2PAPI_BSSCFG_CONNECTION: maps to driver's 1st P2P connection bsscfg. + * @P2PAPI_BSSCFG_CONNECTION2: maps to driver's 2nd P2P connection bsscfg. * @P2PAPI_BSSCFG_MAX: used for range checking. */ enum p2p_bss_type { P2PAPI_BSSCFG_PRIMARY, /* maps to driver's primary bsscfg */ P2PAPI_BSSCFG_DEVICE, /* maps to driver's P2P device discovery bsscfg */ - P2PAPI_BSSCFG_CONNECTION, /* maps to driver's P2P connection bsscfg */ + P2PAPI_BSSCFG_CONNECTION, /* driver's 1st P2P connection bsscfg */ + P2PAPI_BSSCFG_CONNECTION2, /* driver's 2nd P2P connection bsscfg */ P2PAPI_BSSCFG_MAX }; @@ -119,7 +121,8 @@ struct brcmf_p2p_info { struct brcmf_cfg80211_info *cfg; unsigned long status; u8 dev_addr[ETH_ALEN]; - u8 int_addr[ETH_ALEN]; + u8 conn_int_addr[ETH_ALEN]; + u8 conn2_int_addr[ETH_ALEN]; struct p2p_bss bss_idx[P2PAPI_BSSCFG_MAX]; struct timer_list listen_timer; u8 listen_channel; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c index 941c488..af91044 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c @@ -38,6 +38,7 @@ #include "chip.h" #include "core.h" #include "common.h" +#include "cfg80211.h" enum brcmf_pcie_state { @@ -57,6 +58,8 @@ BRCMF_FW_DEF(4365C, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(4366B, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(4366C, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(4371, "/*(DEBLOBBED)*/"); +BRCMF_FW_DEF(4355, "/*(DEBLOBBED)*/"); +BRCMF_FW_DEF(54591, "/*(DEBLOBBED)*/"); static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43602_CHIP_ID, 0xFFFFFFFF, 43602), @@ -76,9 +79,11 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_4366_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_4371_CHIP_ID, 0xFFFFFFFF, 4371), + BRCMF_FW_ENTRY(CY_CC_89459_CHIP_ID, 0xFFFFFFFF, 4355), + BRCMF_FW_ENTRY(CY_CC_54591_CHIP_ID, 0xFFFFFFFF, 54591), }; -#define BRCMF_PCIE_FW_UP_TIMEOUT 2000 /* msec */ +#define BRCMF_PCIE_FW_UP_TIMEOUT 5000 /* msec */ #define BRCMF_PCIE_REG_MAP_SIZE (32 * 1024) @@ -269,6 +274,9 @@ struct brcmf_pciedev_info { void (*write_ptr)(struct brcmf_pciedev_info *devinfo, u32 mem_offset, u16 value); struct brcmf_mp_device *settings; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + ulong bar1_size; +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ }; struct brcmf_pcie_ringbuf { @@ -340,6 +348,10 @@ static void brcmf_pcie_setup(struct device *dev, int ret, static struct brcmf_fw_request * brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ +DEFINE_RAW_SPINLOCK(pcie_lock); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ + static u32 brcmf_pcie_read_reg32(struct brcmf_pciedev_info *devinfo, u32 reg_offset) { @@ -363,8 +375,24 @@ static u8 brcmf_pcie_read_tcm8(struct brcmf_pciedev_info *devinfo, u32 mem_offset) { void __iomem *address = devinfo->tcm + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; + u8 value; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + value = ioread8(address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); + return value; +#else return (ioread8(address)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -372,8 +400,24 @@ static u16 brcmf_pcie_read_tcm16(struct brcmf_pciedev_info *devinfo, u32 mem_offset) { void __iomem *address = devinfo->tcm + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + u16 value; + unsigned long flags; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + value = ioread16(address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); + return value; +#else return (ioread16(address)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -382,8 +426,22 @@ brcmf_pcie_write_tcm16(struct brcmf_pciedev_info *devinfo, u32 mem_offset, u16 value) { void __iomem *address = devinfo->tcm + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } iowrite16(value, address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#else + iowrite16(value, address); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -410,8 +468,24 @@ static u32 brcmf_pcie_read_tcm32(struct brcmf_pciedev_info *devinfo, u32 mem_offset) { void __iomem *address = devinfo->tcm + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + u32 value; + unsigned long flags; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + value = ioread32(address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); + return value; +#else return (ioread32(address)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -420,17 +494,47 @@ brcmf_pcie_write_tcm32(struct brcmf_pciedev_info *devinfo, u32 mem_offset, u32 value) { void __iomem *address = devinfo->tcm + mem_offset; - +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + iowrite32(value, address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#else iowrite32(value, address); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } static u32 brcmf_pcie_read_ram32(struct brcmf_pciedev_info *devinfo, u32 mem_offset) { - void __iomem *addr = devinfo->tcm + devinfo->ci->rambase + mem_offset; + void __iomem *address = devinfo->tcm + devinfo->ci->rambase + + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + u32 value; + unsigned long flags; + + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + value = ioread32(address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); - return (ioread32(addr)); + return value; +#else + return (ioread32(address)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -438,9 +542,23 @@ static void brcmf_pcie_write_ram32(struct brcmf_pciedev_info *devinfo, u32 mem_offset, u32 value) { - void __iomem *addr = devinfo->tcm + devinfo->ci->rambase + mem_offset; + void __iomem *address = devinfo->tcm + devinfo->ci->rambase + + mem_offset; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; - iowrite32(value, addr); + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= devinfo->bar1_size) { + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } + iowrite32(value, address); + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#else + iowrite32(value, address); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -452,12 +570,30 @@ brcmf_pcie_copy_mem_todev(struct brcmf_pciedev_info *devinfo, u32 mem_offset, __le32 *src32; __le16 *src16; u8 *src8; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ if (((ulong)address & 4) || ((ulong)srcaddr & 4) || (len & 4)) { if (((ulong)address & 2) || ((ulong)srcaddr & 2) || (len & 2)) { src8 = (u8 *)srcaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - + devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ iowrite8(*src8, address); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address++; src8++; len--; @@ -466,7 +602,22 @@ brcmf_pcie_copy_mem_todev(struct brcmf_pciedev_info *devinfo, u32 mem_offset, len = len / 2; src16 = (__le16 *)srcaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - + devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ iowrite16(le16_to_cpu(*src16), address); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address += 2; src16++; len--; @@ -476,12 +627,29 @@ brcmf_pcie_copy_mem_todev(struct brcmf_pciedev_info *devinfo, u32 mem_offset, len = len / 4; src32 = (__le32 *)srcaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ iowrite32(le32_to_cpu(*src32), address); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address += 4; src32++; len--; } } +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -493,12 +661,30 @@ brcmf_pcie_copy_dev_tomem(struct brcmf_pciedev_info *devinfo, u32 mem_offset, __le32 *dst32; __le16 *dst16; u8 *dst8; +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + unsigned long flags; +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ if (((ulong)address & 4) || ((ulong)dstaddr & 4) || (len & 4)) { if (((ulong)address & 2) || ((ulong)dstaddr & 2) || (len & 2)) { dst8 = (u8 *)dstaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - + devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ *dst8 = ioread8(address); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address++; dst8++; len--; @@ -507,7 +693,22 @@ brcmf_pcie_copy_dev_tomem(struct brcmf_pciedev_info *devinfo, u32 mem_offset, len = len / 2; dst16 = (__le16 *)dstaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - + devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ *dst16 = cpu_to_le16(ioread16(address)); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address += 2; dst16++; len--; @@ -517,12 +718,29 @@ brcmf_pcie_copy_dev_tomem(struct brcmf_pciedev_info *devinfo, u32 mem_offset, len = len / 4; dst32 = (__le32 *)dstaddr; while (len) { +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_lock_irqsave(&pcie_lock, flags); + if ((address - devinfo->tcm) >= + devinfo->bar1_size) { + pci_write_config_dword + (devinfo->pdev, + BCMA_PCI_BAR1_WIN, + devinfo->bar1_size); + address = address - devinfo->bar1_size; + } +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ *dst32 = cpu_to_le32(ioread32(address)); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + raw_spin_unlock_irqrestore(&pcie_lock, flags); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ address += 4; dst32++; len--; } } +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + pci_write_config_dword(devinfo->pdev, BCMA_PCI_BAR1_WIN, 0x0); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ } @@ -566,6 +784,9 @@ static void brcmf_pcie_reset_device(struct brcmf_pciedev_info *devinfo) BRCMF_PCIE_CFGREG_MSI_ADDR_L, BRCMF_PCIE_CFGREG_MSI_ADDR_H, BRCMF_PCIE_CFGREG_MSI_DATA, +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + BCMA_PCI_BAR1_WIN, +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ BRCMF_PCIE_CFGREG_LINK_STATUS_CTRL2, BRCMF_PCIE_CFGREG_RBAR_CTRL, BRCMF_PCIE_CFGREG_PML1_SUB_CTRL1, @@ -1136,9 +1357,14 @@ static int brcmf_pcie_init_ringbuffers(struct brcmf_pciedev_info *devinfo) u16 max_flowrings; u16 max_submissionrings; u16 max_completionrings; - +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + brcmf_pcie_copy_dev_tomem(devinfo, devinfo->shared.ring_info_addr, + &ringinfo, sizeof(ringinfo)); +#else memcpy_fromio(&ringinfo, devinfo->tcm + devinfo->shared.ring_info_addr, sizeof(ringinfo)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ + if (devinfo->shared.version >= 6) { max_submissionrings = le16_to_cpu(ringinfo.max_submissionrings); max_flowrings = le16_to_cpu(ringinfo.max_flowrings); @@ -1207,8 +1433,14 @@ static int brcmf_pcie_init_ringbuffers(struct brcmf_pciedev_info *devinfo) ringinfo.d2h_r_idx_hostaddr.high_addr = cpu_to_le32(address >> 32); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + brcmf_pcie_copy_mem_todev(devinfo, + devinfo->shared.ring_info_addr, + &ringinfo, sizeof(ringinfo)); +#else memcpy_toio(devinfo->tcm + devinfo->shared.ring_info_addr, &ringinfo, sizeof(ringinfo)); +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ brcmf_dbg(PCIE, "Using host memory indices\n"); } @@ -1403,12 +1635,21 @@ static int brcmf_pcie_get_fwname(struct device *dev, const char *ext, u8 *fw_name) { struct brcmf_bus *bus_if = dev_get_drvdata(dev); + struct brcmf_pciedev *buspub = bus_if->bus_priv.pcie; + struct brcmf_pciedev_info *devinfo = buspub->devinfo; struct brcmf_fw_request *fwreq; struct brcmf_fw_name fwnames[] = { { ext, fw_name }, }; + u32 chip; + + if (devinfo->ci->chip == CY_CC_89459_CHIP_ID && + devinfo->pdev->device == CY_PCIE_54591_DEVICE_ID) + chip = CY_CC_54591_CHIP_ID; + else + chip = bus_if->chip; - fwreq = brcmf_fw_alloc_request(bus_if->chip, bus_if->chiprev, + fwreq = brcmf_fw_alloc_request(chip, bus_if->chiprev, brcmf_pcie_fwnames, ARRAY_SIZE(brcmf_pcie_fwnames), fwnames, ARRAY_SIZE(fwnames)); @@ -1647,6 +1888,9 @@ static int brcmf_pcie_get_resource(struct brcmf_pciedev_info *devinfo) devinfo->regs = ioremap_nocache(bar0_addr, BRCMF_PCIE_REG_MAP_SIZE); devinfo->tcm = ioremap_nocache(bar1_addr, bar1_size); +#ifdef CONFIG_BRCMFMAC_PCIE_BARWIN_SZ + devinfo->bar1_size = bar1_size; +#endif /* CONFIG_BRCMFMAC_PCIE_BARWIN_SZ */ if (!devinfo->regs || !devinfo->tcm) { brcmf_err(bus, "ioremap() failed (%p,%p)\n", devinfo->regs, @@ -1827,7 +2071,7 @@ static void brcmf_pcie_setup(struct device *dev, int ret, brcmf_pcie_intr_enable(devinfo); brcmf_pcie_hostready(devinfo); - ret = brcmf_attach(&devinfo->pdev->dev); + ret = brcmf_attach(&devinfo->pdev->dev, true); if (ret) goto fail; @@ -1847,8 +2091,14 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) { ".bin", devinfo->fw_name }, { ".txt", devinfo->nvram_name }, }; + u32 chip; - fwreq = brcmf_fw_alloc_request(devinfo->ci->chip, devinfo->ci->chiprev, + if (devinfo->ci->chip == CY_CC_89459_CHIP_ID && + devinfo->pdev->device == CY_PCIE_54591_DEVICE_ID) + chip = CY_CC_54591_CHIP_ID; + else + chip = devinfo->ci->chip; + fwreq = brcmf_fw_alloc_request(chip, devinfo->ci->chiprev, brcmf_pcie_fwnames, ARRAY_SIZE(brcmf_pcie_fwnames), fwnames, ARRAY_SIZE(fwnames)); @@ -2011,11 +2261,22 @@ static int brcmf_pcie_pm_enter_D3(struct device *dev) { struct brcmf_pciedev_info *devinfo; struct brcmf_bus *bus; + struct brcmf_cfg80211_info *config; + int retry = BRCMF_PM_WAIT_MAXRETRY; brcmf_dbg(PCIE, "Enter\n"); bus = dev_get_drvdata(dev); devinfo = bus->bus_priv.pcie->devinfo; + config = bus->drvr->config; + + while (retry && + config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) { + usleep_range(10000, 20000); + retry--; + } + if (!retry && config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) + brcmf_err(bus, "timed out wait for cfg80211 suspended\n"); brcmf_bus_change_state(bus, BRCMF_BUS_DOWN); @@ -2101,6 +2362,7 @@ static const struct pci_device_id brcmf_pcie_devid_table[] = { BRCMF_PCIE_DEVICE(BRCM_PCIE_4356_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_43567_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_43570_DEVICE_ID), + BRCMF_PCIE_DEVICE(BRCM_PCIE_43570_RAW_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_4358_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_4359_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_43602_DEVICE_ID), @@ -2115,6 +2377,9 @@ static const struct pci_device_id brcmf_pcie_devid_table[] = { BRCMF_PCIE_DEVICE(BRCM_PCIE_4366_2G_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_4366_5G_DEVICE_ID), BRCMF_PCIE_DEVICE(BRCM_PCIE_4371_DEVICE_ID), + BRCMF_PCIE_DEVICE(CY_PCIE_89459_DEVICE_ID), + BRCMF_PCIE_DEVICE(CY_PCIE_89459_RAW_DEVICE_ID), + BRCMF_PCIE_DEVICE(CY_PCIE_54591_DEVICE_ID), { /* end: all zeroes */ } }; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c index ddc55ac..3209d76 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c @@ -16,6 +16,7 @@ #include #include #include +#include #include #include #include @@ -34,15 +35,30 @@ #include "core.h" #include "common.h" #include "bcdc.h" +#include "fwil.h" #define DCMD_RESP_TIMEOUT msecs_to_jiffies(2500) #define CTL_DONE_TIMEOUT msecs_to_jiffies(2500) +#define ULP_HUDI_PROC_DONE_TIME msecs_to_jiffies(2500) /* watermark expressed in number of words */ #define DEFAULT_F2_WATERMARK 0x8 #define CY_4373_F2_WATERMARK 0x40 #define CY_43012_F2_WATERMARK 0x60 - +#define CY_43012_MES_WATERMARK 0x50 +#define CY_43012_MESBUSYCTRL (CY_43012_MES_WATERMARK | \ + SBSDIO_MESBUSYCTRL_ENAB) +#define CY_4339_F2_WATERMARK 48 +#define CY_4339_MES_WATERMARK 80 +#define CY_4339_MESBUSYCTRL (CY_4339_MES_WATERMARK | \ + SBSDIO_MESBUSYCTRL_ENAB) +#define CY_43455_F2_WATERMARK 0x60 +#define CY_43455_MES_WATERMARK 0x50 +#define CY_43455_MESBUSYCTRL (CY_43455_MES_WATERMARK | \ + SBSDIO_MESBUSYCTRL_ENAB) +#define CY_435X_F2_WATERMARK 0x40 +#define CY_435X_F1_MESBUSYCTRL (CY_435X_F2_WATERMARK | \ + SBSDIO_MESBUSYCTRL_ENAB) #ifdef DEBUG #define BRCMF_TRAP_INFO_SIZE 80 @@ -311,16 +327,16 @@ struct rte_console { #define KSO_WAIT_US 50 #define MAX_KSO_ATTEMPTS (PMU_MAX_TRANSITION_DLY/KSO_WAIT_US) -#define BRCMF_SDIO_MAX_ACCESS_ERRORS 5 +#define BRCMF_SDIO_MAX_ACCESS_ERRORS 20 -/* - * Conversion of 802.1D priority to precedence level - */ -static uint prio2prec(u32 prio) -{ - return (prio == PRIO_8021D_NONE || prio == PRIO_8021D_BE) ? - (prio^2) : prio; -} +static void brcmf_sdio_firmware_callback(struct device *dev, int err, + struct brcmf_fw_request *fwreq); +static struct brcmf_fw_request * + brcmf_sdio_prepare_fw_request(struct brcmf_sdio *bus); +static int brcmf_sdio_f2_ready(struct brcmf_sdio *bus); +static int brcmf_ulp_event_notify(struct brcmf_if *ifp, + const struct brcmf_event_msg *evtmsg, + void *data); #ifdef DEBUG /* Device console log buffer state */ @@ -614,6 +630,7 @@ BRCMF_FW_DEF(43455, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(43456, "brcmfmac43456-sdio"); BRCMF_FW_DEF(4354, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(4356, "/*(DEBLOBBED)*/"); +BRCMF_FW_DEF(4359, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(4373, "/*(DEBLOBBED)*/"); BRCMF_FW_DEF(43012, "/*(DEBLOBBED)*/"); @@ -636,10 +653,13 @@ static const struct brcmf_firmware_mapping brcmf_sdio_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_4345_CHIP_ID, 0xFFFFFDC0, 43455), BRCMF_FW_ENTRY(BRCM_CC_4354_CHIP_ID, 0xFFFFFFFF, 4354), BRCMF_FW_ENTRY(BRCM_CC_4356_CHIP_ID, 0xFFFFFFFF, 4356), + BRCMF_FW_ENTRY(BRCM_CC_4359_CHIP_ID, 0xFFFFFFFF, 4359), BRCMF_FW_ENTRY(CY_CC_4373_CHIP_ID, 0xFFFFFFFF, 4373), BRCMF_FW_ENTRY(CY_CC_43012_CHIP_ID, 0xFFFFFFFF, 43012) }; +#define TXCTL_CREDITS 2 + static void pkt_align(struct sk_buff *p, int len, int align) { uint datalign; @@ -650,8 +670,17 @@ static void pkt_align(struct sk_buff *p, int len, int align) __skb_trim(p, len); } -/* To check if there's window offered */ +/* To check if there's window offered + * Reserve 3 credits for txctl + */ static bool data_ok(struct brcmf_sdio *bus) +{ + return (u8)(bus->tx_max - bus->tx_seq) > TXCTL_CREDITS && + ((u8)(bus->tx_max - bus->tx_seq) & 0x80) == 0; +} + +/* To check if there's window offered */ +static bool txctl_ok(struct brcmf_sdio *bus) { return (u8)(bus->tx_max - bus->tx_seq) != 0 && ((u8)(bus->tx_max - bus->tx_seq) & 0x80) == 0; @@ -1068,7 +1097,7 @@ static void brcmf_sdio_get_console_addr(struct brcmf_sdio *bus) } #endif /* DEBUG */ -static u32 brcmf_sdio_hostmail(struct brcmf_sdio *bus) +static u32 brcmf_sdio_hostmail(struct brcmf_sdio *bus, u32 *hmbd) { struct brcmf_sdio_dev *sdiod = bus->sdiodev; struct brcmf_core *core = bus->sdio_core; @@ -1157,6 +1186,9 @@ static u32 brcmf_sdio_hostmail(struct brcmf_sdio *bus) HMB_DATA_FCDATA_MASK | HMB_DATA_VERSION_MASK)) brcmf_err("Unknown mailbox data content: 0x%02x\n", hmb_data); + /* Populate hmb_data if argument is passed for DS1 check later */ + if (hmbd) + *hmbd = hmb_data; return intstatus; } @@ -1934,10 +1966,7 @@ static uint brcmf_sdio_readframes(struct brcmf_sdio *bus, uint maxframes) if (brcmf_sdio_hdparse(bus, bus->rxhdr, &rd_new, BRCMF_SDIO_FT_NORMAL)) { rd->len = 0; - brcmf_sdio_rxfail(bus, true, true); - sdio_release_host(bus->sdiodev->func1); brcmu_pkt_buf_free_skb(pkt); - continue; } bus->sdcnt.rx_readahead_cnt++; if (rd->len != roundup(rd_new.len, 16)) { @@ -2543,6 +2572,182 @@ static int brcmf_sdio_intr_rstatus(struct brcmf_sdio *bus) return ret; } +/* This Function is used to retrieve important + * details from dongle related to ULP mode Mostly + * values/SHM details that will be vary depending + * on the firmware branches + */ +static void +brcmf_sdio_ulp_preinit(struct device *dev) +{ + struct brcmf_bus *bus_if = dev_get_drvdata(dev); + struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio; + struct brcmf_if *ifp = bus_if->drvr->iflist[0]; + + brcmf_dbg(ULP, "Enter\n"); + + /* Query ulp_sdioctrl iovar to get the ULP related SHM offsets */ + brcmf_fil_iovar_data_get(ifp, "ulp_sdioctrl", + &sdiodev->fmac_ulp.ulp_shm_offset, + sizeof(sdiodev->fmac_ulp.ulp_shm_offset)); + + sdiodev->ulp = false; + + brcmf_dbg(ULP, "m_ulp_ctrl_sdio[%x] m_ulp_wakeevt_ind [%x]\n", + M_DS1_CTRL_SDIO(sdiodev->fmac_ulp), + M_WAKEEVENT_IND(sdiodev->fmac_ulp)); + brcmf_dbg(ULP, "m_ulp_wakeind [%x]\n", + M_ULP_WAKE_IND(sdiodev->fmac_ulp)); +} + +/* Reinitialize ARM because In DS1 mode ARM got off */ +static int +brcmf_sdio_ulp_reinit_fw(struct brcmf_sdio *bus) +{ + struct brcmf_sdio_dev *sdiodev = bus->sdiodev; + struct brcmf_fw_request *fwreq; + int err = 0; + + /* After firmware redownload tx/rx seq are reset accordingly + * these values are reset on FMAC side tx_max is initially set to 4, + * which later is updated by FW. + */ + bus->tx_seq = 0; + bus->rx_seq = 0; + bus->tx_max = 4; + + fwreq = brcmf_sdio_prepare_fw_request(bus); + if (!fwreq) + return -ENOMEM; + + err = brcmf_fw_get_firmwares(sdiodev->dev, fwreq, + brcmf_sdio_firmware_callback); + if (err != 0) { + brcmf_err("async firmware request failed: %d\n", err); + kfree(fwreq); + } + + return err; +} + +/* Check if device is in DS1 mode and handshake with ULP UCODE */ +static bool +brcmf_sdio_ulp_pre_redownload_check(struct brcmf_sdio *bus, u32 hmb_data) +{ + struct brcmf_sdio_dev *sdiod = bus->sdiodev; + int err = 0; + u32 value = 0; + u32 val32, ulp_wake_ind, wowl_wake_ind; + int reg_addr; + unsigned long timeout; + struct brcmf_ulp *fmac_ulp = &bus->sdiodev->fmac_ulp; + int i = 0; + + /* If any host mail box data is present, ignore DS1 exit sequence */ + if (hmb_data) + return false; + /* Skip if DS1 Exit is already in progress + * This can happen if firmware download is taking more time + */ + if (fmac_ulp->ulp_state == FMAC_ULP_TRIGGERED) + return false; + + value = brcmf_sdiod_func0_rb(sdiod, SDIO_CCCR_IOEx, &err); + + if (value == SDIO_FUNC_ENABLE_1) { + brcmf_dbg(ULP, "GOT THE INTERRUPT FROM UCODE\n"); + sdiod->ulp = true; + fmac_ulp->ulp_state = FMAC_ULP_TRIGGERED; + ulp_wake_ind = D11SHM_RDW(sdiod, + M_ULP_WAKE_IND(sdiod->fmac_ulp), + &err); + wowl_wake_ind = D11SHM_RDW(sdiod, + M_WAKEEVENT_IND(sdiod->fmac_ulp), + &err); + + brcmf_dbg(ULP, "wowl_wake_ind: 0x%08x, ulp_wake_ind: 0x%08x state %s\n", + wowl_wake_ind, ulp_wake_ind, (fmac_ulp->ulp_state) ? + "DS1 Exit Triggered" : "IDLE State"); + + if (wowl_wake_ind || ulp_wake_ind) { + /* RX wake Don't do anything. + * Just bail out and re-download firmware. + */ + /* Print out PHY TX error block when bit 9 set */ + if ((ulp_wake_ind & C_DS1_PHY_TXERR) && + M_DS1_PHYTX_ERR_BLK(sdiod->fmac_ulp)) { + brcmf_err("Dump PHY TX Error SHM Locations\n"); + for (i = 0; i < PHYTX_ERR_BLK_SIZE; i++) { + pr_err("0x%x", + D11SHM_RDW(sdiod, + (M_DS1_PHYTX_ERR_BLK(sdiod->fmac_ulp) + + (i * 2)), &err)); + } + brcmf_err("\n"); + } + } else { + /* TX wake negotiate with MAC */ + brcmf_dbg(ULP, "M_DS1_CTRL_SDIO: 0x%08x\n", + (u32)D11SHM_RDW(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + &err)); + val32 = D11SHM_RD(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + &err); + D11SHM_WR(sdiod, M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + val32, (C_DS1_CTRL_SDIO_DS1_EXIT | + C_DS1_CTRL_REQ_VALID), &err); + val32 = D11REG_RD(sdiod, D11_MACCONTROL_REG, &err); + val32 = val32 | D11_MACCONTROL_REG_WAKE; + D11REG_WR(sdiod, D11_MACCONTROL_REG, val32, &err); + + /* Poll for PROC_DONE to be set by ucode */ + value = D11SHM_RDW(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + &err); + /* Wait here (polling) for C_DS1_CTRL_PROC_DONE */ + timeout = jiffies + ULP_HUDI_PROC_DONE_TIME; + while (!(value & C_DS1_CTRL_PROC_DONE)) { + value = D11SHM_RDW(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + &err); + if (time_after(jiffies, timeout)) + break; + usleep_range(1000, 2000); + } + brcmf_dbg(ULP, "M_DS1_CTRL_SDIO: 0x%08x\n", + (u32)D11SHM_RDW(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), &err)); + value = D11SHM_RDW(sdiod, + M_DS1_CTRL_SDIO(sdiod->fmac_ulp), + &err); + if (!(value & C_DS1_CTRL_PROC_DONE)) { + brcmf_err("Timeout Failed to enter DS1 Exit state!\n"); + return false; + } + } + + ulp_wake_ind = D11SHM_RDW(sdiod, + M_ULP_WAKE_IND(sdiod->fmac_ulp), + &err); + wowl_wake_ind = D11SHM_RDW(sdiod, + M_WAKEEVENT_IND(sdiod->fmac_ulp), + &err); + brcmf_dbg(ULP, "wowl_wake_ind: 0x%08x, ulp_wake_ind: 0x%08x\n", + wowl_wake_ind, ulp_wake_ind); + reg_addr = CORE_CC_REG( + brcmf_chip_get_pmu(bus->ci)->base, min_res_mask); + brcmf_sdiod_writel(sdiod, reg_addr, + DEFAULT_43012_MIN_RES_MASK, &err); + if (err) + brcmf_err("min_res_mask failed\n"); + + return true; + } + + return false; +} + static void brcmf_sdio_dpc(struct brcmf_sdio *bus) { struct brcmf_sdio_dev *sdiod = bus->sdiodev; @@ -2614,8 +2819,11 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) /* Handle host mailbox indication */ if (intstatus & I_HMB_HOST_INT) { + u32 hmb_data = 0; intstatus &= ~I_HMB_HOST_INT; - intstatus |= brcmf_sdio_hostmail(bus); + intstatus |= brcmf_sdio_hostmail(bus, &hmb_data); + if (brcmf_sdio_ulp_pre_redownload_check(bus, hmb_data)) + brcmf_sdio_ulp_reinit_fw(bus); } sdio_release_host(bus->sdiodev->func1); @@ -2660,7 +2868,7 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) brcmf_sdio_clrintr(bus); if (bus->ctrl_frame_stat && (bus->clkstate == CLK_AVAIL) && - data_ok(bus)) { + txctl_ok(bus) && brcmf_sdio_f2_ready(bus)) { sdio_claim_host(bus->sdiodev->func1); if (bus->ctrl_frame_stat) { err = brcmf_sdio_tx_ctrlframe(bus, bus->ctrl_frame_buf, @@ -2668,6 +2876,9 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) bus->ctrl_frame_err = err; wmb(); bus->ctrl_frame_stat = false; + if (err) + brcmf_err("sdio ctrlframe tx failed err=%d\n", + err); } sdio_release_host(bus->sdiodev->func1); brcmf_sdio_wait_event_wakeup(bus); @@ -2770,7 +2981,13 @@ static int brcmf_sdio_bus_txdata(struct device *dev, struct sk_buff *pkt) skb_push(pkt, bus->tx_hdrlen); /* precondition: IS_ALIGNED((unsigned long)(pkt->data), 2) */ - prec = prio2prec((pkt->priority & PRIOMASK)); + /* In WLAN, priority is always set by the AP using WMM parameters + * and this need not always follow the standard 802.1d priority. + * Based on AP WMM config, map from 802.1d priority to corresponding + * precedence level. + */ + prec = brcmf_map_prio_to_prec(bus_if->drvr->config, + (pkt->priority & PRIOMASK)); /* Check for existing queue, current flow-control, pending event, or pending clock */ @@ -3378,7 +3595,12 @@ err: static bool brcmf_sdio_aos_no_decode(struct brcmf_sdio *bus) { - if (bus->ci->chip == CY_CC_43012_CHIP_ID) + if (bus->ci->chip == CY_CC_43012_CHIP_ID || + bus->ci->chip == CY_CC_4373_CHIP_ID || + bus->ci->chip == BRCM_CC_4339_CHIP_ID || + bus->ci->chip == BRCM_CC_4345_CHIP_ID || + bus->ci->chip == BRCM_CC_4354_CHIP_ID || + bus->ci->chip == BRCM_CC_4356_CHIP_ID) return true; else return false; @@ -3518,6 +3740,10 @@ static int brcmf_sdio_bus_preinit(struct device *dev) if (err < 0) goto done; + /* initialize SHM address from firmware for DS1 */ + if (!bus->sdiodev->ulp) + brcmf_sdio_ulp_preinit(dev); + bus->tx_hdrlen = SDPCM_HWHDR_LEN + SDPCM_SWHDR_LEN; if (sdiodev->sg_support) { bus->txglom = false; @@ -4099,6 +4325,36 @@ int brcmf_sdio_get_fwname(struct device *dev, const char *ext, u8 *fw_name) return 0; } +static int brcmf_sdio_bus_reset(struct device *dev) +{ + int ret = 0; + struct brcmf_bus *bus_if = dev_get_drvdata(dev); + struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio; + + brcmf_dbg(SDIO, "Enter\n"); + + /* start by unregistering irqs */ + brcmf_sdiod_intr_unregister(sdiodev); + + brcmf_sdiod_remove(sdiodev); + + /* reset the adapter */ + sdio_claim_host(sdiodev->func1); + mmc_hw_reset(sdiodev->func1->card->host); + sdio_release_host(sdiodev->func1); + + brcmf_bus_change_state(sdiodev->bus_if, BRCMF_BUS_DOWN); + + ret = brcmf_sdiod_probe(sdiodev); + if (ret) { + brcmf_err("Failed to probe after sdio device reset: ret %d\n", + ret); + brcmf_sdiod_remove(sdiodev); + } + + return ret; +} + static const struct brcmf_bus_ops brcmf_sdio_bus_ops = { .stop = brcmf_sdio_bus_stop, .preinit = brcmf_sdio_bus_preinit, @@ -4110,7 +4366,8 @@ static const struct brcmf_bus_ops brcmf_sdio_bus_ops = { .get_ramsize = brcmf_sdio_bus_get_ramsize, .get_memdump = brcmf_sdio_bus_get_memdump, .get_fwname = brcmf_sdio_get_fwname, - .debugfs_create = brcmf_sdio_debugfs_create + .debugfs_create = brcmf_sdio_debugfs_create, + .reset = brcmf_sdio_bus_reset }; #define BRCMF_SDIO_FW_CODE 0 @@ -4129,7 +4386,7 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, u8 saveclk, bpreq; u8 devctl; - brcmf_dbg(TRACE, "Enter: dev=%s, err=%d\n", dev_name(dev), err); + brcmf_dbg(ULP, "Enter: dev=%s, err=%d\n", dev_name(dev), err); if (err) goto fail; @@ -4211,6 +4468,50 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, devctl |= SBSDIO_DEVCTL_F2WM_ENAB; brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl, &err); + brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_MESBUSYCTRL, + CY_43012_MESBUSYCTRL, &err); + break; + case SDIO_DEVICE_ID_BROADCOM_4339: + brcmf_dbg(INFO, "set F2 watermark to 0x%x*4 bytes for 4339\n", + CY_4339_F2_WATERMARK); + brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK, + CY_4339_F2_WATERMARK, &err); + devctl = brcmf_sdiod_readb(sdiod, SBSDIO_DEVICE_CTL, + &err); + devctl |= SBSDIO_DEVCTL_F2WM_ENAB; + brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl, + &err); + brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_MESBUSYCTRL, + CY_4339_MESBUSYCTRL, &err); + break; + case SDIO_DEVICE_ID_BROADCOM_43455: + brcmf_dbg(INFO, "set F2 watermark to 0x%x*4 bytes for 43455\n", + CY_43455_F2_WATERMARK); + brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK, + CY_43455_F2_WATERMARK, &err); + devctl = brcmf_sdiod_readb(sdiod, SBSDIO_DEVICE_CTL, + &err); + devctl |= SBSDIO_DEVCTL_F2WM_ENAB; + brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl, + &err); + brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_MESBUSYCTRL, + CY_43455_MESBUSYCTRL, &err); + break; + case SDIO_DEVICE_ID_BROADCOM_4359: + case SDIO_DEVICE_ID_CYPRESS_89359: + case SDIO_DEVICE_ID_BROADCOM_4354: + case SDIO_DEVICE_ID_BROADCOM_4356: + brcmf_dbg(INFO, "set F2 watermark to 0x%x*4 bytes\n", + CY_435X_F2_WATERMARK); + brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK, + CY_435X_F2_WATERMARK, &err); + devctl = brcmf_sdiod_readb(sdiod, SBSDIO_DEVICE_CTL, + &err); + devctl |= SBSDIO_DEVCTL_F2WM_ENAB; + brcmf_sdiod_writeb(sdiod, SBSDIO_DEVICE_CTL, devctl, + &err); + brcmf_sdiod_writeb(sdiod, SBSDIO_FUNC1_MESBUSYCTRL, + CY_435X_F1_MESBUSYCTRL, &err); break; default: brcmf_sdiod_writeb(sdiod, SBSDIO_WATERMARK, @@ -4232,12 +4533,6 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, } if (err == 0) { - /* Assign bus interface call back */ - sdiod->bus_if->dev = sdiod->dev; - sdiod->bus_if->ops = &brcmf_sdio_bus_ops; - sdiod->bus_if->chip = bus->ci->chip; - sdiod->bus_if->chiprev = bus->ci->chiprev; - /* Allow full data communication using DPC from now on. */ brcmf_sdiod_change_state(bus->sdiodev, BRCMF_SDIOD_DATA); @@ -4254,6 +4549,12 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, sdio_release_host(sdiod->func1); + /* Assign bus interface call back */ + sdiod->bus_if->dev = sdiod->dev; + sdiod->bus_if->ops = &brcmf_sdio_bus_ops; + sdiod->bus_if->chip = bus->ci->chip; + sdiod->bus_if->chiprev = bus->ci->chiprev; + err = brcmf_alloc(sdiod->dev, sdiod->settings); if (err) { brcmf_err("brcmf_alloc failed\n"); @@ -4261,12 +4562,25 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, } /* Attach to the common layer, reserve hdr space */ - err = brcmf_attach(sdiod->dev); + err = brcmf_attach(sdiod->dev, !bus->sdiodev->ulp); if (err != 0) { brcmf_err("brcmf_attach failed\n"); goto free; } + /* Register for ULP events */ + if (sdiod->func1->device == SDIO_DEVICE_ID_CYPRESS_43012) + brcmf_fweh_register(bus_if->drvr, BRCMF_E_ULP, + brcmf_ulp_event_notify); + + if (bus->sdiodev->ulp) { + /* For ULP, after firmware redownload complete + * set ULP state to IDLE + */ + if (bus->sdiodev->fmac_ulp.ulp_state == FMAC_ULP_TRIGGERED) + bus->sdiodev->fmac_ulp.ulp_state = FMAC_ULP_IDLE; + } + /* ready */ return; @@ -4329,9 +4643,21 @@ struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev) bus->txminmax = BRCMF_TXMINMAX; bus->tx_seq = SDPCM_SEQ_WRAP - 1; + /* attempt to attach to the dongle */ + if (!(brcmf_sdio_probe_attach(bus))) { + brcmf_err("brcmf_sdio_probe_attach failed\n"); + goto fail; + } + /* single-threaded workqueue */ - wq = alloc_ordered_workqueue("brcmf_wq/%s", WQ_MEM_RECLAIM, - dev_name(&sdiodev->func1->dev)); + if (sdiodev->settings->sdio_wq_highpri) { + wq = alloc_workqueue("brcmf_wq/%s", + WQ_HIGHPRI | WQ_MEM_RECLAIM | WQ_UNBOUND, + 1, dev_name(&sdiodev->func1->dev)); + } else { + wq = alloc_ordered_workqueue("brcmf_wq/%s", WQ_MEM_RECLAIM, + dev_name(&sdiodev->func1->dev)); + } if (!wq) { brcmf_err("insufficient memory to create txworkqueue\n"); goto fail; @@ -4340,12 +4666,6 @@ struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev) INIT_WORK(&bus->datawork, brcmf_sdio_dataworker); bus->brcmf_wq = wq; - /* attempt to attach to the dongle */ - if (!(brcmf_sdio_probe_attach(bus))) { - brcmf_err("brcmf_sdio_probe_attach failed\n"); - goto fail; - } - spin_lock_init(&bus->rxctl_lock); spin_lock_init(&bus->txq_lock); init_waitqueue_head(&bus->ctrl_wait); @@ -4448,7 +4768,17 @@ void brcmf_sdio_remove(struct brcmf_sdio *bus) * necessary cores. */ msleep(20); - brcmf_chip_set_passive(bus->ci); + if (bus->sdiodev->fmac_ulp.ulp_state == + FMAC_ULP_ENTRY_RECV) { + brcmf_chip_ulp_reset_lhl_regs(bus->ci); + brcmf_chip_reset_pmu_regs(bus->ci); + } else { + brcmf_chip_set_passive(bus->ci); + } + /* Reset the PMU, backplane and all the + * cores by using the PMUWatchdogCounter. + */ + brcmf_chip_reset_watchdog(bus->ci); brcmf_sdio_clkctl(bus, CLK_NONE, false); sdio_release_host(bus->sdiodev->func1); } @@ -4504,3 +4834,39 @@ int brcmf_sdio_sleep(struct brcmf_sdio *bus, bool sleep) return ret; } +/* Check F2 Ready bit before sending data to Firmware */ +static int +brcmf_sdio_f2_ready(struct brcmf_sdio *bus) +{ + int ret = -1; + int iordy_status = 0; + + sdio_claim_host(bus->sdiodev->func1); + /* Read the status of IOR2 */ + iordy_status = brcmf_sdiod_func0_rb(bus->sdiodev, SDIO_CCCR_IORx, NULL); + + sdio_release_host(bus->sdiodev->func1); + ret = iordy_status & SDIO_FUNC_ENABLE_2; + return ret; +} + +static int brcmf_ulp_event_notify(struct brcmf_if *ifp, + const struct brcmf_event_msg *evtmsg, + void *data) +{ + int err = 0; + struct brcmf_bus *bus_if = ifp->drvr->bus_if; + struct brcmf_sdio_dev *sdiodev; + struct brcmf_sdio *bus; + struct brcmf_ulp_event *ulp_event = (struct brcmf_ulp_event *)data; + + sdiodev = bus_if->bus_priv.sdio; + bus = sdiodev->bus; + + brcmf_dbg(ULP, "Chip went to DS1 state : action %d\n", + ulp_event->ulp_dongle_action); + if (ulp_event->ulp_dongle_action == FMAC_ULP_ENTRY) + bus->sdiodev->fmac_ulp.ulp_state = FMAC_ULP_ENTRY_RECV; + + return err; +} diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h index 0bd47c1..d008689 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h @@ -165,6 +165,35 @@ struct brcmf_sdreg { struct brcmf_sdio; struct brcmf_sdiod_freezer; +/* ULP SHM Offsets info */ +struct ulp_shm_info { + u32 m_ulp_ctrl_sdio; + u32 m_ulp_wakeevt_ind; + u32 m_ulp_wakeind; + u32 m_ulp_phytxblk; +}; + +/* FMAC ULP state machine */ +#define FMAC_ULP_IDLE (0) +#define FMAC_ULP_ENTRY_RECV (1) +#define FMAC_ULP_TRIGGERED (2) + +/* BRCMF_E_ULP event data */ +#define FMAC_ULP_EVENT_VERSION 1 +#define FMAC_ULP_DISABLE_CONSOLE 1 /* Disable console */ +#define FMAC_ULP_UCODE_DOWNLOAD 2 /* Download ULP ucode file */ +#define FMAC_ULP_ENTRY 3 /* Inform ulp entry to Host */ + +struct brcmf_ulp { + uint ulp_state; + struct ulp_shm_info ulp_shm_offset; +}; + +struct brcmf_ulp_event { + u16 version; + u16 ulp_dongle_action; +}; + struct brcmf_sdio_dev { struct sdio_func *func1; struct sdio_func *func2; @@ -190,6 +219,8 @@ struct brcmf_sdio_dev { bool wowl_enabled; enum brcmf_sdiod_state state; struct brcmf_sdiod_freezer *freezer; + struct brcmf_ulp fmac_ulp; + bool ulp; }; /* sdio core registers */ @@ -368,6 +399,9 @@ static inline void brcmf_sdiod_freezer_uncount(struct brcmf_sdio_dev *sdiodev) } #endif /* CONFIG_PM_SLEEP */ +int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev); +int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev); + struct brcmf_sdio *brcmf_sdio_probe(struct brcmf_sdio_dev *sdiodev); void brcmf_sdio_remove(struct brcmf_sdio *bus); void brcmf_sdio_isr(struct brcmf_sdio *bus); @@ -377,4 +411,83 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled); int brcmf_sdio_sleep(struct brcmf_sdio *bus, bool sleep); void brcmf_sdio_trigger_dpc(struct brcmf_sdio *bus); +/* SHM offsets */ +#define M_DS1_CTRL_SDIO(ptr) ((ptr).ulp_shm_offset.m_ulp_ctrl_sdio) +#define M_WAKEEVENT_IND(ptr) ((ptr).ulp_shm_offset.m_ulp_wakeevt_ind) +#define M_ULP_WAKE_IND(ptr) ((ptr).ulp_shm_offset.m_ulp_wakeind) +#define M_DS1_PHYTX_ERR_BLK(ptr) ((ptr).ulp_shm_offset.m_ulp_phytxblk) + +#define D11_BASE_ADDR 0x18001000 +#define D11_AXI_BASE_ADDR 0xE8000000 +#define D11_SHM_BASE_ADDR (D11_AXI_BASE_ADDR + 0x4000) + +#define D11REG_ADDR(offset) (D11_BASE_ADDR + (offset)) +#define D11IHR_ADDR(offset) (D11_AXI_BASE_ADDR + 0x400 + (2 * (offset))) +#define D11SHM_ADDR(offset) (D11_SHM_BASE_ADDR + (offset)) + +/* MacControl register */ +#define D11_MACCONTROL_REG D11REG_ADDR(0x120) +#define D11_MACCONTROL_REG_WAKE 0x4000000 + +/* HUDI Sequence SHM bits */ +#define C_DS1_CTRL_SDIO_DS1_SLEEP 0x1 +#define C_DS1_CTRL_SDIO_MAC_ON 0x2 +#define C_DS1_CTRL_SDIO_RADIO_PHY_ON 0x4 +#define C_DS1_CTRL_SDIO_DS1_EXIT 0x8 +#define C_DS1_CTRL_PROC_DONE 0x100 +#define C_DS1_CTRL_REQ_VALID 0x200 + +/* M_ULP_WAKEIND bits */ +#define C_WATCHDOG_EXPIRY BIT(0) +#define C_FCBS_ERROR BIT(1) +#define C_RETX_FAILURE BIT(2) +#define C_HOST_WAKEUP BIT(3) +#define C_INVALID_FCBS_BLOCK BIT(4) +#define C_HUDI_DS1_EXIT BIT(5) +#define C_LOB_SLEEP BIT(6) +#define C_DS1_PHY_TXERR BIT(9) +#define C_DS1_WAKE_TIMER BIT(10) + +#define PHYTX_ERR_BLK_SIZE 18 +#define D11SHM_FIRST2BYTE_MASK 0xFFFF0000 +#define D11SHM_SECOND2BYTE_MASK 0x0000FFFF +#define D11SHM_2BYTE_SHIFT 16 + +#define D11SHM_RD(sdh, offset, ret) \ + brcmf_sdiod_readl(sdh, D11SHM_ADDR(offset), ret) + +/* SHM Read is motified based on SHM 4 byte alignment as SHM size is 2 bytes and + * 2 byte is currently not working on FMAC + * If SHM address is not 4 byte aligned, then right shift by 16 + * otherwise, mask the first two MSB bytes + * Suppose data in address 7260 is 0x440002 and it is 4 byte aligned + * Correct SHM value is 0x2 for this SHM offset and next SHM value is 0x44 + */ +#define D11SHM_RDW(sdh, offset, ret) \ + ((offset % 4) ? \ + (brcmf_sdiod_readl(sdh, D11SHM_ADDR(offset), ret) \ + >> D11SHM_2BYTE_SHIFT) : \ + (brcmf_sdiod_readl(sdh, D11SHM_ADDR(offset), ret) \ + & D11SHM_SECOND2BYTE_MASK)) + +/* SHM is of size 2 bytes, 4 bytes write will overwrite other SHM's + * First read 4 bytes and then clear the required two bytes based on + * 4 byte alignment, then update the required value and write the + * 4 byte value now + */ +#define D11SHM_WR(sdh, offset, val, mask, ret) \ + do { \ + if ((offset) % 4) \ + val = (val & D11SHM_SECOND2BYTE_MASK) | \ + ((mask) << D11SHM_2BYTE_SHIFT); \ + else \ + val = (mask) | (val & D11SHM_FIRST2BYTE_MASK); \ + brcmf_sdiod_writel(sdh, D11SHM_ADDR(offset), val, ret); \ + } while (0) +#define D11REG_WR(sdh, addr, val, ret) \ + brcmf_sdiod_writel(sdh, addr, val, ret) + +#define D11REG_RD(sdh, addr, ret) \ + brcmf_sdiod_readl(sdh, addr, ret) + #endif /* BRCMFMAC_SDIO_H */ diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c index 8021abe..8a21406 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c @@ -19,6 +19,7 @@ #include "core.h" #include "common.h" #include "bcdc.h" +#include "cfg80211.h" #define IOCTL_RESP_TIMEOUT msecs_to_jiffies(2000) @@ -164,7 +165,6 @@ struct brcmf_usbdev_info { struct urb *bulk_urb; /* used for FW download */ - bool wowl_enabled; struct brcmf_mp_device *settings; }; @@ -312,27 +312,43 @@ static int brcmf_usb_tx_ctlpkt(struct device *dev, u8 *buf, u32 len) int err = 0; int timeout = 0; struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(dev); + struct usb_interface *intf = to_usb_interface(dev); brcmf_dbg(USB, "Enter\n"); - if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) - return -EIO; - if (test_and_set_bit(0, &devinfo->ctl_op)) - return -EIO; + err = usb_autopm_get_interface(intf); + if (err) + goto out; + + if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) { + err = -EIO; + goto fail; + } + + if (test_and_set_bit(0, &devinfo->ctl_op)) { + err = -EIO; + goto fail; + } devinfo->ctl_completed = false; err = brcmf_usb_send_ctl(devinfo, buf, len); if (err) { brcmf_err("fail %d bytes: %d\n", err, len); clear_bit(0, &devinfo->ctl_op); - return err; + goto fail; } timeout = brcmf_usb_ioctl_resp_wait(devinfo); - clear_bit(0, &devinfo->ctl_op); if (!timeout) { brcmf_err("Txctl wait timed out\n"); + usb_kill_urb(devinfo->ctl_urb); err = -EIO; + goto fail; } + clear_bit(0, &devinfo->ctl_op); + +fail: + usb_autopm_put_interface(intf); +out: return err; } @@ -341,32 +357,46 @@ static int brcmf_usb_rx_ctlpkt(struct device *dev, u8 *buf, u32 len) int err = 0; int timeout = 0; struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(dev); + struct usb_interface *intf = to_usb_interface(dev); brcmf_dbg(USB, "Enter\n"); - if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) - return -EIO; - if (test_and_set_bit(0, &devinfo->ctl_op)) - return -EIO; + err = usb_autopm_get_interface(intf); + if (err) + goto out; + + if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) { + err = -EIO; + goto fail; + } + + if (test_and_set_bit(0, &devinfo->ctl_op)) { + err = -EIO; + goto fail; + } devinfo->ctl_completed = false; err = brcmf_usb_recv_ctl(devinfo, buf, len); if (err) { brcmf_err("fail %d bytes: %d\n", err, len); clear_bit(0, &devinfo->ctl_op); - return err; + goto fail; } timeout = brcmf_usb_ioctl_resp_wait(devinfo); err = devinfo->ctl_urb_status; - clear_bit(0, &devinfo->ctl_op); if (!timeout) { brcmf_err("rxctl wait timed out\n"); + usb_kill_urb(devinfo->ctl_urb); err = -EIO; + goto fail; } + clear_bit(0, &devinfo->ctl_op); +fail: + usb_autopm_put_interface(intf); if (!err) return devinfo->ctl_urb_actual_length; - else - return err; +out: + return err; } static struct brcmf_usbreq *brcmf_usb_deq(struct brcmf_usbdev_info *devinfo, @@ -430,7 +460,6 @@ fail: usb_free_urb(req->urb); list_del(q->next); } - kfree(reqs); return NULL; } @@ -500,10 +529,12 @@ static void brcmf_usb_rx_complete(struct urb *urb) return; } - if (devinfo->bus_pub.state == BRCMFMAC_USB_STATE_UP) { + if (devinfo->bus_pub.state == BRCMFMAC_USB_STATE_UP || + devinfo->bus_pub.state == BRCMFMAC_USB_STATE_SLEEP) { skb_put(skb, urb->actual_length); brcmf_rx_frame(devinfo->dev, skb, true); brcmf_usb_rx_refill(devinfo, req); + usb_mark_last_busy(urb->dev); } else { brcmu_pkt_buf_free_skb(skb); brcmf_usb_enq(devinfo, &devinfo->rx_freeq, req, NULL); @@ -587,6 +618,11 @@ static int brcmf_usb_tx(struct device *dev, struct sk_buff *skb) struct brcmf_usbreq *req; int ret; unsigned long flags; + struct usb_interface *intf = to_usb_interface(dev); + + ret = usb_autopm_get_interface(intf); + if (ret) + goto out; brcmf_dbg(USB, "Enter, skb=%p\n", skb); if (devinfo->bus_pub.state != BRCMFMAC_USB_STATE_UP) { @@ -625,9 +661,10 @@ static int brcmf_usb_tx(struct device *dev, struct sk_buff *skb) devinfo->tx_flowblock = true; } spin_unlock_irqrestore(&devinfo->tx_flowblock_lock, flags); - return 0; fail: + usb_autopm_put_interface(intf); +out: return ret; } @@ -991,20 +1028,32 @@ static int brcmf_usb_fw_download(struct brcmf_usbdev_info *devinfo) { int err; + struct usb_interface *intf; brcmf_dbg(USB, "Enter\n"); - if (devinfo == NULL) - return -ENODEV; + if (!devinfo) { + err = -ENODEV; + goto out; + } if (!devinfo->image) { brcmf_err("No firmware!\n"); - return -ENOENT; + err = -ENOENT; + goto out; } + intf = to_usb_interface(devinfo->dev); + err = usb_autopm_get_interface(intf); + if (err) + goto out; + err = brcmf_usb_dlstart(devinfo, (u8 *)devinfo->image, devinfo->image_len); if (err == 0) err = brcmf_usb_dlrun(devinfo); + + usb_autopm_put_interface(intf); +out: return err; } @@ -1105,18 +1154,6 @@ error: return NULL; } -static void brcmf_usb_wowl_config(struct device *dev, bool enabled) -{ - struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(dev); - - brcmf_dbg(USB, "Configuring WOWL, enabled=%d\n", enabled); - devinfo->wowl_enabled = enabled; - if (enabled) - device_set_wakeup_enable(devinfo->dev, true); - else - device_set_wakeup_enable(devinfo->dev, false); -} - static int brcmf_usb_get_fwname(struct device *dev, const char *ext, u8 *fw_name) { @@ -1143,7 +1180,6 @@ static const struct brcmf_bus_ops brcmf_usb_bus_ops = { .txdata = brcmf_usb_tx, .txctl = brcmf_usb_tx_ctlpkt, .rxctl = brcmf_usb_rx_ctlpkt, - .wowl_config = brcmf_usb_wowl_config, .get_fwname = brcmf_usb_get_fwname, }; @@ -1183,8 +1219,14 @@ static void brcmf_usb_probe_phase2(struct device *dev, int ret, if (ret) goto error; + if (BRCMF_FWCON_ON()) { + ret = brcmf_fwlog_attach(devinfo->dev); + if (ret) + goto error; + } + /* Attach to the common driver interface */ - ret = brcmf_attach(devinfo->dev); + ret = brcmf_attach(devinfo->dev, true); if (ret) goto error; @@ -1259,9 +1301,17 @@ static int brcmf_usb_probe_cb(struct brcmf_usbdev_info *devinfo) ret = brcmf_alloc(devinfo->dev, devinfo->settings); if (ret) goto fail; - ret = brcmf_attach(devinfo->dev); + + if (BRCMF_FWCON_ON()) { + ret = brcmf_fwlog_attach(devinfo->dev); + if (ret) + goto fail; + } + + ret = brcmf_attach(devinfo->dev, true); if (ret) goto fail; + /* we are done */ complete(&devinfo->dev_init_done); return 0; @@ -1332,6 +1382,8 @@ brcmf_usb_probe(struct usb_interface *intf, const struct usb_device_id *id) usb_set_intfdata(intf, devinfo); + intf->needs_remote_wakeup = 1; + /* Check that the device supports only one configuration */ if (usb->descriptor.bNumConfigurations != 1) { brcmf_err("Number of configurations: %d not supported\n", @@ -1442,15 +1494,25 @@ static int brcmf_usb_suspend(struct usb_interface *intf, pm_message_t state) { struct usb_device *usb = interface_to_usbdev(intf); struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(&usb->dev); + struct brcmf_bus *bus; + struct brcmf_cfg80211_info *config; + int retry = BRCMF_PM_WAIT_MAXRETRY; brcmf_dbg(USB, "Enter\n"); - devinfo->bus_pub.state = BRCMFMAC_USB_STATE_SLEEP; - if (devinfo->wowl_enabled) { - brcmf_cancel_all_urbs(devinfo); - } else { - brcmf_detach(&usb->dev); - brcmf_free(&usb->dev); + + bus = devinfo->bus_pub.bus; + config = bus->drvr->config; + while (retry && + config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) { + usleep_range(10000, 20000); + retry--; } + if (!retry && config->pm_state == BRCMF_CFG80211_PM_STATE_SUSPENDING) + brcmf_err("timed out wait for cfg80211 suspended\n"); + + devinfo->bus_pub.state = BRCMFMAC_USB_STATE_SLEEP; + brcmf_cancel_all_urbs(devinfo); + device_set_wakeup_enable(devinfo->dev, true); return 0; } @@ -1463,22 +1525,10 @@ static int brcmf_usb_resume(struct usb_interface *intf) struct brcmf_usbdev_info *devinfo = brcmf_usb_get_businfo(&usb->dev); brcmf_dbg(USB, "Enter\n"); - if (!devinfo->wowl_enabled) { - int err; - - err = brcmf_alloc(&usb->dev, devinfo->settings); - if (err) - return err; - - err = brcmf_attach(devinfo->dev); - if (err) { - brcmf_free(devinfo->dev); - return err; - } - } devinfo->bus_pub.state = BRCMFMAC_USB_STATE_UP; brcmf_usb_rx_fill_all(devinfo); + device_set_wakeup_enable(devinfo->dev, false); return 0; } @@ -1535,6 +1585,7 @@ static struct usb_driver brcmf_usbdrvr = { .suspend = brcmf_usb_suspend, .resume = brcmf_usb_resume, .reset_resume = brcmf_usb_reset_resume, + .supports_autosuspend = true, .disable_hub_initiated_lpm = 1, }; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.c index d07e7c7..0bad78d 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.c +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.c @@ -64,6 +64,15 @@ static int brcmf_cfg80211_vndr_cmds_dcmd_handler(struct wiphy *wiphy, *(char *)(dcmd_buf + len) = '\0'; } + if (cmdhdr->cmd == BRCMF_C_SET_AP) { + if (*(int *)(dcmd_buf) == 1) { + ifp->vif->wdev.iftype = NL80211_IFTYPE_AP; + brcmf_net_setcarrier(ifp, true); + } else { + ifp->vif->wdev.iftype = NL80211_IFTYPE_STATION; + } + } + if (cmdhdr->set) ret = brcmf_fil_cmd_data_set(ifp, cmdhdr->cmd, dcmd_buf, ret_len); @@ -104,6 +113,56 @@ exit: return ret; } +s32 +brcmf_wiphy_phy_temp_evt_handler(struct brcmf_if *ifp, + const struct brcmf_event_msg *e, void *data) + +{ + struct brcmf_cfg80211_info *cfg = ifp->drvr->config; + struct wiphy *wiphy = cfg_to_wiphy(cfg); + struct sk_buff *skb; + struct nlattr *phy_temp_data; + u32 version, temp, tempdelta; + struct brcmf_phy_temp_evt *phy_temp_evt; + + phy_temp_evt = (struct brcmf_phy_temp_evt *)data; + + version = le32_to_cpu(phy_temp_evt->version); + temp = le32_to_cpu(phy_temp_evt->temp); + tempdelta = le32_to_cpu(phy_temp_evt->tempdelta); + + skb = cfg80211_vendor_event_alloc(wiphy, NULL, + sizeof(*phy_temp_evt), + BRCMF_VNDR_EVTS_PHY_TEMP, + GFP_KERNEL); + + if (!skb) { + brcmf_dbg(EVENT, "NO MEM: can't allocate skb for vendor PHY_TEMP_EVENT\n"); + return -ENOMEM; + } + + phy_temp_data = nla_nest_start(skb, NL80211_ATTR_VENDOR_EVENTS); + if (!phy_temp_data) { + nla_nest_cancel(skb, phy_temp_data); + kfree_skb(skb); + brcmf_dbg(EVENT, "skb could not nest vendor attributes\n"); + return -EMSGSIZE; + } + + if (nla_put_u32(skb, BRCMF_NLATTR_VERS, version) || + nla_put_u32(skb, BRCMF_NLATTR_PHY_TEMP, temp) || + nla_put_u32(skb, BRCMF_NLATTR_PHY_TEMPDELTA, tempdelta)) { + kfree_skb(skb); + brcmf_dbg(EVENT, "NO ROOM in skb for vendor PHY_TEMP_EVENT\n"); + return -EMSGSIZE; + } + + nla_nest_end(skb, phy_temp_data); + + cfg80211_vendor_event(skb, GFP_KERNEL); + return 0; +} + const struct wiphy_vendor_command brcmf_vendor_cmds[] = { { { @@ -116,3 +175,10 @@ const struct wiphy_vendor_command brcmf_vendor_cmds[] = { .doit = brcmf_cfg80211_vndr_cmds_dcmd_handler }, }; + +const struct nl80211_vendor_cmd_info brcmf_vendor_events[] = { + { + .vendor_id = BROADCOM_OUI, + .subcmd = BRCMF_VNDR_EVTS_PHY_TEMP, + }, +}; diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.h b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.h index 418f33e..3bdf473 100644 --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.h +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/vendor.h @@ -14,6 +14,11 @@ enum brcmf_vndr_cmds { BRCMF_VNDR_CMDS_LAST }; +enum brcmf_vndr_evts { + BRCMF_VNDR_EVTS_PHY_TEMP, + BRCMF_VNDR_EVTS_LAST +}; + /** * enum brcmf_nlattrs - nl80211 message attributes * @@ -25,11 +30,21 @@ enum brcmf_nlattrs { BRCMF_NLATTR_LEN, BRCMF_NLATTR_DATA, + BRCMF_NLATTR_VERS, + BRCMF_NLATTR_PHY_TEMP, + BRCMF_NLATTR_PHY_TEMPDELTA, __BRCMF_NLATTR_AFTER_LAST, BRCMF_NLATTR_MAX = __BRCMF_NLATTR_AFTER_LAST - 1 }; +/* structure of event sent up by firmware: is this the right place for it? */ +struct brcmf_phy_temp_evt { + __le32 version; + __le32 temp; + __le32 tempdelta; +} __packed; + /** * struct brcmf_vndr_dcmd_hdr - message header for cfg80211 vendor command dcmd * support @@ -49,5 +64,9 @@ struct brcmf_vndr_dcmd_hdr { }; extern const struct wiphy_vendor_command brcmf_vendor_cmds[]; +extern const struct nl80211_vendor_cmd_info brcmf_vendor_events[]; +s32 brcmf_wiphy_phy_temp_evt_handler(struct brcmf_if *ifp, + const struct brcmf_event_msg *e, + void *data); #endif /* _vendor_h_ */ diff --git a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h index d1037b6..1a04157 100644 --- a/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h +++ b/drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h @@ -50,6 +50,8 @@ #define BRCM_CC_4371_CHIP_ID 0x4371 #define CY_CC_4373_CHIP_ID 0x4373 #define CY_CC_43012_CHIP_ID 43012 +#define CY_CC_89459_CHIP_ID 0x4355 +#define CY_CC_54591_CHIP_ID 0x54591 /* USB Device IDs */ #define BRCM_USB_43143_DEVICE_ID 0xbd1e @@ -68,6 +70,7 @@ #define BRCM_PCIE_4356_DEVICE_ID 0x43ec #define BRCM_PCIE_43567_DEVICE_ID 0x43d3 #define BRCM_PCIE_43570_DEVICE_ID 0x43d9 +#define BRCM_PCIE_43570_RAW_DEVICE_ID 0xaa31 #define BRCM_PCIE_4358_DEVICE_ID 0x43e9 #define BRCM_PCIE_4359_DEVICE_ID 0x43ef #define BRCM_PCIE_43602_DEVICE_ID 0x43ba @@ -81,7 +84,9 @@ #define BRCM_PCIE_4366_2G_DEVICE_ID 0x43c4 #define BRCM_PCIE_4366_5G_DEVICE_ID 0x43c5 #define BRCM_PCIE_4371_DEVICE_ID 0x440d - +#define CY_PCIE_89459_DEVICE_ID 0x4415 +#define CY_PCIE_89459_RAW_DEVICE_ID 0x4355 +#define CY_PCIE_54591_DEVICE_ID 0x4417 /* brcmsmac IDs */ #define BCM4313_D11N2G_ID 0x4727 /* 4313 802.11n 2.4G device */ diff --git a/drivers/net/wireless/broadcom/brcm80211/include/brcmu_wifi.h b/drivers/net/wireless/broadcom/brcm80211/include/brcmu_wifi.h index 7b31c21..7552bdb 100644 --- a/drivers/net/wireless/broadcom/brcm80211/include/brcmu_wifi.h +++ b/drivers/net/wireless/broadcom/brcm80211/include/brcmu_wifi.h @@ -231,6 +231,8 @@ static inline bool ac_bitmap_tst(u8 bitmap, int prec) #define WPA2_AUTH_FT 0x4000 /* Fast BSS Transition */ #define WPA2_AUTH_PSK_SHA256 0x8000 /* PSK with SHA256 key derivation */ +#define WPA3_AUTH_SAE_PSK 0x40000 /* SAE with 4-way handshake */ + #define DOT11_DEFAULT_RTS_LEN 2347 #define DOT11_DEFAULT_FRAG_LEN 2346 diff --git a/drivers/net/wireless/broadcom/brcm80211/include/chipcommon.h b/drivers/net/wireless/broadcom/brcm80211/include/chipcommon.h index 0340bba..39cd34c 100644 --- a/drivers/net/wireless/broadcom/brcm80211/include/chipcommon.h +++ b/drivers/net/wireless/broadcom/brcm80211/include/chipcommon.h @@ -214,8 +214,197 @@ struct chipcregs { u32 PAD[3]; u32 retention_grpidx; /* 0x680 */ u32 retention_grpctl; /* 0x684 */ - u32 PAD[94]; - u16 sromotp[768]; + u32 mac_res_req_timer; /* 0x688 */ + u32 mac_res_req_mask; /* 0x68c */ + u32 PAD[18]; + u32 pmucontrol_ext; /* 0x6d8 */ + u32 slowclkperiod; /* 0x6dc */ + u32 PAD[8]; + u32 pmuintmask0; /* 0x700 */ + u32 pmuintmask1; /* 0x704 */ + u32 PAD[14]; + u32 pmuintstatus; /* 0x740 */ + u32 extwakeupstatus; /* 0x744 */ + u32 watchdog_res_mask; /* 0x748 */ + u32 swscratch; /* 0x750 */ + u32 PAD[3]; + u32 extwakemask[2]; /* 0x760-0x764 */ + u32 PAD[2]; + u32 extwakereqmask[2]; /* 0x770-0x774 */ + u32 PAD[2]; + u32 pmuintctrl0; /* 0x780 */ + u32 pmuintctrl1; /* 0x784 */ + u32 PAD[2]; + u32 extwakectrl[2]; /* 0x790 */ +}; + +#define CHIPGCIREGOFFS(field) offsetof(struct chipgciregs, field) + +struct chipgciregs { + u32 gci_corecaps0; /* 0x000 */ + u32 gci_corecaps1; /* 0x004 */ + u32 gci_corecaps2; /* 0x008 */ + u32 gci_corectrl; /* 0x00c */ + u32 gci_corestat; /* 0x010 */ + u32 gci_intstat; /* 0x014 */ + u32 gci_intmask; /* 0x018 */ + u32 gci_wakemask; /* 0x01c */ + u32 gci_levelintstat; /* 0x020 */ + u32 gci_eventintstat; /* 0x024 */ + u32 gci_wakelevelintstat; /* 0x028 */ + u32 gci_wakeeventintstat; /* 0x02c */ + u32 semaphoreintstatus; /* 0x030 */ + u32 semaphoreintmask; /* 0x034 */ + u32 semaphorerequest; /* 0x038 */ + u32 semaphorereserve; /* 0x03c */ + u32 gci_indirect_addr; /* 0x040 */ + u32 gci_gpioctl; /* 0x044 */ + u32 gci_gpiostatus; /* 0x048 */ + u32 gci_gpiomask; /* 0x04c */ + u32 eventsummary; /* 0x050 */ + u32 gci_miscctl; /* 0x054 */ + u32 gci_gpiointmask; /* 0x058 */ + u32 gci_gpiowakemask; /* 0x05c */ + u32 gci_input[32]; /* 0x060 */ + u32 gci_event[32]; /* 0x0e0 */ + u32 gci_output[4]; /* 0x160 */ + u32 gci_control_0; /* 0x170 */ + u32 gci_control_1; /* 0x174 */ + u32 gci_intpolreg; /* 0x178 */ + u32 gci_levelintmask; /* 0x17c */ + u32 gci_eventintmask; /* 0x180 */ + u32 wakelevelintmask; /* 0x184 */ + u32 wakeeventintmask; /* 0x188 */ + u32 hwmask; /* 0x18c */ + u32 PAD; + u32 gci_inbandeventintmask; /* 0x194 */ + u32 PAD; + u32 gci_inbandeventstatus; /* 0x19c */ + u32 gci_seciauxtx; /* 0x1a0 */ + u32 gci_seciauxrx; /* 0x1a4 */ + u32 gci_secitx_datatag; /* 0x1a8 */ + u32 gci_secirx_datatag; /* 0x1ac */ + u32 gci_secitx_datamask; /* 0x1b0 */ + u32 gci_seciusef0tx_reg; /* 0x1b4 */ + u32 gci_secif0tx_offset; /* 0x1b8 */ + u32 gci_secif0rx_offset; /* 0x1bc */ + u32 gci_secif1tx_offset; /* 0x1c0 */ + u32 gci_rxfifo_common_ctrl; /* 0x1c4 */ + u32 gci_rxfifoctrl; /* 0x1c8 */ + u32 gci_hw_sema_status; /* 0x1cc */ + u32 gci_seciuartescval; /* 0x1d0 */ + u32 gic_seciuartautobaudctr; /* 0x1d4 */ + u32 gci_secififolevel; /* 0x1d8 */ + u32 gci_seciuartdata; /* 0x1dc */ + u32 gci_secibauddiv; /* 0x1e0 */ + u32 gci_secifcr; /* 0x1e4 */ + u32 gci_secilcr; /* 0x1e8 */ + u32 gci_secimcr; /* 0x1ec */ + u32 gci_secilsr; /* 0x1f0 */ + u32 gci_secimsr; /* 0x1f4 */ + u32 gci_baudadj; /* 0x1f8 */ + u32 gci_inbandintmask; /* 0x1fc */ + u32 gci_chipctrl; /* 0x200 */ + u32 gci_chipsts; /* 0x204 */ + u32 gci_gpioout; /* 0x208 */ + u32 gci_gpioout_read; /* 0x20C */ + u32 gci_mpwaketx; /* 0x210 */ + u32 gci_mpwakedetect; /* 0x214 */ + u32 gci_seciin_ctrl; /* 0x218 */ + u32 gci_seciout_ctrl; /* 0x21C */ + u32 gci_seciin_auxfifo_en; /* 0x220 */ + u32 gci_seciout_txen_txbr; /* 0x224 */ + u32 gci_seciin_rxbrstatus; /* 0x228 */ + u32 gci_seciin_rxerrstatus; /* 0x22C */ + u32 gci_seciin_fcstatus; /* 0x230 */ + u32 gci_seciout_txstatus; /* 0x234 */ + u32 gci_seciout_txbrstatus; /* 0x238 */ + u32 wlan_mem_info; /* 0x23C */ + u32 wlan_bankxinfo; /* 0x240 */ + u32 bt_smem_select; /* 0x244 */ + u32 bt_smem_stby; /* 0x248 */ + u32 bt_smem_status; /* 0x24C */ + u32 wlan_bankxactivepda; /* 0x250 */ + u32 wlan_bankxsleeppda; /* 0x254 */ + u32 wlan_bankxkill; /* 0x258 */ + u32 PAD[41]; + u32 gci_chipid; /* 0x300 */ + u32 PAD[3]; + u32 otpstatus; /* 0x310 */ + u32 otpcontrol; /* 0x314 */ + u32 otpprog; /* 0x318 */ + u32 otplayout; /* 0x31c */ + u32 otplayoutextension; /* 0x320 */ + u32 otpcontrol1; /* 0x324 */ + u32 otpprogdata; /* 0x328 */ + u32 PAD[52]; + u32 otpECCstatus; /* 0x3FC */ + u32 PAD[512]; + u32 lhl_core_capab_adr; /* 0xC00 */ + u32 lhl_main_ctl_adr; /* 0xC04 */ + u32 lhl_pmu_ctl_adr; /* 0xC08 */ + u32 lhl_extlpo_ctl_adr; /* 0xC0C */ + u32 lpo_ctl_adr; /* 0xC10 */ + u32 lhl_lpo2_ctl_adr; /* 0xC14 */ + u32 lhl_osc32k_ctl_adr; /* 0xC18 */ + u32 lhl_clk_status_adr; /* 0xC1C */ + u32 lhl_clk_det_ctl_adr; /* 0xC20 */ + u32 lhl_clk_sel_adr; /* 0xC24 */ + u32 hidoff_cnt_adr[2]; /* 0xC28-0xC2C */ + u32 lhl_autoclk_ctl_adr; /* 0xC30 */ + u32 PAD; + u32 lhl_hibtim_adr; /* 0xC38 */ + u32 lhl_wl_ilp_val_adr; /* 0xC3C */ + u32 lhl_wl_armtim0_intrp_adr; /* 0xC40 */ + u32 lhl_wl_armtim0_st_adr; /* 0xC44 */ + u32 lhl_wl_armtim0_adr; /* 0xC48 */ + u32 PAD[9]; + u32 lhl_wl_mactim0_intrp_adr; /* 0xC70 */ + u32 lhl_wl_mactim0_st_adr; /* 0xC74 */ + u32 lhl_wl_mactim_int0_adr; /* 0xC78 */ + u32 lhl_wl_mactim_frac0_adr; /* 0xC7C */ + u32 lhl_wl_mactim1_intrp_adr; /* 0xC80 */ + u32 lhl_wl_mactim1_st_adr; /* 0xC84 */ + u32 lhl_wl_mactim_int1_adr; /* 0xC88 */ + u32 lhl_wl_mactim_frac1_adr; /* 0xC8C */ + u32 PAD[8]; + u32 gpio_int_en_port_adr[4]; /* 0xCB0-0xCBC */ + u32 gpio_int_st_port_adr[4]; /* 0xCC0-0xCCC */ + u32 gpio_ctrl_iocfg_p_adr[64]; /* 0xCD0-0xDCC */ + u32 gpio_gctrl_iocfg_p0_p39_adr; /* 0xDD0 */ + u32 gpio_gdsctrl_iocfg_p0_p25_p30_p39_adr; /* 0xDD4 */ + u32 gpio_gdsctrl_iocfg_p26_p29_adr; /* 0xDD8 */ + u32 PAD[8]; + u32 lhl_gpio_din0_adr; /* 0xDFC */ + u32 lhl_gpio_din1_adr; /* 0xE00 */ + u32 lhl_wkup_status_adr; /* 0xE04 */ + u32 lhl_ctl_adr; /* 0xE08 */ + u32 lhl_adc_ctl_adr; /* 0xE0C */ + u32 lhl_qdxyz_in_dly_adr; /* 0xE10 */ + u32 lhl_optctl_adr; /* 0xE14 */ + u32 lhl_optct2_adr; /* 0xE18 */ + u32 lhl_scanp_cntr_init_val_adr; /* 0xE1C */ + u32 lhl_opt_togg_val_adr[6]; /* 0xE20-0xE34 */ + u32 lhl_optx_smp_val_adr; /* 0xE38 */ + u32 lhl_opty_smp_val_adr; /* 0xE3C */ + u32 lhl_optz_smp_val_adr; /* 0xE40 */ + u32 lhl_hidoff_keepstate_adr[3]; /* 0xE44-0xE4C */ + u32 lhl_bt_slmboot_ctl0_adr[4]; /* 0xE50-0xE5C */ + u32 lhl_wl_fw_ctl; /* 0xE60 */ + u32 lhl_wl_hw_ctl_adr[2]; /* 0xE64-0xE68 */ + u32 lhl_bt_hw_ctl_adr; /* 0xE6C */ + u32 lhl_top_pwrseq_en_adr; /* 0xE70 */ + u32 lhl_top_pwrdn_ctl_adr; /* 0xE74 */ + u32 lhl_top_pwrup_ctl_adr; /* 0xE78 */ + u32 lhl_top_pwrseq_ctl_adr; /* 0xE7C */ + u32 lhl_top_pwrdn2_ctl_adr; /* 0xE80 */ + u32 lhl_top_pwrup2_ctl_adr; /* 0xE84 */ + u32 wpt_regon_intrp_cfg_adr; /* 0xE88 */ + u32 bt_regon_intrp_cfg_adr; /* 0xE8C */ + u32 wl_regon_intrp_cfg_adr; /* 0xE90 */ + u32 regon_intrp_st_adr; /* 0xE94 */ + u32 regon_intrp_en_adr; /* 0xE98 */ + }; /* chipid */ @@ -308,4 +497,6 @@ struct chipcregs { */ #define PMU_MAX_TRANSITION_DLY 15000 +#define DEFAULT_43012_MIN_RES_MASK 0x0f8bfe77 + #endif /* _SBCHIPC_H */ diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index ff0350c..78b6fa2 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -2,3 +2,4 @@ source "drivers/power/avs/Kconfig" source "drivers/power/reset/Kconfig" source "drivers/power/supply/Kconfig" +source "drivers/power/pwrseq/Kconfig" diff --git a/drivers/power/Makefile b/drivers/power/Makefile index b7c2e37..13046c7 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -2,3 +2,4 @@ obj-$(CONFIG_POWER_AVS) += avs/ obj-$(CONFIG_POWER_RESET) += reset/ obj-$(CONFIG_POWER_SUPPLY) += supply/ +obj-$(CONFIG_POWER_SEQUENCE) += pwrseq/ diff --git b/drivers/power/pwrseq/Kconfig b/drivers/power/pwrseq/Kconfig new file mode 100644 index 0000000..c6b3569 --- /dev/null +++ b/drivers/power/pwrseq/Kconfig @@ -0,0 +1,20 @@ +# +# Power Sequence library +# + +menuconfig POWER_SEQUENCE + bool "Power sequence control" + help + It is used for drivers which needs to do power sequence + (eg, turn on clock, toggle reset gpio) before the related + devices can be found by hardware, eg, USB bus. + +if POWER_SEQUENCE + +config PWRSEQ_GENERIC + bool "Generic power sequence control" + depends on OF + help + This is the generic power sequence control library, and is + supposed to support common power sequence usage. +endif diff --git b/drivers/power/pwrseq/Makefile b/drivers/power/pwrseq/Makefile new file mode 100644 index 0000000..ad82389 --- /dev/null +++ b/drivers/power/pwrseq/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_POWER_SEQUENCE) += core.o +obj-$(CONFIG_PWRSEQ_GENERIC) += pwrseq_generic.o diff --git b/drivers/power/pwrseq/core.c b/drivers/power/pwrseq/core.c new file mode 100644 index 0000000..3d19e62 --- /dev/null +++ b/drivers/power/pwrseq/core.c @@ -0,0 +1,335 @@ +/* + * core.c power sequence core file + * + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Author: Peter Chen + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 of + * the License as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. + */ + +#include +#include +#include +#include +#include + +static DEFINE_MUTEX(pwrseq_list_mutex); +static LIST_HEAD(pwrseq_list); + +static int pwrseq_get(struct device_node *np, struct pwrseq *p) +{ + if (p && p->get) + return p->get(np, p); + + return -ENOTSUPP; +} + +static int pwrseq_on(struct pwrseq *p) +{ + if (p && p->on) + return p->on(p); + + return -ENOTSUPP; +} + +static void pwrseq_off(struct pwrseq *p) +{ + if (p && p->off) + p->off(p); +} + +static void pwrseq_put(struct pwrseq *p) +{ + if (p && p->put) + p->put(p); +} + +/** + * pwrseq_register - Add pwrseq instance to global pwrseq list + * + * @pwrseq: the pwrseq instance + */ +void pwrseq_register(struct pwrseq *pwrseq) +{ + mutex_lock(&pwrseq_list_mutex); + list_add(&pwrseq->node, &pwrseq_list); + mutex_unlock(&pwrseq_list_mutex); +} +EXPORT_SYMBOL_GPL(pwrseq_register); + +/** + * pwrseq_unregister - Remove pwrseq instance from global pwrseq list + * + * @pwrseq: the pwrseq instance + */ +void pwrseq_unregister(struct pwrseq *pwrseq) +{ + mutex_lock(&pwrseq_list_mutex); + list_del(&pwrseq->node); + mutex_unlock(&pwrseq_list_mutex); +} +EXPORT_SYMBOL_GPL(pwrseq_unregister); + +static struct pwrseq *pwrseq_find_available_instance(struct device_node *np) +{ + struct pwrseq *pwrseq; + + mutex_lock(&pwrseq_list_mutex); + list_for_each_entry(pwrseq, &pwrseq_list, node) { + if (pwrseq->used) + continue; + + /* compare compatible string for pwrseq node */ + if (of_match_node(pwrseq->pwrseq_of_match_table, np)) { + pwrseq->used = true; + mutex_unlock(&pwrseq_list_mutex); + return pwrseq; + } + + /* return generic pwrseq instance */ + if (!strcmp(pwrseq->pwrseq_of_match_table->compatible, + "generic")) { + pr_debug("using generic pwrseq instance for %s\n", + np->full_name); + pwrseq->used = true; + mutex_unlock(&pwrseq_list_mutex); + return pwrseq; + } + } + mutex_unlock(&pwrseq_list_mutex); + pr_debug("Can't find any pwrseq instances for %s\n", np->full_name); + + return NULL; +} + +/** + * of_pwrseq_on - Carry out power sequence on for device node + * + * @np: the device node would like to power on + * + * Carry out a single device power on. If multiple devices + * need to be handled, use of_pwrseq_on_list() instead. + * + * Return a pointer to the power sequence instance on success, + * or an error code otherwise. + */ +struct pwrseq *of_pwrseq_on(struct device_node *np) +{ + struct pwrseq *pwrseq; + int ret; + + pwrseq = pwrseq_find_available_instance(np); + if (!pwrseq) + return ERR_PTR(-ENOENT); + + ret = pwrseq_get(np, pwrseq); + if (ret) { + /* Mark current pwrseq as unused */ + pwrseq->used = false; + return ERR_PTR(ret); + } + + ret = pwrseq_on(pwrseq); + if (ret) + goto pwr_put; + + return pwrseq; + +pwr_put: + pwrseq_put(pwrseq); + return ERR_PTR(ret); +} +EXPORT_SYMBOL_GPL(of_pwrseq_on); + +/** + * of_pwrseq_off - Carry out power sequence off for this pwrseq instance + * + * @pwrseq: the pwrseq instance which related device would like to be off + * + * This API is used to power off single device, it is the opposite + * operation for of_pwrseq_on. + */ +void of_pwrseq_off(struct pwrseq *pwrseq) +{ + pwrseq_off(pwrseq); + pwrseq_put(pwrseq); +} +EXPORT_SYMBOL_GPL(of_pwrseq_off); + +/** + * of_pwrseq_on_list - Carry out power sequence on for list + * + * @np: the device node would like to power on + * @head: the list head for pwrseq list on this bus + * + * This API is used to power on multiple devices at single bus. + * If there are several devices on bus (eg, USB bus), uses this + * this API. Otherwise, use of_pwrseq_on instead. After the device + * is powered on successfully, it will be added to pwrseq list for + * this bus. The caller needs to use mutex_lock for concurrent. + * + * Return 0 on success, or an error value otherwise. + */ +int of_pwrseq_on_list(struct device_node *np, struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node; + + pwrseq_list_node = kzalloc(sizeof(*pwrseq_list_node), GFP_KERNEL); + if (!pwrseq_list_node) + return -ENOMEM; + + pwrseq = of_pwrseq_on(np); + if (IS_ERR(pwrseq)) { + kfree(pwrseq_list_node); + return PTR_ERR(pwrseq); + } + + pwrseq_list_node->pwrseq = pwrseq; + list_add(&pwrseq_list_node->list, head); + + return 0; +} +EXPORT_SYMBOL_GPL(of_pwrseq_on_list); + +/** + * of_pwrseq_off_list - Carry out power sequence off for the list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to power off all devices on this bus, it is + * the opposite operation for of_pwrseq_on_list. + * The caller needs to use mutex_lock for concurrent. + */ +void of_pwrseq_off_list(struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node, *tmp_node; + + list_for_each_entry_safe(pwrseq_list_node, tmp_node, head, list) { + pwrseq = pwrseq_list_node->pwrseq; + of_pwrseq_off(pwrseq); + list_del(&pwrseq_list_node->list); + kfree(pwrseq_list_node); + } +} +EXPORT_SYMBOL_GPL(of_pwrseq_off_list); + +/** + * pwrseq_suspend - Carry out power sequence suspend for this pwrseq instance + * + * @pwrseq: the pwrseq instance + * + * This API is used to do suspend operation on pwrseq instance. + * + * Return 0 on success, or an error value otherwise. + */ +int pwrseq_suspend(struct pwrseq *p) +{ + int ret = 0; + + if (p && p->suspend) + ret = p->suspend(p); + else + return ret; + + if (!ret) + p->suspended = true; + else + pr_err("%s failed\n", __func__); + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_suspend); + +/** + * pwrseq_resume - Carry out power sequence resume for this pwrseq instance + * + * @pwrseq: the pwrseq instance + * + * This API is used to do resume operation on pwrseq instance. + * + * Return 0 on success, or an error value otherwise. + */ +int pwrseq_resume(struct pwrseq *p) +{ + int ret = 0; + + if (p && p->resume) + ret = p->resume(p); + else + return ret; + + if (!ret) + p->suspended = false; + else + pr_err("%s failed\n", __func__); + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_resume); + +/** + * pwrseq_suspend_list - Carry out power sequence suspend for list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to do suspend on all power sequence instances on this bus. + * The caller needs to use mutex_lock for concurrent. + */ +int pwrseq_suspend_list(struct list_head *head) +{ + struct pwrseq *pwrseq; + struct pwrseq_list_per_dev *pwrseq_list_node; + int ret = 0; + + list_for_each_entry(pwrseq_list_node, head, list) { + ret = pwrseq_suspend(pwrseq_list_node->pwrseq); + if (ret) + break; + } + + if (ret) { + list_for_each_entry(pwrseq_list_node, head, list) { + pwrseq = pwrseq_list_node->pwrseq; + if (pwrseq->suspended) + pwrseq_resume(pwrseq); + } + } + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_suspend_list); + +/** + * pwrseq_resume_list - Carry out power sequence resume for the list + * + * @head: the list head for pwrseq instance list on this bus + * + * This API is used to do resume on all power sequence instances on this bus. + * The caller needs to use mutex_lock for concurrent. + */ +int pwrseq_resume_list(struct list_head *head) +{ + struct pwrseq_list_per_dev *pwrseq_list_node; + int ret = 0; + + list_for_each_entry(pwrseq_list_node, head, list) { + ret = pwrseq_resume(pwrseq_list_node->pwrseq); + if (ret) + break; + } + + return ret; +} +EXPORT_SYMBOL_GPL(pwrseq_resume_list); diff --git b/drivers/power/pwrseq/pwrseq_generic.c b/drivers/power/pwrseq/pwrseq_generic.c new file mode 100644 index 0000000..4e7c090 --- /dev/null +++ b/drivers/power/pwrseq/pwrseq_generic.c @@ -0,0 +1,234 @@ +/* + * pwrseq_generic.c Generic power sequence handling + * + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * Author: Peter Chen + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 of + * the License as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +struct pwrseq_generic { + struct pwrseq pwrseq; + struct gpio_desc *gpiod_reset; + struct clk *clks[PWRSEQ_MAX_CLKS]; + u32 duration_us; + bool suspended; +}; + +#define to_generic_pwrseq(p) container_of(p, struct pwrseq_generic, pwrseq) + +static int pwrseq_generic_alloc_instance(void); +static const struct of_device_id generic_id_table[] = { + { .compatible = "generic",}, + { /* sentinel */ } +}; + +static int pwrseq_generic_suspend(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + for (clk = PWRSEQ_MAX_CLKS - 1; clk >= 0; clk--) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + pwrseq_gen->suspended = true; + return 0; +} + +static int pwrseq_generic_resume(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk, ret = 0; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS && pwrseq_gen->clks[clk]; clk++) { + ret = clk_prepare_enable(pwrseq_gen->clks[clk]); + if (ret) { + pr_err("Can't enable clock, ret=%d\n", ret); + goto err_disable_clks; + } + } + + pwrseq_gen->suspended = false; + return ret; + +err_disable_clks: + while (--clk >= 0) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + return ret; +} + +static void pwrseq_generic_put(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + if (pwrseq_gen->gpiod_reset) + gpiod_put(pwrseq_gen->gpiod_reset); + + for (clk = 0; clk < PWRSEQ_MAX_CLKS; clk++) + clk_put(pwrseq_gen->clks[clk]); + + pwrseq_unregister(&pwrseq_gen->pwrseq); + kfree(pwrseq_gen); +} + +static void pwrseq_generic_off(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk; + + if (pwrseq_gen->suspended) + return; + + for (clk = PWRSEQ_MAX_CLKS - 1; clk >= 0; clk--) + clk_disable_unprepare(pwrseq_gen->clks[clk]); +} + +static int pwrseq_generic_on(struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + int clk, ret = 0; + struct gpio_desc *gpiod_reset = pwrseq_gen->gpiod_reset; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS && pwrseq_gen->clks[clk]; clk++) { + ret = clk_prepare_enable(pwrseq_gen->clks[clk]); + if (ret) { + pr_err("Can't enable clock, ret=%d\n", ret); + goto err_disable_clks; + } + } + + if (gpiod_reset) { + u32 duration_us = pwrseq_gen->duration_us; + + if (duration_us <= 10) + udelay(10); + else + usleep_range(duration_us, duration_us + 100); + gpiod_set_value(gpiod_reset, 0); + } + + return ret; + +err_disable_clks: + while (--clk >= 0) + clk_disable_unprepare(pwrseq_gen->clks[clk]); + + return ret; +} + +static int pwrseq_generic_get(struct device_node *np, struct pwrseq *pwrseq) +{ + struct pwrseq_generic *pwrseq_gen = to_generic_pwrseq(pwrseq); + enum of_gpio_flags flags; + int reset_gpio, clk, ret = 0; + + for (clk = 0; clk < PWRSEQ_MAX_CLKS; clk++) { + pwrseq_gen->clks[clk] = of_clk_get(np, clk); + if (IS_ERR(pwrseq_gen->clks[clk])) { + ret = PTR_ERR(pwrseq_gen->clks[clk]); + if (ret != -ENOENT) + goto err_put_clks; + pwrseq_gen->clks[clk] = NULL; + break; + } + } + + reset_gpio = of_get_named_gpio_flags(np, "reset-gpios", 0, &flags); + if (gpio_is_valid(reset_gpio)) { + unsigned long gpio_flags; + + if (flags & OF_GPIO_ACTIVE_LOW) + gpio_flags = GPIOF_ACTIVE_LOW | GPIOF_OUT_INIT_LOW; + else + gpio_flags = GPIOF_OUT_INIT_HIGH; + + ret = gpio_request_one(reset_gpio, gpio_flags, + "pwrseq-reset-gpios"); + if (ret) + goto err_put_clks; + + pwrseq_gen->gpiod_reset = gpio_to_desc(reset_gpio); + of_property_read_u32(np, "reset-duration-us", + &pwrseq_gen->duration_us); + } else if (reset_gpio == -ENOENT) { + ; /* no such gpio */ + } else { + ret = reset_gpio; + pr_err("Failed to get reset gpio on %s, err = %d\n", + np->full_name, reset_gpio); + goto err_put_clks; + } + + /* allocate new one for later pwrseq instance request */ + ret = pwrseq_generic_alloc_instance(); + if (ret) + goto err_put_gpio; + + return 0; + +err_put_gpio: + if (pwrseq_gen->gpiod_reset) + gpiod_put(pwrseq_gen->gpiod_reset); +err_put_clks: + while (--clk >= 0) + clk_put(pwrseq_gen->clks[clk]); + return ret; +} + +/** + * pwrseq_generic_alloc_instance - power sequence instance allocation + * + * This function is used to allocate one generic power sequence instance, + * it is called when the system boots up and after one power sequence + * instance is got successfully. + * + * Return zero on success or an error code otherwise. + */ +static int pwrseq_generic_alloc_instance(void) +{ + struct pwrseq_generic *pwrseq_gen; + + pwrseq_gen = kzalloc(sizeof(*pwrseq_gen), GFP_KERNEL); + if (!pwrseq_gen) + return -ENOMEM; + + pwrseq_gen->pwrseq.pwrseq_of_match_table = generic_id_table; + pwrseq_gen->pwrseq.get = pwrseq_generic_get; + pwrseq_gen->pwrseq.on = pwrseq_generic_on; + pwrseq_gen->pwrseq.off = pwrseq_generic_off; + pwrseq_gen->pwrseq.put = pwrseq_generic_put; + pwrseq_gen->pwrseq.suspend = pwrseq_generic_suspend; + pwrseq_gen->pwrseq.resume = pwrseq_generic_resume; + + pwrseq_register(&pwrseq_gen->pwrseq); + return 0; +} + +/* Allocate one pwrseq instance during boots up */ +static int __init pwrseq_generic_register(void) +{ + return pwrseq_generic_alloc_instance(); +} +postcore_initcall(pwrseq_generic_register) diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig index e3a2518..bd21655 100644 --- a/drivers/pwm/Kconfig +++ b/drivers/pwm/Kconfig @@ -508,15 +508,6 @@ config PWM_TIEHRPWM To compile this driver as a module, choose M here: the module will be called pwm-tiehrpwm. -config PWM_TIPWMSS - bool - default y if (ARCH_OMAP2PLUS) && (PWM_TIECAP || PWM_TIEHRPWM) - help - PWM Subsystem driver support for AM33xx SOC. - - PWM submodules require PWM config space access from submodule - drivers and require common parent driver support. - config PWM_TWL tristate "TWL4030/6030 PWM support" depends on TWL4030_CORE diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile index 26326ad..9a47507 100644 --- a/drivers/pwm/Makefile +++ b/drivers/pwm/Makefile @@ -50,7 +50,6 @@ obj-$(CONFIG_PWM_SUN4I) += pwm-sun4i.o obj-$(CONFIG_PWM_TEGRA) += pwm-tegra.o obj-$(CONFIG_PWM_TIECAP) += pwm-tiecap.o obj-$(CONFIG_PWM_TIEHRPWM) += pwm-tiehrpwm.o -obj-$(CONFIG_PWM_TIPWMSS) += pwm-tipwmss.o obj-$(CONFIG_PWM_TWL) += pwm-twl.o obj-$(CONFIG_PWM_TWL_LED) += pwm-twl-led.o obj-$(CONFIG_PWM_VT8500) += pwm-vt8500.o diff --git a/drivers/pwm/pwm-bcm-iproc.c b/drivers/pwm/pwm-bcm-iproc.c index d392a82..1f829ed 100644 --- a/drivers/pwm/pwm-bcm-iproc.c +++ b/drivers/pwm/pwm-bcm-iproc.c @@ -85,6 +85,8 @@ static void iproc_pwmc_get_state(struct pwm_chip *chip, struct pwm_device *pwm, u64 tmp, multi, rate; u32 value, prescale; + rate = clk_get_rate(ip->clk); + value = readl(ip->base + IPROC_PWM_CTRL_OFFSET); if (value & BIT(IPROC_PWM_CTRL_EN_SHIFT(pwm->hwpwm))) @@ -97,13 +99,6 @@ static void iproc_pwmc_get_state(struct pwm_chip *chip, struct pwm_device *pwm, else state->polarity = PWM_POLARITY_INVERSED; - rate = clk_get_rate(ip->clk); - if (rate == 0) { - state->period = 0; - state->duty_cycle = 0; - return; - } - value = readl(ip->base + IPROC_PWM_PRESCALE_OFFSET); prescale = value >> IPROC_PWM_PRESCALE_SHIFT(pwm->hwpwm); prescale &= IPROC_PWM_PRESCALE_MAX; diff --git a/drivers/pwm/pwm-bcm2835.c b/drivers/pwm/pwm-bcm2835.c index d78f86f..91e24f0 100644 --- a/drivers/pwm/pwm-bcm2835.c +++ b/drivers/pwm/pwm-bcm2835.c @@ -166,7 +166,6 @@ static int bcm2835_pwm_probe(struct platform_device *pdev) pc->chip.dev = &pdev->dev; pc->chip.ops = &bcm2835_pwm_ops; - pc->chip.base = -1; pc->chip.npwm = 2; pc->chip.of_xlate = of_pwm_xlate_with_flags; pc->chip.of_pwm_n_cells = 3; diff --git a/drivers/pwm/pwm-img.c b/drivers/pwm/pwm-img.c index 599a0f6..c9e57bd 100644 --- a/drivers/pwm/pwm-img.c +++ b/drivers/pwm/pwm-img.c @@ -129,10 +129,8 @@ static int img_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, duty = DIV_ROUND_UP(timebase * duty_ns, period_ns); ret = pm_runtime_get_sync(chip->dev); - if (ret < 0) { - pm_runtime_put_autosuspend(chip->dev); + if (ret < 0) return ret; - } val = img_pwm_readl(pwm_chip, PWM_CTRL_CFG); val &= ~(PWM_CTRL_CFG_DIV_MASK << PWM_CTRL_CFG_DIV_SHIFT(pwm->hwpwm)); @@ -333,10 +331,8 @@ static int img_pwm_remove(struct platform_device *pdev) int ret; ret = pm_runtime_get_sync(&pdev->dev); - if (ret < 0) { - pm_runtime_put(&pdev->dev); + if (ret < 0) return ret; - } for (i = 0; i < pwm_chip->chip.npwm; i++) { val = img_pwm_readl(pwm_chip, PWM_CTRL_CFG); diff --git a/drivers/pwm/pwm-jz4740.c b/drivers/pwm/pwm-jz4740.c index 77c2831..9d78cc2 100644 --- a/drivers/pwm/pwm-jz4740.c +++ b/drivers/pwm/pwm-jz4740.c @@ -92,12 +92,11 @@ static int jz4740_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, { struct jz4740_pwm_chip *jz4740 = to_jz4740(pwm->chip); unsigned long long tmp; - unsigned long rate, period, duty; + unsigned long period, duty; unsigned int prescaler = 0; uint16_t ctrl; - rate = clk_get_rate(jz4740->clk); - tmp = rate * state->period; + tmp = (unsigned long long)clk_get_rate(jz4740->clk) * state->period; do_div(tmp, 1000000000); period = tmp; @@ -109,8 +108,8 @@ static int jz4740_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, if (prescaler == 6) return -EINVAL; - tmp = (unsigned long long)rate * state->duty_cycle; - do_div(tmp, NSEC_PER_SEC); + tmp = (unsigned long long)period * state->duty_cycle; + do_div(tmp, state->period); duty = period - tmp; if (duty >= period) diff --git a/drivers/pwm/pwm-rcar.c b/drivers/pwm/pwm-rcar.c index b98ec88..852eb23 100644 --- a/drivers/pwm/pwm-rcar.c +++ b/drivers/pwm/pwm-rcar.c @@ -228,28 +228,24 @@ static int rcar_pwm_probe(struct platform_device *pdev) rcar_pwm->chip.base = -1; rcar_pwm->chip.npwm = 1; - pm_runtime_enable(&pdev->dev); - ret = pwmchip_add(&rcar_pwm->chip); if (ret < 0) { dev_err(&pdev->dev, "failed to register PWM chip: %d\n", ret); - pm_runtime_disable(&pdev->dev); return ret; } + pm_runtime_enable(&pdev->dev); + return 0; } static int rcar_pwm_remove(struct platform_device *pdev) { struct rcar_pwm_chip *rcar_pwm = platform_get_drvdata(pdev); - int ret; - - ret = pwmchip_remove(&rcar_pwm->chip); pm_runtime_disable(&pdev->dev); - return ret; + return pwmchip_remove(&rcar_pwm->chip); } static const struct of_device_id rcar_pwm_of_table[] = { diff --git a/drivers/pwm/pwm-renesas-tpu.c b/drivers/pwm/pwm-renesas-tpu.c index 8032acc..4a855a2 100644 --- a/drivers/pwm/pwm-renesas-tpu.c +++ b/drivers/pwm/pwm-renesas-tpu.c @@ -415,17 +415,16 @@ static int tpu_probe(struct platform_device *pdev) tpu->chip.base = -1; tpu->chip.npwm = TPU_CHANNEL_MAX; - pm_runtime_enable(&pdev->dev); - ret = pwmchip_add(&tpu->chip); if (ret < 0) { dev_err(&pdev->dev, "failed to register PWM chip\n"); - pm_runtime_disable(&pdev->dev); return ret; } dev_info(&pdev->dev, "TPU PWM %d registered\n", tpu->pdev->id); + pm_runtime_enable(&pdev->dev); + return 0; } @@ -435,10 +434,12 @@ static int tpu_remove(struct platform_device *pdev) int ret; ret = pwmchip_remove(&tpu->chip); + if (ret) + return ret; pm_runtime_disable(&pdev->dev); - return ret; + return 0; } #ifdef CONFIG_OF diff --git a/drivers/pwm/pwm-stm32.c b/drivers/pwm/pwm-stm32.c index 359b085..7ff48c1 100644 --- a/drivers/pwm/pwm-stm32.c +++ b/drivers/pwm/pwm-stm32.c @@ -12,6 +12,7 @@ #include #include #include +#include #include #include @@ -19,6 +20,12 @@ #define CCMR_CHANNEL_MASK 0xFF #define MAX_BREAKINPUT 2 +struct stm32_breakinput { + u32 index; + u32 level; + u32 filter; +}; + struct stm32_pwm { struct pwm_chip chip; struct mutex lock; /* protect pwm config/enable */ @@ -26,15 +33,11 @@ struct stm32_pwm { struct regmap *regmap; u32 max_arr; bool have_complementary_output; + struct stm32_breakinput breakinputs[MAX_BREAKINPUT]; + unsigned int num_breakinputs; u32 capture[4] ____cacheline_aligned; /* DMA'able buffer */ }; -struct stm32_breakinput { - u32 index; - u32 level; - u32 filter; -}; - static inline struct stm32_pwm *to_stm32_pwm_dev(struct pwm_chip *chip) { return container_of(chip, struct stm32_pwm, chip); @@ -488,22 +491,19 @@ static const struct pwm_ops stm32pwm_ops = { }; static int stm32_pwm_set_breakinput(struct stm32_pwm *priv, - int index, int level, int filter) + const struct stm32_breakinput *bi) { - u32 bke = (index == 0) ? TIM_BDTR_BKE : TIM_BDTR_BK2E; - int shift = (index == 0) ? TIM_BDTR_BKF_SHIFT : TIM_BDTR_BK2F_SHIFT; - u32 mask = (index == 0) ? TIM_BDTR_BKE | TIM_BDTR_BKP | TIM_BDTR_BKF - : TIM_BDTR_BK2E | TIM_BDTR_BK2P | TIM_BDTR_BK2F; - u32 bdtr = bke; + u32 shift = TIM_BDTR_BKF_SHIFT(bi->index); + u32 bke = TIM_BDTR_BKE(bi->index); + u32 bkp = TIM_BDTR_BKP(bi->index); + u32 bkf = TIM_BDTR_BKF(bi->index); + u32 mask = bkf | bkp | bke; + u32 bdtr; - /* - * The both bits could be set since only one will be wrote - * due to mask value. - */ - if (level) - bdtr |= TIM_BDTR_BKP | TIM_BDTR_BK2P; + bdtr = (bi->filter & TIM_BDTR_BKF_MASK) << shift | bke; - bdtr |= (filter & TIM_BDTR_BKF_MASK) << shift; + if (bi->level) + bdtr |= bkp; regmap_update_bits(priv->regmap, TIM_BDTR, mask, bdtr); @@ -512,11 +512,25 @@ static int stm32_pwm_set_breakinput(struct stm32_pwm *priv, return (bdtr & bke) ? 0 : -EINVAL; } -static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv, +static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv) +{ + unsigned int i; + int ret; + + for (i = 0; i < priv->num_breakinputs; i++) { + ret = stm32_pwm_set_breakinput(priv, &priv->breakinputs[i]); + if (ret < 0) + return ret; + } + + return 0; +} + +static int stm32_pwm_probe_breakinputs(struct stm32_pwm *priv, struct device_node *np) { - struct stm32_breakinput breakinput[MAX_BREAKINPUT]; - int nb, ret, i, array_size; + int nb, ret, array_size; + unsigned int i; nb = of_property_count_elems_of_size(np, "st,breakinput", sizeof(struct stm32_breakinput)); @@ -531,20 +545,21 @@ static int stm32_pwm_apply_breakinputs(struct stm32_pwm *priv, if (nb > MAX_BREAKINPUT) return -EINVAL; + priv->num_breakinputs = nb; array_size = nb * sizeof(struct stm32_breakinput) / sizeof(u32); ret = of_property_read_u32_array(np, "st,breakinput", - (u32 *)breakinput, array_size); + (u32 *)priv->breakinputs, array_size); if (ret) return ret; - for (i = 0; i < nb && !ret; i++) { - ret = stm32_pwm_set_breakinput(priv, - breakinput[i].index, - breakinput[i].level, - breakinput[i].filter); + for (i = 0; i < priv->num_breakinputs; i++) { + if (priv->breakinputs[i].index > 1 || + priv->breakinputs[i].level > 1 || + priv->breakinputs[i].filter > 15) + return -EINVAL; } - return ret; + return stm32_pwm_apply_breakinputs(priv); } static void stm32_pwm_detect_complementary(struct stm32_pwm *priv) @@ -614,7 +629,7 @@ static int stm32_pwm_probe(struct platform_device *pdev) if (!priv->regmap || !priv->clk) return -EINVAL; - ret = stm32_pwm_apply_breakinputs(priv, np); + ret = stm32_pwm_probe_breakinputs(priv, np); if (ret) return ret; @@ -647,6 +662,42 @@ static int stm32_pwm_remove(struct platform_device *pdev) return 0; } +static int __maybe_unused stm32_pwm_suspend(struct device *dev) +{ + struct stm32_pwm *priv = dev_get_drvdata(dev); + unsigned int i; + u32 ccer, mask; + + /* Look for active channels */ + ccer = active_channels(priv); + + for (i = 0; i < priv->chip.npwm; i++) { + mask = TIM_CCER_CC1E << (i * 4); + if (ccer & mask) { + dev_err(dev, "PWM %u still in use by consumer %s\n", + i, priv->chip.pwms[i].label); + return -EBUSY; + } + } + + return pinctrl_pm_select_sleep_state(dev); +} + +static int __maybe_unused stm32_pwm_resume(struct device *dev) +{ + struct stm32_pwm *priv = dev_get_drvdata(dev); + int ret; + + ret = pinctrl_pm_select_default_state(dev); + if (ret) + return ret; + + /* restore breakinput registers that may have been lost in low power */ + return stm32_pwm_apply_breakinputs(priv); +} + +static SIMPLE_DEV_PM_OPS(stm32_pwm_pm_ops, stm32_pwm_suspend, stm32_pwm_resume); + static const struct of_device_id stm32_pwm_of_match[] = { { .compatible = "st,stm32-pwm", }, { /* end node */ }, @@ -659,6 +710,7 @@ static struct platform_driver stm32_pwm_driver = { .driver = { .name = "stm32-pwm", .of_match_table = stm32_pwm_of_match, + .pm = &stm32_pwm_pm_ops, }, }; module_platform_driver(stm32_pwm_driver); diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c index 0527372..581d232 100644 --- a/drivers/pwm/pwm-sun4i.c +++ b/drivers/pwm/pwm-sun4i.c @@ -156,7 +156,6 @@ static int sun4i_pwm_calculate(struct sun4i_pwm_chip *sun4i_pwm, if (sun4i_pwm->data->has_prescaler_bypass) { /* First, test without any prescaler when available */ prescaler = PWM_PRESCAL_MASK; - pval = 1; /* * When not using any prescaler, the clock period in nanoseconds * is not an integer so round it half up instead of diff --git a/drivers/pwm/pwm-tipwmss.c a/drivers/pwm/pwm-tipwmss.c deleted file mode 100644 index e9c26c9..0000000 --- a/drivers/pwm/pwm-tipwmss.c +++ /dev/null @@ -1,55 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * TI PWM Subsystem driver - * - * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ - */ - -#include -#include -#include -#include -#include -#include - -static const struct of_device_id pwmss_of_match[] = { - { .compatible = "ti,am33xx-pwmss" }, - {}, -}; -MODULE_DEVICE_TABLE(of, pwmss_of_match); - -static int pwmss_probe(struct platform_device *pdev) -{ - int ret; - struct device_node *node = pdev->dev.of_node; - - pm_runtime_enable(&pdev->dev); - - /* Populate all the child nodes here... */ - ret = of_platform_populate(node, NULL, NULL, &pdev->dev); - if (ret) - dev_err(&pdev->dev, "no child node found\n"); - - return ret; -} - -static int pwmss_remove(struct platform_device *pdev) -{ - pm_runtime_disable(&pdev->dev); - return 0; -} - -static struct platform_driver pwmss_driver = { - .driver = { - .name = "pwmss", - .of_match_table = pwmss_of_match, - }, - .probe = pwmss_probe, - .remove = pwmss_remove, -}; - -module_platform_driver(pwmss_driver); - -MODULE_DESCRIPTION("PWM Subsystem driver"); -MODULE_AUTHOR("Texas Instruments"); -MODULE_LICENSE("GPL"); diff --git a/drivers/regulator/twl6030-regulator.c b/drivers/regulator/twl6030-regulator.c index b8100c3..855cde0 100644 --- a/drivers/regulator/twl6030-regulator.c +++ b/drivers/regulator/twl6030-regulator.c @@ -299,6 +299,13 @@ static const struct regulator_ops twl6030fixed_ops = { .get_status = twl6030reg_get_status, }; +static struct regulator_ops twl6030_fixed_resource = { + .enable = twl6030reg_enable, + .disable = twl6030reg_disable, + .is_enabled = twl6030reg_is_enabled, + .get_status = twl6030reg_get_status, +}; + /* * SMPS status and control */ @@ -572,6 +579,19 @@ static const struct twlreg_info TWLSMPS_INFO_##label = { \ }, \ } +#define TWL6030_FIXED_RESOURCE(label, offset, turnon_delay) \ +static struct twlreg_info TWLRES_INFO_##label = { \ + .base = offset, \ + .desc = { \ + .name = #label, \ + .id = TWL6030_REG_##label, \ + .ops = &twl6030_fixed_resource, \ + .type = REGULATOR_VOLTAGE, \ + .owner = THIS_MODULE, \ + .enable_time = turnon_delay, \ + }, \ + } + /* VUSBCP is managed *only* by the USB subchip */ /* 6030 REG with base as PMC Slave Misc : 0x0030 */ /* Turnon-delay and remap configuration values for 6030 are not @@ -601,6 +621,7 @@ TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0); TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 0); TWL6030_FIXED_LDO(V1V8, 0x16, 1800, 0); TWL6030_FIXED_LDO(V2V1, 0x1c, 2100, 0); +TWL6030_FIXED_RESOURCE(CLK32KG, 0x8C, 0); TWL6032_ADJUSTABLE_SMPS(SMPS3, 0x34); TWL6032_ADJUSTABLE_SMPS(SMPS4, 0x10); TWL6032_ADJUSTABLE_SMPS(VIO, 0x16); @@ -632,6 +653,7 @@ static u8 twl_get_smps_mult(void) #define TWL6030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6030, label) #define TWL6032_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6032, label) #define TWLFIXED_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLFIXED, label) +#define TWLRES_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLRES, label) #define TWLSMPS_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLSMPS, label) static const struct of_device_id twl_of_match[] = { @@ -659,6 +681,7 @@ static const struct of_device_id twl_of_match[] = { TWLFIXED_OF_MATCH("ti,twl6030-vusb", VUSB), TWLFIXED_OF_MATCH("ti,twl6030-v1v8", V1V8), TWLFIXED_OF_MATCH("ti,twl6030-v2v1", V2V1), + TWLRES_OF_MATCH("ti,twl6030-clk32kg", CLK32KG), TWLSMPS_OF_MATCH("ti,twl6032-smps3", SMPS3), TWLSMPS_OF_MATCH("ti,twl6032-smps4", SMPS4), TWLSMPS_OF_MATCH("ti,twl6032-vio", VIO), diff --git a/drivers/spi/spidev.c b/drivers/spi/spidev.c index be503a0..bb8191d 100644 --- a/drivers/spi/spidev.c +++ b/drivers/spi/spidev.c @@ -733,9 +733,9 @@ static int spidev_probe(struct spi_device *spi) * compatible string, it is a Linux implementation thing * rather than a description of the hardware. */ - WARN(spi->dev.of_node && - of_device_is_compatible(spi->dev.of_node, "spidev"), - "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node); +// WARN(spi->dev.of_node && +// of_device_is_compatible(spi->dev.of_node, "spidev"), +// "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node); spidev_probe_acpi(spi); diff --git a/drivers/staging/exfat/Kconfig b/drivers/staging/exfat/Kconfig index ce32dfe..292a19d 100644 --- a/drivers/staging/exfat/Kconfig +++ b/drivers/staging/exfat/Kconfig @@ -1,50 +1,41 @@ # SPDX-License-Identifier: GPL-2.0 -config EXFAT_FS +config STAGING_EXFAT_FS tristate "exFAT fs support" depends on BLOCK select NLS help This adds support for the exFAT file system. -config EXFAT_DONT_MOUNT_VFAT - bool "Prohibit mounting of fat/vfat filesystems by exFAT" - depends on EXFAT_FS - default y - help - By default, the exFAT driver will only mount exFAT filesystems, and refuse - to mount fat/vfat filesystems. Set this to 'n' to allow the exFAT driver - to mount these filesystems. - -config EXFAT_DISCARD +config STAGING_EXFAT_DISCARD bool "enable discard support" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default y -config EXFAT_DELAYED_SYNC +config STAGING_EXFAT_DELAYED_SYNC bool "enable delayed sync" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_KERNEL_DEBUG +config STAGING_EXFAT_KERNEL_DEBUG bool "enable kernel debug features via ioctl" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_DEBUG_MSG +config STAGING_EXFAT_DEBUG_MSG bool "print debug messages" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS default n -config EXFAT_DEFAULT_CODEPAGE +config STAGING_EXFAT_DEFAULT_CODEPAGE int "Default codepage for exFAT" default 437 - depends on EXFAT_FS + depends on STAGING_EXFAT_FS help This option should be set to the codepage of your exFAT filesystems. -config EXFAT_DEFAULT_IOCHARSET +config STAGING_EXFAT_DEFAULT_IOCHARSET string "Default iocharset for exFAT" default "utf8" - depends on EXFAT_FS + depends on STAGING_EXFAT_FS help Set this to the default input/output character set you'd like exFAT to use. diff --git a/drivers/staging/exfat/Makefile b/drivers/staging/exfat/Makefile index 6c90aec..057556e 100644 --- a/drivers/staging/exfat/Makefile +++ b/drivers/staging/exfat/Makefile @@ -1,6 +1,6 @@ # SPDX-License-Identifier: GPL-2.0-or-later -obj-$(CONFIG_EXFAT_FS) += exfat.o +obj-$(CONFIG_STAGING_EXFAT_FS) += exfat.o exfat-y := exfat_core.o \ exfat_super.o \ diff --git a/drivers/staging/exfat/TODO b/drivers/staging/exfat/TODO index a3eb282..a283ce5 100644 --- a/drivers/staging/exfat/TODO +++ b/drivers/staging/exfat/TODO @@ -1,8 +1,22 @@ +A laundry list of things that need looking at, most of which will +require more work than the average checkpatch cleanup... + +Note that some of these entries may not be bugs - they're things +that need to be looked at, and *possibly* fixed. + +Clean up the ffsCamelCase function names. + +Fix (thing)->flags to not use magic numbers - multiple offenders + +Sort out all the s32/u32/u8 nonsense - most of these should be plain int. + exfat_core.c - ffsReadFile - the goto err_out seem to leak a brelse(). same for ffsWriteFile. -exfat_core.c - fs_sync(sb,0) all over the place looks fishy as hell. -There's only one place that calls it with a non-zero argument. +All the calls to fs_sync() need to be looked at, particularly in the +context of EXFAT_DELAYED_SYNC. Currently, if that's defined, we only +flush to disk when sync() gets called. We should be doing at least +metadata flushes at appropriate times. ffsTruncateFile - if (old_size <= new_size) { That doesn't look right. How did it ever work? Are they relying on lazy @@ -10,3 +24,46 @@ block allocation when actual writes happen? If nothing else, it never does the 'fid->size = new_size' and do the inode update.... ffsSetAttr() is just dangling in the breeze, not wired up at all... + +Convert global mutexes to a per-superblock mutex. + +Right now, we load exactly one UTF-8 table. Check to see +if that plays nice with different codepage and iocharset values +for simultanous mounts of different devices + +exfat_rmdir() checks for -EBUSY but ffsRemoveDir() doesn't return it. +In fact, there's a complete lack of -EBUSY testing anywhere. + +There's probably a few missing checks for -EEXIST + +check return codes of sync_dirty_buffer() + +Why is remove_file doing a num_entries++?? + +Double check a lot of can't-happen parameter checks (for null pointers for +things that have only one call site and can't pass a null, etc). + +All the DEBUG stuff can probably be tossed, including the ioctl(). Either +that, or convert to a proper fault-injection system. + +exfat_remount does exactly one thing. Fix to actually deal with remount +options, particularly handling R/O correctly. For that matter, allow +R/O mounts in the first place. + +Figure out why the VFAT code used multi_sector_(read|write) but the +exfat code doesn't use it. The difference matters on SSDs with wear leveling. + +exfat_fat_sync(), exfat_buf_sync(), and sync_alloc_bitmap() +aren't called anyplace.... + +Create helper function for exfat_set_entry_time() and exfat_set_entry_type() +because it's sort of ugly to be calling the same functionn directly and +other code calling through the fs_func struc ponters... + +clean up the remaining vol_type checks, which are of two types: +some are ?: operators with magic numbers, and the rest are places +where we're doing stuff with '.' and '..'. + +Patches to: + Greg Kroah-Hartman + Valdis Kletnieks diff --git a/drivers/staging/exfat/exfat.h b/drivers/staging/exfat/exfat.h index 4973c9e..4d87360 100644 --- a/drivers/staging/exfat/exfat.h +++ b/drivers/staging/exfat/exfat.h @@ -9,7 +9,7 @@ #include #include -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG /* For Debugging Purpose */ /* IOCTL code 'f' used by * - file systems typically #0~0x1F @@ -22,14 +22,16 @@ #define EXFAT_DEBUGFLAGS_INVALID_UMOUNT 0x01 #define EXFAT_DEBUGFLAGS_ERROR_RW 0x02 -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ -#ifdef CONFIG_EXFAT_DEBUG_MSG +#ifdef CONFIG_STAGING_EXFAT_DEBUG_MSG #define DEBUG 1 #else #undef DEBUG #endif +#define EFSCORRUPTED EUCLEAN /* Filesystem is corrupted */ + #define DENTRY_SIZE 32 /* dir entry size */ #define DENTRY_SIZE_BITS 5 @@ -206,28 +208,6 @@ static inline u16 get_row_index(u16 i) #define FM_REGULAR 0x00 #define FM_SYMLINK 0x40 -/* return values */ -#define FFS_SUCCESS 0 -#define FFS_MEDIAERR 1 -#define FFS_FORMATERR 2 -#define FFS_MOUNTED 3 -#define FFS_NOTMOUNTED 4 -#define FFS_ALIGNMENTERR 5 -#define FFS_SEMAPHOREERR 6 -#define FFS_INVALIDPATH 7 -#define FFS_INVALIDFID 8 -#define FFS_NOTFOUND 9 -#define FFS_FILEEXIST 10 -#define FFS_PERMISSIONERR 11 -#define FFS_NOTOPENED 12 -#define FFS_MAXOPENED 13 -#define FFS_FULL 14 -#define FFS_EOF 15 -#define FFS_DIRBUSY 16 -#define FFS_MEMORYERR 17 -#define FFS_NAMETOOLONG 18 -#define FFS_ERROR 19 - #define NUM_UPCASE 2918 #define DOS_CUR_DIR_NAME ". " @@ -536,49 +516,6 @@ struct buf_cache_t { struct buffer_head *buf_bh; }; -struct fs_func { - s32 (*alloc_cluster)(struct super_block *sb, s32 num_alloc, - struct chain_t *p_chain); - void (*free_cluster)(struct super_block *sb, struct chain_t *p_chain, - s32 do_relse); - s32 (*count_used_clusters)(struct super_block *sb); - - s32 (*init_dir_entry)(struct super_block *sb, struct chain_t *p_dir, - s32 entry, u32 type, u32 start_clu, u64 size); - s32 (*init_ext_entry)(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 num_entries, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname); - s32 (*find_dir_entry)(struct super_block *sb, struct chain_t *p_dir, - struct uni_name_t *p_uniname, s32 num_entries, - struct dos_name_t *p_dosname, u32 type); - void (*delete_dir_entry)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - s32 offset, s32 num_entries); - void (*get_uni_name_from_ext_entry)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - u16 *uniname); - s32 (*count_ext_entries)(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - struct dentry_t *p_entry); - s32 (*calc_num_entries)(struct uni_name_t *p_uniname); - - u32 (*get_entry_type)(struct dentry_t *p_entry); - void (*set_entry_type)(struct dentry_t *p_entry, u32 type); - u32 (*get_entry_attr)(struct dentry_t *p_entry); - void (*set_entry_attr)(struct dentry_t *p_entry, u32 attr); - u8 (*get_entry_flag)(struct dentry_t *p_entry); - void (*set_entry_flag)(struct dentry_t *p_entry, u8 flag); - u32 (*get_entry_clu0)(struct dentry_t *p_entry); - void (*set_entry_clu0)(struct dentry_t *p_entry, u32 clu0); - u64 (*get_entry_size)(struct dentry_t *p_entry); - void (*set_entry_size)(struct dentry_t *p_entry, u64 size); - void (*get_entry_time)(struct dentry_t *p_entry, - struct timestamp_t *tp, u8 mode); - void (*set_entry_time)(struct dentry_t *p_entry, - struct timestamp_t *tp, u8 mode); -}; - struct fs_info_t { u32 drv; /* drive ID */ u32 vol_type; /* volume FAT type */ @@ -617,8 +554,7 @@ struct fs_info_t { u32 dev_ejected; /* block device operation error flag */ - struct fs_func *fs_func; - struct semaphore v_sem; + struct mutex v_mutex; /* FAT cache */ struct buf_cache_t FAT_cache_array[FAT_CACHE_SIZE]; @@ -681,10 +617,10 @@ struct exfat_mount_options { /* on error: continue, panic, remount-ro */ unsigned char errors; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD /* flag on if -o dicard specified and device support discard() */ unsigned char discard; -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ }; #define EXFAT_HASH_BITS 8 @@ -720,9 +656,9 @@ struct exfat_sb_info { spinlock_t inode_hash_lock; struct hlist_head inode_hashtable[EXFAT_HASH_SIZE]; -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG long debug_flags; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ }; /* @@ -749,14 +685,7 @@ static inline struct exfat_inode_info *EXFAT_I(struct inode *inode) /* NLS management function */ u16 nls_upper(struct super_block *sb, u16 a); -int nls_dosname_cmp(struct super_block *sb, u8 *a, u8 *b); int nls_uniname_cmp(struct super_block *sb, u16 *a, u16 *b); -void nls_uniname_to_dosname(struct super_block *sb, - struct dos_name_t *p_dosname, - struct uni_name_t *p_uniname, bool *p_lossy); -void nls_dosname_to_uniname(struct super_block *sb, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname); void nls_uniname_to_cstring(struct super_block *sb, u8 *p_cstring, struct uni_name_t *p_uniname); void nls_cstring_to_uniname(struct super_block *sb, @@ -764,48 +693,33 @@ void nls_cstring_to_uniname(struct super_block *sb, bool *p_lossy); /* buffer cache management */ -void buf_init(struct super_block *sb); -void buf_shutdown(struct super_block *sb); -int FAT_read(struct super_block *sb, u32 loc, u32 *content); -s32 FAT_write(struct super_block *sb, u32 loc, u32 content); -u8 *FAT_getblk(struct super_block *sb, sector_t sec); -void FAT_modify(struct super_block *sb, sector_t sec); -void FAT_release_all(struct super_block *sb); -void FAT_sync(struct super_block *sb); -u8 *buf_getblk(struct super_block *sb, sector_t sec); -void buf_modify(struct super_block *sb, sector_t sec); -void buf_lock(struct super_block *sb, sector_t sec); -void buf_unlock(struct super_block *sb, sector_t sec); -void buf_release(struct super_block *sb, sector_t sec); -void buf_release_all(struct super_block *sb); -void buf_sync(struct super_block *sb); +void exfat_buf_init(struct super_block *sb); +void exfat_buf_shutdown(struct super_block *sb); +int exfat_fat_read(struct super_block *sb, u32 loc, u32 *content); +s32 exfat_fat_write(struct super_block *sb, u32 loc, u32 content); +u8 *exfat_fat_getblk(struct super_block *sb, sector_t sec); +void exfat_fat_modify(struct super_block *sb, sector_t sec); +void exfat_fat_release_all(struct super_block *sb); +void exfat_fat_sync(struct super_block *sb); +u8 *exfat_buf_getblk(struct super_block *sb, sector_t sec); +void exfat_buf_modify(struct super_block *sb, sector_t sec); +void exfat_buf_lock(struct super_block *sb, sector_t sec); +void exfat_buf_unlock(struct super_block *sb, sector_t sec); +void exfat_buf_release(struct super_block *sb, sector_t sec); +void exfat_buf_release_all(struct super_block *sb); +void exfat_buf_sync(struct super_block *sb); /* fs management functions */ void fs_set_vol_flags(struct super_block *sb, u32 new_flag); void fs_error(struct super_block *sb); /* cluster management functions */ -s32 clear_cluster(struct super_block *sb, u32 clu); -s32 fat_alloc_cluster(struct super_block *sb, s32 num_alloc, - struct chain_t *p_chain); -s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, - struct chain_t *p_chain); -void fat_free_cluster(struct super_block *sb, struct chain_t *p_chain, - s32 do_relse); -void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, - s32 do_relse); -u32 find_last_cluster(struct super_block *sb, struct chain_t *p_chain); s32 count_num_clusters(struct super_block *sb, struct chain_t *dir); -s32 fat_count_used_clusters(struct super_block *sb); -s32 exfat_count_used_clusters(struct super_block *sb); void exfat_chain_cont_cluster(struct super_block *sb, u32 chain, s32 len); /* allocation bitmap management functions */ s32 load_alloc_bitmap(struct super_block *sb); void free_alloc_bitmap(struct super_block *sb); -s32 set_alloc_bitmap(struct super_block *sb, u32 clu); -s32 clr_alloc_bitmap(struct super_block *sb, u32 clu); -u32 test_alloc_bitmap(struct super_block *sb, u32 clu); void sync_alloc_bitmap(struct super_block *sb); /* upcase table management functions */ @@ -813,63 +727,8 @@ s32 load_upcase_table(struct super_block *sb); void free_upcase_table(struct super_block *sb); /* dir entry management functions */ -u32 fat_get_entry_type(struct dentry_t *p_entry); -u32 exfat_get_entry_type(struct dentry_t *p_entry); -void fat_set_entry_type(struct dentry_t *p_entry, u32 type); -void exfat_set_entry_type(struct dentry_t *p_entry, u32 type); -u32 fat_get_entry_attr(struct dentry_t *p_entry); -u32 exfat_get_entry_attr(struct dentry_t *p_entry); -void fat_set_entry_attr(struct dentry_t *p_entry, u32 attr); -void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr); -u8 fat_get_entry_flag(struct dentry_t *p_entry); -u8 exfat_get_entry_flag(struct dentry_t *p_entry); -void fat_set_entry_flag(struct dentry_t *p_entry, u8 flag); -void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flag); -u32 fat_get_entry_clu0(struct dentry_t *p_entry); -u32 exfat_get_entry_clu0(struct dentry_t *p_entry); -void fat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu); -void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu); -u64 fat_get_entry_size(struct dentry_t *p_entry); -u64 exfat_get_entry_size(struct dentry_t *p_entry); -void fat_set_entry_size(struct dentry_t *p_entry, u64 size); -void exfat_set_entry_size(struct dentry_t *p_entry, u64 size); struct timestamp_t *tm_current(struct timestamp_t *tm); -void fat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode); -void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode); -void fat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode); -void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode); -s32 fat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, s32 entry, - u32 type, u32 start_clu, u64 size); -s32 exfat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, u32 type, u32 start_clu, u64 size); -s32 fat_init_ext_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 num_entries, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname); -s32 exfat_init_ext_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 num_entries, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname); -void init_dos_entry(struct dos_dentry_t *ep, u32 type, u32 start_clu); -void init_ext_entry(struct ext_dentry_t *ep, s32 order, u8 chksum, - u16 *uniname); -void init_file_entry(struct file_dentry_t *ep, u32 type); -void init_strm_entry(struct strm_dentry_t *ep, u8 flags, u32 start_clu, - u64 size); -void init_name_entry(struct name_dentry_t *ep, u16 *uniname); -void fat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 order, s32 num_entries); -void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 order, s32 num_entries); -s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, - sector_t *sector, s32 *offset); -struct dentry_t *get_entry_with_sector(struct super_block *sb, sector_t sector, - s32 offset); struct dentry_t *get_entry_in_dir(struct super_block *sb, struct chain_t *p_dir, s32 entry, sector_t *sector); struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, @@ -877,24 +736,6 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, u32 type, struct dentry_t **file_ep); void release_entry_set(struct entry_set_cache_t *es); -s32 write_whole_entry_set(struct super_block *sb, struct entry_set_cache_t *es); -s32 write_partial_entries_in_entry_set(struct super_block *sb, - struct entry_set_cache_t *es, - struct dentry_t *ep, u32 count); -s32 search_deleted_or_unused_entry(struct super_block *sb, - struct chain_t *p_dir, s32 num_entries); -s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, - s32 num_entries); -s32 fat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, - struct uni_name_t *p_uniname, s32 num_entries, - struct dos_name_t *p_dosname, u32 type); -s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, - struct uni_name_t *p_uniname, s32 num_entries, - struct dos_name_t *p_dosname, u32 type); -s32 fat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, - s32 entry, struct dentry_t *p_entry); -s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, - s32 entry, struct dentry_t *p_entry); s32 count_dos_name_entries(struct super_block *sb, struct chain_t *p_dir, u32 type); void update_dir_checksum(struct super_block *sb, struct chain_t *p_dir, @@ -907,36 +748,13 @@ bool is_dir_empty(struct super_block *sb, struct chain_t *p_dir); s32 get_num_entries_and_dos_name(struct super_block *sb, struct chain_t *p_dir, struct uni_name_t *p_uniname, s32 *entries, struct dos_name_t *p_dosname); -void get_uni_name_from_dos_entry(struct super_block *sb, - struct dos_dentry_t *ep, - struct uni_name_t *p_uniname, u8 mode); -void fat_get_uni_name_from_ext_entry(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - u16 *uniname); -void exfat_get_uni_name_from_ext_entry(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - u16 *uniname); -s32 extract_uni_name_from_ext_entry(struct ext_dentry_t *ep, - u16 *uniname, s32 order); -s32 extract_uni_name_from_name_entry(struct name_dentry_t *ep, - u16 *uniname, s32 order); -s32 fat_generate_dos_name(struct super_block *sb, struct chain_t *p_dir, - struct dos_name_t *p_dosname); -void fat_attach_count_to_dos_name(u8 *dosname, s32 count); -s32 fat_calc_num_entries(struct uni_name_t *p_uniname); -s32 exfat_calc_num_entries(struct uni_name_t *p_uniname); -u8 calc_checksum_1byte(void *data, s32 len, u8 chksum); u16 calc_checksum_2byte(void *data, s32 len, u16 chksum, s32 type); -u32 calc_checksum_4byte(void *data, s32 len, u32 chksum, s32 type); /* name resolution functions */ s32 resolve_path(struct inode *inode, char *path, struct chain_t *p_dir, struct uni_name_t *p_uniname); -s32 resolve_name(u8 *name, u8 **arg); /* file operation functions */ -s32 fat16_mount(struct super_block *sb, struct pbr_sector_t *p_pbr); -s32 fat32_mount(struct super_block *sb, struct pbr_sector_t *p_pbr); s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr); s32 create_dir(struct inode *inode, struct chain_t *p_dir, struct uni_name_t *p_uniname, struct file_id_t *fid); @@ -959,13 +777,48 @@ int multi_sector_read(struct super_block *sb, sector_t sec, int multi_sector_write(struct super_block *sb, sector_t sec, struct buffer_head *bh, s32 num_secs, bool sync); -void bdev_open(struct super_block *sb); -void bdev_close(struct super_block *sb); -int bdev_read(struct super_block *sb, sector_t secno, +void exfat_bdev_open(struct super_block *sb); +void exfat_bdev_close(struct super_block *sb); +int exfat_bdev_read(struct super_block *sb, sector_t secno, struct buffer_head **bh, u32 num_secs, bool read); -int bdev_write(struct super_block *sb, sector_t secno, +int exfat_bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, u32 num_secs, bool sync); -int bdev_sync(struct super_block *sb); +int exfat_bdev_sync(struct super_block *sb); + +/* cluster operation functions */ +s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, + struct chain_t *p_chain); +void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, + s32 do_relse); +s32 exfat_count_used_clusters(struct super_block *sb); + +/* dir operation functions */ +s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, + struct uni_name_t *p_uniname, s32 num_entries, + struct dos_name_t *p_dosname, u32 type); +void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, + s32 entry, s32 order, s32 num_entries); +void exfat_get_uni_name_from_ext_entry(struct super_block *sb, + struct chain_t *p_dir, s32 entry, + u16 *uniname); +s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, + s32 entry, struct dentry_t *p_entry); +s32 exfat_calc_num_entries(struct uni_name_t *p_uniname); + +/* dir entry getter/setter */ +u32 exfat_get_entry_type(struct dentry_t *p_entry); +u32 exfat_get_entry_attr(struct dentry_t *p_entry); +void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr); +u8 exfat_get_entry_flag(struct dentry_t *p_entry); +void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags); +u32 exfat_get_entry_clu0(struct dentry_t *p_entry); +void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu); +u64 exfat_get_entry_size(struct dentry_t *p_entry); +void exfat_set_entry_size(struct dentry_t *p_entry, u64 size); +void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, + u8 mode); +void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, + u8 mode); extern const u8 uni_upcase[]; #endif /* _EXFAT_H */ diff --git a/drivers/staging/exfat/exfat_blkdev.c b/drivers/staging/exfat/exfat_blkdev.c index 81d20e6..0a3dc35 100644 --- a/drivers/staging/exfat/exfat_blkdev.c +++ b/drivers/staging/exfat/exfat_blkdev.c @@ -8,7 +8,7 @@ #include #include "exfat.h" -void bdev_open(struct super_block *sb) +void exfat_bdev_open(struct super_block *sb) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); @@ -23,28 +23,28 @@ void bdev_open(struct super_block *sb) p_bd->opened = true; } -void bdev_close(struct super_block *sb) +void exfat_bdev_close(struct super_block *sb) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); p_bd->opened = false; } -int bdev_read(struct super_block *sb, sector_t secno, struct buffer_head **bh, - u32 num_secs, bool read) +int exfat_bdev_read(struct super_block *sb, sector_t secno, struct buffer_head **bh, + u32 num_secs, bool read) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) - return FFS_MEDIAERR; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ + return -EIO; +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) - return FFS_MEDIAERR; + return -ENODEV; if (*bh) __brelse(*bh); @@ -62,26 +62,26 @@ int bdev_read(struct super_block *sb, sector_t secno, struct buffer_head **bh, WARN(!p_fs->dev_ejected, "[EXFAT] No bh, device seems wrong or to be ejected.\n"); - return FFS_MEDIAERR; + return -EIO; } -int bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, - u32 num_secs, bool sync) +int exfat_bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, + u32 num_secs, bool sync) { s32 count; struct buffer_head *bh2; struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) - return FFS_MEDIAERR; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ + return -EIO; +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) - return FFS_MEDIAERR; + return -ENODEV; if (secno == bh->b_blocknr) { lock_buffer(bh); @@ -89,7 +89,7 @@ int bdev_write(struct super_block *sb, sector_t secno, struct buffer_head *bh, mark_buffer_dirty(bh); unlock_buffer(bh); if (sync && (sync_dirty_buffer(bh) != 0)) - return FFS_MEDIAERR; + return -EIO; } else { count = num_secs << p_bd->sector_size_bits; @@ -115,22 +115,22 @@ no_bh: WARN(!p_fs->dev_ejected, "[EXFAT] No bh, device seems wrong or to be ejected.\n"); - return FFS_MEDIAERR; + return -EIO; } -int bdev_sync(struct super_block *sb) +int exfat_bdev_sync(struct super_block *sb) { struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG struct exfat_sb_info *sbi = EXFAT_SB(sb); long flags = sbi->debug_flags; if (flags & EXFAT_DEBUGFLAGS_ERROR_RW) - return FFS_MEDIAERR; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ + return -EIO; +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ if (!p_bd->opened) - return FFS_MEDIAERR; + return -ENODEV; return sync_blockdev(sb->s_bdev); } diff --git a/drivers/staging/exfat/exfat_cache.c b/drivers/staging/exfat/exfat_cache.c index e1b0017..3fd5604 100644 --- a/drivers/staging/exfat/exfat_cache.c +++ b/drivers/staging/exfat/exfat_cache.c @@ -12,8 +12,8 @@ #define DIRTYBIT 0x02 /* Local variables */ -static DEFINE_SEMAPHORE(f_sem); -static DEFINE_SEMAPHORE(b_sem); +static DEFINE_MUTEX(f_mutex); +static DEFINE_MUTEX(b_mutex); static struct buf_cache_t *FAT_cache_find(struct super_block *sb, sector_t sec) { @@ -128,7 +128,7 @@ static void buf_cache_remove_hash(struct buf_cache_t *bp) (bp->hash_next)->hash_prev = bp->hash_prev; } -void buf_init(struct super_block *sb) +void exfat_buf_init(struct super_block *sb) { struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); @@ -189,11 +189,11 @@ void buf_init(struct super_block *sb) buf_cache_insert_hash(sb, &p_fs->buf_cache_array[i]); } -void buf_shutdown(struct super_block *sb) +void exfat_buf_shutdown(struct super_block *sb) { } -static int __FAT_read(struct super_block *sb, u32 loc, u32 *content) +static int __exfat_fat_read(struct super_block *sb, u32 loc, u32 *content) { s32 off; u32 _content; @@ -202,107 +202,22 @@ static int __FAT_read(struct super_block *sb, u32 loc, u32 *content) struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - if (p_fs->vol_type == FAT12) { - sec = p_fs->FAT1_start_sector + - ((loc + (loc >> 1)) >> p_bd->sector_size_bits); - off = (loc + (loc >> 1)) & p_bd->sector_size_mask; + sec = p_fs->FAT1_start_sector + + (loc >> (p_bd->sector_size_bits - 2)); + off = (loc << 2) & p_bd->sector_size_mask; - if (off == (p_bd->sector_size - 1)) { - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; + fat_sector = exfat_fat_getblk(sb, sec); + if (!fat_sector) + return -1; - _content = (u32)fat_sector[off]; + fat_entry = &fat_sector[off]; + _content = GET32_A(fat_entry); - fat_sector = FAT_getblk(sb, ++sec); - if (!fat_sector) - return -1; - - _content |= (u32)fat_sector[0] << 8; - } else { - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - _content = GET16(fat_entry); - } - - if (loc & 1) - _content >>= 4; - - _content &= 0x00000FFF; - - if (_content >= CLUSTER_16(0x0FF8)) { - *content = CLUSTER_32(~0); - return 0; - } - *content = CLUSTER_32(_content); - return 0; - } else if (p_fs->vol_type == FAT16) { - sec = p_fs->FAT1_start_sector + - (loc >> (p_bd->sector_size_bits - 1)); - off = (loc << 1) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - - _content = GET16_A(fat_entry); - - _content &= 0x0000FFFF; - - if (_content >= CLUSTER_16(0xFFF8)) { - *content = CLUSTER_32(~0); - return 0; - } - *content = CLUSTER_32(_content); - return 0; - } else if (p_fs->vol_type == FAT32) { - sec = p_fs->FAT1_start_sector + - (loc >> (p_bd->sector_size_bits - 2)); - off = (loc << 2) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - - _content = GET32_A(fat_entry); - - _content &= 0x0FFFFFFF; - - if (_content >= CLUSTER_32(0x0FFFFFF8)) { - *content = CLUSTER_32(~0); - return 0; - } - *content = CLUSTER_32(_content); - return 0; - } else if (p_fs->vol_type == EXFAT) { - sec = p_fs->FAT1_start_sector + - (loc >> (p_bd->sector_size_bits - 2)); - off = (loc << 2) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - _content = GET32_A(fat_entry); - - if (_content >= CLUSTER_32(0xFFFFFFF8)) { - *content = CLUSTER_32(~0); - return 0; - } - *content = CLUSTER_32(_content); + if (_content >= CLUSTER_32(0xFFFFFFF8)) { + *content = CLUSTER_32(~0); return 0; } - - /* Unknown volume type, throw in the towel and go home */ - *content = CLUSTER_32(~0); + *content = CLUSTER_32(_content); return 0; } @@ -311,18 +226,18 @@ static int __FAT_read(struct super_block *sb, u32 loc, u32 *content) * returns 0 on success * -1 on error */ -int FAT_read(struct super_block *sb, u32 loc, u32 *content) +int exfat_fat_read(struct super_block *sb, u32 loc, u32 *content) { s32 ret; - down(&f_sem); - ret = __FAT_read(sb, loc, content); - up(&f_sem); + mutex_lock(&f_mutex); + ret = __exfat_fat_read(sb, loc, content); + mutex_unlock(&f_mutex); return ret; } -static s32 __FAT_write(struct super_block *sb, u32 loc, u32 content) +static s32 __exfat_fat_write(struct super_block *sb, u32 loc, u32 content) { s32 off; sector_t sec; @@ -330,118 +245,34 @@ static s32 __FAT_write(struct super_block *sb, u32 loc, u32 content) struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - if (p_fs->vol_type == FAT12) { - content &= 0x00000FFF; - - sec = p_fs->FAT1_start_sector + - ((loc + (loc >> 1)) >> p_bd->sector_size_bits); - off = (loc + (loc >> 1)) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - if (loc & 1) { /* odd */ - content <<= 4; - - if (off == (p_bd->sector_size - 1)) { - fat_sector[off] = (u8)(content | - (fat_sector[off] & - 0x0F)); - FAT_modify(sb, sec); - - fat_sector = FAT_getblk(sb, ++sec); - if (!fat_sector) - return -1; - - fat_sector[0] = (u8)(content >> 8); - } else { - fat_entry = &fat_sector[off]; - content |= GET16(fat_entry) & 0x000F; - - SET16(fat_entry, content); - } - } else { /* even */ - fat_sector[off] = (u8)(content); - - if (off == (p_bd->sector_size - 1)) { - fat_sector[off] = (u8)(content); - FAT_modify(sb, sec); - - fat_sector = FAT_getblk(sb, ++sec); - if (!fat_sector) - return -1; - fat_sector[0] = (u8)((fat_sector[0] & 0xF0) | - (content >> 8)); - } else { - fat_entry = &fat_sector[off]; - content |= GET16(fat_entry) & 0xF000; - - SET16(fat_entry, content); - } - } - } - - else if (p_fs->vol_type == FAT16) { - content &= 0x0000FFFF; - - sec = p_fs->FAT1_start_sector + (loc >> - (p_bd->sector_size_bits - 1)); - off = (loc << 1) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - - SET16_A(fat_entry, content); - } else if (p_fs->vol_type == FAT32) { - content &= 0x0FFFFFFF; + sec = p_fs->FAT1_start_sector + (loc >> + (p_bd->sector_size_bits - 2)); + off = (loc << 2) & p_bd->sector_size_mask; - sec = p_fs->FAT1_start_sector + (loc >> - (p_bd->sector_size_bits - 2)); - off = (loc << 2) & p_bd->sector_size_mask; + fat_sector = exfat_fat_getblk(sb, sec); + if (!fat_sector) + return -1; - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; + fat_entry = &fat_sector[off]; - fat_entry = &fat_sector[off]; - - content |= GET32_A(fat_entry) & 0xF0000000; - - SET32_A(fat_entry, content); - } else { /* p_fs->vol_type == EXFAT */ - sec = p_fs->FAT1_start_sector + (loc >> - (p_bd->sector_size_bits - 2)); - off = (loc << 2) & p_bd->sector_size_mask; - - fat_sector = FAT_getblk(sb, sec); - if (!fat_sector) - return -1; - - fat_entry = &fat_sector[off]; - - SET32_A(fat_entry, content); - } + SET32_A(fat_entry, content); - FAT_modify(sb, sec); + exfat_fat_modify(sb, sec); return 0; } -int FAT_write(struct super_block *sb, u32 loc, u32 content) +int exfat_fat_write(struct super_block *sb, u32 loc, u32 content) { s32 ret; - down(&f_sem); - ret = __FAT_write(sb, loc, content); - up(&f_sem); + mutex_lock(&f_mutex); + ret = __exfat_fat_write(sb, loc, content); + mutex_unlock(&f_mutex); return ret; } -u8 *FAT_getblk(struct super_block *sb, sector_t sec) +u8 *exfat_fat_getblk(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); @@ -462,7 +293,7 @@ u8 *FAT_getblk(struct super_block *sb, sector_t sec) FAT_cache_insert_hash(sb, bp); - if (sector_read(sb, sec, &bp->buf_bh, 1) != FFS_SUCCESS) { + if (sector_read(sb, sec, &bp->buf_bh, 1) != 0) { FAT_cache_remove_hash(bp); bp->drv = -1; bp->sec = ~0; @@ -476,7 +307,7 @@ u8 *FAT_getblk(struct super_block *sb, sector_t sec) return bp->buf_bh->b_data; } -void FAT_modify(struct super_block *sb, sector_t sec) +void exfat_fat_modify(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; @@ -485,12 +316,12 @@ void FAT_modify(struct super_block *sb, sector_t sec) sector_write(sb, sec, bp->buf_bh, 0); } -void FAT_release_all(struct super_block *sb) +void exfat_fat_release_all(struct super_block *sb) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - down(&f_sem); + mutex_lock(&f_mutex); bp = p_fs->FAT_cache_lru_list.next; while (bp != &p_fs->FAT_cache_lru_list) { @@ -507,15 +338,15 @@ void FAT_release_all(struct super_block *sb) bp = bp->next; } - up(&f_sem); + mutex_unlock(&f_mutex); } -void FAT_sync(struct super_block *sb) +void exfat_fat_sync(struct super_block *sb) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - down(&f_sem); + mutex_lock(&f_mutex); bp = p_fs->FAT_cache_lru_list.next; while (bp != &p_fs->FAT_cache_lru_list) { @@ -526,7 +357,7 @@ void FAT_sync(struct super_block *sb) bp = bp->next; } - up(&f_sem); + mutex_unlock(&f_mutex); } static struct buf_cache_t *buf_cache_find(struct super_block *sb, sector_t sec) @@ -561,7 +392,7 @@ static struct buf_cache_t *buf_cache_get(struct super_block *sb, sector_t sec) return bp; } -static u8 *__buf_getblk(struct super_block *sb, sector_t sec) +static u8 *__exfat_buf_getblk(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); @@ -582,7 +413,7 @@ static u8 *__buf_getblk(struct super_block *sb, sector_t sec) buf_cache_insert_hash(sb, bp); - if (sector_read(sb, sec, &bp->buf_bh, 1) != FFS_SUCCESS) { + if (sector_read(sb, sec, &bp->buf_bh, 1) != 0) { buf_cache_remove_hash(bp); bp->drv = -1; bp->sec = ~0; @@ -596,22 +427,22 @@ static u8 *__buf_getblk(struct super_block *sb, sector_t sec) return bp->buf_bh->b_data; } -u8 *buf_getblk(struct super_block *sb, sector_t sec) +u8 *exfat_buf_getblk(struct super_block *sb, sector_t sec) { u8 *buf; - down(&b_sem); - buf = __buf_getblk(sb, sec); - up(&b_sem); + mutex_lock(&b_mutex); + buf = __exfat_buf_getblk(sb, sec); + mutex_unlock(&b_mutex); return buf; } -void buf_modify(struct super_block *sb, sector_t sec) +void exfat_buf_modify(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; - down(&b_sem); + mutex_lock(&b_mutex); bp = buf_cache_find(sb, sec); if (likely(bp)) @@ -620,14 +451,14 @@ void buf_modify(struct super_block *sb, sector_t sec) WARN(!bp, "[EXFAT] failed to find buffer_cache(sector:%llu).\n", (unsigned long long)sec); - up(&b_sem); + mutex_unlock(&b_mutex); } -void buf_lock(struct super_block *sb, sector_t sec) +void exfat_buf_lock(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; - down(&b_sem); + mutex_lock(&b_mutex); bp = buf_cache_find(sb, sec); if (likely(bp)) @@ -636,14 +467,14 @@ void buf_lock(struct super_block *sb, sector_t sec) WARN(!bp, "[EXFAT] failed to find buffer_cache(sector:%llu).\n", (unsigned long long)sec); - up(&b_sem); + mutex_unlock(&b_mutex); } -void buf_unlock(struct super_block *sb, sector_t sec) +void exfat_buf_unlock(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; - down(&b_sem); + mutex_lock(&b_mutex); bp = buf_cache_find(sb, sec); if (likely(bp)) @@ -652,15 +483,15 @@ void buf_unlock(struct super_block *sb, sector_t sec) WARN(!bp, "[EXFAT] failed to find buffer_cache(sector:%llu).\n", (unsigned long long)sec); - up(&b_sem); + mutex_unlock(&b_mutex); } -void buf_release(struct super_block *sb, sector_t sec) +void exfat_buf_release(struct super_block *sb, sector_t sec) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - down(&b_sem); + mutex_lock(&b_mutex); bp = buf_cache_find(sb, sec); if (likely(bp)) { @@ -676,15 +507,15 @@ void buf_release(struct super_block *sb, sector_t sec) move_to_lru(bp, &p_fs->buf_cache_lru_list); } - up(&b_sem); + mutex_unlock(&b_mutex); } -void buf_release_all(struct super_block *sb) +void exfat_buf_release_all(struct super_block *sb) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - down(&b_sem); + mutex_lock(&b_mutex); bp = p_fs->buf_cache_lru_list.next; while (bp != &p_fs->buf_cache_lru_list) { @@ -701,15 +532,15 @@ void buf_release_all(struct super_block *sb) bp = bp->next; } - up(&b_sem); + mutex_unlock(&b_mutex); } -void buf_sync(struct super_block *sb) +void exfat_buf_sync(struct super_block *sb) { struct buf_cache_t *bp; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - down(&b_sem); + mutex_lock(&b_mutex); bp = p_fs->buf_cache_lru_list.next; while (bp != &p_fs->buf_cache_lru_list) { @@ -720,5 +551,5 @@ void buf_sync(struct super_block *sb) bp = bp->next; } - up(&b_sem); + mutex_unlock(&b_mutex); } diff --git a/drivers/staging/exfat/exfat_core.c b/drivers/staging/exfat/exfat_core.c index f3774a1..07b460d 100644 --- a/drivers/staging/exfat/exfat_core.c +++ b/drivers/staging/exfat/exfat_core.c @@ -20,15 +20,6 @@ static void __set_sb_dirty(struct super_block *sb) static u8 name_buf[MAX_PATH_LENGTH * MAX_CHARSET_SIZE]; -static char *reserved_names[] = { - "AUX ", "CON ", "NUL ", "PRN ", - "COM1 ", "COM2 ", "COM3 ", "COM4 ", - "COM5 ", "COM6 ", "COM7 ", "COM8 ", "COM9 ", - "LPT1 ", "LPT2 ", "LPT3 ", "LPT4 ", - "LPT5 ", "LPT6 ", "LPT7 ", "LPT8 ", "LPT9 ", - NULL -}; - static u8 free_bit[] = { 0, 1, 0, 2, 0, 1, 0, 3, 0, 1, 0, 2, 0, 1, 0, 4, 0, 1, 0, 2, /* 0 ~ 19 */ 0, 1, 0, 3, 0, 1, 0, 2, 0, 1, 0, 5, 0, 1, 0, 2, 0, 1, 0, 3, /* 20 ~ 39 */ @@ -99,25 +90,23 @@ void fs_set_vol_flags(struct super_block *sb, u32 new_flag) p_fs->vol_flag = new_flag; - if (p_fs->vol_type == EXFAT) { - if (!p_fs->pbr_bh) { - if (sector_read(sb, p_fs->PBR_sector, - &p_fs->pbr_bh, 1) != FFS_SUCCESS) - return; - } + if (!p_fs->pbr_bh) { + if (sector_read(sb, p_fs->PBR_sector, + &p_fs->pbr_bh, 1) != 0) + return; + } - p_pbr = (struct pbr_sector_t *)p_fs->pbr_bh->b_data; - p_bpb = (struct bpbex_t *)p_pbr->bpb; - SET16(p_bpb->vol_flags, (u16)new_flag); + p_pbr = (struct pbr_sector_t *)p_fs->pbr_bh->b_data; + p_bpb = (struct bpbex_t *)p_pbr->bpb; + SET16(p_bpb->vol_flags, (u16)new_flag); - /* XXX duyoung - * what can we do here? (cuz fs_set_vol_flags() is void) - */ - if ((new_flag == VOL_DIRTY) && (!buffer_dirty(p_fs->pbr_bh))) - sector_write(sb, p_fs->PBR_sector, p_fs->pbr_bh, 1); - else - sector_write(sb, p_fs->PBR_sector, p_fs->pbr_bh, 0); - } + /* XXX duyoung + * what can we do here? (cuz fs_set_vol_flags() is void) + */ + if ((new_flag == VOL_DIRTY) && (!buffer_dirty(p_fs->pbr_bh))) + sector_write(sb, p_fs->PBR_sector, p_fs->pbr_bh, 1); + else + sector_write(sb, p_fs->PBR_sector, p_fs->pbr_bh, 0); } void fs_error(struct super_block *sb) @@ -136,10 +125,10 @@ void fs_error(struct super_block *sb) * Cluster Management Functions */ -s32 clear_cluster(struct super_block *sb, u32 clu) +static s32 clear_cluster(struct super_block *sb, u32 clu) { sector_t s, n; - s32 ret = FFS_SUCCESS; + s32 ret = 0; struct buffer_head *tmp_bh = NULL; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); @@ -154,12 +143,12 @@ s32 clear_cluster(struct super_block *sb, u32 clu) for (; s < n; s++) { ret = sector_read(sb, s, &tmp_bh, 0); - if (ret != FFS_SUCCESS) + if (ret != 0) return ret; memset((char *)tmp_bh->b_data, 0x0, p_bd->sector_size); ret = sector_write(sb, s, tmp_bh, 0); - if (ret != FFS_SUCCESS) + if (ret != 0) break; } @@ -167,58 +156,97 @@ s32 clear_cluster(struct super_block *sb, u32 clu) return ret; } -s32 fat_alloc_cluster(struct super_block *sb, s32 num_alloc, - struct chain_t *p_chain) +static s32 set_alloc_bitmap(struct super_block *sb, u32 clu) { - int i, num_clusters = 0; - u32 new_clu, last_clu = CLUSTER_32(~0), read_clu; + int i, b; + sector_t sector; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); + struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - new_clu = p_chain->dir; - if (new_clu == CLUSTER_32(~0)) - new_clu = p_fs->clu_srch_ptr; - else if (new_clu >= p_fs->num_clusters) - new_clu = 2; + i = clu >> (p_bd->sector_size_bits + 3); + b = clu & ((p_bd->sector_size << 3) - 1); - __set_sb_dirty(sb); + sector = START_SECTOR(p_fs->map_clu) + i; - p_chain->dir = CLUSTER_32(~0); + exfat_bitmap_set((u8 *)p_fs->vol_amap[i]->b_data, b); - for (i = 2; i < p_fs->num_clusters; i++) { - if (FAT_read(sb, new_clu, &read_clu) != 0) - return -1; + return sector_write(sb, sector, p_fs->vol_amap[i], 0); +} - if (read_clu == CLUSTER_32(0)) { - if (FAT_write(sb, new_clu, CLUSTER_32(~0)) < 0) - return -1; - num_clusters++; +static s32 clr_alloc_bitmap(struct super_block *sb, u32 clu) +{ + int i, b; + sector_t sector; +#ifdef CONFIG_STAGING_EXFAT_DISCARD + struct exfat_sb_info *sbi = EXFAT_SB(sb); + struct exfat_mount_options *opts = &sbi->options; + int ret; +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ + struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); + struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - if (p_chain->dir == CLUSTER_32(~0)) { - p_chain->dir = new_clu; - } else { - if (FAT_write(sb, last_clu, new_clu) < 0) - return -1; - } + i = clu >> (p_bd->sector_size_bits + 3); + b = clu & ((p_bd->sector_size << 3) - 1); - last_clu = new_clu; + sector = START_SECTOR(p_fs->map_clu) + i; - if ((--num_alloc) == 0) { - p_fs->clu_srch_ptr = new_clu; - if (p_fs->used_clusters != UINT_MAX) - p_fs->used_clusters += num_clusters; + exfat_bitmap_clear((u8 *)p_fs->vol_amap[i]->b_data, b); - return num_clusters; - } +#ifdef CONFIG_STAGING_EXFAT_DISCARD + if (opts->discard) { + ret = sb_issue_discard(sb, START_SECTOR(clu), + (1 << p_fs->sectors_per_clu_bits), + GFP_NOFS, 0); + if (ret == -EOPNOTSUPP) { + pr_warn("discard not supported by device, disabling"); + opts->discard = 0; + } else { + return ret; } - if ((++new_clu) >= p_fs->num_clusters) - new_clu = 2; } +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ - p_fs->clu_srch_ptr = new_clu; - if (p_fs->used_clusters != UINT_MAX) - p_fs->used_clusters += num_clusters; + return sector_write(sb, sector, p_fs->vol_amap[i], 0); +} - return num_clusters; +static u32 test_alloc_bitmap(struct super_block *sb, u32 clu) +{ + int i, map_i, map_b; + u32 clu_base, clu_free; + u8 k, clu_mask; + struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); + struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); + + clu_base = (clu & ~(0x7)) + 2; + clu_mask = (1 << (clu - clu_base + 2)) - 1; + + map_i = clu >> (p_bd->sector_size_bits + 3); + map_b = (clu >> 3) & p_bd->sector_size_mask; + + for (i = 2; i < p_fs->num_clusters; i += 8) { + k = *(((u8 *)p_fs->vol_amap[map_i]->b_data) + map_b); + if (clu_mask > 0) { + k |= clu_mask; + clu_mask = 0; + } + if (k < 0xFF) { + clu_free = clu_base + free_bit[k]; + if (clu_free < p_fs->num_clusters) + return clu_free; + } + clu_base += 8; + + if (((++map_b) >= p_bd->sector_size) || + (clu_base >= p_fs->num_clusters)) { + if ((++map_i) >= p_fs->map_sectors) { + clu_base = 2; + map_i = 0; + } + map_b = 0; + } + } + + return CLUSTER_32(~0); } s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, @@ -251,22 +279,22 @@ s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, } } - if (set_alloc_bitmap(sb, new_clu - 2) != FFS_SUCCESS) - return -1; + if (set_alloc_bitmap(sb, new_clu - 2) != 0) + return -EIO; num_clusters++; if (p_chain->flags == 0x01) { - if (FAT_write(sb, new_clu, CLUSTER_32(~0)) < 0) - return -1; + if (exfat_fat_write(sb, new_clu, CLUSTER_32(~0)) < 0) + return -EIO; } if (p_chain->dir == CLUSTER_32(~0)) { p_chain->dir = new_clu; } else { if (p_chain->flags == 0x01) { - if (FAT_write(sb, last_clu, new_clu) < 0) - return -1; + if (exfat_fat_write(sb, last_clu, new_clu) < 0) + return -EIO; } } last_clu = new_clu; @@ -300,47 +328,6 @@ s32 exfat_alloc_cluster(struct super_block *sb, s32 num_alloc, return num_clusters; } -void fat_free_cluster(struct super_block *sb, struct chain_t *p_chain, - s32 do_relse) -{ - s32 num_clusters = 0; - u32 clu, prev; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - int i; - sector_t sector; - - if ((p_chain->dir == CLUSTER_32(0)) || (p_chain->dir == CLUSTER_32(~0))) - return; - __set_sb_dirty(sb); - clu = p_chain->dir; - - if (p_chain->size <= 0) - return; - - do { - if (p_fs->dev_ejected) - break; - - if (do_relse) { - sector = START_SECTOR(clu); - for (i = 0; i < p_fs->sectors_per_clu; i++) - buf_release(sb, sector + i); - } - - prev = clu; - if (FAT_read(sb, clu, &clu) == -1) - break; - - if (FAT_write(sb, prev, CLUSTER_32(0)) < 0) - break; - num_clusters++; - - } while (clu != CLUSTER_32(~0)); - - if (p_fs->used_clusters != UINT_MAX) - p_fs->used_clusters -= num_clusters; -} - void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, s32 do_relse) { @@ -367,10 +354,10 @@ void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, if (do_relse) { sector = START_SECTOR(clu); for (i = 0; i < p_fs->sectors_per_clu; i++) - buf_release(sb, sector + i); + exfat_buf_release(sb, sector + i); } - if (clr_alloc_bitmap(sb, clu - 2) != FFS_SUCCESS) + if (clr_alloc_bitmap(sb, clu - 2) != 0) break; clu++; @@ -384,13 +371,13 @@ void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, if (do_relse) { sector = START_SECTOR(clu); for (i = 0; i < p_fs->sectors_per_clu; i++) - buf_release(sb, sector + i); + exfat_buf_release(sb, sector + i); } - if (clr_alloc_bitmap(sb, clu - 2) != FFS_SUCCESS) + if (clr_alloc_bitmap(sb, clu - 2) != 0) break; - if (FAT_read(sb, clu, &clu) == -1) + if (exfat_fat_read(sb, clu, &clu) == -1) break; num_clusters++; } while ((clu != CLUSTER_32(0)) && (clu != CLUSTER_32(~0))); @@ -400,7 +387,7 @@ void exfat_free_cluster(struct super_block *sb, struct chain_t *p_chain, p_fs->used_clusters -= num_clusters; } -u32 find_last_cluster(struct super_block *sb, struct chain_t *p_chain) +static u32 find_last_cluster(struct super_block *sb, struct chain_t *p_chain) { u32 clu, next; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); @@ -410,7 +397,7 @@ u32 find_last_cluster(struct super_block *sb, struct chain_t *p_chain) if (p_chain->flags == 0x03) { clu += p_chain->size - 1; } else { - while ((FAT_read(sb, clu, &next) == 0) && + while ((exfat_fat_read(sb, clu, &next) == 0) && (next != CLUSTER_32(~0))) { if (p_fs->dev_ejected) break; @@ -437,7 +424,7 @@ s32 count_num_clusters(struct super_block *sb, struct chain_t *p_chain) } else { for (i = 2; i < p_fs->num_clusters; i++) { count++; - if (FAT_read(sb, clu, &clu) != 0) + if (exfat_fat_read(sb, clu, &clu) != 0) return 0; if (clu == CLUSTER_32(~0)) break; @@ -447,22 +434,6 @@ s32 count_num_clusters(struct super_block *sb, struct chain_t *p_chain) return count; } -s32 fat_count_used_clusters(struct super_block *sb) -{ - int i, count = 0; - u32 clu; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - for (i = 2; i < p_fs->num_clusters; i++) { - if (FAT_read(sb, i, &clu) != 0) - break; - if (clu != CLUSTER_32(0)) - count++; - } - - return count; -} - s32 exfat_count_used_clusters(struct super_block *sb) { int i, map_i, map_b, count = 0; @@ -470,7 +441,8 @@ s32 exfat_count_used_clusters(struct super_block *sb) struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - map_i = map_b = 0; + map_i = 0; + map_b = 0; for (i = 2; i < p_fs->num_clusters; i += 8) { k = *(((u8 *)p_fs->vol_amap[map_i]->b_data) + map_b); @@ -491,12 +463,12 @@ void exfat_chain_cont_cluster(struct super_block *sb, u32 chain, s32 len) return; while (len > 1) { - if (FAT_write(sb, chain, chain + 1) < 0) + if (exfat_fat_write(sb, chain, chain + 1) < 0) break; chain++; len--; } - FAT_write(sb, chain, CLUSTER_32(~0)); + exfat_fat_write(sb, chain, CLUSTER_32(~0)); } /* @@ -525,9 +497,9 @@ s32 load_alloc_bitmap(struct super_block *sb) ep = (struct bmap_dentry_t *)get_entry_in_dir(sb, &clu, i, NULL); if (!ep) - return FFS_MEDIAERR; + return -ENOENT; - type = p_fs->fs_func->get_entry_type((struct dentry_t *)ep); + type = exfat_get_entry_type((struct dentry_t *)ep); if (type == TYPE_UNUSED) break; @@ -544,14 +516,14 @@ s32 load_alloc_bitmap(struct super_block *sb) sizeof(struct buffer_head *), GFP_KERNEL); if (!p_fs->vol_amap) - return FFS_MEMORYERR; + return -ENOMEM; sector = START_SECTOR(p_fs->map_clu); for (j = 0; j < p_fs->map_sectors; j++) { p_fs->vol_amap[j] = NULL; - ret = sector_read(sb, sector + j, &(p_fs->vol_amap[j]), 1); - if (ret != FFS_SUCCESS) { + ret = sector_read(sb, sector + j, &p_fs->vol_amap[j], 1); + if (ret != 0) { /* release all buffers and free vol_amap */ i = 0; while (i < j) @@ -564,15 +536,15 @@ s32 load_alloc_bitmap(struct super_block *sb) } p_fs->pbr_bh = NULL; - return FFS_SUCCESS; + return 0; } } - if (FAT_read(sb, clu.dir, &clu.dir) != 0) - return FFS_MEDIAERR; + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) + return -EIO; } - return FFS_FORMATERR; + return -EFSCORRUPTED; } void free_alloc_bitmap(struct super_block *sb) @@ -589,97 +561,6 @@ void free_alloc_bitmap(struct super_block *sb) p_fs->vol_amap = NULL; } -s32 set_alloc_bitmap(struct super_block *sb, u32 clu) -{ - int i, b; - sector_t sector; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - - i = clu >> (p_bd->sector_size_bits + 3); - b = clu & ((p_bd->sector_size << 3) - 1); - - sector = START_SECTOR(p_fs->map_clu) + i; - - exfat_bitmap_set((u8 *)p_fs->vol_amap[i]->b_data, b); - - return sector_write(sb, sector, p_fs->vol_amap[i], 0); -} - -s32 clr_alloc_bitmap(struct super_block *sb, u32 clu) -{ - int i, b; - sector_t sector; -#ifdef CONFIG_EXFAT_DISCARD - struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct exfat_mount_options *opts = &sbi->options; - int ret; -#endif /* CONFIG_EXFAT_DISCARD */ - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - - i = clu >> (p_bd->sector_size_bits + 3); - b = clu & ((p_bd->sector_size << 3) - 1); - - sector = START_SECTOR(p_fs->map_clu) + i; - - exfat_bitmap_clear((u8 *)p_fs->vol_amap[i]->b_data, b); - - return sector_write(sb, sector, p_fs->vol_amap[i], 0); - -#ifdef CONFIG_EXFAT_DISCARD - if (opts->discard) { - ret = sb_issue_discard(sb, START_SECTOR(clu), - (1 << p_fs->sectors_per_clu_bits), - GFP_NOFS, 0); - if (ret == -EOPNOTSUPP) { - pr_warn("discard not supported by device, disabling"); - opts->discard = 0; - } - } -#endif /* CONFIG_EXFAT_DISCARD */ -} - -u32 test_alloc_bitmap(struct super_block *sb, u32 clu) -{ - int i, map_i, map_b; - u32 clu_base, clu_free; - u8 k, clu_mask; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - - clu_base = (clu & ~(0x7)) + 2; - clu_mask = (1 << (clu - clu_base + 2)) - 1; - - map_i = clu >> (p_bd->sector_size_bits + 3); - map_b = (clu >> 3) & p_bd->sector_size_mask; - - for (i = 2; i < p_fs->num_clusters; i += 8) { - k = *(((u8 *)p_fs->vol_amap[map_i]->b_data) + map_b); - if (clu_mask > 0) { - k |= clu_mask; - clu_mask = 0; - } - if (k < 0xFF) { - clu_free = clu_base + free_bit[k]; - if (clu_free < p_fs->num_clusters) - return clu_free; - } - clu_base += 8; - - if (((++map_b) >= p_bd->sector_size) || - (clu_base >= p_fs->num_clusters)) { - if ((++map_i) >= p_fs->map_sectors) { - clu_base = 2; - map_i = 0; - } - map_b = 0; - } - } - - return CLUSTER_32(~0); -} - void sync_alloc_bitmap(struct super_block *sb) { int i; @@ -698,7 +579,7 @@ void sync_alloc_bitmap(struct super_block *sb) static s32 __load_upcase_table(struct super_block *sb, sector_t sector, u32 num_sectors, u32 utbl_checksum) { - int i, ret = FFS_ERROR; + int i, ret = -EINVAL; u32 j; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); @@ -712,15 +593,15 @@ static s32 __load_upcase_table(struct super_block *sb, sector_t sector, u32 checksum = 0; - upcase_table = p_fs->vol_utbl = kmalloc(UTBL_COL_COUNT * sizeof(u16 *), - GFP_KERNEL); + upcase_table = kmalloc_array(UTBL_COL_COUNT, sizeof(u16 *), GFP_KERNEL); + p_fs->vol_utbl = upcase_table; if (!upcase_table) - return FFS_MEMORYERR; + return -ENOMEM; memset(upcase_table, 0, UTBL_COL_COUNT * sizeof(u16 *)); while (sector < end_sector) { ret = sector_read(sb, sector, &tmp_bh, 1); - if (ret != FFS_SUCCESS) { + if (ret != 0) { pr_debug("sector read (0x%llX)fail\n", (unsigned long long)sector); goto error; @@ -755,7 +636,7 @@ static s32 __load_upcase_table(struct super_block *sb, sector_t sector, upcase_table[col_index] = kmalloc_array(UTBL_ROW_COUNT, sizeof(u16), GFP_KERNEL); if (!upcase_table[col_index]) { - ret = FFS_MEMORYERR; + ret = -ENOMEM; goto error; } @@ -771,9 +652,9 @@ static s32 __load_upcase_table(struct super_block *sb, sector_t sector, if (index >= 0xFFFF && utbl_checksum == checksum) { if (tmp_bh) brelse(tmp_bh); - return FFS_SUCCESS; + return 0; } - ret = FFS_ERROR; + ret = -EINVAL; error: if (tmp_bh) brelse(tmp_bh); @@ -783,7 +664,7 @@ error: static s32 __load_default_upcase_table(struct super_block *sb) { - int i, ret = FFS_ERROR; + int i, ret = -EINVAL; u32 j; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); @@ -792,10 +673,10 @@ static s32 __load_default_upcase_table(struct super_block *sb) u16 uni = 0; u16 **upcase_table; - upcase_table = p_fs->vol_utbl = kmalloc(UTBL_COL_COUNT * sizeof(u16 *), - GFP_KERNEL); + upcase_table = kmalloc_array(UTBL_COL_COUNT, sizeof(u16 *), GFP_KERNEL); + p_fs->vol_utbl = upcase_table; if (!upcase_table) - return FFS_MEMORYERR; + return -ENOMEM; memset(upcase_table, 0, UTBL_COL_COUNT * sizeof(u16 *)); for (i = 0; index <= 0xFFFF && i < NUM_UPCASE * 2; i += 2) { @@ -818,7 +699,7 @@ static s32 __load_default_upcase_table(struct super_block *sb) sizeof(u16), GFP_KERNEL); if (!upcase_table[col_index]) { - ret = FFS_MEMORYERR; + ret = -ENOMEM; goto error; } @@ -832,7 +713,7 @@ static s32 __load_default_upcase_table(struct super_block *sb) } if (index >= 0xFFFF) - return FFS_SUCCESS; + return 0; error: /* FATAL error: default upcase table has error */ @@ -855,16 +736,16 @@ s32 load_upcase_table(struct super_block *sb) clu.flags = 0x01; if (p_fs->dev_ejected) - return FFS_MEDIAERR; + return -EIO; while (clu.dir != CLUSTER_32(~0)) { for (i = 0; i < p_fs->dentries_per_clu; i++) { ep = (struct case_dentry_t *)get_entry_in_dir(sb, &clu, i, NULL); if (!ep) - return FFS_MEDIAERR; + return -ENOENT; - type = p_fs->fs_func->get_entry_type((struct dentry_t *)ep); + type = exfat_get_entry_type((struct dentry_t *)ep); if (type == TYPE_UNUSED) break; @@ -877,12 +758,12 @@ s32 load_upcase_table(struct super_block *sb) sector = START_SECTOR(tbl_clu); num_sectors = ((tbl_size - 1) >> p_bd->sector_size_bits) + 1; if (__load_upcase_table(sb, sector, num_sectors, - GET32_A(ep->checksum)) != FFS_SUCCESS) + GET32_A(ep->checksum)) != 0) break; - return FFS_SUCCESS; + return 0; } - if (FAT_read(sb, clu.dir, &clu.dir) != 0) - return FFS_MEDIAERR; + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) + return -EIO; } /* load default upcase table */ return __load_default_upcase_table(sb); @@ -906,28 +787,6 @@ void free_upcase_table(struct super_block *sb) * Directory Entry Management Functions */ -u32 fat_get_entry_type(struct dentry_t *p_entry) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - if (*(ep->name) == 0x0) - return TYPE_UNUSED; - - else if (*(ep->name) == 0xE5) - return TYPE_DELETED; - - else if (ep->attr == ATTR_EXTEND) - return TYPE_EXTEND; - - else if ((ep->attr & (ATTR_SUBDIR | ATTR_VOLUME)) == ATTR_VOLUME) - return TYPE_VOLUME; - - else if ((ep->attr & (ATTR_SUBDIR | ATTR_VOLUME)) == ATTR_SUBDIR) - return TYPE_DIR; - - return TYPE_FILE; -} - u32 exfat_get_entry_type(struct dentry_t *p_entry) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; @@ -973,30 +832,7 @@ u32 exfat_get_entry_type(struct dentry_t *p_entry) return TYPE_BENIGN_SEC; } -void fat_set_entry_type(struct dentry_t *p_entry, u32 type) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - if (type == TYPE_UNUSED) - *(ep->name) = 0x0; - - else if (type == TYPE_DELETED) - *(ep->name) = 0xE5; - - else if (type == TYPE_EXTEND) - ep->attr = ATTR_EXTEND; - - else if (type == TYPE_DIR) - ep->attr = ATTR_SUBDIR; - - else if (type == TYPE_FILE) - ep->attr = ATTR_ARCHIVE; - - else if (type == TYPE_SYMLINK) - ep->attr = ATTR_ARCHIVE | ATTR_SYMLINK; -} - -void exfat_set_entry_type(struct dentry_t *p_entry, u32 type) +static void exfat_set_entry_type(struct dentry_t *p_entry, u32 type) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; @@ -1026,13 +862,6 @@ void exfat_set_entry_type(struct dentry_t *p_entry, u32 type) } } -u32 fat_get_entry_attr(struct dentry_t *p_entry) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - return (u32)ep->attr; -} - u32 exfat_get_entry_attr(struct dentry_t *p_entry) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; @@ -1040,13 +869,6 @@ u32 exfat_get_entry_attr(struct dentry_t *p_entry) return (u32)GET16_A(ep->attr); } -void fat_set_entry_attr(struct dentry_t *p_entry, u32 attr) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - ep->attr = (u8)attr; -} - void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr) { struct file_dentry_t *ep = (struct file_dentry_t *)p_entry; @@ -1054,11 +876,6 @@ void exfat_set_entry_attr(struct dentry_t *p_entry, u32 attr) SET16_A(ep->attr, (u16)attr); } -u8 fat_get_entry_flag(struct dentry_t *p_entry) -{ - return 0x01; -} - u8 exfat_get_entry_flag(struct dentry_t *p_entry) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -1066,10 +883,6 @@ u8 exfat_get_entry_flag(struct dentry_t *p_entry) return ep->flags; } -void fat_set_entry_flag(struct dentry_t *p_entry, u8 flags) -{ -} - void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -1077,29 +890,13 @@ void exfat_set_entry_flag(struct dentry_t *p_entry, u8 flags) ep->flags = flags; } -u32 fat_get_entry_clu0(struct dentry_t *p_entry) +u32 exfat_get_entry_clu0(struct dentry_t *p_entry) { - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - return ((u32)GET16_A(ep->start_clu_hi) << 16) | - GET16_A(ep->start_clu_lo); -} - -u32 exfat_get_entry_clu0(struct dentry_t *p_entry) -{ - struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; + struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; return GET32_A(ep->start_clu); } -void fat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - SET16_A(ep->start_clu_lo, CLUSTER_16(start_clu)); - SET16_A(ep->start_clu_hi, CLUSTER_16(start_clu >> 16)); -} - void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -1107,13 +904,6 @@ void exfat_set_entry_clu0(struct dentry_t *p_entry, u32 start_clu) SET32_A(ep->start_clu, start_clu); } -u64 fat_get_entry_size(struct dentry_t *p_entry) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - return (u64)GET32_A(ep->size); -} - u64 exfat_get_entry_size(struct dentry_t *p_entry) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -1121,13 +911,6 @@ u64 exfat_get_entry_size(struct dentry_t *p_entry) return GET64_A(ep->valid_size); } -void fat_set_entry_size(struct dentry_t *p_entry, u64 size) -{ - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - SET32_A(ep->size, (u32)size); -} - void exfat_set_entry_size(struct dentry_t *p_entry, u64 size) { struct strm_dentry_t *ep = (struct strm_dentry_t *)p_entry; @@ -1136,31 +919,6 @@ void exfat_set_entry_size(struct dentry_t *p_entry, u64 size) SET64_A(ep->size, size); } -void fat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode) -{ - u16 t = 0x00, d = 0x21; - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - switch (mode) { - case TM_CREATE: - t = GET16_A(ep->create_time); - d = GET16_A(ep->create_date); - break; - case TM_MODIFY: - t = GET16_A(ep->modify_time); - d = GET16_A(ep->modify_date); - break; - } - - tp->sec = (t & 0x001F) << 1; - tp->min = (t >> 5) & 0x003F; - tp->hour = (t >> 11); - tp->day = (d & 0x001F); - tp->mon = (d >> 5) & 0x000F; - tp->year = (d >> 9); -} - void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, u8 mode) { @@ -1190,27 +948,6 @@ void exfat_get_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, tp->year = (d >> 9); } -void fat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, - u8 mode) -{ - u16 t, d; - struct dos_dentry_t *ep = (struct dos_dentry_t *)p_entry; - - t = (tp->hour << 11) | (tp->min << 5) | (tp->sec >> 1); - d = (tp->year << 9) | (tp->mon << 5) | tp->day; - - switch (mode) { - case TM_CREATE: - SET16_A(ep->create_time, t); - SET16_A(ep->create_date, d); - break; - case TM_MODIFY: - SET16_A(ep->modify_time, t); - SET16_A(ep->modify_date, d); - break; - } -} - void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, u8 mode) { @@ -1236,25 +973,47 @@ void exfat_set_entry_time(struct dentry_t *p_entry, struct timestamp_t *tp, } } -s32 fat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, s32 entry, - u32 type, u32 start_clu, u64 size) +static void init_file_entry(struct file_dentry_t *ep, u32 type) { - sector_t sector; - struct dos_dentry_t *dos_ep; + struct timestamp_t tm, *tp; + + exfat_set_entry_type((struct dentry_t *)ep, type); + + tp = tm_current(&tm); + exfat_set_entry_time((struct dentry_t *)ep, tp, TM_CREATE); + exfat_set_entry_time((struct dentry_t *)ep, tp, TM_MODIFY); + exfat_set_entry_time((struct dentry_t *)ep, tp, TM_ACCESS); + ep->create_time_ms = 0; + ep->modify_time_ms = 0; + ep->access_time_ms = 0; +} + +static void init_strm_entry(struct strm_dentry_t *ep, u8 flags, u32 start_clu, u64 size) +{ + exfat_set_entry_type((struct dentry_t *)ep, TYPE_STREAM); + ep->flags = flags; + SET32_A(ep->start_clu, start_clu); + SET64_A(ep->valid_size, size); + SET64_A(ep->size, size); +} - dos_ep = (struct dos_dentry_t *)get_entry_in_dir(sb, p_dir, entry, - §or); - if (!dos_ep) - return FFS_MEDIAERR; +static void init_name_entry(struct name_dentry_t *ep, u16 *uniname) +{ + int i; - init_dos_entry(dos_ep, type, start_clu); - buf_modify(sb, sector); + exfat_set_entry_type((struct dentry_t *)ep, TYPE_EXTEND); + ep->flags = 0x0; - return FFS_SUCCESS; + for (i = 0; i < 30; i++, i++) { + SET16_A(ep->unicode_0_14 + i, *uniname); + if (*uniname == 0x0) + break; + uniname++; + } } -s32 exfat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, u32 type, u32 start_clu, u64 size) +static s32 exfat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, + s32 entry, u32 type, u32 start_clu, u64 size) { sector_t sector; u8 flags; @@ -1267,71 +1026,20 @@ s32 exfat_init_dir_entry(struct super_block *sb, struct chain_t *p_dir, file_ep = (struct file_dentry_t *)get_entry_in_dir(sb, p_dir, entry, §or); if (!file_ep) - return FFS_MEDIAERR; + return -ENOENT; strm_ep = (struct strm_dentry_t *)get_entry_in_dir(sb, p_dir, entry + 1, §or); if (!strm_ep) - return FFS_MEDIAERR; + return -ENOENT; init_file_entry(file_ep, type); - buf_modify(sb, sector); + exfat_buf_modify(sb, sector); init_strm_entry(strm_ep, flags, start_clu, size); - buf_modify(sb, sector); - - return FFS_SUCCESS; -} - -static s32 fat_init_ext_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 num_entries, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname) -{ - int i; - sector_t sector; - u8 chksum; - u16 *uniname = p_uniname->name; - struct dos_dentry_t *dos_ep; - struct ext_dentry_t *ext_ep; - - dos_ep = (struct dos_dentry_t *)get_entry_in_dir(sb, p_dir, entry, - §or); - if (!dos_ep) - return FFS_MEDIAERR; - - dos_ep->lcase = p_dosname->name_case; - memcpy(dos_ep->name, p_dosname->name, DOS_NAME_LENGTH); - buf_modify(sb, sector); - - if ((--num_entries) > 0) { - chksum = calc_checksum_1byte((void *)dos_ep->name, - DOS_NAME_LENGTH, 0); - - for (i = 1; i < num_entries; i++) { - ext_ep = (struct ext_dentry_t *)get_entry_in_dir(sb, - p_dir, - entry - i, - §or); - if (!ext_ep) - return FFS_MEDIAERR; - - init_ext_entry(ext_ep, i, chksum, uniname); - buf_modify(sb, sector); - uniname += 13; - } - - ext_ep = (struct ext_dentry_t *)get_entry_in_dir(sb, p_dir, - entry - i, - §or); - if (!ext_ep) - return FFS_MEDIAERR; - - init_ext_entry(ext_ep, i + 0x40, chksum, uniname); - buf_modify(sb, sector); - } + exfat_buf_modify(sb, sector); - return FFS_SUCCESS; + return 0; } static s32 exfat_init_ext_entry(struct super_block *sb, struct chain_t *p_dir, @@ -1349,173 +1057,51 @@ static s32 exfat_init_ext_entry(struct super_block *sb, struct chain_t *p_dir, file_ep = (struct file_dentry_t *)get_entry_in_dir(sb, p_dir, entry, §or); if (!file_ep) - return FFS_MEDIAERR; + return -ENOENT; file_ep->num_ext = (u8)(num_entries - 1); - buf_modify(sb, sector); + exfat_buf_modify(sb, sector); strm_ep = (struct strm_dentry_t *)get_entry_in_dir(sb, p_dir, entry + 1, §or); if (!strm_ep) - return FFS_MEDIAERR; + return -ENOENT; strm_ep->name_len = p_uniname->name_len; SET16_A(strm_ep->name_hash, p_uniname->name_hash); - buf_modify(sb, sector); + exfat_buf_modify(sb, sector); for (i = 2; i < num_entries; i++) { name_ep = (struct name_dentry_t *)get_entry_in_dir(sb, p_dir, entry + i, §or); if (!name_ep) - return FFS_MEDIAERR; + return -ENOENT; init_name_entry(name_ep, uniname); - buf_modify(sb, sector); + exfat_buf_modify(sb, sector); uniname += 15; } update_dir_checksum(sb, p_dir, entry); - return FFS_SUCCESS; -} - -void init_dos_entry(struct dos_dentry_t *ep, u32 type, u32 start_clu) -{ - struct timestamp_t tm, *tp; - - fat_set_entry_type((struct dentry_t *)ep, type); - SET16_A(ep->start_clu_lo, CLUSTER_16(start_clu)); - SET16_A(ep->start_clu_hi, CLUSTER_16(start_clu >> 16)); - SET32_A(ep->size, 0); - - tp = tm_current(&tm); - fat_set_entry_time((struct dentry_t *)ep, tp, TM_CREATE); - fat_set_entry_time((struct dentry_t *)ep, tp, TM_MODIFY); - SET16_A(ep->access_date, 0); - ep->create_time_ms = 0; -} - -void init_ext_entry(struct ext_dentry_t *ep, s32 order, u8 chksum, u16 *uniname) -{ - int i; - bool end = false; - - fat_set_entry_type((struct dentry_t *)ep, TYPE_EXTEND); - ep->order = (u8)order; - ep->sysid = 0; - ep->checksum = chksum; - SET16_A(ep->start_clu, 0); - - for (i = 0; i < 10; i += 2) { - if (!end) { - SET16(ep->unicode_0_4 + i, *uniname); - if (*uniname == 0x0) - end = true; - else - uniname++; - } else { - SET16(ep->unicode_0_4 + i, 0xFFFF); - } - } - - for (i = 0; i < 12; i += 2) { - if (!end) { - SET16_A(ep->unicode_5_10 + i, *uniname); - if (*uniname == 0x0) - end = true; - else - uniname++; - } else { - SET16_A(ep->unicode_5_10 + i, 0xFFFF); - } - } - - for (i = 0; i < 4; i += 2) { - if (!end) { - SET16_A(ep->unicode_11_12 + i, *uniname); - if (*uniname == 0x0) - end = true; - else - uniname++; - } else { - SET16_A(ep->unicode_11_12 + i, 0xFFFF); - } - } -} - -void init_file_entry(struct file_dentry_t *ep, u32 type) -{ - struct timestamp_t tm, *tp; - - exfat_set_entry_type((struct dentry_t *)ep, type); - - tp = tm_current(&tm); - exfat_set_entry_time((struct dentry_t *)ep, tp, TM_CREATE); - exfat_set_entry_time((struct dentry_t *)ep, tp, TM_MODIFY); - exfat_set_entry_time((struct dentry_t *)ep, tp, TM_ACCESS); - ep->create_time_ms = 0; - ep->modify_time_ms = 0; - ep->access_time_ms = 0; -} - -void init_strm_entry(struct strm_dentry_t *ep, u8 flags, u32 start_clu, u64 size) -{ - exfat_set_entry_type((struct dentry_t *)ep, TYPE_STREAM); - ep->flags = flags; - SET32_A(ep->start_clu, start_clu); - SET64_A(ep->valid_size, size); - SET64_A(ep->size, size); -} - -void init_name_entry(struct name_dentry_t *ep, u16 *uniname) -{ - int i; - - exfat_set_entry_type((struct dentry_t *)ep, TYPE_EXTEND); - ep->flags = 0x0; - - for (i = 0; i < 30; i++, i++) { - SET16_A(ep->unicode_0_14 + i, *uniname); - if (*uniname == 0x0) - break; - uniname++; - } -} - -void fat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 order, s32 num_entries) -{ - int i; - sector_t sector; - struct dentry_t *ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - for (i = num_entries - 1; i >= order; i--) { - ep = get_entry_in_dir(sb, p_dir, entry - i, §or); - if (!ep) - return; - - p_fs->fs_func->set_entry_type(ep, TYPE_DELETED); - buf_modify(sb, sector); - } + return 0; } void exfat_delete_dir_entry(struct super_block *sb, struct chain_t *p_dir, - s32 entry, s32 order, s32 num_entries) + s32 entry, s32 order, s32 num_entries) { int i; sector_t sector; struct dentry_t *ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); for (i = order; i < num_entries; i++) { ep = get_entry_in_dir(sb, p_dir, entry + i, §or); if (!ep) return; - p_fs->fs_func->set_entry_type(ep, TYPE_DELETED); - buf_modify(sb, sector); + exfat_set_entry_type(ep, TYPE_DELETED); + exfat_buf_modify(sb, sector); } } @@ -1533,7 +1119,7 @@ void update_dir_checksum(struct super_block *sb, struct chain_t *p_dir, if (!file_ep) return; - buf_lock(sb, sector); + exfat_buf_lock(sb, sector); num_entries = (s32)file_ep->num_ext + 1; chksum = calc_checksum_2byte((void *)file_ep, DENTRY_SIZE, 0, @@ -1542,7 +1128,7 @@ void update_dir_checksum(struct super_block *sb, struct chain_t *p_dir, for (i = 1; i < num_entries; i++) { ep = get_entry_in_dir(sb, p_dir, entry + i, NULL); if (!ep) { - buf_unlock(sb, sector); + exfat_buf_unlock(sb, sector); return; } @@ -1551,8 +1137,75 @@ void update_dir_checksum(struct super_block *sb, struct chain_t *p_dir, } SET16_A(file_ep->checksum, chksum); - buf_modify(sb, sector); - buf_unlock(sb, sector); + exfat_buf_modify(sb, sector); + exfat_buf_unlock(sb, sector); +} + +static s32 __write_partial_entries_in_entry_set(struct super_block *sb, + struct entry_set_cache_t *es, + sector_t sec, s32 off, u32 count) +{ + s32 num_entries, buf_off = (off - es->offset); + u32 remaining_byte_in_sector, copy_entries; + struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); + struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); + u32 clu; + u8 *buf, *esbuf = (u8 *)&es->__buf; + + pr_debug("%s entered es %p sec %llu off %d count %d\n", + __func__, es, (unsigned long long)sec, off, count); + num_entries = count; + + while (num_entries) { + /* white per sector base */ + remaining_byte_in_sector = (1 << p_bd->sector_size_bits) - off; + copy_entries = min_t(s32, + remaining_byte_in_sector >> DENTRY_SIZE_BITS, + num_entries); + buf = exfat_buf_getblk(sb, sec); + if (!buf) + goto err_out; + pr_debug("es->buf %p buf_off %u\n", esbuf, buf_off); + pr_debug("copying %d entries from %p to sector %llu\n", + copy_entries, (esbuf + buf_off), + (unsigned long long)sec); + memcpy(buf + off, esbuf + buf_off, + copy_entries << DENTRY_SIZE_BITS); + exfat_buf_modify(sb, sec); + num_entries -= copy_entries; + + if (num_entries) { + /* get next sector */ + if (IS_LAST_SECTOR_IN_CLUSTER(sec)) { + clu = GET_CLUSTER_FROM_SECTOR(sec); + if (es->alloc_flag == 0x03) { + clu++; + } else { + if (exfat_fat_read(sb, clu, &clu) == -1) + goto err_out; + } + sec = START_SECTOR(clu); + } else { + sec++; + } + off = 0; + buf_off += copy_entries << DENTRY_SIZE_BITS; + } + } + + pr_debug("%s exited successfully\n", __func__); + return 0; +err_out: + pr_debug("%s failed\n", __func__); + return -EINVAL; +} + +/* write back all entries in entry set */ +static s32 write_whole_entry_set(struct super_block *sb, struct entry_set_cache_t *es) +{ + return __write_partial_entries_in_entry_set(sb, es, es->sector, + es->offset, + es->num_entries); } void update_dir_checksum_with_entry_set(struct super_block *sb, @@ -1562,7 +1215,7 @@ void update_dir_checksum_with_entry_set(struct super_block *sb, u16 chksum = 0; s32 chksum_type = CS_DIR_ENTRY, i; - ep = (struct dentry_t *)&(es->__buf); + ep = (struct dentry_t *)&es->__buf; for (i = 0; i < es->num_entries; i++) { pr_debug("%s ep %p\n", __func__, ep); chksum = calc_checksum_2byte((void *)ep, DENTRY_SIZE, chksum, @@ -1571,7 +1224,7 @@ void update_dir_checksum_with_entry_set(struct super_block *sb, chksum_type = CS_DEFAULT; } - ep = (struct dentry_t *)&(es->__buf); + ep = (struct dentry_t *)&es->__buf; SET16_A(((struct file_dentry_t *)ep)->checksum, chksum); write_whole_entry_set(sb, es); } @@ -1590,19 +1243,19 @@ static s32 _walk_fat_chain(struct super_block *sb, struct chain_t *p_dir, cur_clu += clu_offset; } else { while (clu_offset > 0) { - if (FAT_read(sb, cur_clu, &cur_clu) == -1) - return FFS_MEDIAERR; + if (exfat_fat_read(sb, cur_clu, &cur_clu) == -1) + return -EIO; clu_offset--; } } if (clu) *clu = cur_clu; - return FFS_SUCCESS; + return 0; } -s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, - sector_t *sector, s32 *offset) +static s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, + sector_t *sector, s32 *offset) { s32 off, ret; u32 clu = 0; @@ -1617,7 +1270,7 @@ s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, *sector += p_fs->root_start_sector; } else { ret = _walk_fat_chain(sb, p_dir, off, &clu); - if (ret != FFS_SUCCESS) + if (ret != 0) return ret; /* byte offset in cluster */ @@ -1630,20 +1283,7 @@ s32 find_location(struct super_block *sb, struct chain_t *p_dir, s32 entry, *sector = off >> p_bd->sector_size_bits; *sector += START_SECTOR(clu); } - return FFS_SUCCESS; -} - -struct dentry_t *get_entry_with_sector(struct super_block *sb, sector_t sector, - s32 offset) -{ - u8 *buf; - - buf = buf_getblk(sb, sector); - - if (!buf) - return NULL; - - return (struct dentry_t *)(buf + offset); + return 0; } struct dentry_t *get_entry_in_dir(struct super_block *sb, struct chain_t *p_dir, @@ -1653,10 +1293,10 @@ struct dentry_t *get_entry_in_dir(struct super_block *sb, struct chain_t *p_dir, sector_t sec; u8 *buf; - if (find_location(sb, p_dir, entry, &sec, &off) != FFS_SUCCESS) + if (find_location(sb, p_dir, entry, &sec, &off) != 0) return NULL; - buf = buf_getblk(sb, sec); + buf = exfat_buf_getblk(sb, sec); if (!buf) return NULL; @@ -1703,11 +1343,11 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, size_t bufsize; pr_debug("%s entered p_dir dir %u flags %x size %d\n", - __func__, p_dir->dir, p_dir->flags, p_dir->size); + __func__, p_dir->dir, p_dir->flags, p_dir->size); byte_offset = entry << DENTRY_SIZE_BITS; ret = _walk_fat_chain(sb, p_dir, byte_offset, &clu); - if (ret != FFS_SUCCESS) + if (ret != 0) return NULL; /* byte offset in cluster */ @@ -1720,15 +1360,14 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, sec = byte_offset >> p_bd->sector_size_bits; sec += START_SECTOR(clu); - buf = buf_getblk(sb, sec); + buf = exfat_buf_getblk(sb, sec); if (!buf) goto err_out; ep = (struct dentry_t *)(buf + off); - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); - if ((entry_type != TYPE_FILE) - && (entry_type != TYPE_DIR)) + if ((entry_type != TYPE_FILE) && (entry_type != TYPE_DIR)) goto err_out; if (type == ES_ALL_ENTRIES) @@ -1756,7 +1395,7 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, * instead of copying whole sector, we will check every entry. * this will provide minimum stablity and consistency. */ - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if ((entry_type == TYPE_UNUSED) || (entry_type == TYPE_DELETED)) goto err_out; @@ -1812,14 +1451,14 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, if (es->alloc_flag == 0x03) { clu++; } else { - if (FAT_read(sb, clu, &clu) == -1) + if (exfat_fat_read(sb, clu, &clu) == -1) goto err_out; } sec = START_SECTOR(clu); } else { sec++; } - buf = buf_getblk(sb, sec); + buf = exfat_buf_getblk(sb, sec); if (!buf) goto err_out; off = 0; @@ -1832,11 +1471,11 @@ struct entry_set_cache_t *get_entry_set_in_dir(struct super_block *sb, } if (file_ep) - *file_ep = (struct dentry_t *)&(es->__buf); + *file_ep = (struct dentry_t *)&es->__buf; pr_debug("%s exiting es %p sec %llu offset %d flags %d, num_entries %u buf ptr %p\n", - __func__, es, (unsigned long long)es->sector, es->offset, - es->alloc_flag, es->num_entries, &es->__buf); + __func__, es, (unsigned long long)es->sector, es->offset, + es->alloc_flag, es->num_entries, &es->__buf); return es; err_out: pr_debug("%s exited NULL (es %p)\n", __func__, es); @@ -1850,115 +1489,10 @@ void release_entry_set(struct entry_set_cache_t *es) kfree(es); } -static s32 __write_partial_entries_in_entry_set(struct super_block *sb, - struct entry_set_cache_t *es, - sector_t sec, s32 off, u32 count) -{ - s32 num_entries, buf_off = (off - es->offset); - u32 remaining_byte_in_sector, copy_entries; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - u32 clu; - u8 *buf, *esbuf = (u8 *)&(es->__buf); - - pr_debug("%s entered es %p sec %llu off %d count %d\n", - __func__, es, (unsigned long long)sec, off, count); - num_entries = count; - - while (num_entries) { - /* white per sector base */ - remaining_byte_in_sector = (1 << p_bd->sector_size_bits) - off; - copy_entries = min_t(s32, - remaining_byte_in_sector >> DENTRY_SIZE_BITS, - num_entries); - buf = buf_getblk(sb, sec); - if (!buf) - goto err_out; - pr_debug("es->buf %p buf_off %u\n", esbuf, buf_off); - pr_debug("copying %d entries from %p to sector %llu\n", - copy_entries, (esbuf + buf_off), - (unsigned long long)sec); - memcpy(buf + off, esbuf + buf_off, - copy_entries << DENTRY_SIZE_BITS); - buf_modify(sb, sec); - num_entries -= copy_entries; - - if (num_entries) { - /* get next sector */ - if (IS_LAST_SECTOR_IN_CLUSTER(sec)) { - clu = GET_CLUSTER_FROM_SECTOR(sec); - if (es->alloc_flag == 0x03) { - clu++; - } else { - if (FAT_read(sb, clu, &clu) == -1) - goto err_out; - } - sec = START_SECTOR(clu); - } else { - sec++; - } - off = 0; - buf_off += copy_entries << DENTRY_SIZE_BITS; - } - } - - pr_debug("%s exited successfully\n", __func__); - return FFS_SUCCESS; -err_out: - pr_debug("%s failed\n", __func__); - return FFS_ERROR; -} - -/* write back all entries in entry set */ -s32 write_whole_entry_set(struct super_block *sb, struct entry_set_cache_t *es) -{ - return __write_partial_entries_in_entry_set(sb, es, es->sector, - es->offset, - es->num_entries); -} - -/* write back some entries in entry set */ -s32 write_partial_entries_in_entry_set(struct super_block *sb, - struct entry_set_cache_t *es, struct dentry_t *ep, u32 count) -{ - s32 ret, byte_offset, off; - u32 clu = 0; - sector_t sec; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - struct chain_t dir; - - /* vaidity check */ - if (ep + count > ((struct dentry_t *)&(es->__buf)) + es->num_entries) - return FFS_ERROR; - - dir.dir = GET_CLUSTER_FROM_SECTOR(es->sector); - dir.flags = es->alloc_flag; - dir.size = 0xffffffff; /* XXX */ - - byte_offset = (es->sector - START_SECTOR(dir.dir)) << - p_bd->sector_size_bits; - byte_offset += ((void **)ep - &(es->__buf)) + es->offset; - - ret = _walk_fat_chain(sb, &dir, byte_offset, &clu); - if (ret != FFS_SUCCESS) - return ret; - - /* byte offset in cluster */ - byte_offset &= p_fs->cluster_size - 1; - - /* byte offset in sector */ - off = byte_offset & p_bd->sector_size_mask; - - /* sector offset in cluster */ - sec = byte_offset >> p_bd->sector_size_bits; - sec += START_SECTOR(clu); - return __write_partial_entries_in_entry_set(sb, es, sec, off, count); -} - -/* search EMPTY CONTINUOUS "num_entries" entries */ -s32 search_deleted_or_unused_entry(struct super_block *sb, - struct chain_t *p_dir, s32 num_entries) +/* search EMPTY CONTINUOUS "num_entries" entries */ +static s32 search_deleted_or_unused_entry(struct super_block *sb, + struct chain_t *p_dir, + s32 num_entries) { int i, dentry, num_empty = 0; s32 dentries_per_clu; @@ -2005,7 +1539,7 @@ s32 search_deleted_or_unused_entry(struct super_block *sb, if (!ep) return -1; - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) { num_empty++; @@ -2043,7 +1577,7 @@ s32 search_deleted_or_unused_entry(struct super_block *sb, else clu.dir = CLUSTER_32(~0); } else { - if (FAT_read(sb, clu.dir, &clu.dir) != 0) + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) return -1; } } @@ -2051,7 +1585,7 @@ s32 search_deleted_or_unused_entry(struct super_block *sb, return -1; } -s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries) +static s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries) { s32 ret, dentry; u32 last_clu; @@ -2070,10 +1604,8 @@ s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries if (p_fs->dev_ejected) break; - if (p_fs->vol_type == EXFAT) { - if (p_dir->dir != p_fs->root_dir) - size = i_size_read(inode); - } + if (p_dir->dir != p_fs->root_dir) + size = i_size_read(inode); last_clu = find_last_cluster(sb, p_dir); clu.dir = last_clu + 1; @@ -2081,12 +1613,12 @@ s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries clu.flags = p_dir->flags; /* (1) allocate a cluster */ - ret = p_fs->fs_func->alloc_cluster(sb, 1, &clu); + ret = exfat_alloc_cluster(sb, 1, &clu); if (ret < 1) - return -1; + return -EIO; - if (clear_cluster(sb, clu.dir) != FFS_SUCCESS) - return -1; + if (clear_cluster(sb, clu.dir) != 0) + return -EIO; /* (2) append to the FAT chain */ if (clu.flags != p_dir->flags) { @@ -2095,8 +1627,8 @@ s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries p_fs->hint_uentry.clu.flags = 0x01; } if (clu.flags == 0x01) - if (FAT_write(sb, last_clu, clu.dir) < 0) - return -1; + if (exfat_fat_write(sb, last_clu, clu.dir) < 0) + return -EIO; if (p_fs->hint_uentry.entry == -1) { p_fs->hint_uentry.dir = p_dir->dir; @@ -2110,21 +1642,19 @@ s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries p_dir->size++; /* (3) update the directory entry */ - if (p_fs->vol_type == EXFAT) { - if (p_dir->dir != p_fs->root_dir) { - size += p_fs->cluster_size; - - ep = get_entry_in_dir(sb, &fid->dir, - fid->entry + 1, §or); - if (!ep) - return -1; - p_fs->fs_func->set_entry_size(ep, size); - p_fs->fs_func->set_entry_flag(ep, p_dir->flags); - buf_modify(sb, sector); - - update_dir_checksum(sb, &(fid->dir), - fid->entry); - } + if (p_dir->dir != p_fs->root_dir) { + size += p_fs->cluster_size; + + ep = get_entry_in_dir(sb, &fid->dir, + fid->entry + 1, §or); + if (!ep) + return -ENOENT; + exfat_set_entry_size(ep, size); + exfat_set_entry_flag(ep, p_dir->flags); + exfat_buf_modify(sb, sector); + + update_dir_checksum(sb, &fid->dir, + fid->entry); } i_size_write(inode, i_size_read(inode) + p_fs->cluster_size); @@ -2137,102 +1667,21 @@ s32 find_empty_entry(struct inode *inode, struct chain_t *p_dir, s32 num_entries return dentry; } -/* return values of fat_find_dir_entry() - * >= 0 : return dir entiry position with the name in dir - * -1 : (root dir, ".") it is the root dir itself - * -2 : entry with the name does not exist - */ -s32 fat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, - struct uni_name_t *p_uniname, s32 num_entries, - struct dos_name_t *p_dosname, u32 type) +static s32 extract_uni_name_from_name_entry(struct name_dentry_t *ep, u16 *uniname, + s32 order) { - int i, dentry = 0, len; - s32 order = 0; - bool is_feasible_entry = true, has_ext_entry = false; - s32 dentries_per_clu; - u32 entry_type; - u16 entry_uniname[14], *uniname = NULL, unichar; - struct chain_t clu; - struct dentry_t *ep; - struct dos_dentry_t *dos_ep; - struct ext_dentry_t *ext_ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - if (p_dir->dir == p_fs->root_dir) { - if ((!nls_uniname_cmp(sb, p_uniname->name, - (u16 *)UNI_CUR_DIR_NAME)) || - (!nls_uniname_cmp(sb, p_uniname->name, - (u16 *)UNI_PAR_DIR_NAME))) - return -1; // special case, root directory itself - } - - if (p_dir->dir == CLUSTER_32(0)) /* FAT16 root_dir */ - dentries_per_clu = p_fs->dentries_in_root; - else - dentries_per_clu = p_fs->dentries_per_clu; - - clu.dir = p_dir->dir; - clu.flags = p_dir->flags; - - while (clu.dir != CLUSTER_32(~0)) { - if (p_fs->dev_ejected) - break; - - for (i = 0; i < dentries_per_clu; i++, dentry++) { - ep = get_entry_in_dir(sb, &clu, i, NULL); - if (!ep) - return -2; - - entry_type = p_fs->fs_func->get_entry_type(ep); - - if ((entry_type == TYPE_FILE) || (entry_type == TYPE_DIR)) { - if ((type == TYPE_ALL) || (type == entry_type)) { - if (is_feasible_entry && has_ext_entry) - return dentry; - - dos_ep = (struct dos_dentry_t *)ep; - if (!nls_dosname_cmp(sb, p_dosname->name, dos_ep->name)) - return dentry; - } - is_feasible_entry = true; - has_ext_entry = false; - } else if (entry_type == TYPE_EXTEND) { - if (is_feasible_entry) { - ext_ep = (struct ext_dentry_t *)ep; - if (ext_ep->order > 0x40) { - order = (s32)(ext_ep->order - 0x40); - uniname = p_uniname->name + 13 * (order - 1); - } else { - order = (s32)ext_ep->order; - uniname -= 13; - } - - len = extract_uni_name_from_ext_entry(ext_ep, entry_uniname, order); - - unichar = *(uniname + len); - *(uniname + len) = 0x0; - - if (nls_uniname_cmp(sb, uniname, entry_uniname)) - is_feasible_entry = false; - - *(uniname + len) = unichar; - } - has_ext_entry = true; - } else if (entry_type == TYPE_UNUSED) { - return -2; - } - is_feasible_entry = true; - has_ext_entry = false; - } - - if (p_dir->dir == CLUSTER_32(0)) - break; /* FAT16 root_dir */ + int i, len = 0; - if (FAT_read(sb, clu.dir, &clu.dir) != 0) - return -2; + for (i = 0; i < 30; i += 2) { + *uniname = GET16_A(ep->unicode_0_14 + i); + if (*uniname == 0x0) + return len; + uniname++; + len++; } - return -2; + *uniname = 0x0; + return len; } /* return values of exfat_find_dir_entry() @@ -2286,7 +1735,7 @@ s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, if (!ep) return -2; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); step = 1; if ((entry_type == TYPE_UNUSED) || (entry_type == TYPE_DELETED)) { @@ -2375,7 +1824,7 @@ s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, else clu.dir = CLUSTER_32(~0); } else { - if (FAT_read(sb, clu.dir, &clu.dir) != 0) + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) return -2; } } @@ -2383,36 +1832,6 @@ s32 exfat_find_dir_entry(struct super_block *sb, struct chain_t *p_dir, return -2; } -s32 fat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, - s32 entry, struct dentry_t *p_entry) -{ - s32 count = 0; - u8 chksum; - struct dos_dentry_t *dos_ep = (struct dos_dentry_t *)p_entry; - struct ext_dentry_t *ext_ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - chksum = calc_checksum_1byte((void *)dos_ep->name, DOS_NAME_LENGTH, 0); - - for (entry--; entry >= 0; entry--) { - ext_ep = (struct ext_dentry_t *)get_entry_in_dir(sb, p_dir, - entry, NULL); - if (!ext_ep) - return -1; - - if ((p_fs->fs_func->get_entry_type((struct dentry_t *)ext_ep) == - TYPE_EXTEND) && (ext_ep->checksum == chksum)) { - count++; - if (ext_ep->order > 0x40) - return count; - } else { - return count; - } - } - - return count; -} - s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, s32 entry, struct dentry_t *p_entry) { @@ -2420,14 +1839,13 @@ s32 exfat_count_ext_entries(struct super_block *sb, struct chain_t *p_dir, u32 type; struct file_dentry_t *file_ep = (struct file_dentry_t *)p_entry; struct dentry_t *ext_ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); for (i = 0, entry++; i < file_ep->num_ext; i++, entry++) { ext_ep = get_entry_in_dir(sb, p_dir, entry, NULL); if (!ext_ep) return -1; - type = p_fs->fs_func->get_entry_type(ext_ep); + type = exfat_get_entry_type(ext_ep); if ((type == TYPE_EXTEND) || (type == TYPE_STREAM)) count++; else @@ -2463,9 +1881,9 @@ s32 count_dos_name_entries(struct super_block *sb, struct chain_t *p_dir, for (i = 0; i < dentries_per_clu; i++) { ep = get_entry_in_dir(sb, &clu, i, NULL); if (!ep) - return -1; + return -ENOENT; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if (entry_type == TYPE_UNUSED) return count; @@ -2486,8 +1904,8 @@ s32 count_dos_name_entries(struct super_block *sb, struct chain_t *p_dir, else clu.dir = CLUSTER_32(~0); } else { - if (FAT_read(sb, clu.dir, &clu.dir) != 0) - return -1; + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) + return -EIO; } } @@ -2521,7 +1939,7 @@ bool is_dir_empty(struct super_block *sb, struct chain_t *p_dir) if (!ep) break; - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) return true; @@ -2546,7 +1964,7 @@ bool is_dir_empty(struct super_block *sb, struct chain_t *p_dir) else clu.dir = CLUSTER_32(~0); } - if (FAT_read(sb, clu.dir, &clu.dir) != 0) + if (exfat_fat_read(sb, clu.dir, &clu.dir) != 0) break; } @@ -2564,81 +1982,15 @@ s32 get_num_entries_and_dos_name(struct super_block *sb, struct chain_t *p_dir, struct uni_name_t *p_uniname, s32 *entries, struct dos_name_t *p_dosname) { - s32 ret, num_entries; - bool lossy = false; - char **r; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); + s32 num_entries; - num_entries = p_fs->fs_func->calc_num_entries(p_uniname); + num_entries = exfat_calc_num_entries(p_uniname); if (num_entries == 0) - return FFS_INVALIDPATH; - - if (p_fs->vol_type != EXFAT) { - nls_uniname_to_dosname(sb, p_dosname, p_uniname, &lossy); - - if (lossy) { - ret = fat_generate_dos_name(sb, p_dir, p_dosname); - if (ret) - return ret; - } else { - for (r = reserved_names; *r; r++) { - if (!strncmp((void *)p_dosname->name, *r, 8)) - return FFS_INVALIDPATH; - } - - if (p_dosname->name_case != 0xFF) - num_entries = 1; - } - - if (num_entries > 1) - p_dosname->name_case = 0x0; - } + return -EINVAL; *entries = num_entries; - return FFS_SUCCESS; -} - -void get_uni_name_from_dos_entry(struct super_block *sb, - struct dos_dentry_t *ep, - struct uni_name_t *p_uniname, u8 mode) -{ - struct dos_name_t dos_name; - - if (mode == 0x0) - dos_name.name_case = 0x0; - else - dos_name.name_case = ep->lcase; - - memcpy(dos_name.name, ep->name, DOS_NAME_LENGTH); - nls_dosname_to_uniname(sb, p_uniname, &dos_name); -} - -void fat_get_uni_name_from_ext_entry(struct super_block *sb, - struct chain_t *p_dir, s32 entry, - u16 *uniname) -{ - int i; - struct ext_dentry_t *ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - for (entry--, i = 1; entry >= 0; entry--, i++) { - ep = (struct ext_dentry_t *)get_entry_in_dir(sb, p_dir, entry, - NULL); - if (!ep) - return; - - if (p_fs->fs_func->get_entry_type((struct dentry_t *)ep) == - TYPE_EXTEND) { - extract_uni_name_from_ext_entry(ep, uniname, i); - if (ep->order > 0x40) - return; - } else { - return; - } - - uniname += 13; - } + return 0; } void exfat_get_uni_name_from_ext_entry(struct super_block *sb, @@ -2648,7 +2000,6 @@ void exfat_get_uni_name_from_ext_entry(struct super_block *sb, int i; struct dentry_t *ep; struct entry_set_cache_t *es; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); es = get_entry_set_in_dir(sb, p_dir, entry, ES_ALL_ENTRIES, &ep); if (!es || es->num_entries < 3) { @@ -2666,7 +2017,7 @@ void exfat_get_uni_name_from_ext_entry(struct super_block *sb, * So, the index of first file-name dentry should start from 2. */ for (i = 2; i < es->num_entries; i++, ep++) { - if (p_fs->fs_func->get_entry_type(ep) == TYPE_EXTEND) + if (exfat_get_entry_type(ep) == TYPE_EXTEND) extract_uni_name_from_name_entry((struct name_dentry_t *) ep, uniname, i); else @@ -2678,202 +2029,6 @@ out: release_entry_set(es); } -s32 extract_uni_name_from_ext_entry(struct ext_dentry_t *ep, u16 *uniname, - s32 order) -{ - int i, len = 0; - - for (i = 0; i < 10; i += 2) { - *uniname = GET16(ep->unicode_0_4 + i); - if (*uniname == 0x0) - return len; - uniname++; - len++; - } - - if (order < 20) { - for (i = 0; i < 12; i += 2) { - *uniname = GET16_A(ep->unicode_5_10 + i); - if (*uniname == 0x0) - return len; - uniname++; - len++; - } - } else { - for (i = 0; i < 8; i += 2) { - *uniname = GET16_A(ep->unicode_5_10 + i); - if (*uniname == 0x0) - return len; - uniname++; - len++; - } - *uniname = 0x0; /* uniname[MAX_NAME_LENGTH-1] */ - return len; - } - - for (i = 0; i < 4; i += 2) { - *uniname = GET16_A(ep->unicode_11_12 + i); - if (*uniname == 0x0) - return len; - uniname++; - len++; - } - - *uniname = 0x0; - return len; -} - -s32 extract_uni_name_from_name_entry(struct name_dentry_t *ep, u16 *uniname, - s32 order) -{ - int i, len = 0; - - for (i = 0; i < 30; i += 2) { - *uniname = GET16_A(ep->unicode_0_14 + i); - if (*uniname == 0x0) - return len; - uniname++; - len++; - } - - *uniname = 0x0; - return len; -} - -s32 fat_generate_dos_name(struct super_block *sb, struct chain_t *p_dir, - struct dos_name_t *p_dosname) -{ - int i, j, count = 0; - bool count_begin = false; - s32 dentries_per_clu; - u32 type; - u8 bmap[128/* 1 ~ 1023 */]; - struct chain_t clu; - struct dos_dentry_t *ep; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - - memset(bmap, 0, sizeof(bmap)); - exfat_bitmap_set(bmap, 0); - - if (p_dir->dir == CLUSTER_32(0)) /* FAT16 root_dir */ - dentries_per_clu = p_fs->dentries_in_root; - else - dentries_per_clu = p_fs->dentries_per_clu; - - clu.dir = p_dir->dir; - clu.flags = p_dir->flags; - - while (clu.dir != CLUSTER_32(~0)) { - if (p_fs->dev_ejected) - break; - - for (i = 0; i < dentries_per_clu; i++) { - ep = (struct dos_dentry_t *)get_entry_in_dir(sb, &clu, - i, NULL); - if (!ep) - return FFS_MEDIAERR; - - type = p_fs->fs_func->get_entry_type((struct dentry_t *) - ep); - - if (type == TYPE_UNUSED) - break; - if ((type != TYPE_FILE) && (type != TYPE_DIR)) - continue; - - count = 0; - count_begin = false; - - for (j = 0; j < 8; j++) { - if (ep->name[j] == ' ') - break; - - if (ep->name[j] == '~') { - count_begin = true; - } else if (count_begin) { - if ((ep->name[j] >= '0') && - (ep->name[j] <= '9')) { - count = count * 10 + - (ep->name[j] - '0'); - } else { - count = 0; - count_begin = false; - } - } - } - - if ((count > 0) && (count < 1024)) - exfat_bitmap_set(bmap, count); - } - - if (p_dir->dir == CLUSTER_32(0)) - break; /* FAT16 root_dir */ - - if (FAT_read(sb, clu.dir, &clu.dir) != 0) - return FFS_MEDIAERR; - } - - count = 0; - for (i = 0; i < 128; i++) { - if (bmap[i] != 0xFF) { - for (j = 0; j < 8; j++) { - if (exfat_bitmap_test(&bmap[i], j) == 0) { - count = (i << 3) + j; - break; - } - } - if (count != 0) - break; - } - } - - if ((count == 0) || (count >= 1024)) - return FFS_FILEEXIST; - fat_attach_count_to_dos_name(p_dosname->name, count); - - /* Now dos_name has DOS~????.EXT */ - return FFS_SUCCESS; -} - -void fat_attach_count_to_dos_name(u8 *dosname, s32 count) -{ - int i, j, length; - char str_count[6]; - - snprintf(str_count, sizeof(str_count), "~%d", count); - length = strlen(str_count); - - i = 0; - j = 0; - while (j <= (8 - length)) { - i = j; - if (dosname[j] == ' ') - break; - if (dosname[j] & 0x80) - j += 2; - else - j++; - } - - for (j = 0; j < length; i++, j++) - dosname[i] = (u8)str_count[j]; - - if (i == 7) - dosname[7] = ' '; -} - -s32 fat_calc_num_entries(struct uni_name_t *p_uniname) -{ - s32 len; - - len = p_uniname->name_len; - if (len == 0) - return 0; - - /* 1 dos name entry + extended entries */ - return (len - 1) / 13 + 2; -} - s32 exfat_calc_num_entries(struct uni_name_t *p_uniname) { s32 len; @@ -2886,17 +2041,6 @@ s32 exfat_calc_num_entries(struct uni_name_t *p_uniname) return (len - 1) / 15 + 3; } -u8 calc_checksum_1byte(void *data, s32 len, u8 chksum) -{ - int i; - u8 *c = (u8 *)data; - - for (i = 0; i < len; i++, c++) - chksum = (((chksum & 1) << 7) | ((chksum & 0xFE) >> 1)) + *c; - - return chksum; -} - u16 calc_checksum_2byte(void *data, s32 len, u16 chksum, s32 type) { int i; @@ -2921,30 +2065,6 @@ u16 calc_checksum_2byte(void *data, s32 len, u16 chksum, s32 type) return chksum; } -u32 calc_checksum_4byte(void *data, s32 len, u32 chksum, s32 type) -{ - int i; - u8 *c = (u8 *)data; - - switch (type) { - case CS_PBR_SECTOR: - for (i = 0; i < len; i++, c++) { - if ((i == 106) || (i == 107) || (i == 112)) - continue; - chksum = (((chksum & 1) << 31) | - ((chksum & 0xFFFFFFFE) >> 1)) + (u32)*c; - } - break; - default - : - for (i = 0; i < len; i++, c++) - chksum = (((chksum & 1) << 31) | - ((chksum & 0xFFFFFFFE) >> 1)) + (u32)*c; - } - - return chksum; -} - /* * Name Resolution Functions */ @@ -2962,11 +2082,11 @@ s32 resolve_path(struct inode *inode, char *path, struct chain_t *p_dir, struct file_id_t *fid = &(EXFAT_I(inode)->fid); if (strscpy(name_buf, path, sizeof(name_buf)) < 0) - return FFS_INVALIDPATH; + return -EINVAL; nls_cstring_to_uniname(sb, p_uniname, name_buf, &lossy); if (lossy) - return FFS_INVALIDPATH; + return -EINVAL; fid->size = i_size_read(inode); @@ -2974,181 +2094,9 @@ s32 resolve_path(struct inode *inode, char *path, struct chain_t *p_dir, p_dir->size = (s32)(fid->size >> p_fs->cluster_size_bits); p_dir->flags = fid->flags; - return FFS_SUCCESS; -} - -/* - * File Operation Functions - */ -static struct fs_func fat_fs_func = { - .alloc_cluster = fat_alloc_cluster, - .free_cluster = fat_free_cluster, - .count_used_clusters = fat_count_used_clusters, - - .init_dir_entry = fat_init_dir_entry, - .init_ext_entry = fat_init_ext_entry, - .find_dir_entry = fat_find_dir_entry, - .delete_dir_entry = fat_delete_dir_entry, - .get_uni_name_from_ext_entry = fat_get_uni_name_from_ext_entry, - .count_ext_entries = fat_count_ext_entries, - .calc_num_entries = fat_calc_num_entries, - - .get_entry_type = fat_get_entry_type, - .set_entry_type = fat_set_entry_type, - .get_entry_attr = fat_get_entry_attr, - .set_entry_attr = fat_set_entry_attr, - .get_entry_flag = fat_get_entry_flag, - .set_entry_flag = fat_set_entry_flag, - .get_entry_clu0 = fat_get_entry_clu0, - .set_entry_clu0 = fat_set_entry_clu0, - .get_entry_size = fat_get_entry_size, - .set_entry_size = fat_set_entry_size, - .get_entry_time = fat_get_entry_time, - .set_entry_time = fat_set_entry_time, -}; - -s32 fat16_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) -{ - s32 num_reserved, num_root_sectors; - struct bpb16_t *p_bpb = (struct bpb16_t *)p_pbr->bpb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - - if (p_bpb->num_fats == 0) - return FFS_FORMATERR; - - num_root_sectors = GET16(p_bpb->num_root_entries) << DENTRY_SIZE_BITS; - num_root_sectors = ((num_root_sectors - 1) >> - p_bd->sector_size_bits) + 1; - - p_fs->sectors_per_clu = p_bpb->sectors_per_clu; - p_fs->sectors_per_clu_bits = ilog2(p_bpb->sectors_per_clu); - p_fs->cluster_size_bits = p_fs->sectors_per_clu_bits + - p_bd->sector_size_bits; - p_fs->cluster_size = 1 << p_fs->cluster_size_bits; - - p_fs->num_FAT_sectors = GET16(p_bpb->num_fat_sectors); - - p_fs->FAT1_start_sector = p_fs->PBR_sector + GET16(p_bpb->num_reserved); - if (p_bpb->num_fats == 1) - p_fs->FAT2_start_sector = p_fs->FAT1_start_sector; - else - p_fs->FAT2_start_sector = p_fs->FAT1_start_sector + - p_fs->num_FAT_sectors; - - p_fs->root_start_sector = p_fs->FAT2_start_sector + - p_fs->num_FAT_sectors; - p_fs->data_start_sector = p_fs->root_start_sector + num_root_sectors; - - p_fs->num_sectors = GET16(p_bpb->num_sectors); - if (p_fs->num_sectors == 0) - p_fs->num_sectors = GET32(p_bpb->num_huge_sectors); - - num_reserved = p_fs->data_start_sector - p_fs->PBR_sector; - p_fs->num_clusters = ((p_fs->num_sectors - num_reserved) >> - p_fs->sectors_per_clu_bits) + 2; - /* because the cluster index starts with 2 */ - - if (p_fs->num_clusters < FAT12_THRESHOLD) - p_fs->vol_type = FAT12; - else - p_fs->vol_type = FAT16; - p_fs->vol_id = GET32(p_bpb->vol_serial); - - p_fs->root_dir = 0; - p_fs->dentries_in_root = GET16(p_bpb->num_root_entries); - p_fs->dentries_per_clu = 1 << (p_fs->cluster_size_bits - - DENTRY_SIZE_BITS); - - p_fs->vol_flag = VOL_CLEAN; - p_fs->clu_srch_ptr = 2; - p_fs->used_clusters = UINT_MAX; - - p_fs->fs_func = &fat_fs_func; - - return FFS_SUCCESS; + return 0; } -s32 fat32_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) -{ - s32 num_reserved; - struct bpb32_t *p_bpb = (struct bpb32_t *)p_pbr->bpb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); - - if (p_bpb->num_fats == 0) - return FFS_FORMATERR; - - p_fs->sectors_per_clu = p_bpb->sectors_per_clu; - p_fs->sectors_per_clu_bits = ilog2(p_bpb->sectors_per_clu); - p_fs->cluster_size_bits = p_fs->sectors_per_clu_bits + - p_bd->sector_size_bits; - p_fs->cluster_size = 1 << p_fs->cluster_size_bits; - - p_fs->num_FAT_sectors = GET32(p_bpb->num_fat32_sectors); - - p_fs->FAT1_start_sector = p_fs->PBR_sector + GET16(p_bpb->num_reserved); - if (p_bpb->num_fats == 1) - p_fs->FAT2_start_sector = p_fs->FAT1_start_sector; - else - p_fs->FAT2_start_sector = p_fs->FAT1_start_sector + - p_fs->num_FAT_sectors; - - p_fs->root_start_sector = p_fs->FAT2_start_sector + - p_fs->num_FAT_sectors; - p_fs->data_start_sector = p_fs->root_start_sector; - - p_fs->num_sectors = GET32(p_bpb->num_huge_sectors); - num_reserved = p_fs->data_start_sector - p_fs->PBR_sector; - - p_fs->num_clusters = ((p_fs->num_sectors - num_reserved) >> - p_fs->sectors_per_clu_bits) + 2; - /* because the cluster index starts with 2 */ - - p_fs->vol_type = FAT32; - p_fs->vol_id = GET32(p_bpb->vol_serial); - - p_fs->root_dir = GET32(p_bpb->root_cluster); - p_fs->dentries_in_root = 0; - p_fs->dentries_per_clu = 1 << (p_fs->cluster_size_bits - - DENTRY_SIZE_BITS); - - p_fs->vol_flag = VOL_CLEAN; - p_fs->clu_srch_ptr = 2; - p_fs->used_clusters = UINT_MAX; - - p_fs->fs_func = &fat_fs_func; - - return FFS_SUCCESS; -} - -static struct fs_func exfat_fs_func = { - .alloc_cluster = exfat_alloc_cluster, - .free_cluster = exfat_free_cluster, - .count_used_clusters = exfat_count_used_clusters, - - .init_dir_entry = exfat_init_dir_entry, - .init_ext_entry = exfat_init_ext_entry, - .find_dir_entry = exfat_find_dir_entry, - .delete_dir_entry = exfat_delete_dir_entry, - .get_uni_name_from_ext_entry = exfat_get_uni_name_from_ext_entry, - .count_ext_entries = exfat_count_ext_entries, - .calc_num_entries = exfat_calc_num_entries, - - .get_entry_type = exfat_get_entry_type, - .set_entry_type = exfat_set_entry_type, - .get_entry_attr = exfat_get_entry_attr, - .set_entry_attr = exfat_set_entry_attr, - .get_entry_flag = exfat_get_entry_flag, - .set_entry_flag = exfat_set_entry_flag, - .get_entry_clu0 = exfat_get_entry_clu0, - .set_entry_clu0 = exfat_set_entry_clu0, - .get_entry_size = exfat_get_entry_size, - .set_entry_size = exfat_set_entry_size, - .get_entry_time = exfat_get_entry_time, - .set_entry_time = exfat_set_entry_time, -}; - s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) { struct bpbex_t *p_bpb = (struct bpbex_t *)p_pbr->bpb; @@ -3156,7 +2104,7 @@ s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); if (p_bpb->num_fats == 0) - return FFS_FORMATERR; + return -EFSCORRUPTED; p_fs->sectors_per_clu = 1 << p_bpb->sectors_per_clu_bits; p_fs->sectors_per_clu_bits = p_bpb->sectors_per_clu_bits; @@ -3192,9 +2140,7 @@ s32 exfat_mount(struct super_block *sb, struct pbr_sector_t *p_pbr) p_fs->clu_srch_ptr = 2; p_fs->used_clusters = UINT_MAX; - p_fs->fs_func = &exfat_fs_func; - - return FFS_SUCCESS; + return 0; } s32 create_dir(struct inode *inode, struct chain_t *p_dir, @@ -3203,10 +2149,9 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, s32 ret, dentry, num_entries; u64 size; struct chain_t clu; - struct dos_name_t dos_name, dot_name; + struct dos_name_t dos_name; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ret = get_num_entries_and_dos_name(sb, p_dir, p_uniname, &num_entries, &dos_name); @@ -3216,73 +2161,35 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, /* find_empty_entry must be called before alloc_cluster */ dentry = find_empty_entry(inode, p_dir, num_entries); if (dentry < 0) - return FFS_FULL; + return -ENOSPC; clu.dir = CLUSTER_32(~0); clu.size = 0; clu.flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; /* (1) allocate a cluster */ - ret = fs_func->alloc_cluster(sb, 1, &clu); + ret = exfat_alloc_cluster(sb, 1, &clu); if (ret < 0) - return FFS_MEDIAERR; + return ret; else if (ret == 0) - return FFS_FULL; + return -ENOSPC; ret = clear_cluster(sb, clu.dir); - if (ret != FFS_SUCCESS) + if (ret != 0) return ret; - if (p_fs->vol_type == EXFAT) { - size = p_fs->cluster_size; - } else { - size = 0; - - /* initialize the . and .. entry - * Information for . points to itself - * Information for .. points to parent dir - */ - - dot_name.name_case = 0x0; - memcpy(dot_name.name, DOS_CUR_DIR_NAME, DOS_NAME_LENGTH); - - ret = fs_func->init_dir_entry(sb, &clu, 0, TYPE_DIR, clu.dir, - 0); - if (ret != FFS_SUCCESS) - return ret; - - ret = fs_func->init_ext_entry(sb, &clu, 0, 1, NULL, &dot_name); - if (ret != FFS_SUCCESS) - return ret; - - memcpy(dot_name.name, DOS_PAR_DIR_NAME, DOS_NAME_LENGTH); - - if (p_dir->dir == p_fs->root_dir) - ret = fs_func->init_dir_entry(sb, &clu, 1, TYPE_DIR, - CLUSTER_32(0), 0); - else - ret = fs_func->init_dir_entry(sb, &clu, 1, TYPE_DIR, - p_dir->dir, 0); - - if (ret != FFS_SUCCESS) - return ret; - - ret = p_fs->fs_func->init_ext_entry(sb, &clu, 1, 1, NULL, - &dot_name); - if (ret != FFS_SUCCESS) - return ret; - } + size = p_fs->cluster_size; /* (2) update the directory entry */ /* make sub-dir entry in parent directory */ - ret = fs_func->init_dir_entry(sb, p_dir, dentry, TYPE_DIR, clu.dir, - size); - if (ret != FFS_SUCCESS) + ret = exfat_init_dir_entry(sb, p_dir, dentry, TYPE_DIR, clu.dir, + size); + if (ret != 0) return ret; - ret = fs_func->init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, - &dos_name); - if (ret != FFS_SUCCESS) + ret = exfat_init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, + &dos_name); + if (ret != 0) return ret; fid->dir.dir = p_dir->dir; @@ -3299,7 +2206,7 @@ s32 create_dir(struct inode *inode, struct chain_t *p_dir, fid->rwoffset = 0; fid->hint_last_off = -1; - return FFS_SUCCESS; + return 0; } s32 create_file(struct inode *inode, struct chain_t *p_dir, @@ -3309,7 +2216,6 @@ s32 create_file(struct inode *inode, struct chain_t *p_dir, struct dos_name_t dos_name; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ret = get_num_entries_and_dos_name(sb, p_dir, p_uniname, &num_entries, &dos_name); @@ -3319,20 +2225,20 @@ s32 create_file(struct inode *inode, struct chain_t *p_dir, /* find_empty_entry must be called before alloc_cluster() */ dentry = find_empty_entry(inode, p_dir, num_entries); if (dentry < 0) - return FFS_FULL; + return -ENOSPC; /* (1) update the directory entry */ /* fill the dos name directory entry information of the created file. * the first cluster is not determined yet. (0) */ - ret = fs_func->init_dir_entry(sb, p_dir, dentry, TYPE_FILE | mode, - CLUSTER_32(0), 0); - if (ret != FFS_SUCCESS) + ret = exfat_init_dir_entry(sb, p_dir, dentry, TYPE_FILE | mode, + CLUSTER_32(0), 0); + if (ret != 0) return ret; - ret = fs_func->init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, - &dos_name); - if (ret != FFS_SUCCESS) + ret = exfat_init_ext_entry(sb, p_dir, dentry, num_entries, p_uniname, + &dos_name); + if (ret != 0) return ret; fid->dir.dir = p_dir->dir; @@ -3349,7 +2255,7 @@ s32 create_file(struct inode *inode, struct chain_t *p_dir, fid->rwoffset = 0; fid->hint_last_off = -1; - return FFS_SUCCESS; + return 0; } void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry) @@ -3358,27 +2264,25 @@ void remove_file(struct inode *inode, struct chain_t *p_dir, s32 entry) sector_t sector; struct dentry_t *ep; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; ep = get_entry_in_dir(sb, p_dir, entry, §or); if (!ep) return; - buf_lock(sb, sector); + exfat_buf_lock(sb, sector); - /* buf_lock() before call count_ext_entries() */ - num_entries = fs_func->count_ext_entries(sb, p_dir, entry, ep); + /* exfat_buf_lock() before call count_ext_entries() */ + num_entries = exfat_count_ext_entries(sb, p_dir, entry, ep); if (num_entries < 0) { - buf_unlock(sb, sector); + exfat_buf_unlock(sb, sector); return; } num_entries++; - buf_unlock(sb, sector); + exfat_buf_unlock(sb, sector); /* (1) update the directory entry */ - fs_func->delete_dir_entry(sb, p_dir, entry, 0, num_entries); + exfat_delete_dir_entry(sb, p_dir, entry, 0, num_entries); } s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, @@ -3389,101 +2293,97 @@ s32 exfat_rename_file(struct inode *inode, struct chain_t *p_dir, s32 oldentry, struct dos_name_t dos_name; struct dentry_t *epold, *epnew; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; epold = get_entry_in_dir(sb, p_dir, oldentry, §or_old); if (!epold) - return FFS_MEDIAERR; + return -ENOENT; - buf_lock(sb, sector_old); + exfat_buf_lock(sb, sector_old); - /* buf_lock() before call count_ext_entries() */ - num_old_entries = fs_func->count_ext_entries(sb, p_dir, oldentry, - epold); + /* exfat_buf_lock() before call count_ext_entries() */ + num_old_entries = exfat_count_ext_entries(sb, p_dir, oldentry, + epold); if (num_old_entries < 0) { - buf_unlock(sb, sector_old); - return FFS_MEDIAERR; + exfat_buf_unlock(sb, sector_old); + return -ENOENT; } num_old_entries++; ret = get_num_entries_and_dos_name(sb, p_dir, p_uniname, &num_new_entries, &dos_name); if (ret) { - buf_unlock(sb, sector_old); + exfat_buf_unlock(sb, sector_old); return ret; } if (num_old_entries < num_new_entries) { newentry = find_empty_entry(inode, p_dir, num_new_entries); if (newentry < 0) { - buf_unlock(sb, sector_old); - return FFS_FULL; + exfat_buf_unlock(sb, sector_old); + return -ENOSPC; } epnew = get_entry_in_dir(sb, p_dir, newentry, §or_new); if (!epnew) { - buf_unlock(sb, sector_old); - return FFS_MEDIAERR; + exfat_buf_unlock(sb, sector_old); + return -ENOENT; } memcpy((void *)epnew, (void *)epold, DENTRY_SIZE); - if (fs_func->get_entry_type(epnew) == TYPE_FILE) { - fs_func->set_entry_attr(epnew, - fs_func->get_entry_attr(epnew) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epnew) == TYPE_FILE) { + exfat_set_entry_attr(epnew, + exfat_get_entry_attr(epnew) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } - buf_modify(sb, sector_new); - buf_unlock(sb, sector_old); - - if (p_fs->vol_type == EXFAT) { - epold = get_entry_in_dir(sb, p_dir, oldentry + 1, - §or_old); - buf_lock(sb, sector_old); - epnew = get_entry_in_dir(sb, p_dir, newentry + 1, - §or_new); - - if (!epold || !epnew) { - buf_unlock(sb, sector_old); - return FFS_MEDIAERR; - } + exfat_buf_modify(sb, sector_new); + exfat_buf_unlock(sb, sector_old); + + epold = get_entry_in_dir(sb, p_dir, oldentry + 1, + §or_old); + exfat_buf_lock(sb, sector_old); + epnew = get_entry_in_dir(sb, p_dir, newentry + 1, + §or_new); - memcpy((void *)epnew, (void *)epold, DENTRY_SIZE); - buf_modify(sb, sector_new); - buf_unlock(sb, sector_old); + if (!epold || !epnew) { + exfat_buf_unlock(sb, sector_old); + return -ENOENT; } - ret = fs_func->init_ext_entry(sb, p_dir, newentry, - num_new_entries, p_uniname, - &dos_name); - if (ret != FFS_SUCCESS) + memcpy((void *)epnew, (void *)epold, DENTRY_SIZE); + exfat_buf_modify(sb, sector_new); + exfat_buf_unlock(sb, sector_old); + + ret = exfat_init_ext_entry(sb, p_dir, newentry, + num_new_entries, p_uniname, + &dos_name); + if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_dir, oldentry, 0, - num_old_entries); + exfat_delete_dir_entry(sb, p_dir, oldentry, 0, + num_old_entries); fid->entry = newentry; } else { - if (fs_func->get_entry_type(epold) == TYPE_FILE) { - fs_func->set_entry_attr(epold, - fs_func->get_entry_attr(epold) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epold) == TYPE_FILE) { + exfat_set_entry_attr(epold, + exfat_get_entry_attr(epold) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } - buf_modify(sb, sector_old); - buf_unlock(sb, sector_old); + exfat_buf_modify(sb, sector_old); + exfat_buf_unlock(sb, sector_old); - ret = fs_func->init_ext_entry(sb, p_dir, oldentry, - num_new_entries, p_uniname, - &dos_name); - if (ret != FFS_SUCCESS) + ret = exfat_init_ext_entry(sb, p_dir, oldentry, + num_new_entries, p_uniname, + &dos_name); + if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_dir, oldentry, num_new_entries, - num_old_entries); + exfat_delete_dir_entry(sb, p_dir, oldentry, num_new_entries, + num_old_entries); } - return FFS_SUCCESS; + return 0; } s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, @@ -3492,97 +2392,78 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, { s32 ret, newentry, num_new_entries, num_old_entries; sector_t sector_mov, sector_new; - struct chain_t clu; struct dos_name_t dos_name; struct dentry_t *epmov, *epnew; struct super_block *sb = inode->i_sb; - struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; epmov = get_entry_in_dir(sb, p_olddir, oldentry, §or_mov); if (!epmov) - return FFS_MEDIAERR; + return -ENOENT; /* check if the source and target directory is the same */ - if (fs_func->get_entry_type(epmov) == TYPE_DIR && - fs_func->get_entry_clu0(epmov) == p_newdir->dir) - return FFS_INVALIDPATH; + if (exfat_get_entry_type(epmov) == TYPE_DIR && + exfat_get_entry_clu0(epmov) == p_newdir->dir) + return -EINVAL; - buf_lock(sb, sector_mov); + exfat_buf_lock(sb, sector_mov); - /* buf_lock() before call count_ext_entries() */ - num_old_entries = fs_func->count_ext_entries(sb, p_olddir, oldentry, - epmov); + /* exfat_buf_lock() before call count_ext_entries() */ + num_old_entries = exfat_count_ext_entries(sb, p_olddir, oldentry, + epmov); if (num_old_entries < 0) { - buf_unlock(sb, sector_mov); - return FFS_MEDIAERR; + exfat_buf_unlock(sb, sector_mov); + return -ENOENT; } num_old_entries++; ret = get_num_entries_and_dos_name(sb, p_newdir, p_uniname, &num_new_entries, &dos_name); if (ret) { - buf_unlock(sb, sector_mov); + exfat_buf_unlock(sb, sector_mov); return ret; } newentry = find_empty_entry(inode, p_newdir, num_new_entries); if (newentry < 0) { - buf_unlock(sb, sector_mov); - return FFS_FULL; + exfat_buf_unlock(sb, sector_mov); + return -ENOSPC; } epnew = get_entry_in_dir(sb, p_newdir, newentry, §or_new); if (!epnew) { - buf_unlock(sb, sector_mov); - return FFS_MEDIAERR; + exfat_buf_unlock(sb, sector_mov); + return -ENOENT; } memcpy((void *)epnew, (void *)epmov, DENTRY_SIZE); - if (fs_func->get_entry_type(epnew) == TYPE_FILE) { - fs_func->set_entry_attr(epnew, fs_func->get_entry_attr(epnew) | - ATTR_ARCHIVE); + if (exfat_get_entry_type(epnew) == TYPE_FILE) { + exfat_set_entry_attr(epnew, exfat_get_entry_attr(epnew) | + ATTR_ARCHIVE); fid->attr |= ATTR_ARCHIVE; } - buf_modify(sb, sector_new); - buf_unlock(sb, sector_mov); - - if (p_fs->vol_type == EXFAT) { - epmov = get_entry_in_dir(sb, p_olddir, oldentry + 1, - §or_mov); - buf_lock(sb, sector_mov); - epnew = get_entry_in_dir(sb, p_newdir, newentry + 1, - §or_new); - if (!epmov || !epnew) { - buf_unlock(sb, sector_mov); - return FFS_MEDIAERR; - } + exfat_buf_modify(sb, sector_new); + exfat_buf_unlock(sb, sector_mov); - memcpy((void *)epnew, (void *)epmov, DENTRY_SIZE); - buf_modify(sb, sector_new); - buf_unlock(sb, sector_mov); - } else if (fs_func->get_entry_type(epnew) == TYPE_DIR) { - /* change ".." pointer to new parent dir */ - clu.dir = fs_func->get_entry_clu0(epnew); - clu.flags = 0x01; - - epnew = get_entry_in_dir(sb, &clu, 1, §or_new); - if (!epnew) - return FFS_MEDIAERR; - - if (p_newdir->dir == p_fs->root_dir) - fs_func->set_entry_clu0(epnew, CLUSTER_32(0)); - else - fs_func->set_entry_clu0(epnew, p_newdir->dir); - buf_modify(sb, sector_new); + epmov = get_entry_in_dir(sb, p_olddir, oldentry + 1, + §or_mov); + exfat_buf_lock(sb, sector_mov); + epnew = get_entry_in_dir(sb, p_newdir, newentry + 1, + §or_new); + if (!epmov || !epnew) { + exfat_buf_unlock(sb, sector_mov); + return -ENOENT; } - ret = fs_func->init_ext_entry(sb, p_newdir, newentry, num_new_entries, - p_uniname, &dos_name); - if (ret != FFS_SUCCESS) + memcpy((void *)epnew, (void *)epmov, DENTRY_SIZE); + exfat_buf_modify(sb, sector_new); + exfat_buf_unlock(sb, sector_mov); + + ret = exfat_init_ext_entry(sb, p_newdir, newentry, num_new_entries, + p_uniname, &dos_name); + if (ret != 0) return ret; - fs_func->delete_dir_entry(sb, p_olddir, oldentry, 0, num_old_entries); + exfat_delete_dir_entry(sb, p_olddir, oldentry, 0, num_old_entries); fid->dir.dir = p_newdir->dir; fid->dir.size = p_newdir->size; @@ -3590,7 +2471,7 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, fid->entry = newentry; - return FFS_SUCCESS; + return 0; } /* @@ -3600,7 +2481,7 @@ s32 move_file(struct inode *inode, struct chain_t *p_olddir, s32 oldentry, int sector_read(struct super_block *sb, sector_t sec, struct buffer_head **bh, bool read) { - s32 ret = FFS_MEDIAERR; + s32 ret = -EIO; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); if ((sec >= (p_fs->PBR_sector + p_fs->num_sectors)) && @@ -3612,8 +2493,8 @@ int sector_read(struct super_block *sb, sector_t sec, struct buffer_head **bh, } if (!p_fs->dev_ejected) { - ret = bdev_read(sb, sec, bh, 1, read); - if (ret != FFS_SUCCESS) + ret = exfat_bdev_read(sb, sec, bh, 1, read); + if (ret != 0) p_fs->dev_ejected = 1; } @@ -3623,7 +2504,7 @@ int sector_read(struct super_block *sb, sector_t sec, struct buffer_head **bh, int sector_write(struct super_block *sb, sector_t sec, struct buffer_head *bh, bool sync) { - s32 ret = FFS_MEDIAERR; + s32 ret = -EIO; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); if (sec >= (p_fs->PBR_sector + p_fs->num_sectors) && @@ -3641,8 +2522,8 @@ int sector_write(struct super_block *sb, sector_t sec, struct buffer_head *bh, } if (!p_fs->dev_ejected) { - ret = bdev_write(sb, sec, bh, 1, sync); - if (ret != FFS_SUCCESS) + ret = exfat_bdev_write(sb, sec, bh, 1, sync); + if (ret != 0) p_fs->dev_ejected = 1; } @@ -3652,7 +2533,7 @@ int sector_write(struct super_block *sb, sector_t sec, struct buffer_head *bh, int multi_sector_read(struct super_block *sb, sector_t sec, struct buffer_head **bh, s32 num_secs, bool read) { - s32 ret = FFS_MEDIAERR; + s32 ret = -EIO; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); if (((sec + num_secs) > (p_fs->PBR_sector + p_fs->num_sectors)) && @@ -3664,8 +2545,8 @@ int multi_sector_read(struct super_block *sb, sector_t sec, } if (!p_fs->dev_ejected) { - ret = bdev_read(sb, sec, bh, num_secs, read); - if (ret != FFS_SUCCESS) + ret = exfat_bdev_read(sb, sec, bh, num_secs, read); + if (ret != 0) p_fs->dev_ejected = 1; } @@ -3675,7 +2556,7 @@ int multi_sector_read(struct super_block *sb, sector_t sec, int multi_sector_write(struct super_block *sb, sector_t sec, struct buffer_head *bh, s32 num_secs, bool sync) { - s32 ret = FFS_MEDIAERR; + s32 ret = -EIO; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); if ((sec + num_secs) > (p_fs->PBR_sector + p_fs->num_sectors) && @@ -3692,8 +2573,8 @@ int multi_sector_write(struct super_block *sb, sector_t sec, } if (!p_fs->dev_ejected) { - ret = bdev_write(sb, sec, bh, num_secs, sync); - if (ret != FFS_SUCCESS) + ret = exfat_bdev_write(sb, sec, bh, num_secs, sync); + if (ret != 0) p_fs->dev_ejected = 1; } diff --git a/drivers/staging/exfat/exfat_nls.c b/drivers/staging/exfat/exfat_nls.c index a5c4b68..91e8b0c 100644 --- a/drivers/staging/exfat/exfat_nls.c +++ b/drivers/staging/exfat/exfat_nls.c @@ -7,13 +7,6 @@ #include #include "exfat.h" -static u16 bad_dos_chars[] = { - /* + , ; = [ ] */ - 0x002B, 0x002C, 0x003B, 0x003D, 0x005B, 0x005D, - 0xFF0B, 0xFF0C, 0xFF1B, 0xFF1D, 0xFF3B, 0xFF3D, - 0 -}; - static u16 bad_uni_chars[] = { /* " * / : < > ? \ | */ 0x0022, 0x002A, 0x002F, 0x003A, @@ -96,11 +89,6 @@ static u16 *nls_wstrchr(u16 *str, u16 wchar) return NULL; } -int nls_dosname_cmp(struct super_block *sb, u8 *a, u8 *b) -{ - return strncmp(a, b, DOS_NAME_LENGTH); -} - int nls_uniname_cmp(struct super_block *sb, u16 *a, u16 *b) { int i; @@ -114,186 +102,6 @@ int nls_uniname_cmp(struct super_block *sb, u16 *a, u16 *b) return 0; } -void nls_uniname_to_dosname(struct super_block *sb, - struct dos_name_t *p_dosname, - struct uni_name_t *p_uniname, bool *p_lossy) -{ - int i, j, len; - bool lossy = false; - u8 buf[MAX_CHARSET_SIZE]; - u8 lower = 0, upper = 0; - u8 *dosname = p_dosname->name; - u16 *uniname = p_uniname->name; - u16 *p, *last_period; - struct nls_table *nls = EXFAT_SB(sb)->nls_disk; - - for (i = 0; i < DOS_NAME_LENGTH; i++) - *(dosname + i) = ' '; - - if (!nls_uniname_cmp(sb, uniname, (u16 *)UNI_CUR_DIR_NAME)) { - *(dosname) = '.'; - p_dosname->name_case = 0x0; - if (p_lossy) - *p_lossy = false; - return; - } - - if (!nls_uniname_cmp(sb, uniname, (u16 *)UNI_PAR_DIR_NAME)) { - *(dosname) = '.'; - *(dosname + 1) = '.'; - p_dosname->name_case = 0x0; - if (p_lossy) - *p_lossy = false; - return; - } - - /* search for the last embedded period */ - last_period = NULL; - for (p = uniname; *p; p++) { - if (*p == (u16)'.') - last_period = p; - } - - i = 0; - while (i < DOS_NAME_LENGTH) { - if (i == 8) { - if (!last_period) - break; - - if (uniname <= last_period) { - if (uniname < last_period) - lossy = true; - uniname = last_period + 1; - } - } - - if (*uniname == (u16)'\0') { - break; - } else if (*uniname == (u16)' ') { - lossy = true; - } else if (*uniname == (u16)'.') { - if (uniname < last_period) - lossy = true; - else - i = 8; - } else if (nls_wstrchr(bad_dos_chars, *uniname)) { - lossy = true; - *(dosname + i) = '_'; - i++; - } else { - len = convert_uni_to_ch(nls, buf, *uniname, &lossy); - - if (len > 1) { - if ((i >= 8) && ((i + len) > DOS_NAME_LENGTH)) - break; - - if ((i < 8) && ((i + len) > 8)) { - i = 8; - continue; - } - - lower = 0xFF; - - for (j = 0; j < len; j++, i++) - *(dosname + i) = *(buf + j); - } else { /* len == 1 */ - if ((*buf >= 'a') && (*buf <= 'z')) { - *(dosname + i) = *buf - ('a' - 'A'); - - if (i < 8) - lower |= 0x08; - else - lower |= 0x10; - } else if ((*buf >= 'A') && (*buf <= 'Z')) { - *(dosname + i) = *buf; - - if (i < 8) - upper |= 0x08; - else - upper |= 0x10; - } else { - *(dosname + i) = *buf; - } - i++; - } - } - - uniname++; - } - - if (*dosname == 0xE5) - *dosname = 0x05; - - if (*uniname != 0x0) - lossy = true; - - if (upper & lower) - p_dosname->name_case = 0xFF; - else - p_dosname->name_case = lower; - - if (p_lossy) - *p_lossy = lossy; -} - -void nls_dosname_to_uniname(struct super_block *sb, - struct uni_name_t *p_uniname, - struct dos_name_t *p_dosname) -{ - int i = 0, j, n = 0; - u8 buf[DOS_NAME_LENGTH + 2]; - u8 *dosname = p_dosname->name; - u16 *uniname = p_uniname->name; - struct nls_table *nls = EXFAT_SB(sb)->nls_disk; - - if (*dosname == 0x05) { - *buf = 0xE5; - i++; - n++; - } - - for (; i < 8; i++, n++) { - if (*(dosname + i) == ' ') - break; - - if ((*(dosname + i) >= 'A') && (*(dosname + i) <= 'Z') && - (p_dosname->name_case & 0x08)) - *(buf + n) = *(dosname + i) + ('a' - 'A'); - else - *(buf + n) = *(dosname + i); - } - if (*(dosname + 8) != ' ') { - *(buf + n) = '.'; - n++; - } - - for (i = 8; i < DOS_NAME_LENGTH; i++, n++) { - if (*(dosname + i) == ' ') - break; - - if ((*(dosname + i) >= 'A') && (*(dosname + i) <= 'Z') && - (p_dosname->name_case & 0x10)) - *(buf + n) = *(dosname + i) + ('a' - 'A'); - else - *(buf + n) = *(dosname + i); - } - *(buf + n) = '\0'; - - i = 0; - j = 0; - while (j < (MAX_NAME_LENGTH - 1)) { - if (*(buf + i) == '\0') - break; - - i += convert_ch_to_uni(nls, uniname, (buf + i), NULL); - - uniname++; - j++; - } - - *uniname = (u16)'\0'; -} - void nls_uniname_to_cstring(struct super_block *sb, u8 *p_cstring, struct uni_name_t *p_uniname) { diff --git a/drivers/staging/exfat/exfat_super.c b/drivers/staging/exfat/exfat_super.c index 58c7d66..b81d2a8 100644 --- a/drivers/staging/exfat/exfat_super.c +++ b/drivers/staging/exfat/exfat_super.c @@ -26,7 +26,7 @@ #include #include #include - +#include #include #include #include @@ -38,8 +38,8 @@ static struct kmem_cache *exfat_inode_cachep; -static int exfat_default_codepage = CONFIG_EXFAT_DEFAULT_CODEPAGE; -static char exfat_default_iocharset[] = CONFIG_EXFAT_DEFAULT_IOCHARSET; +static int exfat_default_codepage = CONFIG_STAGING_EXFAT_DEFAULT_CODEPAGE; +static char exfat_default_iocharset[] = CONFIG_STAGING_EXFAT_DEFAULT_IOCHARSET; #define INC_IVERSION(x) (inode_inc_iversion(x)) #define GET_IVERSION(x) (inode_peek_iversion_raw(x)) @@ -284,12 +284,12 @@ static const struct dentry_operations exfat_dentry_ops = { .d_compare = exfat_cmp, }; -static DEFINE_SEMAPHORE(z_sem); +static DEFINE_MUTEX(z_mutex); static inline void fs_sync(struct super_block *sb, bool do_sync) { if (do_sync) - bdev_sync(sb); + exfat_bdev_sync(sb); } /* @@ -353,26 +353,28 @@ static int ffsMountVol(struct super_block *sb) pr_info("[EXFAT] trying to mount...\n"); - down(&z_sem); + mutex_lock(&z_mutex); - buf_init(sb); + exfat_buf_init(sb); - sema_init(&p_fs->v_sem, 1); + mutex_init(&p_fs->v_mutex); p_fs->dev_ejected = 0; /* open the block device */ - bdev_open(sb); + exfat_bdev_open(sb); if (p_bd->sector_size < sb->s_blocksize) { - ret = FFS_MEDIAERR; + printk(KERN_INFO "EXFAT: mount failed - sector size %d less than blocksize %ld\n", + p_bd->sector_size, sb->s_blocksize); + ret = -EINVAL; goto out; } if (p_bd->sector_size > sb->s_blocksize) sb_set_blocksize(sb, p_bd->sector_size); /* read Sector 0 */ - if (sector_read(sb, 0, &tmp_bh, 1) != FFS_SUCCESS) { - ret = FFS_MEDIAERR; + if (sector_read(sb, 0, &tmp_bh, 1) != 0) { + ret = -EIO; goto out; } @@ -383,8 +385,8 @@ static int ffsMountVol(struct super_block *sb) /* check the validity of PBR */ if (GET16_A(p_pbr->signature) != PBR_SIGNATURE) { brelse(tmp_bh); - bdev_close(sb); - ret = FFS_FORMATERR; + exfat_bdev_close(sb); + ret = -EFSCORRUPTED; goto out; } @@ -394,16 +396,10 @@ static int ffsMountVol(struct super_block *sb) break; if (i < 53) { -#ifdef CONFIG_EXFAT_DONT_MOUNT_VFAT + /* Not sure how we'd get here, but complain if it does */ ret = -EINVAL; - printk(KERN_INFO "EXFAT: Attempted to mount VFAT filesystem\n"); + pr_info("EXFAT: Attempted to mount VFAT filesystem\n"); goto out; -#else - if (GET16(p_pbr->bpb + 11)) /* num_fat_sectors */ - ret = fat16_mount(sb, p_pbr); - else - ret = fat32_mount(sb, p_pbr); -#endif } else { ret = exfat_mount(sb, p_pbr); } @@ -411,38 +407,34 @@ static int ffsMountVol(struct super_block *sb) brelse(tmp_bh); if (ret) { - bdev_close(sb); + exfat_bdev_close(sb); goto out; } - if (p_fs->vol_type == EXFAT) { - ret = load_alloc_bitmap(sb); - if (ret) { - bdev_close(sb); - goto out; - } - ret = load_upcase_table(sb); - if (ret) { - free_alloc_bitmap(sb); - bdev_close(sb); - goto out; - } + ret = load_alloc_bitmap(sb); + if (ret) { + exfat_bdev_close(sb); + goto out; + } + ret = load_upcase_table(sb); + if (ret) { + free_alloc_bitmap(sb); + exfat_bdev_close(sb); + goto out; } if (p_fs->dev_ejected) { - if (p_fs->vol_type == EXFAT) { - free_upcase_table(sb); - free_alloc_bitmap(sb); - } - bdev_close(sb); - ret = FFS_MEDIAERR; + free_upcase_table(sb); + free_alloc_bitmap(sb); + exfat_bdev_close(sb); + ret = -EIO; goto out; } pr_info("[EXFAT] mounted successfully\n"); out: - up(&z_sem); + mutex_unlock(&z_mutex); return ret; } @@ -450,39 +442,37 @@ out: static int ffsUmountVol(struct super_block *sb) { struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - int err = FFS_SUCCESS; + int err = 0; pr_info("[EXFAT] trying to unmount...\n"); - down(&z_sem); + mutex_lock(&z_mutex); /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); - fs_sync(sb, false); + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); - if (p_fs->vol_type == EXFAT) { - free_upcase_table(sb); - free_alloc_bitmap(sb); - } + free_upcase_table(sb); + free_alloc_bitmap(sb); - FAT_release_all(sb); - buf_release_all(sb); + exfat_fat_release_all(sb); + exfat_buf_release_all(sb); /* close the block device */ - bdev_close(sb); + exfat_bdev_close(sb); if (p_fs->dev_ejected) { pr_info("[EXFAT] unmounted with media errors. Device is already ejected.\n"); - err = FFS_MEDIAERR; + err = -EIO; } - buf_shutdown(sb); + exfat_buf_shutdown(sb); /* release the lock for file system critical section */ - up(&p_fs->v_sem); - up(&z_sem); + mutex_unlock(&p_fs->v_mutex); + mutex_unlock(&z_mutex); pr_info("[EXFAT] unmounted successfully\n"); @@ -491,18 +481,18 @@ static int ffsUmountVol(struct super_block *sb) static int ffsGetVolInfo(struct super_block *sb, struct vol_info_t *info) { - int err = FFS_SUCCESS; + int err = 0; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); /* check the validity of pointer parameters */ if (!info) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); if (p_fs->used_clusters == UINT_MAX) - p_fs->used_clusters = p_fs->fs_func->count_used_clusters(sb); + p_fs->used_clusters = exfat_count_used_clusters(sb); info->FatType = p_fs->vol_type; info->ClusterSize = p_fs->cluster_size; @@ -511,31 +501,31 @@ static int ffsGetVolInfo(struct super_block *sb, struct vol_info_t *info) info->FreeClusters = info->NumClusters - info->UsedClusters; if (p_fs->dev_ejected) - err = FFS_MEDIAERR; + err = -EIO; /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return err; } static int ffsSyncVol(struct super_block *sb, bool do_sync) { - int err = FFS_SUCCESS; + int err = 0; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* synchronize the file system */ fs_sync(sb, do_sync); fs_set_vol_flags(sb, VOL_CLEAN); if (p_fs->dev_ejected) - err = FFS_MEDIAERR; + err = -EIO; /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return err; } @@ -559,10 +549,10 @@ static int ffsLookupFile(struct inode *inode, char *path, struct file_id_t *fid) /* check the validity of pointer parameters */ if (!fid || !path || (*path == '\0')) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check the validity of directory name in the given pathname */ ret = resolve_path(inode, path, &dir, &uni_name); @@ -575,10 +565,10 @@ static int ffsLookupFile(struct inode *inode, char *path, struct file_id_t *fid) goto out; /* search the file name for directories */ - dentry = p_fs->fs_func->find_dir_entry(sb, &dir, &uni_name, num_entries, - &dos_name, TYPE_ALL); + dentry = exfat_find_dir_entry(sb, &dir, &uni_name, num_entries, + &dos_name, TYPE_ALL); if (dentry < -1) { - ret = FFS_NOTFOUND; + ret = -ENOENT; goto out; } @@ -597,46 +587,36 @@ static int ffsLookupFile(struct inode *inode, char *path, struct file_id_t *fid) fid->size = 0; fid->start_clu = p_fs->root_dir; } else { - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &dir, dentry, - ES_2_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep + 1; - } else { - ep = get_entry_in_dir(sb, &dir, dentry, NULL); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep; + es = get_entry_set_in_dir(sb, &dir, dentry, + ES_2_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } + ep2 = ep + 1; - fid->type = p_fs->fs_func->get_entry_type(ep); + fid->type = exfat_get_entry_type(ep); fid->rwoffset = 0; fid->hint_last_off = -1; - fid->attr = p_fs->fs_func->get_entry_attr(ep); + fid->attr = exfat_get_entry_attr(ep); - fid->size = p_fs->fs_func->get_entry_size(ep2); + fid->size = exfat_get_entry_size(ep2); if ((fid->type == TYPE_FILE) && (fid->size == 0)) { fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; fid->start_clu = CLUSTER_32(~0); } else { - fid->flags = p_fs->fs_func->get_entry_flag(ep2); - fid->start_clu = p_fs->fs_func->get_entry_clu0(ep2); + fid->flags = exfat_get_entry_flag(ep2); + fid->start_clu = exfat_get_entry_clu0(ep2); } - if (p_fs->vol_type == EXFAT) - release_entry_set(es); + release_entry_set(es); } if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -648,14 +628,14 @@ static int ffsCreateFile(struct inode *inode, char *path, u8 mode, struct uni_name_t uni_name; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - int ret; + int ret = 0; /* check the validity of pointer parameters */ if (!fid || !path || (*path == '\0')) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check the validity of directory name in the given pathname */ ret = resolve_path(inode, path, &dir, &uni_name); @@ -667,17 +647,17 @@ static int ffsCreateFile(struct inode *inode, char *path, u8 mode, /* create a new file */ ret = create_file(inode, &dir, &uni_name, mode, fid); -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -697,18 +677,18 @@ static int ffsReadFile(struct inode *inode, struct file_id_t *fid, void *buffer, /* check the validity of the given file id */ if (!fid) - return FFS_INVALIDFID; + return -EINVAL; /* check the validity of pointer parameters */ if (!buffer) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check if the given file ID is opened */ if (fid->type != TYPE_FILE) { - ret = FFS_PERMISSIONERR; + ret = -EPERM; goto out; } @@ -721,7 +701,7 @@ static int ffsReadFile(struct inode *inode, struct file_id_t *fid, void *buffer, if (count == 0) { if (rcount) *rcount = 0; - ret = FFS_EOF; + ret = 0; goto out; } @@ -742,9 +722,11 @@ static int ffsReadFile(struct inode *inode, struct file_id_t *fid, void *buffer, } while (clu_offset > 0) { - /* clu = FAT_read(sb, clu); */ - if (FAT_read(sb, clu, &clu) == -1) - return FFS_MEDIAERR; + /* clu = exfat_fat_read(sb, clu); */ + if (exfat_fat_read(sb, clu, &clu) == -1) { + ret = -EIO; + goto out; + } clu_offset--; } @@ -772,13 +754,13 @@ static int ffsReadFile(struct inode *inode, struct file_id_t *fid, void *buffer, if ((offset == 0) && (oneblkread == p_bd->sector_size)) { if (sector_read(sb, LogSector, &tmp_bh, 1) != - FFS_SUCCESS) + 0) goto err_out; memcpy((char *)buffer + read_bytes, (char *)tmp_bh->b_data, (s32)oneblkread); } else { if (sector_read(sb, LogSector, &tmp_bh, 1) != - FFS_SUCCESS) + 0) goto err_out; memcpy((char *)buffer + read_bytes, (char *)tmp_bh->b_data + offset, @@ -797,11 +779,11 @@ err_out: *rcount = read_bytes; if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -814,7 +796,7 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, s32 num_clusters, num_alloc, num_alloced = (s32)~0; int ret = 0; u32 clu, last_clu; - sector_t LogSector, sector = 0; + sector_t LogSector; u64 oneblkwrite, write_bytes; struct chain_t new_clu; struct timestamp_t tm; @@ -827,18 +809,18 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, /* check the validity of the given file id */ if (!fid) - return FFS_INVALIDFID; + return -EINVAL; /* check the validity of pointer parameters */ if (!buffer) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check if the given file ID is opened */ if (fid->type != TYPE_FILE) { - ret = FFS_PERMISSIONERR; + ret = -EPERM; goto out; } @@ -848,7 +830,7 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, if (count == 0) { if (wcount) *wcount = 0; - ret = FFS_SUCCESS; + ret = 0; goto out; } @@ -864,7 +846,8 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, while (count > 0) { clu_offset = (s32)(fid->rwoffset >> p_fs->cluster_size_bits); - clu = last_clu = fid->start_clu; + clu = fid->start_clu; + last_clu = fid->start_clu; if (fid->flags == 0x03) { if ((clu_offset > 0) && (clu != CLUSTER_32(~0))) { @@ -885,9 +868,9 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, while ((clu_offset > 0) && (clu != CLUSTER_32(~0))) { last_clu = clu; - /* clu = FAT_read(sb, clu); */ - if (FAT_read(sb, clu, &clu) == -1) { - ret = FFS_MEDIAERR; + /* clu = exfat_fat_read(sb, clu); */ + if (exfat_fat_read(sb, clu, &clu) == -1) { + ret = -EIO; goto out; } clu_offset--; @@ -903,13 +886,13 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, new_clu.flags = fid->flags; /* (1) allocate a chain of clusters */ - num_alloced = p_fs->fs_func->alloc_cluster(sb, - num_alloc, - &new_clu); + num_alloced = exfat_alloc_cluster(sb, + num_alloc, + &new_clu); if (num_alloced == 0) break; if (num_alloced < 0) { - ret = FFS_MEDIAERR; + ret = num_alloced; goto out; } @@ -928,7 +911,7 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, modified = true; } if (new_clu.flags == 0x01) - FAT_write(sb, last_clu, new_clu.dir); + exfat_fat_write(sb, last_clu, new_clu.dir); } num_clusters += num_alloced; @@ -957,12 +940,12 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, if ((offset == 0) && (oneblkwrite == p_bd->sector_size)) { if (sector_read(sb, LogSector, &tmp_bh, 0) != - FFS_SUCCESS) + 0) goto err_out; memcpy((char *)tmp_bh->b_data, (char *)buffer + write_bytes, (s32)oneblkwrite); if (sector_write(sb, LogSector, tmp_bh, 0) != - FFS_SUCCESS) { + 0) { brelse(tmp_bh); goto err_out; } @@ -970,18 +953,18 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, if ((offset > 0) || ((fid->rwoffset + oneblkwrite) < fid->size)) { if (sector_read(sb, LogSector, &tmp_bh, 1) != - FFS_SUCCESS) + 0) goto err_out; } else { if (sector_read(sb, LogSector, &tmp_bh, 0) != - FFS_SUCCESS) + 0) goto err_out; } memcpy((char *)tmp_bh->b_data + offset, (char *)buffer + write_bytes, (s32)oneblkwrite); if (sector_write(sb, LogSector, tmp_bh, 0) != - FFS_SUCCESS) { + 0) { brelse(tmp_bh); goto err_out; } @@ -1002,46 +985,31 @@ static int ffsWriteFile(struct inode *inode, struct file_id_t *fid, brelse(tmp_bh); /* (3) update the direcoty entry */ - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &(fid->dir), fid->entry, - ES_ALL_ENTRIES, &ep); - if (!es) - goto err_out; - ep2 = ep + 1; - } else { - ep = get_entry_in_dir(sb, &(fid->dir), fid->entry, §or); - if (!ep) - goto err_out; - ep2 = ep; - } - - p_fs->fs_func->set_entry_time(ep, tm_current(&tm), TM_MODIFY); - p_fs->fs_func->set_entry_attr(ep, fid->attr); + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_ALL_ENTRIES, &ep); + if (!es) + goto err_out; + ep2 = ep + 1; - if (p_fs->vol_type != EXFAT) - buf_modify(sb, sector); + exfat_set_entry_time(ep, tm_current(&tm), TM_MODIFY); + exfat_set_entry_attr(ep, fid->attr); if (modified) { - if (p_fs->fs_func->get_entry_flag(ep2) != fid->flags) - p_fs->fs_func->set_entry_flag(ep2, fid->flags); - - if (p_fs->fs_func->get_entry_size(ep2) != fid->size) - p_fs->fs_func->set_entry_size(ep2, fid->size); + if (exfat_get_entry_flag(ep2) != fid->flags) + exfat_set_entry_flag(ep2, fid->flags); - if (p_fs->fs_func->get_entry_clu0(ep2) != fid->start_clu) - p_fs->fs_func->set_entry_clu0(ep2, fid->start_clu); + if (exfat_get_entry_size(ep2) != fid->size) + exfat_set_entry_size(ep2, fid->size); - if (p_fs->vol_type != EXFAT) - buf_modify(sb, sector); + if (exfat_get_entry_clu0(ep2) != fid->start_clu) + exfat_set_entry_clu0(ep2, fid->start_clu); } - if (p_fs->vol_type == EXFAT) { - update_dir_checksum_with_entry_set(sb, es); - release_entry_set(es); - } + update_dir_checksum_with_entry_set(sb, es); + release_entry_set(es); -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif @@ -1051,14 +1019,14 @@ err_out: *wcount = write_bytes; if (num_alloced == 0) - ret = FFS_FULL; + ret = -ENOSPC; else if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1068,7 +1036,6 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) s32 num_clusters; u32 last_clu = CLUSTER_32(0); int ret = 0; - sector_t sector = 0; struct chain_t clu; struct timestamp_t tm; struct dentry_t *ep, *ep2; @@ -1081,11 +1048,11 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) new_size); /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check if the given file ID is opened */ if (fid->type != TYPE_FILE) { - ret = FFS_PERMISSIONERR; + ret = -EPERM; goto out; } @@ -1095,7 +1062,7 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) } if (old_size <= new_size) { - ret = FFS_SUCCESS; + ret = 0; goto out; } @@ -1114,8 +1081,8 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) } else { while (num_clusters > 0) { last_clu = clu.dir; - if (FAT_read(sb, clu.dir, &clu.dir) == -1) { - ret = FFS_MEDIAERR; + if (exfat_fat_read(sb, clu.dir, &clu.dir) == -1) { + ret = -EIO; goto out; } num_clusters--; @@ -1133,65 +1100,52 @@ static int ffsTruncateFile(struct inode *inode, u64 old_size, u64 new_size) } /* (1) update the directory entry */ - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, - ES_ALL_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep + 1; - } else { - ep = get_entry_in_dir(sb, &(fid->dir), fid->entry, §or); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_ALL_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } - ep2 = ep; - } + ep2 = ep + 1; - p_fs->fs_func->set_entry_time(ep, tm_current(&tm), TM_MODIFY); - p_fs->fs_func->set_entry_attr(ep, fid->attr); + exfat_set_entry_time(ep, tm_current(&tm), TM_MODIFY); + exfat_set_entry_attr(ep, fid->attr); - p_fs->fs_func->set_entry_size(ep2, new_size); + exfat_set_entry_size(ep2, new_size); if (new_size == 0) { - p_fs->fs_func->set_entry_flag(ep2, 0x01); - p_fs->fs_func->set_entry_clu0(ep2, CLUSTER_32(0)); + exfat_set_entry_flag(ep2, 0x01); + exfat_set_entry_clu0(ep2, CLUSTER_32(0)); } - if (p_fs->vol_type != EXFAT) { - buf_modify(sb, sector); - } else { - update_dir_checksum_with_entry_set(sb, es); - release_entry_set(es); - } + update_dir_checksum_with_entry_set(sb, es); + release_entry_set(es); /* (2) cut off from the FAT chain */ if (last_clu != CLUSTER_32(0)) { if (fid->flags == 0x01) - FAT_write(sb, last_clu, CLUSTER_32(~0)); + exfat_fat_write(sb, last_clu, CLUSTER_32(~0)); } /* (3) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu, 0); + exfat_free_cluster(sb, &clu, 0); /* hint information */ fid->hint_last_off = -1; if (fid->rwoffset > fid->size) fid->rwoffset = fid->size; -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: pr_debug("%s exited (%d)\n", __func__, ret); /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1232,14 +1186,14 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, /* check the validity of the given file id */ if (!fid) - return FFS_INVALIDFID; + return -EINVAL; /* check the validity of pointer parameters */ if (!new_path || (*new_path == '\0')) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); update_parent_info(fid, old_parent_inode); @@ -1252,19 +1206,19 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, /* check if the old file is "." or ".." */ if (p_fs->vol_type != EXFAT) { if ((olddir.dir != p_fs->root_dir) && (dentry < 2)) { - ret = FFS_PERMISSIONERR; + ret = -EPERM; goto out2; } } ep = get_entry_in_dir(sb, &olddir, dentry, NULL); if (!ep) { - ret = FFS_MEDIAERR; + ret = -ENOENT; goto out2; } - if (p_fs->fs_func->get_entry_attr(ep) & ATTR_READONLY) { - ret = FFS_PERMISSIONERR; + if (exfat_get_entry_attr(ep) & ATTR_READONLY) { + ret = -EPERM; goto out2; } @@ -1272,18 +1226,18 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, if (new_inode) { u32 entry_type; - ret = FFS_MEDIAERR; + ret = -ENOENT; new_fid = &EXFAT_I(new_inode)->fid; update_parent_info(new_fid, new_parent_inode); - p_dir = &(new_fid->dir); + p_dir = &new_fid->dir; new_entry = new_fid->entry; ep = get_entry_in_dir(sb, p_dir, new_entry, NULL); if (!ep) goto out; - entry_type = p_fs->fs_func->get_entry_type(ep); + entry_type = exfat_get_entry_type(ep); if (entry_type == TYPE_DIR) { struct chain_t new_clu; @@ -1294,7 +1248,7 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, new_clu.flags = new_fid->flags; if (!is_dir_empty(sb, &new_clu)) { - ret = FFS_FILEEXIST; + ret = -EEXIST; goto out; } } @@ -1314,30 +1268,30 @@ static int ffsMoveFile(struct inode *old_parent_inode, struct file_id_t *fid, ret = move_file(new_parent_inode, &olddir, dentry, &newdir, &uni_name, fid); - if ((ret == FFS_SUCCESS) && new_inode) { + if ((ret == 0) && new_inode) { /* delete entries of new_dir */ ep = get_entry_in_dir(sb, p_dir, new_entry, NULL); if (!ep) goto out; - num_entries = p_fs->fs_func->count_ext_entries(sb, p_dir, - new_entry, ep); + num_entries = exfat_count_ext_entries(sb, p_dir, + new_entry, ep); if (num_entries < 0) goto out; - p_fs->fs_func->delete_dir_entry(sb, p_dir, new_entry, 0, - num_entries + 1); + exfat_delete_dir_entry(sb, p_dir, new_entry, 0, + num_entries + 1); } out: -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out2: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1345,7 +1299,7 @@ out2: static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) { s32 dentry; - int ret = FFS_SUCCESS; + int ret = 0; struct chain_t dir, clu_to_free; struct dentry_t *ep; struct super_block *sb = inode->i_sb; @@ -1353,10 +1307,10 @@ static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) /* check the validity of the given file id */ if (!fid) - return FFS_INVALIDFID; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); dir.dir = fid->dir.dir; dir.size = fid->dir.size; @@ -1366,12 +1320,12 @@ static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) ep = get_entry_in_dir(sb, &dir, dentry, NULL); if (!ep) { - ret = FFS_MEDIAERR; + ret = -ENOENT; goto out; } - if (p_fs->fs_func->get_entry_attr(ep) & ATTR_READONLY) { - ret = FFS_PERMISSIONERR; + if (exfat_get_entry_attr(ep) & ATTR_READONLY) { + ret = -EPERM; goto out; } fs_set_vol_flags(sb, VOL_DIRTY); @@ -1384,22 +1338,22 @@ static int ffsRemoveFile(struct inode *inode, struct file_id_t *fid) clu_to_free.flags = fid->flags; /* (2) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu_to_free, 0); + exfat_free_cluster(sb, &clu_to_free, 0); fid->size = 0; fid->start_clu = CLUSTER_32(~0); fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1409,7 +1363,7 @@ out: static int ffsSetAttr(struct inode *inode, u32 attr) { u32 type; - int ret = FFS_SUCCESS; + int ret = 0; sector_t sector = 0; struct dentry_t *ep; struct super_block *sb = inode->i_sb; @@ -1420,49 +1374,40 @@ static int ffsSetAttr(struct inode *inode, u32 attr) if (fid->attr == attr) { if (p_fs->dev_ejected) - return FFS_MEDIAERR; - return FFS_SUCCESS; + return -EIO; + return 0; } if (is_dir) { if ((fid->dir.dir == p_fs->root_dir) && (fid->entry == -1)) { if (p_fs->dev_ejected) - return FFS_MEDIAERR; - return FFS_SUCCESS; + return -EIO; + return 0; } } /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* get the directory entry of given file */ - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &(fid->dir), fid->entry, - ES_ALL_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - } else { - ep = get_entry_in_dir(sb, &(fid->dir), fid->entry, §or); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_ALL_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } - type = p_fs->fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (((type == TYPE_FILE) && (attr & ATTR_SUBDIR)) || ((type == TYPE_DIR) && (!(attr & ATTR_SUBDIR)))) { if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; else - ret = FFS_ERROR; + ret = -EINVAL; - if (p_fs->vol_type == EXFAT) - release_entry_set(es); + release_entry_set(es); goto out; } @@ -1470,25 +1415,21 @@ static int ffsSetAttr(struct inode *inode, u32 attr) /* set the file attribute */ fid->attr = attr; - p_fs->fs_func->set_entry_attr(ep, attr); + exfat_set_entry_attr(ep, attr); - if (p_fs->vol_type != EXFAT) { - buf_modify(sb, sector); - } else { - update_dir_checksum_with_entry_set(sb, es); - release_entry_set(es); - } + update_dir_checksum_with_entry_set(sb, es); + release_entry_set(es); -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1496,9 +1437,8 @@ out: static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) { - sector_t sector = 0; s32 count; - int ret = FFS_SUCCESS; + int ret = 0; struct chain_t dir; struct uni_name_t uni_name; struct timestamp_t tm; @@ -1512,7 +1452,7 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) pr_debug("%s entered\n", __func__); /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); if (is_dir) { if ((fid->dir.dir == p_fs->root_dir) && @@ -1541,40 +1481,30 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) count = count_dos_name_entries(sb, &dir, TYPE_DIR); if (count < 0) { - ret = FFS_MEDIAERR; + ret = count; /* propagate error upward */ goto out; } info->NumSubdirs = count; if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; goto out; } } /* get the directory entry of given file or directory */ - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &(fid->dir), fid->entry, - ES_2_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep + 1; - } else { - ep = get_entry_in_dir(sb, &(fid->dir), fid->entry, §or); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep; - buf_lock(sb, sector); + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_2_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } + ep2 = ep + 1; /* set FILE_INFO structure using the acquired struct dentry_t */ - info->Attr = p_fs->fs_func->get_entry_attr(ep); + info->Attr = exfat_get_entry_attr(ep); - p_fs->fs_func->get_entry_time(ep, &tm, TM_CREATE); + exfat_get_entry_time(ep, &tm, TM_CREATE); info->CreateTimestamp.Year = tm.year; info->CreateTimestamp.Month = tm.mon; info->CreateTimestamp.Day = tm.day; @@ -1583,7 +1513,7 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) info->CreateTimestamp.Second = tm.sec; info->CreateTimestamp.MilliSecond = 0; - p_fs->fs_func->get_entry_time(ep, &tm, TM_MODIFY); + exfat_get_entry_time(ep, &tm, TM_MODIFY); info->ModifyTimestamp.Year = tm.year; info->ModifyTimestamp.Month = tm.mon; info->ModifyTimestamp.Day = tm.day; @@ -1594,31 +1524,19 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) memset((char *)&info->AccessTimestamp, 0, sizeof(struct date_time_t)); - *(uni_name.name) = 0x0; + *uni_name.name = 0x0; /* XXX this is very bad for exfat cuz name is already included in es. * API should be revised */ - p_fs->fs_func->get_uni_name_from_ext_entry(sb, &(fid->dir), fid->entry, - uni_name.name); - if (*uni_name.name == 0x0 && p_fs->vol_type != EXFAT) - get_uni_name_from_dos_entry(sb, (struct dos_dentry_t *)ep, - &uni_name, 0x1); + exfat_get_uni_name_from_ext_entry(sb, &fid->dir, fid->entry, + uni_name.name); nls_uniname_to_cstring(sb, info->Name, &uni_name); - if (p_fs->vol_type == EXFAT) { - info->NumSubdirs = 2; - } else { - buf_unlock(sb, sector); - get_uni_name_from_dos_entry(sb, (struct dos_dentry_t *)ep, - &uni_name, 0x0); - nls_uniname_to_cstring(sb, info->ShortName, &uni_name); - info->NumSubdirs = 0; - } + info->NumSubdirs = 2; - info->Size = p_fs->fs_func->get_entry_size(ep2); + info->Size = exfat_get_entry_size(ep2); - if (p_fs->vol_type == EXFAT) - release_entry_set(es); + release_entry_set(es); if (is_dir) { dir.dir = fid->start_clu; @@ -1630,18 +1548,18 @@ static int ffsReadStat(struct inode *inode, struct dir_entry_t *info) count = count_dos_name_entries(sb, &dir, TYPE_DIR); if (count < 0) { - ret = FFS_MEDIAERR; + ret = count; /* propagate error upward */ goto out; } info->NumSubdirs += count; } if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); pr_debug("%s exited successfully\n", __func__); return ret; @@ -1649,8 +1567,7 @@ out: static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) { - sector_t sector = 0; - int ret = FFS_SUCCESS; + int ret = 0; struct timestamp_t tm; struct dentry_t *ep, *ep2; struct entry_set_cache_t *es = NULL; @@ -1662,14 +1579,14 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) pr_debug("%s entered (inode %p info %p\n", __func__, inode, info); /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); if (is_dir) { if ((fid->dir.dir == p_fs->root_dir) && (fid->entry == -1)) { if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; - ret = FFS_SUCCESS; + ret = -EIO; + ret = 0; goto out; } } @@ -1677,25 +1594,15 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) fs_set_vol_flags(sb, VOL_DIRTY); /* get the directory entry of given file or directory */ - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &(fid->dir), fid->entry, - ES_ALL_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep + 1; - } else { - /* for other than exfat */ - ep = get_entry_in_dir(sb, &(fid->dir), fid->entry, §or); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } - ep2 = ep; + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_ALL_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } + ep2 = ep + 1; - p_fs->fs_func->set_entry_attr(ep, info->Attr); + exfat_set_entry_attr(ep, info->Attr); /* set FILE_INFO structure using the acquired struct dentry_t */ tm.sec = info->CreateTimestamp.Second; @@ -1704,7 +1611,7 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) tm.day = info->CreateTimestamp.Day; tm.mon = info->CreateTimestamp.Month; tm.year = info->CreateTimestamp.Year; - p_fs->fs_func->set_entry_time(ep, &tm, TM_CREATE); + exfat_set_entry_time(ep, &tm, TM_CREATE); tm.sec = info->ModifyTimestamp.Second; tm.min = info->ModifyTimestamp.Minute; @@ -1712,23 +1619,19 @@ static int ffsWriteStat(struct inode *inode, struct dir_entry_t *info) tm.day = info->ModifyTimestamp.Day; tm.mon = info->ModifyTimestamp.Month; tm.year = info->ModifyTimestamp.Year; - p_fs->fs_func->set_entry_time(ep, &tm, TM_MODIFY); + exfat_set_entry_time(ep, &tm, TM_MODIFY); - p_fs->fs_func->set_entry_size(ep2, info->Size); + exfat_set_entry_size(ep2, info->Size); - if (p_fs->vol_type != EXFAT) { - buf_modify(sb, sector); - } else { - update_dir_checksum_with_entry_set(sb, es); - release_entry_set(es); - } + update_dir_checksum_with_entry_set(sb, es); + release_entry_set(es); if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); pr_debug("%s exited (%d)\n", __func__, ret); @@ -1740,8 +1643,7 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) s32 num_clusters, num_alloced; bool modified = false; u32 last_clu; - int ret = FFS_SUCCESS; - sector_t sector = 0; + int ret = 0; struct chain_t new_clu; struct dentry_t *ep; struct entry_set_cache_t *es = NULL; @@ -1751,10 +1653,10 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) /* check the validity of pointer parameters */ if (!clu) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); fid->rwoffset = (s64)(clu_offset) << p_fs->cluster_size_bits; @@ -1785,8 +1687,8 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) while ((clu_offset > 0) && (*clu != CLUSTER_32(~0))) { last_clu = *clu; - if (FAT_read(sb, *clu, clu) == -1) { - ret = FFS_MEDIAERR; + if (exfat_fat_read(sb, *clu, clu) == -1) { + ret = -EIO; goto out; } clu_offset--; @@ -1802,12 +1704,12 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) new_clu.flags = fid->flags; /* (1) allocate a cluster */ - num_alloced = p_fs->fs_func->alloc_cluster(sb, 1, &new_clu); + num_alloced = exfat_alloc_cluster(sb, 1, &new_clu); if (num_alloced < 0) { - ret = FFS_MEDIAERR; + ret = -EIO; goto out; } else if (num_alloced == 0) { - ret = FFS_FULL; + ret = -ENOSPC; goto out; } @@ -1825,49 +1727,32 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) modified = true; } if (new_clu.flags == 0x01) - FAT_write(sb, last_clu, new_clu.dir); + exfat_fat_write(sb, last_clu, new_clu.dir); } num_clusters += num_alloced; *clu = new_clu.dir; - if (p_fs->vol_type == EXFAT) { - es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, - ES_ALL_ENTRIES, &ep); - if (!es) { - ret = FFS_MEDIAERR; - goto out; - } - /* get stream entry */ - ep++; + es = get_entry_set_in_dir(sb, &fid->dir, fid->entry, + ES_ALL_ENTRIES, &ep); + if (!es) { + ret = -ENOENT; + goto out; } + /* get stream entry */ + ep++; /* (3) update directory entry */ if (modified) { - if (p_fs->vol_type != EXFAT) { - ep = get_entry_in_dir(sb, &(fid->dir), - fid->entry, §or); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } - } + if (exfat_get_entry_flag(ep) != fid->flags) + exfat_set_entry_flag(ep, fid->flags); - if (p_fs->fs_func->get_entry_flag(ep) != fid->flags) - p_fs->fs_func->set_entry_flag(ep, fid->flags); - - if (p_fs->fs_func->get_entry_clu0(ep) != fid->start_clu) - p_fs->fs_func->set_entry_clu0(ep, - fid->start_clu); - - if (p_fs->vol_type != EXFAT) - buf_modify(sb, sector); + if (exfat_get_entry_clu0(ep) != fid->start_clu) + exfat_set_entry_clu0(ep, fid->start_clu); } - if (p_fs->vol_type == EXFAT) { - update_dir_checksum_with_entry_set(sb, es); - release_entry_set(es); - } + update_dir_checksum_with_entry_set(sb, es); + release_entry_set(es); /* add number of new blocks to inode */ inode->i_blocks += num_alloced << (p_fs->cluster_size_bits - 9); @@ -1878,11 +1763,11 @@ static int ffsMapCluster(struct inode *inode, s32 clu_offset, u32 *clu) fid->hint_last_clu = *clu; if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1893,7 +1778,7 @@ out: static int ffsCreateDir(struct inode *inode, char *path, struct file_id_t *fid) { - int ret = FFS_SUCCESS; + int ret = 0; struct chain_t dir; struct uni_name_t uni_name; struct super_block *sb = inode->i_sb; @@ -1903,10 +1788,10 @@ static int ffsCreateDir(struct inode *inode, char *path, struct file_id_t *fid) /* check the validity of pointer parameters */ if (!fid || !path || (*path == '\0')) - return FFS_ERROR; + return -EINVAL; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); /* check the validity of directory name in the given old pathname */ ret = resolve_path(inode, path, &dir, &uni_name); @@ -1917,16 +1802,16 @@ static int ffsCreateDir(struct inode *inode, char *path, struct file_id_t *fid) ret = create_dir(inode, &dir, &uni_name, fid); -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -1934,7 +1819,7 @@ out: static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) { int i, dentry, clu_offset; - int ret = FFS_SUCCESS; + int ret = 0; s32 dentries_per_clu, dentries_per_clu_bits = 0; u32 type; sector_t sector; @@ -1944,19 +1829,18 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) struct dentry_t *ep; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); - struct fs_func *fs_func = p_fs->fs_func; struct file_id_t *fid = &(EXFAT_I(inode)->fid); /* check the validity of pointer parameters */ if (!dir_entry) - return FFS_ERROR; + return -EINVAL; /* check if the given file ID is opened */ if (fid->type != TYPE_DIR) - return FFS_PERMISSIONERR; + return -ENOTDIR; /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); if (fid->entry == -1) { dir.dir = p_fs->root_dir; @@ -2001,9 +1885,9 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) } while (clu_offset > 0) { - /* clu.dir = FAT_read(sb, clu.dir); */ - if (FAT_read(sb, clu.dir, &clu.dir) == -1) { - ret = FFS_MEDIAERR; + /* clu.dir = exfat_fat_read(sb, clu.dir); */ + if (exfat_fat_read(sb, clu.dir, &clu.dir) == -1) { + ret = -EIO; goto out; } clu_offset--; @@ -2023,10 +1907,10 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) for ( ; i < dentries_per_clu; i++, dentry++) { ep = get_entry_in_dir(sb, &clu, i, §or); if (!ep) { - ret = FFS_MEDIAERR; + ret = -ENOENT; goto out; } - type = fs_func->get_entry_type(ep); + type = exfat_get_entry_type(ep); if (type == TYPE_UNUSED) break; @@ -2034,10 +1918,10 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) if ((type != TYPE_FILE) && (type != TYPE_DIR)) continue; - buf_lock(sb, sector); - dir_entry->Attr = fs_func->get_entry_attr(ep); + exfat_buf_lock(sb, sector); + dir_entry->Attr = exfat_get_entry_attr(ep); - fs_func->get_entry_time(ep, &tm, TM_CREATE); + exfat_get_entry_time(ep, &tm, TM_CREATE); dir_entry->CreateTimestamp.Year = tm.year; dir_entry->CreateTimestamp.Month = tm.mon; dir_entry->CreateTimestamp.Day = tm.day; @@ -2046,7 +1930,7 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) dir_entry->CreateTimestamp.Second = tm.sec; dir_entry->CreateTimestamp.MilliSecond = 0; - fs_func->get_entry_time(ep, &tm, TM_MODIFY); + exfat_get_entry_time(ep, &tm, TM_MODIFY); dir_entry->ModifyTimestamp.Year = tm.year; dir_entry->ModifyTimestamp.Month = tm.mon; dir_entry->ModifyTimestamp.Day = tm.day; @@ -2058,31 +1942,19 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) memset((char *)&dir_entry->AccessTimestamp, 0, sizeof(struct date_time_t)); - *(uni_name.name) = 0x0; - fs_func->get_uni_name_from_ext_entry(sb, &dir, dentry, - uni_name.name); - if (*uni_name.name == 0x0 && p_fs->vol_type != EXFAT) - get_uni_name_from_dos_entry(sb, - (struct dos_dentry_t *)ep, - &uni_name, 0x1); + *uni_name.name = 0x0; + exfat_get_uni_name_from_ext_entry(sb, &dir, dentry, + uni_name.name); nls_uniname_to_cstring(sb, dir_entry->Name, &uni_name); - buf_unlock(sb, sector); + exfat_buf_unlock(sb, sector); - if (p_fs->vol_type == EXFAT) { - ep = get_entry_in_dir(sb, &clu, i + 1, NULL); - if (!ep) { - ret = FFS_MEDIAERR; - goto out; - } - } else { - get_uni_name_from_dos_entry(sb, - (struct dos_dentry_t *)ep, - &uni_name, 0x0); - nls_uniname_to_cstring(sb, dir_entry->ShortName, - &uni_name); + ep = get_entry_in_dir(sb, &clu, i + 1, NULL); + if (!ep) { + ret = -ENOENT; + goto out; } - dir_entry->Size = fs_func->get_entry_size(ep); + dir_entry->Size = exfat_get_entry_size(ep); /* hint information */ if (dir.dir == CLUSTER_32(0)) { /* FAT16 root_dir */ @@ -2095,7 +1967,7 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) fid->rwoffset = (s64)(++dentry); if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; goto out; } @@ -2108,24 +1980,24 @@ static int ffsReadDir(struct inode *inode, struct dir_entry_t *dir_entry) else clu.dir = CLUSTER_32(~0); } else { - /* clu.dir = FAT_read(sb, clu.dir); */ - if (FAT_read(sb, clu.dir, &clu.dir) == -1) { - ret = FFS_MEDIAERR; + /* clu.dir = exfat_fat_read(sb, clu.dir); */ + if (exfat_fat_read(sb, clu.dir, &clu.dir) == -1) { + ret = -EIO; goto out; } } } - *(dir_entry->Name) = '\0'; + *dir_entry->Name = '\0'; fid->rwoffset = (s64)(++dentry); if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -2133,14 +2005,14 @@ out: static int ffsRemoveDir(struct inode *inode, struct file_id_t *fid) { s32 dentry; - int ret = FFS_SUCCESS; + int ret = 0; struct chain_t dir, clu_to_free; struct super_block *sb = inode->i_sb; struct fs_info_t *p_fs = &(EXFAT_SB(sb)->fs_info); /* check the validity of the given file id */ if (!fid) - return FFS_INVALIDFID; + return -EINVAL; dir.dir = fid->dir.dir; dir.size = fid->dir.size; @@ -2151,18 +2023,18 @@ static int ffsRemoveDir(struct inode *inode, struct file_id_t *fid) /* check if the file is "." or ".." */ if (p_fs->vol_type != EXFAT) { if ((dir.dir != p_fs->root_dir) && (dentry < 2)) - return FFS_PERMISSIONERR; + return -EPERM; } /* acquire the lock for file system critical section */ - down(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); clu_to_free.dir = fid->start_clu; clu_to_free.size = (s32)((fid->size - 1) >> p_fs->cluster_size_bits) + 1; clu_to_free.flags = fid->flags; if (!is_dir_empty(sb, &clu_to_free)) { - ret = FFS_FILEEXIST; + ret = -ENOTEMPTY; goto out; } @@ -2172,23 +2044,23 @@ static int ffsRemoveDir(struct inode *inode, struct file_id_t *fid) remove_file(inode, &dir, dentry); /* (2) free the clusters */ - p_fs->fs_func->free_cluster(sb, &clu_to_free, 1); + exfat_free_cluster(sb, &clu_to_free, 1); fid->size = 0; fid->start_clu = CLUSTER_32(~0); fid->flags = (p_fs->vol_type == EXFAT) ? 0x03 : 0x01; -#ifdef CONFIG_EXFAT_DELAYED_SYNC - fs_sync(sb, false); +#ifndef CONFIG_STAGING_EXFAT_DELAYED_SYNC + fs_sync(sb, true); fs_set_vol_flags(sb, VOL_CLEAN); #endif if (p_fs->dev_ejected) - ret = FFS_MEDIAERR; + ret = -EIO; out: /* release the lock for file system critical section */ - up(&p_fs->v_sem); + mutex_unlock(&p_fs->v_mutex); return ret; } @@ -2202,7 +2074,7 @@ static int exfat_readdir(struct file *filp, struct dir_context *ctx) struct inode *inode = file_inode(filp); struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct fs_info_t *p_fs = &(sbi->fs_info); + struct fs_info_t *p_fs = &sbi->fs_info; struct bd_info_t *p_bd = &(EXFAT_SB(sb)->bd_info); struct dir_entry_t de; unsigned long inum; @@ -2244,12 +2116,11 @@ get_new: /* at least we tried to read a sector * move cpos to next sector position (should be aligned) */ - if (err == FFS_MEDIAERR) { + if (err == -EIO) { cpos += 1 << p_bd->sector_size_bits; cpos &= ~((1 << p_bd->sector_size_bits) - 1); } - err = -EIO; goto end_of_dir; } @@ -2293,7 +2164,7 @@ static int exfat_ioctl_volume_id(struct inode *dir) { struct super_block *sb = dir->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct fs_info_t *p_fs = &(sbi->fs_info); + struct fs_info_t *p_fs = &sbi->fs_info; return p_fs->vol_id; } @@ -2301,15 +2172,15 @@ static int exfat_ioctl_volume_id(struct inode *dir) static long exfat_generic_ioctl(struct file *filp, unsigned int cmd, unsigned long arg) { -struct inode *inode = filp->f_path.dentry->d_inode; -#ifdef CONFIG_EXFAT_KERNEL_DEBUG + struct inode *inode = filp->f_path.dentry->d_inode; +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG unsigned int flags; -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ switch (cmd) { case EXFAT_IOCTL_GET_VOLUME_ID: return exfat_ioctl_volume_id(inode); -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG case EXFAT_IOC_GET_DEBUGFLAGS: { struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); @@ -2333,7 +2204,7 @@ struct inode *inode = filp->f_path.dentry->d_inode; return 0; } -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ default: return -ENOTTY; /* Inappropriate ioctl for device */ } @@ -2351,6 +2222,7 @@ static int exfat_create(struct inode *dir, struct dentry *dentry, umode_t mode, bool excl) { struct super_block *sb = dir->i_sb; + struct timespec64 curtime; struct inode *inode; struct file_id_t fid; loff_t i_pos; @@ -2361,21 +2233,14 @@ static int exfat_create(struct inode *dir, struct dentry *dentry, umode_t mode, pr_debug("%s entered\n", __func__); err = ffsCreateFile(dir, (u8 *)dentry->d_name.name, FM_REGULAR, &fid); - if (err) { - if (err == FFS_INVALIDPATH) - err = -EINVAL; - else if (err == FFS_FILEEXIST) - err = -EEXIST; - else if (err == FFS_FULL) - err = -ENOSPC; - else if (err == FFS_NAMETOOLONG) - err = -ENAMETOOLONG; - else - err = -EIO; + if (err) goto out; - } + INC_IVERSION(dir); - dir->i_ctime = dir->i_mtime = dir->i_atime = current_time(dir); + curtime = current_time(dir); + dir->i_ctime = curtime; + dir->i_mtime = curtime; + dir->i_atime = curtime; if (IS_DIRSYNC(dir)) (void)exfat_sync_inode(dir); else @@ -2389,7 +2254,10 @@ static int exfat_create(struct inode *dir, struct dentry *dentry, umode_t mode, goto out; } INC_IVERSION(inode); - inode->i_mtime = inode->i_atime = inode->i_ctime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; + inode->i_ctime = curtime; /* * timestamp is already written, so mark_inode_dirty() is unnecessary. */ @@ -2522,6 +2390,7 @@ static int exfat_unlink(struct inode *dir, struct dentry *dentry) { struct inode *inode = dentry->d_inode; struct super_block *sb = dir->i_sb; + struct timespec64 curtime; int err; __lock_super(sb); @@ -2531,22 +2400,22 @@ static int exfat_unlink(struct inode *dir, struct dentry *dentry) EXFAT_I(inode)->fid.size = i_size_read(inode); err = ffsRemoveFile(dir, &(EXFAT_I(inode)->fid)); - if (err) { - if (err == FFS_PERMISSIONERR) - err = -EPERM; - else - err = -EIO; + if (err) goto out; - } + INC_IVERSION(dir); - dir->i_mtime = dir->i_atime = current_time(dir); + curtime = current_time(dir); + dir->i_mtime = curtime; + dir->i_atime = curtime; if (IS_DIRSYNC(dir)) (void)exfat_sync_inode(dir); else mark_inode_dirty(dir); clear_nlink(inode); - inode->i_mtime = inode->i_atime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; exfat_detach(inode); remove_inode_hash(inode); @@ -2560,6 +2429,7 @@ static int exfat_symlink(struct inode *dir, struct dentry *dentry, const char *target) { struct super_block *sb = dir->i_sb; + struct timespec64 curtime; struct inode *inode; struct file_id_t fid; loff_t i_pos; @@ -2572,32 +2442,22 @@ static int exfat_symlink(struct inode *dir, struct dentry *dentry, pr_debug("%s entered\n", __func__); err = ffsCreateFile(dir, (u8 *)dentry->d_name.name, FM_SYMLINK, &fid); - if (err) { - if (err == FFS_INVALIDPATH) - err = -EINVAL; - else if (err == FFS_FILEEXIST) - err = -EEXIST; - else if (err == FFS_FULL) - err = -ENOSPC; - else - err = -EIO; + if (err) goto out; - } + err = ffsWriteFile(dir, &fid, (char *)target, len, &ret); if (err) { ffsRemoveFile(dir, &fid); - - if (err == FFS_FULL) - err = -ENOSPC; - else - err = -EIO; goto out; } INC_IVERSION(dir); - dir->i_ctime = dir->i_mtime = dir->i_atime = current_time(dir); + curtime = current_time(dir); + dir->i_ctime = curtime; + dir->i_mtime = curtime; + dir->i_atime = curtime; if (IS_DIRSYNC(dir)) (void)exfat_sync_inode(dir); else @@ -2611,7 +2471,10 @@ static int exfat_symlink(struct inode *dir, struct dentry *dentry, goto out; } INC_IVERSION(inode); - inode->i_mtime = inode->i_atime = inode->i_ctime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; + inode->i_ctime = curtime; /* timestamp is already written, so mark_inode_dirty() is unneeded. */ EXFAT_I(inode)->target = kmemdup(target, len + 1, GFP_KERNEL); @@ -2632,6 +2495,7 @@ out: static int exfat_mkdir(struct inode *dir, struct dentry *dentry, umode_t mode) { struct super_block *sb = dir->i_sb; + struct timespec64 curtime; struct inode *inode; struct file_id_t fid; loff_t i_pos; @@ -2642,21 +2506,14 @@ static int exfat_mkdir(struct inode *dir, struct dentry *dentry, umode_t mode) pr_debug("%s entered\n", __func__); err = ffsCreateDir(dir, (u8 *)dentry->d_name.name, &fid); - if (err) { - if (err == FFS_INVALIDPATH) - err = -EINVAL; - else if (err == FFS_FILEEXIST) - err = -EEXIST; - else if (err == FFS_FULL) - err = -ENOSPC; - else if (err == FFS_NAMETOOLONG) - err = -ENAMETOOLONG; - else - err = -EIO; + if (err) goto out; - } + INC_IVERSION(dir); - dir->i_ctime = dir->i_mtime = dir->i_atime = current_time(dir); + curtime = current_time(dir); + dir->i_ctime = curtime; + dir->i_mtime = curtime; + dir->i_atime = curtime; if (IS_DIRSYNC(dir)) (void)exfat_sync_inode(dir); else @@ -2671,7 +2528,10 @@ static int exfat_mkdir(struct inode *dir, struct dentry *dentry, umode_t mode) goto out; } INC_IVERSION(inode); - inode->i_mtime = inode->i_atime = inode->i_ctime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; + inode->i_ctime = curtime; /* timestamp is already written, so mark_inode_dirty() is unneeded. */ dentry->d_time = GET_IVERSION(dentry->d_parent->d_inode); @@ -2687,6 +2547,7 @@ static int exfat_rmdir(struct inode *dir, struct dentry *dentry) { struct inode *inode = dentry->d_inode; struct super_block *sb = dir->i_sb; + struct timespec64 curtime; int err; __lock_super(sb); @@ -2696,21 +2557,13 @@ static int exfat_rmdir(struct inode *dir, struct dentry *dentry) EXFAT_I(inode)->fid.size = i_size_read(inode); err = ffsRemoveDir(dir, &(EXFAT_I(inode)->fid)); - if (err) { - if (err == FFS_INVALIDPATH) - err = -EINVAL; - else if (err == FFS_FILEEXIST) - err = -ENOTEMPTY; - else if (err == FFS_NOTFOUND) - err = -ENOENT; - else if (err == FFS_DIRBUSY) - err = -EBUSY; - else - err = -EIO; + if (err) goto out; - } + INC_IVERSION(dir); - dir->i_mtime = dir->i_atime = current_time(dir); + curtime = current_time(dir); + dir->i_mtime = curtime; + dir->i_atime = curtime; if (IS_DIRSYNC(dir)) (void)exfat_sync_inode(dir); else @@ -2718,7 +2571,9 @@ static int exfat_rmdir(struct inode *dir, struct dentry *dentry) drop_nlink(dir); clear_nlink(inode); - inode->i_mtime = inode->i_atime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; exfat_detach(inode); remove_inode_hash(inode); @@ -2734,6 +2589,7 @@ static int exfat_rename(struct inode *old_dir, struct dentry *old_dentry, { struct inode *old_inode, *new_inode; struct super_block *sb = old_dir->i_sb; + struct timespec64 curtime; loff_t i_pos; int err; @@ -2751,24 +2607,15 @@ static int exfat_rename(struct inode *old_dir, struct dentry *old_dentry, err = ffsMoveFile(old_dir, &(EXFAT_I(old_inode)->fid), new_dir, new_dentry); - if (err) { - if (err == FFS_PERMISSIONERR) - err = -EPERM; - else if (err == FFS_INVALIDPATH) - err = -EINVAL; - else if (err == FFS_FILEEXIST) - err = -EEXIST; - else if (err == FFS_NOTFOUND) - err = -ENOENT; - else if (err == FFS_FULL) - err = -ENOSPC; - else - err = -EIO; + if (err) goto out; - } + INC_IVERSION(new_dir); - new_dir->i_ctime = new_dir->i_mtime = new_dir->i_atime = - current_time(new_dir); + curtime = current_time(new_dir); + new_dir->i_ctime = curtime; + new_dir->i_mtime = curtime; + new_dir->i_atime = curtime; + if (IS_DIRSYNC(new_dir)) (void)exfat_sync_inode(new_dir); else @@ -2790,7 +2637,9 @@ static int exfat_rename(struct inode *old_dir, struct dentry *old_dentry, inc_nlink(new_dir); } INC_IVERSION(old_dir); - old_dir->i_ctime = old_dir->i_mtime = current_time(old_dir); + curtime = current_time(old_dir); + old_dir->i_ctime = curtime; + old_dir->i_mtime = curtime; if (IS_DIRSYNC(old_dir)) (void)exfat_sync_inode(old_dir); else @@ -2814,13 +2663,16 @@ static int exfat_cont_expand(struct inode *inode, loff_t size) { struct address_space *mapping = inode->i_mapping; loff_t start = i_size_read(inode), count = size - i_size_read(inode); + struct timespec64 curtime; int err, err2; err = generic_cont_expand_simple(inode, size); if (err != 0) return err; - inode->i_ctime = inode->i_mtime = current_time(inode); + curtime = current_time(inode); + inode->i_ctime = curtime; + inode->i_mtime = curtime; mark_inode_dirty(inode); if (IS_SYNC(inode)) { @@ -2895,7 +2747,8 @@ static void exfat_truncate(struct inode *inode, loff_t old_size) { struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct fs_info_t *p_fs = &(sbi->fs_info); + struct fs_info_t *p_fs = &sbi->fs_info; + struct timespec64 curtime; int err; __lock_super(sb); @@ -2914,7 +2767,9 @@ static void exfat_truncate(struct inode *inode, loff_t old_size) if (err) goto out; - inode->i_ctime = inode->i_mtime = current_time(inode); + curtime = current_time(inode); + inode->i_ctime = curtime; + inode->i_mtime = curtime; if (IS_DIRSYNC(inode)) (void)exfat_sync_inode(inode); else @@ -2936,8 +2791,8 @@ static int exfat_setattr(struct dentry *dentry, struct iattr *attr) pr_debug("%s entered\n", __func__); - if ((attr->ia_valid & ATTR_SIZE) - && (attr->ia_size > i_size_read(inode))) { + if ((attr->ia_valid & ATTR_SIZE) && + attr->ia_size > i_size_read(inode)) { error = exfat_cont_expand(inode, attr->ia_size); if (error || attr->ia_valid == ATTR_SIZE) return error; @@ -2946,8 +2801,8 @@ static int exfat_setattr(struct dentry *dentry, struct iattr *attr) ia_valid = attr->ia_valid; - if ((ia_valid & (ATTR_MTIME_SET | ATTR_ATIME_SET | ATTR_TIMES_SET)) - && exfat_allow_set_time(sbi, inode)) { + if ((ia_valid & (ATTR_MTIME_SET | ATTR_ATIME_SET | ATTR_TIMES_SET)) && + exfat_allow_set_time(sbi, inode)) { attr->ia_valid &= ~(ATTR_MTIME_SET | ATTR_ATIME_SET | ATTR_TIMES_SET); @@ -3073,8 +2928,7 @@ static int exfat_bmap(struct inode *inode, sector_t sector, sector_t *phys, { struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct fs_info_t *p_fs = &(sbi->fs_info); - struct bd_info_t *p_bd = &(sbi->bd_info); + struct fs_info_t *p_fs = &sbi->fs_info; const unsigned long blocksize = sb->s_blocksize; const unsigned char blocksize_bits = sb->s_blocksize_bits; sector_t last_block; @@ -3084,18 +2938,6 @@ static int exfat_bmap(struct inode *inode, sector_t sector, sector_t *phys, *phys = 0; *mapped_blocks = 0; - if ((p_fs->vol_type == FAT12) || (p_fs->vol_type == FAT16)) { - if (inode->i_ino == EXFAT_ROOT_INO) { - if (sector < - (p_fs->dentries_in_root >> - (p_bd->sector_size_bits - DENTRY_SIZE_BITS))) { - *phys = sector + p_fs->root_start_sector; - *mapped_blocks = 1; - } - return 0; - } - } - last_block = (i_size_read(inode) + (blocksize - 1)) >> blocksize_bits; if (sector >= last_block) { if (*create == 0) @@ -3114,12 +2956,7 @@ static int exfat_bmap(struct inode *inode, sector_t sector, sector_t *phys, err = ffsMapCluster(inode, clu_offset, &cluster); - if (err) { - if (err == FFS_FULL) - return -ENOSPC; - else - return -EIO; - } else if (cluster != CLUSTER_32(~0)) { + if (!err && (cluster != CLUSTER_32(~0))) { *phys = START_SECTOR(cluster) + sec_offset; *mapped_blocks = p_fs->sectors_per_clu - sec_offset; } @@ -3215,6 +3052,7 @@ static int exfat_write_end(struct file *file, struct address_space *mapping, { struct inode *inode = mapping->host; struct file_id_t *fid = &(EXFAT_I(inode)->fid); + struct timespec64 curtime; int err; err = generic_write_end(file, mapping, pos, len, copied, pagep, fsdata); @@ -3223,7 +3061,9 @@ static int exfat_write_end(struct file *file, struct address_space *mapping, exfat_write_failed(mapping, pos + len); if (!(err < 0) && !(fid->attr & ATTR_ARCHIVE)) { - inode->i_mtime = inode->i_ctime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_ctime = curtime; fid->attr |= ATTR_ARCHIVE; mark_inode_dirty(inode); } @@ -3302,7 +3142,7 @@ static struct inode *exfat_iget(struct super_block *sb, loff_t i_pos) static int exfat_fill_inode(struct inode *inode, struct file_id_t *fid) { struct exfat_sb_info *sbi = EXFAT_SB(inode->i_sb); - struct fs_info_t *p_fs = &(sbi->fs_info); + struct fs_info_t *p_fs = &sbi->fs_info; struct dir_entry_t info; memcpy(&(EXFAT_I(inode)->fid), fid, sizeof(struct file_id_t)); @@ -3314,7 +3154,7 @@ static int exfat_fill_inode(struct inode *inode, struct file_id_t *fid) inode->i_uid = sbi->options.fs_uid; inode->i_gid = sbi->options.fs_gid; INC_IVERSION(inode); - inode->i_generation = get_seconds(); + inode->i_generation = prandom_u32(); if (info.Attr & ATTR_SUBDIR) { /* directory */ inode->i_generation &= ~1; @@ -3501,7 +3341,7 @@ static int exfat_statfs(struct dentry *dentry, struct kstatfs *buf) struct vol_info_t info; if (p_fs->used_clusters == UINT_MAX) { - if (ffsGetVolInfo(sb, &info) == FFS_MEDIAERR) + if (ffsGetVolInfo(sb, &info) == -EIO) return -EIO; } else { @@ -3557,7 +3397,7 @@ static int exfat_show_options(struct seq_file *m, struct dentry *root) seq_puts(m, ",errors=panic"); else seq_puts(m, ",errors=remount-ro"); -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD if (opts->discard) seq_puts(m, ",discard"); #endif @@ -3638,7 +3478,7 @@ enum { Opt_err_ro, Opt_utf8_hack, Opt_err, -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD Opt_discard, #endif /* EXFAT_CONFIG_DISCARD */ }; @@ -3658,9 +3498,9 @@ static const match_table_t exfat_tokens = { {Opt_err_panic, "errors=panic"}, {Opt_err_ro, "errors=remount-ro"}, {Opt_utf8_hack, "utf8"}, -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD {Opt_discard, "discard"}, -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ {Opt_err, NULL} }; @@ -3674,13 +3514,14 @@ static int parse_options(char *options, int silent, int *debug, opts->fs_uid = current_uid(); opts->fs_gid = current_gid(); - opts->fs_fmask = opts->fs_dmask = current->fs->umask; + opts->fs_fmask = current->fs->umask; + opts->fs_dmask = current->fs->umask; opts->allow_utime = U16_MAX; opts->codepage = exfat_default_codepage; opts->iocharset = exfat_default_iocharset; opts->casesensitive = 0; opts->errors = EXFAT_ERRORS_RO; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD opts->discard = 0; #endif *debug = 0; @@ -3751,11 +3592,11 @@ static int parse_options(char *options, int silent, int *debug, case Opt_debug: *debug = 1; break; -#ifdef CONFIG_EXFAT_DISCARD +#ifdef CONFIG_STAGING_EXFAT_DISCARD case Opt_discard: opts->discard = 1; break; -#endif /* CONFIG_EXFAT_DISCARD */ +#endif /* CONFIG_STAGING_EXFAT_DISCARD */ case Opt_utf8_hack: break; default: @@ -3787,7 +3628,8 @@ static int exfat_read_root(struct inode *inode) { struct super_block *sb = inode->i_sb; struct exfat_sb_info *sbi = EXFAT_SB(sb); - struct fs_info_t *p_fs = &(sbi->fs_info); + struct fs_info_t *p_fs = &sbi->fs_info; + struct timespec64 curtime; struct dir_entry_t info; EXFAT_I(inode)->fid.dir.dir = p_fs->root_dir; @@ -3818,7 +3660,10 @@ static int exfat_read_root(struct inode *inode) EXFAT_I(inode)->mmu_private = i_size_read(inode); exfat_save_attr(inode, ATTR_SUBDIR); - inode->i_mtime = inode->i_atime = inode->i_ctime = current_time(inode); + curtime = current_time(inode); + inode->i_mtime = curtime; + inode->i_atime = curtime; + inode->i_ctime = curtime; set_nlink(inode, info.NumSubdirs + 2); return 0; @@ -3838,7 +3683,6 @@ static int exfat_fill_super(struct super_block *sb, void *data, int silent) struct exfat_sb_info *sbi; int debug, ret; long error; - char buf[50]; /* * GFP_KERNEL is ok here, because while we do hold the @@ -3885,17 +3729,6 @@ static int exfat_fill_super(struct super_block *sb, void *data, int silent) * if (FAT_FIRST_ENT(sb, media) != first) */ - /* codepage is not meaningful in exfat */ - if (sbi->fs_info.vol_type != EXFAT) { - error = -EINVAL; - sprintf(buf, "cp%d", sbi->options.codepage); - sbi->nls_disk = load_nls(buf); - if (!sbi->nls_disk) { - pr_err("[EXFAT] Codepage %s not found\n", buf); - goto out_fail2; - } - } - sbi->nls_io = load_nls(sbi->options.iocharset); error = -ENOMEM; @@ -3967,7 +3800,7 @@ static void __exit exfat_destroy_inodecache(void) kmem_cache_destroy(exfat_inode_cachep); } -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG static void exfat_debug_kill_sb(struct super_block *sb) { struct exfat_sb_info *sbi = EXFAT_SB(sb); @@ -3984,10 +3817,10 @@ static void exfat_debug_kill_sb(struct super_block *sb) * invalidate_bdev drops all device cache include * dirty. We use this to simulate device removal. */ - down(&p_fs->v_sem); - FAT_release_all(sb); - buf_release_all(sb); - up(&p_fs->v_sem); + mutex_lock(&p_fs->v_mutex); + exfat_fat_release_all(sb); + exfat_buf_release_all(sb); + mutex_unlock(&p_fs->v_mutex); invalidate_bdev(bdev); } @@ -3995,17 +3828,17 @@ static void exfat_debug_kill_sb(struct super_block *sb) kill_block_super(sb); } -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ static struct file_system_type exfat_fs_type = { .owner = THIS_MODULE, .name = "exfat", .mount = exfat_fs_mount, -#ifdef CONFIG_EXFAT_KERNEL_DEBUG +#ifdef CONFIG_STAGING_EXFAT_KERNEL_DEBUG .kill_sb = exfat_debug_kill_sb, #else .kill_sb = kill_block_super, -#endif /* CONFIG_EXFAT_KERNEL_DEBUG */ +#endif /* CONFIG_STAGING_EXFAT_KERNEL_DEBUG */ .fs_flags = FS_REQUIRES_DEV, }; diff --git a/drivers/staging/greybus/Kconfig b/drivers/staging/greybus/Kconfig index d4777f5..9389e7a 100644 --- a/drivers/staging/greybus/Kconfig +++ b/drivers/staging/greybus/Kconfig @@ -4,7 +4,7 @@ if GREYBUS config GREYBUS_AUDIO tristate "Greybus Audio Class driver" depends on SOUND - ---help--- + help Select this option if you have a device that follows the Greybus Audio Class specification. @@ -13,7 +13,7 @@ config GREYBUS_AUDIO config GREYBUS_BOOTROM tristate "Greybus Bootrom Class driver" - ---help--- + help Select this option if you have a device that follows the Greybus Bootrom Class specification. @@ -23,7 +23,7 @@ config GREYBUS_BOOTROM config GREYBUS_CAMERA tristate "Greybus Camera Class driver" depends on MEDIA_SUPPORT && LEDS_CLASS_FLASH && BROKEN - ---help--- + help Select this option if you have a device that follows the Greybus Camera Class specification. @@ -33,7 +33,7 @@ config GREYBUS_CAMERA config GREYBUS_FIRMWARE tristate "Greybus Firmware Download Class driver" depends on SPI - ---help--- + help Select this option if you have a device that follows the Greybus Firmware Download Class specification. @@ -43,7 +43,7 @@ config GREYBUS_FIRMWARE config GREYBUS_HID tristate "Greybus HID Class driver" depends on HID && INPUT - ---help--- + help Select this option if you have a device that follows the Greybus HID Class specification. @@ -53,7 +53,7 @@ config GREYBUS_HID config GREYBUS_LIGHT tristate "Greybus LED Class driver" depends on LEDS_CLASS - ---help--- + help Select this option if you have a device that follows the Greybus LED Class specification. @@ -62,7 +62,7 @@ config GREYBUS_LIGHT config GREYBUS_LOG tristate "Greybus Debug Log Class driver" - ---help--- + help Select this option if you have a device that follows the Greybus Debug Log Class specification. @@ -71,7 +71,7 @@ config GREYBUS_LOG config GREYBUS_LOOPBACK tristate "Greybus Loopback Class driver" - ---help--- + help Select this option if you have a device that follows the Greybus Debug Log Class specification. @@ -81,7 +81,7 @@ config GREYBUS_LOOPBACK config GREYBUS_POWER tristate "Greybus Powersupply Class driver" depends on POWER_SUPPLY - ---help--- + help Select this option if you have a device that follows the Greybus Powersupply Class specification. @@ -90,7 +90,7 @@ config GREYBUS_POWER config GREYBUS_RAW tristate "Greybus Raw Class driver" - ---help--- + help Select this option if you have a device that follows the Greybus Raw Class specification. @@ -99,7 +99,7 @@ config GREYBUS_RAW config GREYBUS_VIBRATOR tristate "Greybus Vibrator Motor Class driver" - ---help--- + help Select this option if you have a device that follows the Greybus Vibrator Motor Class specification. @@ -108,7 +108,7 @@ config GREYBUS_VIBRATOR menuconfig GREYBUS_BRIDGED_PHY tristate "Greybus Bridged PHY Class drivers" - ---help--- + help Select this option to pick from a variety of Greybus Bridged PHY class drivers. These drivers emulate a number of different "traditional" busses by tunneling them over Greybus. @@ -123,7 +123,7 @@ config GREYBUS_GPIO tristate "Greybus GPIO Bridged PHY driver" depends on GPIOLIB select GPIOLIB_IRQCHIP - ---help--- + help Select this option if you have a device that follows the Greybus GPIO Bridged PHY Class specification. @@ -133,7 +133,7 @@ config GREYBUS_GPIO config GREYBUS_I2C tristate "Greybus I2C Bridged PHY driver" depends on I2C - ---help--- + help Select this option if you have a device that follows the Greybus I2C Bridged PHY Class specification. @@ -143,7 +143,7 @@ config GREYBUS_I2C config GREYBUS_PWM tristate "Greybus PWM Bridged PHY driver" depends on PWM - ---help--- + help Select this option if you have a device that follows the Greybus PWM Bridged PHY Class specification. @@ -153,7 +153,7 @@ config GREYBUS_PWM config GREYBUS_SDIO tristate "Greybus SDIO Bridged PHY driver" depends on MMC - ---help--- + help Select this option if you have a device that follows the Greybus SDIO Bridged PHY Class specification. @@ -163,7 +163,7 @@ config GREYBUS_SDIO config GREYBUS_SPI tristate "Greybus SPI Bridged PHY driver" depends on SPI - ---help--- + help Select this option if you have a device that follows the Greybus SPI Bridged PHY Class specification. @@ -173,7 +173,7 @@ config GREYBUS_SPI config GREYBUS_UART tristate "Greybus UART Bridged PHY driver" depends on TTY - ---help--- + help Select this option if you have a device that follows the Greybus UART Bridged PHY Class specification. @@ -183,7 +183,7 @@ config GREYBUS_UART config GREYBUS_USB tristate "Greybus USB Host Bridged PHY driver" depends on USB - ---help--- + help Select this option if you have a device that follows the Greybus USB Host Bridged PHY Class specification. @@ -195,7 +195,7 @@ endif # GREYBUS_BRIDGED_PHY config GREYBUS_ARCHE tristate "Greybus Arche Platform driver" depends on USB_HSIC_USB3613 || COMPILE_TEST - ---help--- + help Select this option if you have an Arche device. To compile this code as a module, chose M here: the module diff --git a/drivers/staging/greybus/audio_apbridgea.h b/drivers/staging/greybus/audio_apbridgea.h index 3f1f4dd..efec0f8 100644 --- a/drivers/staging/greybus/audio_apbridgea.h +++ b/drivers/staging/greybus/audio_apbridgea.h @@ -65,7 +65,7 @@ struct audio_apbridgea_hdr { __u8 type; __le16 i2s_port; - __u8 data[0]; + __u8 data[]; } __packed; struct audio_apbridgea_set_config_request { diff --git a/drivers/staging/greybus/gpio.c b/drivers/staging/greybus/gpio.c index 1ff34ab..36d99f9 100644 --- a/drivers/staging/greybus/gpio.c +++ b/drivers/staging/greybus/gpio.c @@ -364,8 +364,7 @@ static int gb_gpio_request_handler(struct gb_operation *op) struct gb_message *request; struct gb_gpio_irq_event_request *event; u8 type = op->type; - int irq; - struct irq_desc *desc; + int irq, ret; if (type != GB_GPIO_TYPE_IRQ_EVENT) { dev_err(dev, "unsupported unsolicited request: %u\n", type); @@ -391,17 +390,15 @@ static int gb_gpio_request_handler(struct gb_operation *op) dev_err(dev, "failed to find IRQ\n"); return -EINVAL; } - desc = irq_to_desc(irq); - if (!desc) { - dev_err(dev, "failed to look up irq\n"); - return -EINVAL; - } local_irq_disable(); - generic_handle_irq_desc(desc); + ret = generic_handle_irq(irq); local_irq_enable(); - return 0; + if (ret) + dev_err(dev, "failed to invoke irq handler\n"); + + return ret; } static int gb_gpio_request(struct gpio_chip *chip, unsigned int offset) diff --git a/drivers/staging/greybus/hid.c b/drivers/staging/greybus/hid.c index 04bfd91..ed706f3 100644 --- a/drivers/staging/greybus/hid.c +++ b/drivers/staging/greybus/hid.c @@ -290,9 +290,8 @@ static int gb_hid_parse(struct hid_device *hid) } rdesc = kzalloc(rsize, GFP_KERNEL); - if (!rdesc) { + if (!rdesc) return -ENOMEM; - } ret = gb_hid_get_report_desc(ghid, rdesc); if (ret) { diff --git a/drivers/staging/greybus/i2c.c b/drivers/staging/greybus/i2c.c index ab06fc3..de2f651 100644 --- a/drivers/staging/greybus/i2c.c +++ b/drivers/staging/greybus/i2c.c @@ -215,20 +215,6 @@ static int gb_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, return gb_i2c_transfer_operation(gb_i2c_dev, msgs, msg_count); } -#if 0 -/* Later */ -static int gb_i2c_smbus_xfer(struct i2c_adapter *adap, - u16 addr, unsigned short flags, char read_write, - u8 command, int size, union i2c_smbus_data *data) -{ - struct gb_i2c_device *gb_i2c_dev; - - gb_i2c_dev = i2c_get_adapdata(adap); - - return 0; -} -#endif - static u32 gb_i2c_functionality(struct i2c_adapter *adap) { struct gb_i2c_device *gb_i2c_dev = i2c_get_adapdata(adap); @@ -238,7 +224,6 @@ static u32 gb_i2c_functionality(struct i2c_adapter *adap) static const struct i2c_algorithm gb_i2c_algorithm = { .master_xfer = gb_i2c_master_xfer, - /* .smbus_xfer = gb_i2c_smbus_xfer, */ .functionality = gb_i2c_functionality, }; @@ -281,7 +266,6 @@ static int gb_i2c_probe(struct gbphy_device *gbphy_dev, adapter->owner = THIS_MODULE; adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adapter->algo = &gb_i2c_algorithm; - /* adapter->algo_data = what? */ adapter->dev.parent = &gbphy_dev->dev; snprintf(adapter->name, sizeof(adapter->name), "Greybus i2c adapter"); diff --git a/drivers/staging/greybus/loopback.c b/drivers/staging/greybus/loopback.c index 583d970..2471448 100644 --- a/drivers/staging/greybus/loopback.c +++ b/drivers/staging/greybus/loopback.c @@ -135,7 +135,7 @@ static ssize_t name##_##field##_show(struct device *dev, \ char *buf) \ { \ struct gb_loopback *gb = dev_get_drvdata(dev); \ - /* Report 0 for min and max if no transfer successed */ \ + /* Report 0 for min and max if no transfer succeeded */ \ if (!gb->requests_completed) \ return sprintf(buf, "0\n"); \ return sprintf(buf, "%" #type "\n", gb->name.field); \ diff --git a/drivers/staging/greybus/raw.c b/drivers/staging/greybus/raw.c index 64a17df..2a375f4 100644 --- a/drivers/staging/greybus/raw.c +++ b/drivers/staging/greybus/raw.c @@ -29,7 +29,7 @@ struct gb_raw { struct raw_data { struct list_head entry; u32 len; - u8 data[0]; + u8 data[]; }; static struct class *raw_class; diff --git a/drivers/staging/greybus/sdio.c b/drivers/staging/greybus/sdio.c index c4b16bb..0939f4a 100644 --- a/drivers/staging/greybus/sdio.c +++ b/drivers/staging/greybus/sdio.c @@ -67,7 +67,6 @@ static void _gb_sdio_set_host_caps(struct gb_sdio_host *host, u32 r) ((r & GB_SDIO_CAP_8_BIT_DATA) ? MMC_CAP_8_BIT_DATA : 0) | ((r & GB_SDIO_CAP_MMC_HS) ? MMC_CAP_MMC_HIGHSPEED : 0) | ((r & GB_SDIO_CAP_SD_HS) ? MMC_CAP_SD_HIGHSPEED : 0) | - ((r & GB_SDIO_CAP_ERASE) ? MMC_CAP_ERASE : 0) | ((r & GB_SDIO_CAP_1_2V_DDR) ? MMC_CAP_1_2V_DDR : 0) | ((r & GB_SDIO_CAP_1_8V_DDR) ? MMC_CAP_1_8V_DDR : 0) | ((r & GB_SDIO_CAP_POWER_OFF_CARD) ? MMC_CAP_POWER_OFF_CARD : 0) | diff --git a/drivers/staging/greybus/tools/.gitignore b/drivers/staging/greybus/tools/.gitignore index 023654c..1fd364a 100644 --- a/drivers/staging/greybus/tools/.gitignore +++ b/drivers/staging/greybus/tools/.gitignore @@ -1 +1,2 @@ +# SPDX-License-Identifier: GPL-2.0-only loopback_test diff --git a/drivers/staging/greybus/tools/loopback_test.c b/drivers/staging/greybus/tools/loopback_test.c index 69c6dce..867bf28 100644 --- a/drivers/staging/greybus/tools/loopback_test.c +++ b/drivers/staging/greybus/tools/loopback_test.c @@ -802,8 +802,9 @@ static void prepare_devices(struct loopback_test *t) write_sysfs_val(t->devices[i].sysfs_entry, "outstanding_operations_max", t->async_outstanding_operations); - } else + } else { write_sysfs_val(t->devices[i].sysfs_entry, "async", 0); + } } } diff --git a/drivers/staging/greybus/uart.c b/drivers/staging/greybus/uart.c index 4ffb334..607378b 100644 --- a/drivers/staging/greybus/uart.c +++ b/drivers/staging/greybus/uart.c @@ -40,14 +40,6 @@ #define GB_UART_FIRMWARE_CREDITS 4096 #define GB_UART_CREDIT_WAIT_TIMEOUT_MSEC 10000 -struct gb_tty_line_coding { - __le32 rate; - __u8 format; - __u8 parity; - __u8 data_bits; - __u8 flow_control; -}; - struct gb_tty { struct gbphy_device *gbphy_dev; struct tty_port port; @@ -66,7 +58,7 @@ struct gb_tty { struct mutex mutex; u8 ctrlin; /* input control lines */ u8 ctrlout; /* output control lines */ - struct gb_tty_line_coding line_coding; + struct gb_uart_set_line_coding_request line_coding; struct work_struct tx_work; struct kfifo write_fifo; bool close_pending; @@ -288,12 +280,9 @@ static void gb_uart_tx_write_work(struct work_struct *work) static int send_line_coding(struct gb_tty *tty) { - struct gb_uart_set_line_coding_request request; - - memcpy(&request, &tty->line_coding, - sizeof(tty->line_coding)); return gb_operation_sync(tty->connection, GB_UART_TYPE_SET_LINE_CODING, - &request, sizeof(request), NULL, 0); + &tty->line_coding, sizeof(tty->line_coding), + NULL, 0); } static int send_control(struct gb_tty *gb_tty, u8 control) @@ -493,9 +482,9 @@ static int gb_tty_break_ctl(struct tty_struct *tty, int state) static void gb_tty_set_termios(struct tty_struct *tty, struct ktermios *termios_old) { + struct gb_uart_set_line_coding_request newline; struct gb_tty *gb_tty = tty->driver_data; struct ktermios *termios = &tty->termios; - struct gb_tty_line_coding newline; u8 newctrl = gb_tty->ctrlout; newline.rate = cpu_to_le32(tty_get_baud_rate(tty)); diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 836e736..5f3b0d0 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -1508,10 +1508,10 @@ static int __init omap8250_console_fixup(void) } add_preferred_console("ttyS", idx, options); - pr_err("WARNING: Your 'console=ttyO%d' has been replaced by 'ttyS%d'\n", + pr_info("WARNING: Your 'console=ttyO%d' has been replaced by 'ttyS%d'\n", idx, idx); - pr_err("This ensures that you still see kernel messages. Please\n"); - pr_err("update your kernel commandline.\n"); + pr_info("This ensures that you still see kernel messages. Please\n"); + pr_info("update your kernel commandline.\n"); return 0; } console_initcall(omap8250_console_fixup); diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index 275568a..266957d 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -46,6 +46,7 @@ config USB depends on USB_ARCH_HAS_HCD select GENERIC_ALLOCATOR select USB_COMMON + select POWER_SEQUENCE select NLS # for UTF-8 strings ---help--- Universal Serial Bus (USB) is a specification for a serial bus diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 4d3de33..ba1d47b 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -29,6 +29,7 @@ #include #include #include +#include #include #include @@ -1713,6 +1714,7 @@ static void hub_disconnect(struct usb_interface *intf) hub->error = 0; hub_quiesce(hub, HUB_DISCONNECT); + of_pwrseq_off_list(&hub->pwrseq_on_list); mutex_lock(&usb_port_peer_mutex); /* Avoid races with recursively_mark_NOTATTACHED() */ @@ -1763,11 +1765,41 @@ static bool hub_descriptor_is_sane(struct usb_host_interface *desc) return true; } +#ifdef CONFIG_OF +static int hub_of_pwrseq_on(struct usb_hub *hub) +{ + struct device *parent; + struct usb_device *hdev = hub->hdev; + struct device_node *np; + int ret; + + if (hdev->parent) + parent = &hdev->dev; + else + parent = bus_to_hcd(hdev->bus)->self.sysdev; + + for_each_child_of_node(parent->of_node, np) { + ret = of_pwrseq_on_list(np, &hub->pwrseq_on_list); + /* Maybe no power sequence library is chosen */ + if (ret && ret != -ENOENT) + return ret; + } + + return 0; +} +#else +static int hub_of_pwrseq_on(struct usb_hub *hub) +{ + return 0; +} +#endif + static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) { struct usb_host_interface *desc; struct usb_device *hdev; struct usb_hub *hub; + int ret = -ENODEV; desc = intf->cur_altsetting; hdev = interface_to_usbdev(intf); @@ -1858,6 +1890,7 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) INIT_DELAYED_WORK(&hub->leds, led_work); INIT_DELAYED_WORK(&hub->init_work, NULL); INIT_WORK(&hub->events, hub_event); + INIT_LIST_HEAD(&hub->pwrseq_on_list); spin_lock_init(&hub->irq_urb_lock); timer_setup(&hub->irq_urb_retry, hub_retry_irq_urb, 0); usb_get_intf(intf); @@ -1878,11 +1911,14 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) usb_autopm_get_interface_no_resume(intf); } - if (hub_configure(hub, &desc->endpoint[0].desc) >= 0) - return 0; + if (hub_configure(hub, &desc->endpoint[0].desc) >= 0) { + ret = hub_of_pwrseq_on(hub); + if (!ret) + return 0; + } hub_disconnect(intf); - return -ENODEV; + return ret; } static int @@ -3744,7 +3780,7 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg) /* stop hub_wq and related activity */ hub_quiesce(hub, HUB_SUSPEND); - return 0; + return pwrseq_suspend_list(&hub->pwrseq_on_list); } /* Report wakeup requests from the ports of a resuming root hub */ @@ -3784,8 +3820,13 @@ static void report_wakeup_requests(struct usb_hub *hub) static int hub_resume(struct usb_interface *intf) { struct usb_hub *hub = usb_get_intfdata(intf); + int ret; dev_dbg(&intf->dev, "%s\n", __func__); + ret = pwrseq_resume_list(&hub->pwrseq_on_list); + if (ret) + return ret; + hub_activate(hub, HUB_RESUME); /* diff --git a/drivers/usb/core/hub.h b/drivers/usb/core/hub.h index a97dd1b..b34ea39 100644 --- a/drivers/usb/core/hub.h +++ b/drivers/usb/core/hub.h @@ -73,6 +73,7 @@ struct usb_hub { spinlock_t irq_urb_lock; struct timer_list irq_urb_retry; struct usb_port **ports; + struct list_head pwrseq_on_list; /* powered pwrseq node list */ }; /** diff --git b/include/dt-bindings/board/am335x-bbw-bbb-base.h b/include/dt-bindings/board/am335x-bbw-bbb-base.h new file mode 100644 index 0000000..35f6d57 --- /dev/null +++ b/include/dt-bindings/board/am335x-bbw-bbb-base.h @@ -0,0 +1,103 @@ +/* + * This header provides constants for bbw/bbb pinctrl bindings. + * + * Copyright (C) 2014 Robert Nelson + * + * Numbers Based on: https://github.com/derekmolloy/boneDeviceTree/tree/master/docs + */ + +#ifndef _DT_BINDINGS_BOARD_AM335X_BBW_BBB_BASE_H +#define _DT_BINDINGS_BOARD_AM335X_BBW_BBB_BASE_H + +#define BONE_P8_03 0x018 +#define BONE_P8_04 0x01C + +#define BONE_P8_05 0x008 +#define BONE_P8_06 0x00C +#define BONE_P8_07 0x090 +#define BONE_P8_08 0x094 + +#define BONE_P8_09 0x09C +#define BONE_P8_10 0x098 +#define BONE_P8_11 0x034 +#define BONE_P8_12 0x030 + +#define BONE_P8_13 0x024 +#define BONE_P8_14 0x028 +#define BONE_P8_15 0x03C +#define BONE_P8_16 0x038 + +#define BONE_P8_17 0x02C +#define BONE_P8_18 0x08C +#define BONE_P8_19 0x020 +#define BONE_P8_20 0x084 + +#define BONE_P8_21 0x080 +#define BONE_P8_22 0x014 +#define BONE_P8_23 0x010 +#define BONE_P8_24 0x004 + +#define BONE_P8_25 0x000 +#define BONE_P8_26 0x07C +#define BONE_P8_27 0x0E0 +#define BONE_P8_28 0x0E8 + +#define BONE_P8_29 0x0E4 +#define BONE_P8_30 0x0EC +#define BONE_P8_31 0x0D8 +#define BONE_P8_32 0x0DC + +#define BONE_P8_33 0x0D4 +#define BONE_P8_34 0x0CC +#define BONE_P8_35 0x0D0 +#define BONE_P8_36 0x0C8 + +#define BONE_P8_37 0x0C0 +#define BONE_P8_38 0x0C4 +#define BONE_P8_39 0x0B8 +#define BONE_P8_40 0x0BC + +#define BONE_P8_41 0x0B0 +#define BONE_P8_42 0x0B4 +#define BONE_P8_43 0x0A8 +#define BONE_P8_44 0x0AC + +#define BONE_P8_45 0x0A0 +#define BONE_P8_46 0x0A4 + +#define BONE_P9_11 0x070 +#define BONE_P9_12 0x078 + +#define BONE_P9_13 0x074 +#define BONE_P9_14 0x048 +#define BONE_P9_15 0x040 +#define BONE_P9_16 0x04C + +#define BONE_P9_17 0x15C +#define BONE_P9_18 0x158 +#define BONE_P9_19 0x17C +#define BONE_P9_20 0x178 + +#define BONE_P9_21 0x154 +#define BONE_P9_22 0x150 +#define BONE_P9_23 0x044 +#define BONE_P9_24 0x184 + +#define BONE_P9_25 0x1AC +#define BONE_P9_26 0x180 +#define BONE_P9_27 0x1A4 +#define BONE_P9_28 0x19C + +#define BONE_P9_29 0x194 +#define BONE_P9_30 0x198 +#define BONE_P9_31 0x190 + +/* Shared P21 of P11 */ +#define BONE_P9_41A 0x1B4 +#define BONE_P9_41B 0x1A8 + +/* Shared P22 of P11 */ +#define BONE_P9_42A 0x164 +#define BONE_P9_42B 0x1A0 + +#endif diff --git a/include/dt-bindings/clock/omap5.h b/include/dt-bindings/clock/omap5.h index e541193..ba67206 100644 --- a/include/dt-bindings/clock/omap5.h +++ b/include/dt-bindings/clock/omap5.h @@ -86,6 +86,10 @@ #define OMAP5_UART5_CLKCTRL OMAP5_CLKCTRL_INDEX(0x170) #define OMAP5_UART6_CLKCTRL OMAP5_CLKCTRL_INDEX(0x178) +/* iva clocks */ +#define OMAP5_IVA_CLKCTRL OMAP5_CLKCTRL_INDEX(0x20) +#define OMAP5_SL2IF_CLKCTRL OMAP5_CLKCTRL_INDEX(0x28) + /* dss clocks */ #define OMAP5_DSS_CORE_CLKCTRL OMAP5_CLKCTRL_INDEX(0x20) diff --git a/include/linux/counter.h b/include/linux/counter.h index a061cdc..9dbd5df 100644 --- a/include/linux/counter.h +++ b/include/linux/counter.h @@ -290,53 +290,22 @@ struct counter_device_state { const struct attribute_group **groups; }; -/** - * struct counter_signal_read_value - Opaque Signal read value - * @buf: string representation of Signal read value - * @len: length of string in @buf - */ -struct counter_signal_read_value { - char *buf; - size_t len; -}; - -/** - * struct counter_count_read_value - Opaque Count read value - * @buf: string representation of Count read value - * @len: length of string in @buf - */ -struct counter_count_read_value { - char *buf; - size_t len; -}; - -/** - * struct counter_count_write_value - Opaque Count write value - * @buf: string representation of Count write value - */ -struct counter_count_write_value { - const char *buf; +enum counter_signal_value { + COUNTER_SIGNAL_LOW = 0, + COUNTER_SIGNAL_HIGH }; /** * struct counter_ops - Callbacks from driver * @signal_read: optional read callback for Signal attribute. The read * value of the respective Signal should be passed back via - * the val parameter. val points to an opaque type which - * should be set only by calling the - * counter_signal_read_value_set function from within the - * signal_read callback. + * the val parameter. * @count_read: optional read callback for Count attribute. The read * value of the respective Count should be passed back via - * the val parameter. val points to an opaque type which - * should be set only by calling the - * counter_count_read_value_set function from within the - * count_read callback. + * the val parameter. * @count_write: optional write callback for Count attribute. The write * value for the respective Count is passed in via the val - * parameter. val points to an opaque type which should be - * accessed only by calling the - * counter_count_write_value_get function. + * parameter. * @function_get: function to get the current count function mode. Returns * 0 on success and negative error code on error. The index * of the respective Count's returned function mode should @@ -346,7 +315,7 @@ struct counter_count_write_value { * Count's functions_list array. * @action_get: function to get the current action mode. Returns 0 on * success and negative error code on error. The index of - * the respective Signal's returned action mode should be + * the respective Synapse's returned action mode should be * passed back via the action parameter. * @action_set: function to set the action mode. action is the index of * the requested action mode from the respective Synapse's @@ -355,13 +324,11 @@ struct counter_count_write_value { struct counter_ops { int (*signal_read)(struct counter_device *counter, struct counter_signal *signal, - struct counter_signal_read_value *val); + enum counter_signal_value *val); int (*count_read)(struct counter_device *counter, - struct counter_count *count, - struct counter_count_read_value *val); + struct counter_count *count, unsigned long *val); int (*count_write)(struct counter_device *counter, - struct counter_count *count, - struct counter_count_write_value *val); + struct counter_count *count, unsigned long val); int (*function_get)(struct counter_device *counter, struct counter_count *count, size_t *function); int (*function_set)(struct counter_device *counter, @@ -477,29 +444,6 @@ struct counter_device { void *priv; }; -enum counter_signal_level { - COUNTER_SIGNAL_LEVEL_LOW = 0, - COUNTER_SIGNAL_LEVEL_HIGH -}; - -enum counter_signal_value_type { - COUNTER_SIGNAL_LEVEL = 0 -}; - -enum counter_count_value_type { - COUNTER_COUNT_POSITION = 0, -}; - -void counter_signal_read_value_set(struct counter_signal_read_value *const val, - const enum counter_signal_value_type type, - void *const data); -void counter_count_read_value_set(struct counter_count_read_value *const val, - const enum counter_count_value_type type, - void *const data); -int counter_count_write_value_get(void *const data, - const enum counter_count_value_type type, - const struct counter_count_write_value *const val); - int counter_register(struct counter_device *const counter); void counter_unregister(struct counter_device *const counter); int devm_counter_register(struct device *dev, diff --git a/include/linux/mfd/stm32-timers.h b/include/linux/mfd/stm32-timers.h index 067d146..f8db83a 100644 --- a/include/linux/mfd/stm32-timers.h +++ b/include/linux/mfd/stm32-timers.h @@ -70,14 +70,11 @@ #define TIM_CCER_CC4E BIT(12) /* Capt/Comp 4 out Ena */ #define TIM_CCER_CC4P BIT(13) /* Capt/Comp 4 Polarity */ #define TIM_CCER_CCXE (BIT(0) | BIT(4) | BIT(8) | BIT(12)) -#define TIM_BDTR_BKE BIT(12) /* Break input enable */ -#define TIM_BDTR_BKP BIT(13) /* Break input polarity */ +#define TIM_BDTR_BKE(x) BIT(12 + (x) * 12) /* Break input enable */ +#define TIM_BDTR_BKP(x) BIT(13 + (x) * 12) /* Break input polarity */ #define TIM_BDTR_AOE BIT(14) /* Automatic Output Enable */ #define TIM_BDTR_MOE BIT(15) /* Main Output Enable */ -#define TIM_BDTR_BKF (BIT(16) | BIT(17) | BIT(18) | BIT(19)) -#define TIM_BDTR_BK2F (BIT(20) | BIT(21) | BIT(22) | BIT(23)) -#define TIM_BDTR_BK2E BIT(24) /* Break 2 input enable */ -#define TIM_BDTR_BK2P BIT(25) /* Break 2 input polarity */ +#define TIM_BDTR_BKF(x) (0xf << (16 + (x) * 4)) #define TIM_DCR_DBA GENMASK(4, 0) /* DMA base addr */ #define TIM_DCR_DBL GENMASK(12, 8) /* DMA burst len */ @@ -87,8 +84,7 @@ #define TIM_CR2_MMS2_SHIFT 20 #define TIM_SMCR_TS_SHIFT 4 #define TIM_BDTR_BKF_MASK 0xF -#define TIM_BDTR_BKF_SHIFT 16 -#define TIM_BDTR_BK2F_SHIFT 20 +#define TIM_BDTR_BKF_SHIFT(x) (16 + (x) * 4) enum stm32_timers_dmas { STM32_TIMERS_DMA_CH1, diff --git a/include/linux/mmc/sdio_ids.h b/include/linux/mmc/sdio_ids.h index 08b25c0..2e9a6e4 100644 --- a/include/linux/mmc/sdio_ids.h +++ b/include/linux/mmc/sdio_ids.h @@ -41,8 +41,10 @@ #define SDIO_DEVICE_ID_BROADCOM_43455 0xa9bf #define SDIO_DEVICE_ID_BROADCOM_4354 0x4354 #define SDIO_DEVICE_ID_BROADCOM_4356 0x4356 +#define SDIO_DEVICE_ID_BROADCOM_4359 0x4359 #define SDIO_DEVICE_ID_CYPRESS_4373 0x4373 #define SDIO_DEVICE_ID_CYPRESS_43012 43012 +#define SDIO_DEVICE_ID_CYPRESS_89359 0x4355 #define SDIO_VENDOR_ID_INTEL 0x0089 #define SDIO_DEVICE_ID_INTEL_IWMC3200WIMAX 0x1402 diff --git a/include/linux/platform_data/ti-sysc.h b/include/linux/platform_data/ti-sysc.h index 5fcc9bc..2cbde65 100644 --- a/include/linux/platform_data/ti-sysc.h +++ b/include/linux/platform_data/ti-sysc.h @@ -49,7 +49,6 @@ struct sysc_regbits { s8 emufree_shift; }; -#define SYSC_MODULE_QUIRK_RTC_UNLOCK BIT(22) #define SYSC_QUIRK_CLKDM_NOAUTO BIT(21) #define SYSC_QUIRK_FORCE_MSTANDBY BIT(20) #define SYSC_MODULE_QUIRK_AESS BIT(19) diff --git b/include/linux/power/pwrseq.h b/include/linux/power/pwrseq.h new file mode 100644 index 0000000..cbc344c --- /dev/null +++ b/include/linux/power/pwrseq.h @@ -0,0 +1,81 @@ +#ifndef __LINUX_PWRSEQ_H +#define __LINUX_PWRSEQ_H + +#include + +#define PWRSEQ_MAX_CLKS 3 + +/** + * struct pwrseq - the power sequence structure + * @pwrseq_of_match_table: the OF device id table this pwrseq library supports + * @node: the list pointer to be added to pwrseq list + * @get: the API is used to get pwrseq instance from the device node + * @on: do power on for this pwrseq instance + * @off: do power off for this pwrseq instance + * @put: release the resources on this pwrseq instance + * @suspend: do suspend operation on this pwrseq instance + * @resume: do resume operation on this pwrseq instance + * @used: this pwrseq instance is used by device + */ +struct pwrseq { + const struct of_device_id *pwrseq_of_match_table; + struct list_head node; + int (*get)(struct device_node *np, struct pwrseq *p); + int (*on)(struct pwrseq *p); + void (*off)(struct pwrseq *p); + void (*put)(struct pwrseq *p); + int (*suspend)(struct pwrseq *p); + int (*resume)(struct pwrseq *p); + bool used; + bool suspended; +}; + +/* used for power sequence instance list in one driver */ +struct pwrseq_list_per_dev { + struct pwrseq *pwrseq; + struct list_head list; +}; + +#if IS_ENABLED(CONFIG_POWER_SEQUENCE) +void pwrseq_register(struct pwrseq *pwrseq); +void pwrseq_unregister(struct pwrseq *pwrseq); +struct pwrseq *of_pwrseq_on(struct device_node *np); +void of_pwrseq_off(struct pwrseq *pwrseq); +int of_pwrseq_on_list(struct device_node *np, struct list_head *head); +void of_pwrseq_off_list(struct list_head *head); +int pwrseq_suspend(struct pwrseq *p); +int pwrseq_resume(struct pwrseq *p); +int pwrseq_suspend_list(struct list_head *head); +int pwrseq_resume_list(struct list_head *head); +#else +static inline void pwrseq_register(struct pwrseq *pwrseq) {} +static inline void pwrseq_unregister(struct pwrseq *pwrseq) {} +static inline struct pwrseq *of_pwrseq_on(struct device_node *np) +{ + return NULL; +} +static void of_pwrseq_off(struct pwrseq *pwrseq) {} +static int of_pwrseq_on_list(struct device_node *np, struct list_head *head) +{ + return 0; +} +static void of_pwrseq_off_list(struct list_head *head) {} +static int pwrseq_suspend(struct pwrseq *p) +{ + return 0; +} +static int pwrseq_resume(struct pwrseq *p) +{ + return 0; +} +static int pwrseq_suspend_list(struct list_head *head) +{ + return 0; +} +static int pwrseq_resume_list(struct list_head *head) +{ + return 0; +} +#endif /* CONFIG_POWER_SEQUENCE */ + +#endif /* __LINUX_PWRSEQ_H */ diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 68782ba..91939f3 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -6410,6 +6410,8 @@ struct cfg80211_fils_resp_params { * not known. This value is used only if @status < 0 to indicate that the * failure is due to a timeout and not due to explicit rejection by the AP. * This value is ignored in other cases (@status >= 0). + * @authorized: Indicates whether the connection is ready to transport + * data packets. */ struct cfg80211_connect_resp_params { int status; @@ -6421,6 +6423,7 @@ struct cfg80211_connect_resp_params { size_t resp_ie_len; struct cfg80211_fils_resp_params fils; enum nl80211_timeout_reason timeout_reason; + bool authorized; }; /** @@ -6570,6 +6573,9 @@ cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid, * @resp_ie: association response IEs (may be %NULL) * @resp_ie_len: assoc response IEs length * @fils: FILS related roaming information. + * @authorized: true if the 802.1X authentication was done by the driver or is + * not needed (e.g., when Fast Transition protocol was used), false + * otherwise. Ignored for networks that don't use 802.1X authentication. */ struct cfg80211_roam_info { struct ieee80211_channel *channel; @@ -6580,6 +6586,7 @@ struct cfg80211_roam_info { const u8 *resp_ie; size_t resp_ie_len; struct cfg80211_fils_resp